ADA4807-1AKSZ-RL7 - 180MHz, 3.1nV/√Hz RRIO Op Amp | Analog Devices
MPN: ADA4807-1AKSZ-RL7 ✓ AktifADA4807-1AKSZ-RL7 Ringkasan
An operational amplifier (op amp) is a high-gain voltage amplifier with differential inputs and a single-ended output. It is a fundamental building block in analog signal conditioning, used to amplify, filter, or buffer signals. The ADA4807-1 belongs to the family of voltage feedback amplifiers, which are characterized by their ease of use, stable operation, and wide bandwidth. Within the hierarchy of analog ICs, it sits under linear amplifiers, which are essential in precision measurement, audio, and communication systems.
Key features include an input voltage noise density of 3.1 nV/√Hz and current noise of 0.7 pA/√Hz, which are among the lowest for high-speed RRIO amplifiers. The rail-to-rail input and output capability allows maximum dynamic range on low supply voltages, and the amplifier operates from a single 2.7 V to 5 V supply or dual ±1.35 V to ±2.5 V supplies. The disable pin (available on the SC-70-6 package) places the output in a high-impedance state, reducing quiescent current to near zero for power saving.
Technically, the ADA4807-1 uses a complementary bipolar process that achieves low distortion and high slew rate (225 V/µs) while maintaining low power. The amplifier is unity-gain stable and provides a phase margin of 60°, ensuring reliable operation in buffer configurations. Its output can swing within 50 mV of the rails, and the input common-mode range extends beyond the supplies, simplifying single-supply designs.
Typical applications include portable instrumentation, battery-powered audio, active filters, ADC drivers, and photodiode amplification. The low noise and high bandwidth make it suitable for medical devices, industrial sensors, and communication receivers where signal integrity is critical.
When designing with this amplifier, ensure proper decoupling of the supply pins with 0.1 µF ceramic capacitors placed close to the device. The disable pin should be tied to the positive supply if not used, to avoid accidental shutdown. For optimal noise performance, use metal-film resistors in the feedback network and keep the feedback loop short to minimize parasitic capacitance.
Alternatif penggantian untuk ADA4807-1AKSZ-RL7 — paket yang sama, pin-pada-pin kompatibel. Bagian paket yang berbeda memerlukan kerja ulang PCB diabaikan.
Variasi di dalam seri ini
Model-series yang sama yang kompatibel dengan penggantian ADA4807-1AKSZ-RL7 (sama faktor bentuk dan footprint) — berbeda di dalam Package / Case, Voltage - Supply Span (Max), Amplifier Type, Current - Supply, Gain Bandwidth Product.
ADA4807-1AKSZ-R7
✅ Drop-In📋 Alternatif referensi (tidak dalam katalog)
ADA4807-1AKSZ-R2
✅ Drop-In📋 Alternatif referensi (tidak dalam katalog)
ADA4805-1AKSZ-RL7
✅ Drop-InKontak untuk harga
Lihat Datasheet →ADA4805-1AKSZ
✅ Drop-InKontak untuk harga
Lihat Datasheet →OPA836
✅ Drop-In ⚠️ Spesifikasi Tidak Disahkan📋 Alternatif referensi (tidak dalam katalog)
LMH6643
✅ Drop-In ⚠️ Spesifikasi Tidak Disahkan📋 Alternatif referensi (tidak dalam katalog)
ADA4807-1AKSZ-RL7 Rating Maksimal & Karakteristik Listrik
| Amplifier Type | Voltage Feedback |
| Number of Circuits | 1 |
| Tipe Output | Rail-to-Rail |
| Slew Rate | 225 V/µs |
| Gain Bandwidth Product | 180 MHz |
| -3dB Bandwidth | 180 MHz |
| Current - Input Bias | 0.7 pA/√Hz (noise current density) |
| Voltage - Input Offset | 50 µV (typical) |
| Current - Supply | 1 mA |
| Current - Output / Channel | 60 mA |
| Voltage - Supply Span (Min) | 2.7 V |
| Voltage - Supply Span (Max) | 5 V |
| Suhu Kerja | -40°C to +125°C |
| Paket / Case | 6-TSSOP, SC-88, SOT-363 |
| Tipe Mounting | Surface Mount |
| Status RoHS | Compliant |
Konfigurasi Pin ADA4807-1AKSZ-RL7
| Pin produk 1 | OUT — Amplifier output |
| Pin produk 2 | GND — Ground (negative supply) |
| Pin produk 3 | IN+ — Non-inverting input |
| Pin produk 4 | IN- — Inverting input |
| Pin produk 5 | V+ — Positive supply |
| Pin produk 6 | DIS — Disable (active low) |
Aplikasi Umum
ADA4807-1AKSZ-RL7 cocok untuk 6 aplikasis: Portable Instrumentation, Battery-Powered Audio, Active Filters, ADC Driver, Photodiode Amplifier, Industrial Sensor Interface.
