ATTINY261A-SU - 20MHz 8-bit AVR MCU | Microchip
MPN: ATTINY261A-SU ✓ AktifATTINY261A-SU Ringkasan
An 8-bit AVR microcontroller is a reduced-instruction-computing controller built around the AVR register and instruction architecture. Within the embedded-device hierarchy, it belongs to the MCU class, combines a CPU core with embedded memory and peripherals, and is programmed to supervise sensors, actuators, communications, and user interfaces. The ATTINY261A family is particularly appropriate for cost-sensitive control systems whose firmware and working data fit within 2 KB of Flash and 128 bytes of SRAM.
The device provides 32 general-purpose working registers, an 8-bit timer/counter with compare modes, an 8-bit high-speed timer/counter, a Universal Serial Interface, and internal system resources. Its 20 MHz operating speed gives embedded logic sufficient throughput for responsive control, while the 16 I/O lines allow connection of digital inputs, outputs, and mixed signal functions according to the device pin configuration. In-System Programmable Flash supports programming and firmware updates through the AVR programming interface.
The ATTINY261A is implemented as a high-performance picoPower 8-bit AVR RISC microcontroller. The ATtiny261A/461A/861A family uses an in-system-programmable Flash architecture and combines the 2 KB, 4 KB, or 8 KB memory configurations shown in the family datasheet. The ATTINY261A-SU corresponds to the 2 KB Flash configuration and is offered in a 20-pin SOIC tube package for standard industrial temperature operation.
Typical uses include compact motor or actuator controllers, LED dimming and lighting modules, sensor-interface nodes, low-power consumer accessories, power-control boards, and small industrial automation modules. Its combination of 20 MHz processing, two timers, a Universal Serial Interface, and 16 I/O lines supports control loops, pulse generation, serial communication, and discrete input monitoring without a larger external digital controller.
PCB design should preserve short, clean return paths for supply and ground and should follow the pin-specific decoupling and programming-interface guidance in the manufacturer datasheet. Because the SOIC package provides fine-pitch leads, verify land-pattern orientation and inspect solder joints carefully. Confirm the exact peripheral functions assigned to each I/O pin before defining the board schematic because alternate-function assignments vary by device variant and pin.
This technical summary organizes the controller’s memory, timing, I/O, package, migration, and design considerations for engineers evaluating the ATTINY261A-SU in a new embedded platform. It also distinguishes the verified original ATtiny261 migration path from unsupported assumptions about cross-brand equivalence, helping design teams make pin-, firmware-, and qualification-aware component decisions.
Alternatif penggantian untuk ATTINY261A-SU — paket yang sama, pin-pada-pin kompatibel. Bagian paket yang berbeda memerlukan kerja ulang PCB diabaikan.
Variasi di dalam seri ini
Model-series yang sama yang kompatibel dengan penggantian ATTINY261A-SU (sama faktor bentuk dan footprint) — berbeda di dalam Flash Memory, General-Purpose I/O Lines, General-Purpose Working Registers, Maximum Clock Frequency, Package.
ATTINY261
✅ Drop-In📋 Alternatif referensi (tidak dalam katalog)
ATTINY261A-SU Rating Maksimal & Karakteristik Listrik
| Product Type | 8-bit AVR RISC microcontroller |
| Frekuensi Bawah Maximum | 20 MHz |
| Flash Memory | 2 KB (1K x 16) |
| EEPROM | 128 bytes |
| SRAM | 128 bytes |
| General-Purpose I/O Lines | 16 lines |
| General-Purpose Working Registers | 32 registers |
| Timer/Counter | 8-bit timer/counter with compare modes |
| High-Speed Timer/Counter | 8-bit high-speed timer/counter |
| Serial Interface | Universal Serial Interface |
| Tegangan Pemuat | 2.5 V, 3.3 V, or 5 V |
| Suhu Kerja | -40°C to +85°C |
| Paket | 20-pin SOIC |
| Package Shipping Form | Tube |
| Programming | In-System Programmable Flash |
| Status RoHS | Compliant |
ATTINY261A-SU tube Diamant Konfigurasi Panduan
Konfigurasi pin untuk ATTINY261A-SU (tube pakai pakai). IC digital ini termasuk GPIO, antarmuka komunikasi (UART, SPI, I2C), dan pin kuasa. Lihat datasheet produsen untuk fungsi pin alternatif dan opsi konfigurasi. Penting untuk desain sistem pengemasan dan PCB.
Tidak ada data diatribut pin yang tersedia untuk ATTINY261A-SU.
Lihat ke: datasheet produk untuk konfigurasi pin penuh.
Aplikasi Umum
ATTINY261A-SU cocok untuk 6 aplikasis: Compact Sensor Interface Controller, LED Dimming and Lighting Control, Small Motor and Actuator Control, Power Control and Energy Management, Consumer Accessory Control, Embedded Communication Gateway Module.
Compact Sensor Interface Controller
The ATTINY261A-SU fits compact sensor nodes because it combines a 20 MHz AVR core with 16 general-purpose I/O lines and 128 bytes of SRAM. A design can sample digital sensor signals, apply threshold logic, and update an actuator without adding a larger processor. The 8-bit timer/counter and high-speed timer/counter provide timing resources for periodic sampling or pulse output, while the Universal Serial Interface can support a simple serial peripheral. The main constraint is firmware footprint: 2 KB of Flash and 128 bytes of SRAM favor direct control loops over elaborate protocol stacks.
