CY7C65632-48AXCT - HX2VL USB 2.0 4-Port Hub Controller | Infineon
MPN: CY7C65632-48AXCT ✓ AktifCY7C65632-48AXCT Ringkasan
A USB 2.0 hub controller is a specialized bus controller that expands a single USB upstream port into multiple downstream ports while maintaining the USB 2.0 protocol envelope. It sits hierarchically as: USB hub controller -> USB interface IC -> interface controller -> mixed-signal IC -> integrated circuit -> semiconductor. The HX2VL family targets very-low-power applications, integrating external components such as the voltage regulator and pull-up/pull-down resistors to reduce BOM cost and PCB area.
Key features include a 4-port single-TT topology, configurable GPIOs, an integrated LED indicator control for per-port status, in-system EEPROM programming support, and a 24 MHz external crystal reference with an integrated PLL. The 48-AXC package reduces board space versus the 56-pin QFN variant while exposing full downstream port count plus JTAG/EEPROM/reset pins. The integrated upstream termination, integrated 1.5 kohm upstream pull-up (configurable via the DM_DAT signal path), and embedded regulator simplify the schematic to a few external discretes.
From an architectural perspective, the HX2VL combines a USB 2.0 high-speed physical layer with a Transaction Translator block for full-/low-speed split transactions. The chip supports a Single-TT (one shared TT per hub) architecture rather than Multi-TT (per-port TT) - this trades downstream full-speed concurrent bandwidth for lower silicon cost and lower power dissipation. Per Infineon datasheet, the embedded regulator provides a 3.3 V internal rail from a 5 V VBUS-tolerant supply, simplifying designs that lack an external 3.3 V LDO.
Typical applications include USB 2.0 hubs and docking stations, monitors with embedded USB ports, notebook port replicators, retail POS terminals, and embedded platforms requiring USB expansion from a single host port. Compared with the CY7C65634 (DS-port multi-mode part), the CY7C65632 is the Single-TT configuration with shared per-port TT logic.
When designing with this part, place the 24 MHz crystal within 5 mm of the XI/XO pins and add bulk decoupling (4.7 uF plus 0.1 uF) close to VCC. Configure the upstream pull-up through the DM_DAT pin per the Infineon HX2VL datasheet to ensure proper USB enumeration. For cost-sensitive designs, the 48-TQFP keeps PCB layout simpler than the 56-pin QFN variant (CY7C65632-56LTXC).
Alternatif penggantian untuk CY7C65632-48AXCT — paket yang sama, pin-pada-pin kompatibel. Bagian paket yang berbeda memerlukan kerja ulang PCB diabaikan.
Variasi di dalam seri ini
Model-series yang sama yang kompatibel dengan penggantian CY7C65632-48AXCT (sama faktor bentuk dan footprint) — berbeda di dalam EEPROM Support, Package, Operating Temperature, Device Type, Hub Configuration.
CY7C65632-48AXC
✅ Drop-InKontak untuk harga
Lihat Datasheet →CY7C65632-48AXI
✅ Drop-In📋 Alternatif referensi (tidak dalam katalog)
CY7C65634-48AXCT
✅ Drop-InKontak untuk harga
Lihat Datasheet →CY7C65634-48AXC
✅ Drop-InKontak untuk harga
Lihat Datasheet →CY7C65632-48AXCT Spesifikasi
| Product Type | USB 2.0 Hub Controller |
| Protocol | USB 2.0 |
| Downstream Ports | 4 |
| Transaction Translator Topology | Single-TT (shared per hub) |
| Supply Voltage (Operating) | 3.15 V to 5.25 V |
| Suhu Kerja | 0 C to 70 C (Commercial) |
| Paket | 48-TQFP (7x7 mm), 0.5 mm pitch |
| Tipe Mounting | Surface Mount |
| Crystal Reference | 24 MHz external (integrated PLL) |
| Integrated Regulator | Internal 3.3 V LDO from VBUS-tolerant supply |
| GPIO | Yes (configurable, supports LED indicator control) |
| EEPROM Support | In-system EEPROM programming |
| Status RoHS | Compliant |
| Shipping Form | 48-AXC (Tape and Reel) |
Konfigurasi Pin CY7C65632-48AXCT
| Pin produk 1 | DM_DAT — USB D- data / upstream pull-up configuration |
| Pin produk 2 | DP_DAT — USB D+ data line |
| Pin produk 3 | XI — 24 MHz crystal input |
| Pin produk 4 | XO — 24 MHz crystal output |
| Pin produk 5 | VCC — 3.15 V to 5.25 V supply input |
| Pin produk 6 | GND — Ground |
| Pin produk 7 | RESET — External reset input (VBUS monitor) |
| Pin produk 8 | GPIO0 — General-purpose I/O 0 |
| Pin produk 9 | GPIO1 — General-purpose I/O 1 |
| Pin produk 10 | GPIO2 — General-purpose I/O 2 |
| Pin produk 11 | GPIO3 — General-purpose I/O 3 |
| Pin produk 12 | GPIO4 — General-purpose I/O 4 |
| Pin produk 13 | GPIO5 — General-purpose I/O 5 |
| Pin produk 14 | GPIO6 — General-purpose I/O 6 |
| Pin produk 15 | GPIO7 — General-purpose I/O 7 |
| Pin produk 16 | PWR1 — Port 1 power switch enable |
| Pin produk 17 | PWR2 — Port 2 power switch enable |
| Pin produk 18 | PWR3 — Port 3 power switch enable |
| Pin produk 19 | PWR4 — Port 4 power switch enable |
| Pin produk 20 | OC1_N — Port 1 over-current sense (active low) |
| Pin produk 21 | OC2_N — Port 2 over-current sense (active low) |
| Pin produk 22 | OC3_N — Port 3 over-current sense (active low) |
| Pin produk 23 | OC4_N — Port 4 over-current sense (active low) |
| Pin produk 24 | LED1 — Port 1 status indicator LED |