Portable Instrumentation
The ADA4807-1AKSZ-RL7's low power (1 mA) and low noise (3.1 nV/√Hz) make it ideal for battery-powered multimeters, data loggers, and handheld test equipment. Its rail-to-rail output maximizes dynamic range on 3.3 V supplies, and the small SC-70 package saves board space. The high bandwidth (180 MHz) ensures accurate amplification of fast transient signals, while the disable pin allows power saving between measurements.
Direkomendasikan
Battery-Powered Audio
With a quiescent current of only 1 mA and a supply range down to 2.7 V, the ADA4807-1AKSZ-RL7 is well-suited for portable audio devices such as MP3 players, smartphones, and hearing aids. Its low noise (3.1 nV/√Hz) ensures a clean audio signal, and the rail-to-rail output allows maximum headroom on low voltages. The 180 MHz bandwidth supports high-quality audio processing without slew-rate limiting.
Direkomendasikan
Active Filters
The ADA4807-1AKSZ-RL7's high gain bandwidth product (180 MHz) and low distortion make it an excellent choice for active filters in communication and instrumentation systems. It can implement Butterworth, Chebyshev, or Bessel filters with cutoff frequencies up to tens of MHz. The rail-to-rail input/output allows full-scale signal processing on low supplies, and the low noise ensures high signal-to-noise ratio in the passband.
Direkomendasikan
ADC Driver
The ADA4807-1AKSZ-RL7 can drive high-speed ADCs with its 60 mA output current and 180 MHz bandwidth. Its low noise and low distortion preserve signal integrity, while the rail-to-rail output maximizes the ADC's dynamic range. The disable pin allows power saving when the ADC is idle. It is suitable for driving 12-bit ADCs with sampling rates up to 100 MSPS.
Direkomendasikan
Photodiode Amplifier
The ADA4807-1AKSZ-RL7's low current noise (0.7 pA/√Hz) and low voltage noise (3.1 nV/√Hz) make it ideal for transimpedance amplifiers used in optical sensors, LIDAR, and medical diagnostics. The high bandwidth (180 MHz) allows fast pulse detection, and the low input bias current minimizes DC offset. The rail-to-rail output provides wide dynamic range for varying light levels.
Direkomendasikan
Industrial Sensor Interface
In industrial environments, the ADA4807-1AKSZ-RL7 can condition signals from temperature, pressure, and strain sensors. Its wide operating temperature range (-40°C to +125°C) and low power make it suitable for remote sensors. The rail-to-rail input allows direct interface with sensors that output near the supply rails, and the high bandwidth supports fast data acquisition.
Direkomendasikan
Ringkasan Produk Direkomendasikan
Data referensi engineering untuk ADA4807-1AKSZ-RL7 — pembandingan, panduan desain, dan informasi konformitas.
Panduan Pemilihan
Pembandingan dengan Alternatif
| Parameter Umum | Produk Ini | ADA4807-1AKSZ-R7 | ADA4805-1AKSZ-RL7 | OPA836 |
|---|---|---|---|---|
| Package | SC-70-6 | SC-70-6 | SC-70-6 | SC-70-6 |
| Brand | Analog Devices | Analog Devices | Analog Devices | Texas Instruments |
| Gain Bandwidth Product | 180 MHz | 180 MHz | 105 MHz | 205 MHz |
| Input Voltage Noise | 3.1 nV/√Hz | 3.1 nV/√Hz | 4.6 nV/√Hz | 4.6 nV/√Hz |
| Quiescent Current | 1 mA | 1 mA | 0.6 mA | 1 mA |
| Slew Rate | 225 V/µs | 225 V/µs | 120 V/µs | 260 V/µs |
| Supply Voltage Range | 2.7 V to 5 V | 2.7 V to 5 V | 2.7 V to 5 V | 2.5 V to 5.5 V |
| Disable Pin | Yes | Yes | Yes | No |
Diferensiator Kunci
- Lowest noise among high-speed RRIO amplifiers (vsOPA836)
- Integrated disable pin for power saving (vsOPA836)
- Lower quiescent current than comparable parts (vsLMH6643)
Catatan Desain
The ADA4807-1AKSZ-RL7 operates from 2.7 V to 5 V single supply. Use a 0.1 µF ceramic capacitor close to the V+ pin and a 10 µF bulk capacitor for low-frequency decoupling. For dual-supply operation, ensure both supplies are symmetrical and decoupled similarly.
For optimal noise performance, keep the feedback network components close to the amplifier and use a ground plane. Avoid routing high-speed digital traces near the input pins. The SC-70 package has a thermal pad; solder it to the PCB for improved heat dissipation.
The disable pin is active low. If unused, tie it to V+ to prevent accidental shutdown. Do not exceed the absolute maximum supply voltage of 6 V. Also, ensure the input common-mode voltage does not exceed the rails by more than 0.3 V to avoid latch-up.
Informasi Konformitas
RoHS and REACH compliant per distributor data. Not AEC-Q100 qualified.
