CD4056BFX - 16-Pin CMOS Counter and LCD Driver | Texas Instruments
MPN: CD4056BFX ✓ AktifCD4056BFX Ringkasan
A binary counter is a sequential digital circuit that divides an input clock into a corresponding binary value. An LCD decoder is a logic circuit that converts binary counter states into control signals for multiplexed liquid-crystal displays. The CD4056B combines both functions in one CMOS integrated circuit, placing it in the hierarchy of counter logic, display decoder, interface IC, and digital semiconductor.
Principal operating characteristics include a 3 V to 18 V supply range, low static current, propagation-delay and transition-time parameters, and decoded outputs suitable for driving display-control logic. The CD4056BFX is identified in military-temperature-grade listings and uses a through-hole package with 16 terminals. Its counter and decoder functions are useful when a design requires cascaded counting stages, direct display decoding, or a carry output for extending the count beyond the internal four-bit state.
The device operates from the same supply used by many legacy CMOS logic systems, allowing 5 V and 15 V implementations without a level-shifting stage. CMOS construction provides high noise immunity and low static power dissipation, although dynamic power and propagation delay rise as supply voltage and operating frequency increase. The clock, clock-inhibit, reset, and display-disable inputs provide the basic controls required for synchronous counting and display management.
Typical uses include laboratory counters, digital time and frequency indicators, industrial panel meters, event counters, and educational timing equipment. In each case, the decoded outputs reduce the logic required to select display segments or otherwise control the display system. Cascading counters can use the carry output to implement additional count ranges when one four-bit CD4056 stage is insufficient.
For a new through-hole design, preserve the manufacturer's specified pin functions and route the reset and display-disable inputs so they cannot float during power transitions. Confirm timing margin from the datasheet before operating near the maximum clock rate. Confirm supply sequencing, maximum input voltage, and unused-input states before releasing a production design.
Alternatif penggantian untuk CD4056BFX — paket yang sama, pin-pada-pin kompatibel. Bagian paket yang berbeda memerlukan kerja ulang PCB diabaikan.
Variasi di dalam seri ini
Model-series yang sama yang kompatibel dengan penggantian CD4056BFX (sama faktor bentuk dan footprint) — berbeda di dalam Logic Family, Product Type.
CD4056BE
✅ Drop-In ⚠️ Spesifikasi Tidak Disahkan📋 Alternatif referensi (tidak dalam katalog)
CD4056BF
✅ Drop-In ⚠️ Spesifikasi Tidak DisahkanKontak untuk harga
Lihat Datasheet →CD4056BM
✅ Drop-In ⚠️ Spesifikasi Tidak Disahkan📋 Alternatif referensi (tidak dalam katalog)
CD4056BP
✅ Drop-In ⚠️ Spesifikasi Tidak Disahkan📋 Alternatif referensi (tidak dalam katalog)
CD4056BF
✅ Drop-In ⚠️ Spesifikasi Tidak DisahkanKontak untuk harga
Lihat Datasheet →CD4056BFX Spesifikasi
| Product Type | LCD Driver |
| Counter and Decoder Supply Voltage | 3 V to 18 V |
| Logic Family | CMOS |
| Package Description | 14-CDIP |
| Terminal Count | 16 terminals |
| Tipe Mounting | Through-hole |
| Package Shape | Rectangular |
| Package Code | DIP |
| Temperature Grade | Military |
| Decoded Display Outputs | 4 outputs |
CD4056BFX dip Diamant Konfigurasi Panduan
Konfigurasi pin untuk CD4056BFX (dip pakai pakai). Penomoran pin, fungsi, dan diagram koneksi ditetapkan dalam datasheet produsen. Lihatnya untuk footprint dan pedoman perpindahan paruh.
Tidak ada data diatribut pin yang tersedia untuk CD4056BFX.
Lihat ke: datasheet produk untuk konfigurasi pin penuh.
Aplikasi Umum
CD4056BFX cocok untuk 6 aplikasis: Digital Frequency Counter, Laboratory Event Counter, Digital Timer Display, Industrial Panel Meter, Cascaded Count System, Educational Counter Trainer.
Digital Frequency Counter
The CD4056BFX suits digital frequency-counter front ends because it combines a binary counting stage with decoded display-control outputs. Its 3 V to 18 V CMOS supply range supports both 5 V and 15 V instrumentation, while the four decoded outputs reduce the logic needed to interface the count with multiplexed display circuitry. The carry output also permits additional counting stages when one internal four-bit count range is insufficient. Design the clock path for the required input bandwidth, use the manufacturer timing limits to establish setup and hold margins, and check unused control inputs so they remain in defined states.