Direkomendasikan
LED Dimming and Lighting Control
ATTINY261A-SU is appropriate for compact LED-driver and lighting-control modules where the required logic fits within 2 KB of Flash. Its 16 I/O lines can support switch inputs, status indicators, and digital control signals, while the two timer/counter sections can generate timing sequences for dimming, blinking, or effect patterns. The 20 MHz clock allows the firmware to service multiple time-based events, and the Universal Serial Interface can accommodate simple external control. Designers should account for the 128-byte SRAM limit and avoid allocating large display or animation buffers in RAM.
Direkomendasikan
Small Motor and Actuator Control
The ATTINY261A-SU can serve as the supervisory controller in a small motor or actuator module. Its 8-bit timer/counter with compare modes and separate 8-bit high-speed timer/counter support repeatable timing, pulse generation, and basic closed-loop update routines. Sixteen I/O lines provide control and status connections, while the 20 MHz operating rate permits responsive handling of limit switches, position signals, and operator commands. Because the MCU controls rather than directly drives most loads, external transistor or driver circuitry remains necessary. Firmware must also be sized around the 128-byte SRAM capacity.
Direkomendasikan
Power Control and Energy Management
ATTINY261A-SU is suitable for supervisory power-control boards that coordinate enable signals, monitor digital status, and implement startup sequences. Its low-resource AVR architecture is useful when the system needs deterministic local control rather than high-volume data processing. The timer/counter resources can measure timing windows or generate periodic control pulses, and the 16 I/O lines can connect to supervisory logic such as power-good signals and mode selects. Use the manufacturer electrical tables to choose clock and power-management settings for low-power operation, particularly when standby current contributes materially to the system budget.
Direkomendasikan
Consumer Accessory Control
The ATTINY261A-SU works well in a small consumer accessory that combines buttons, LEDs, a simple sensor, and a serial configuration interface. Its 16 I/O lines accommodate human-interface inputs and status outputs, while 2 KB of In-System Programmable Flash supports a compact state machine and calibration routine. The Universal Serial Interface may handle a simple host or peripheral connection, and EEPROM can preserve settings between power cycles. For battery-powered accessories, select the active, idle, and shutdown modes from the manufacturer electrical characteristics so the design meets its standby-current objective.
Direkomendasikan
Embedded Communication Gateway Module
ATTINY261A-SU can support a protocol-conversion or command-routing module when the required interface set is deliberately limited. The Universal Serial Interface provides a resource for serial link management, while 16 I/O lines can handle routing signals, mode indicators, and handshake controls. The 20 MHz clock is sufficient for lightweight command processing, and the 128-byte EEPROM can retain configuration values. This application has a tight boundary: the controller is best for small frame translators or supervisory bridges, not protocol stacks requiring substantial buffers, high-speed parallel data movement, or large lookup tables.
Direkomendasikan
Ringkasan Produk Direkomendasikan
Data referensi engineering untuk ATTINY261A-SU — pembandingan, panduan desain, dan informasi konformitas.
Panduan Pemilihan
Pembandingan dengan Alternatif
| Parameter Umum | Produk Ini | ATTINY261 |
|---|---|---|
| Package | 20-pin SOIC | 20-pin SOIC |
| Brand | Microchip Technology | Microchip Technology |
| Maximum Clock Frequency | 20 MHz | 20 MHz |
| Flash Memory | 2 KB | 2 KB |
| EEPROM | 128 bytes | 128 bytes |
| SRAM | 128 bytes | 128 bytes |
| General-Purpose I/O | 16 lines | 16 lines |
| General-Purpose Registers | 32 registers | 32 registers |
| Timer Resources | 8-bit timer/counter and 8-bit high-speed timer/counter | 8-bit timer/counter and 8-bit high-speed timer/counter |
| Manufacturing Process | ATtiny261A-family process | Earlier process; some electrical characteristics differ |
Diferensiator Kunci
- Documented functional migration from the earlier ATtiny261 (vsATTINY261)
- Full ATtiny261A product-page support for the 2 KB configuration (vsATTINY261)
- Compact 20-pin SOIC integration (vsATTINY261)
Catatan Desain
Use the 20-pin SOIC land pattern associated with the ATTINY261A package drawing and verify pin 1 orientation against the PCB silkscreen and manufacturer pin description. Keep the decoupling capacitor path between the supply and ground pins short, with a low-impedance ground return. Because the SOIC lead pitch is fine, inspect the assembled board under magnification for solder bridges, insufficient wetting, and solder wicking onto adjacent pins.
Select the operating clock and supply combination from the manufacturer electrical-characteristics tables, and include the external decoupling network required by the device. The controller supports 2.5 V, 3.3 V, and 5 V operation, but maximum current, sleep current, and startup behavior are separate specifications. For battery designs, estimate average current from processor active time, peripheral activity, and I/O loading rather than assuming the lowest mode current applies continuously.
Do not treat the documented functional equivalence between the original ATtiny261 and ATTINY261A as proof that every electrical characteristic is unchanged. Microchip’s AVR531 migration note states that the devices use different manufacturing processes and that some electrical characteristics differ. Revalidate timing margins, power measurements, reset behavior, and any application-specific qualification before releasing the A-family device into a production circuit.
Keep programming-interface signals accessible and isolate sensitive analog or timing-sensitive nodes from high-current switching paths. The Universal Serial Interface and timer outputs can use ordinary GPIO routing, but edge-sensitive functions should be kept away from switching-node copper and noisy power paths. Review alternate-function assignments in the pin-description table before finalizing net names; several I/O pins can serve more than one peripheral function.
Informasi Konformitas
The ATTINY261A-SU listing identifies the device as RoHS compliant. No automotive qualification, REACH status, lead-free classification, halogen-free classification, or conflict-minerals declaration was identified for this exact ordering code.