Direkomendasikan
Laboratory Event Counter
The CD4056BFX can implement the central counting and decoding stage of a laboratory event counter. A pulse source clocks the device, the internal counter tracks successive events, and the decoded outputs support display-state control. With a 3 V to 18 V operating range, it can share the supply domain of suitable CMOS logic and reduce component count compared with separate counter and decoder ICs. For reliable operation, set input levels to valid CMOS thresholds, define reset behavior during startup, and use the manufacturer propagation-delay and maximum-frequency characteristics when choosing the pulse-source frequency.
Direkomendasikan
Digital Timer Display
The CD4056BFX is appropriate for digital timer displays because it provides a binary counter, decoded outputs, and a high-count indication in a single package. The decoded outputs can control display selection logic while the counter advances from a time-base signal. Its CMOS supply range of 3 V to 18 V allows operation beside compatible 5 V or 15 V display circuitry. Designers should account for propagation delay between clock and decoded outputs, ensure the display-disable and reset inputs have defined startup states, and verify that the time-base frequency remains comfortably below the applicable operating-frequency limit.
Direkomendasikan
Industrial Panel Meter
The CD4056BFX can serve as a counter-to-display interface in an industrial panel meter, especially where a legacy CMOS control board already uses through-hole DIP devices. Four decoded outputs and the high-count output simplify the logic required to translate count states into display commands. The 3 V to 18 V supply range supports common industrial logic voltages, but the design must still address input noise, clock edge quality, and reset release timing. Confirm the exact package and temperature grade for the installed board, and validate display timing across the full intended supply and temperature range.
Direkomendasikan
Cascaded Count System
The CD4056BFX can form one stage of a cascaded counting system by using its carry output to clock a subsequent stage when a larger count range is needed. This arrangement supports equipment requiring more than the internal four-bit count range without implementing every counter stage separately. The device's 3 V to 18 V operating range allows the stages to operate from a common CMOS supply when timing and noise margins permit. Check the carry-output delay before adding clock phase, and use the manufacturer maximum-frequency values to ensure the highest-frequency stage retains adequate timing margin.
Direkomendasikan
Educational Counter Trainer
The CD4056BFX is useful in educational counter and digital-logic trainers because it exposes counting, decoded display control, clock, inhibit, and reset functions in a through-hole package. Students can observe counter states and display sequencing without assembling separate decoder logic. Its 3 V to 18 V supply range permits common laboratory rails and makes input-state experimentation straightforward. Build the trainer so unused inputs are pulled to defined logic levels, avoid leaving clock lines long in high-impedance environments, and present reset and display-disable controls in a way that allows students to understand their effects on operating states.
Direkomendasikan
Ringkasan Produk Direkomendasikan
Data referensi engineering untuk CD4056BFX — pembandingan, panduan desain, dan informasi konformitas.
Panduan Pemilihan
Pembandingan dengan Alternatif
| Parameter Umum | Produk Ini | CD4056BE | CD4056BF | CD4056BM | CD4056BP | CD4056B |
|---|---|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | Through-hole DIP; listing conflict between 14-CDIP and 16 terminals | 16-pin DIP | 16-pin DIP | 16-pin DIP | 16-pin DIP | 16-pin DIP |
| Logic Family | CMOS | CMOS | CMOS | CMOS | CMOS | CMOS |
| Supply Voltage | 3 V to 18 V | 3 V to 18 V | 3 V to 18 V | 3 V to 18 V | 3 V to 18 V | 3 V to 18 V |
| Mounting Type | Through-hole | Through-hole | Through-hole | Through-hole | Through-hole | Through-hole |
| Decoded Outputs | 4 outputs | 4 outputs | 4 outputs | 4 outputs | 4 outputs | 4 outputs |
Diferensiator Kunci
- Combined counter and decoded display outputs (vsCD4056BE)
- Exact package-grade option for legacy DIP hardware (vsCD4056BF)
- Military-temperature ordering designation (vsCD4056BP)
Catatan Desain
Verify the physical package before ordering or replacing CD4056BFX. Current distributor records conflict between a 14-CDIP description and a separate 16-terminal DIP record. Compare the installed outline, lead spacing, pin-1 marking, and manufacturer pin-description table before assigning connections. A matching CD4056B family name does not by itself prove that every suffix has the same lead arrangement.
Keep the clock route short and driven by a source with compatible CMOS output levels. Propagation delay accumulates through cascaded counter stages, so leave timing margin against the manufacturer maximum-frequency and transition-time limits. Do not allow clock, clock-inhibit, reset, or display-disable inputs to float. Defined biasing prevents false counting during startup or when an external connector is disconnected.
Preserve adequate clearance around the DIP footprint and route supply and return paths to minimize loop area. Place the normal bypass capacitor close to the device supply pins when the board layout is being revised. For an existing through-hole board, inspect the socket, solder joints, and copper corrosion before assuming that a replacement failure is caused by the integrated circuit itself.
Informasi Konformitas
A military temperature grade is identified for CD4056BFX. RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations are not stated in the referenced product records and require confirmation from the manufacturer.