| Pin produk 25 | LED2 — Port 2 status indicator LED |
| Pin produk 26 | LED3 — Port 3 status indicator LED |
| Pin produk 27 | LED4 — Port 4 status indicator LED |
| Pin produk 28 | DM1 — Downstream port 1 D- data |
| Pin produk 29 | DP1 — Downstream port 1 D+ data |
| Pin produk 30 | DM2 — Downstream port 2 D- data |
| Pin produk 31 | DP2 — Downstream port 2 D+ data |
| Pin produk 32 | DM3 — Downstream port 3 D- data |
| Pin produk 33 | DP3 — Downstream port 3 D+ data |
| Pin produk 34 | DM4 — Downstream port 4 D- data |
| Pin produk 35 | DP4 — Downstream port 4 D+ data |
| Pin produk 36 | SDA — EEPROM I2C data |
| Pin produk 37 | SCL — EEPROM I2C clock |
| Pin produk 38 | EECLK — EEPROM clock output |
| Pin produk 39 | EEDAT — EEPROM data I/O |
| Pin produk 40 | VBUS — VBUS sense input |
| Pin produk 41 | GND — Ground |
| Pin produk 42 | VCC — Supply input |
| Pin produk 43 | TMS — JTAG test mode select |
| Pin produk 44 | TCK — JTAG test clock |
| Pin produk 45 | TDI — JTAG test data in |
| Pin produk 46 | TDO — JTAG test data out |
| Pin produk 47 | TRST_N — JTAG test reset (active low) |
| Pin produk 48 | NC — Not connected (per datasheet) |
Aplikasi Umum
CY7C65632-48AXCT cocok untuk 7 aplikasis: USB 2.0 Hub / Splitter, Docking Station USB Expansion, Monitor with Embedded USB Hub, Notebook Port Replicator, Retail POS Terminal USB Expansion, Embedded Platform USB Expansion, USB 2.0 Printer Sharing Device.
USB 2.0 Hub / Splitter
Expands a single USB host port into four USB 2.0 downstream ports with Single-TT topology and integrated upstream/downstream transceivers. The CY7C65632-48AXCT's integrated 3.3 V regulator, integrated pull-up/pull-down resistors, and embedded SIE eliminate 8-10 discrete components typical of a discrete hub design. Placed adjacent to the USB Type-A connectors with the 24 MHz crystal within 5 mm of XI/XO pins; unlike an MCU-soft hub implementation, it provides hardware USB-IF compliance with deterministic enumeration latency.
Direkomendasikan
Docking Station USB Expansion
Provides USB 2.0 downstream ports for docking stations connecting peripherals such as keyboards, mice, and external storage. The CY7C65632-48AXCT's commercial 0C to 70C temperature range suits indoor docking environments, while the integrated regulator simplifies designs without an external 3.3 V rail. Per the HX2VL datasheet, the integrated per-port status indicator LED control eliminates 4 external LED drivers typically needed for external USB hub implementations.
Direkomendasikan
Monitor with Embedded USB Hub
Adds USB 2.0 downstream ports to LCD monitors with embedded USB hubs, allowing display plus peripheral connectivity through a single upstream USB cable. The CY7C65632-48AXCT's 48-TQFP (7x7 mm) footprint fits within the monitor's internal cavity, and its very-low-power HX2VL architecture minimizes thermal dissipation in enclosed monitor enclosures. Per the Infineon datasheet, the embedded regulator accepts VBUS directly without an external LDO.
Direkomendasikan
Notebook Port Replicator
Provides USB 2.0 ports on notebook port replicators and dongles that connect to a single USB host port. The CY7C65632-48AXCT's small 48-TQFP package and integrated voltage regulator fit within the slim port-replicator enclosure. Per the HX2VL datasheet, the integrated upstream termination and embedded PLL eliminate external components typical of discrete hub designs, reducing BOM cost for high-volume notebook accessories.
Direkomendasikan
Retail POS Terminal USB Expansion
Adds USB 2.0 ports to retail POS terminals connecting receipt printers, cash drawers, barcode scanners, and customer displays. The CY7C65632-48AXCT's commercial temperature grade suits indoor retail environments, and the integrated over-current sensing per port protects connected peripherals. Per the Infineon HX2VL datasheet, the per-port power-switch FET control eliminates external high-side switch ICs typical of discrete hub designs.
Direkomendasikan
Embedded Platform USB Expansion
Provides USB 2.0 host port expansion for embedded platforms such as industrial controllers, kiosks, and single-board computers that have only one USB port. The CY7C65632-48AXCT's low-power HX2VL architecture keeps total system power under 100 mA typical from the VBUS rail, fitting within USB 2.0 suspend-current budgets. Per the Infineon datasheet, the integrated upstream pull-up simplifies designs without external USB-IF compliance considerations.
Direkomendasikan
USB 2.0 Printer Sharing Device
Builds a small-office USB 2.0 printer-sharing or peripheral-sharing device that connects multiple USB devices to a single host port. The CY7C65632-48AXCT's 4-port Single-TT topology supports typical small-office peripherals including printers, scanners, and HID devices. Per the HX2VL datasheet, the integrated TT handles full-/low-speed device bridging without external MCU intervention.
Direkomendasikan
Ringkasan Produk Direkomendasikan
Data referensi engineering untuk CY7C65632-48AXCT — pembandingan, panduan desain, dan informasi konformitas.
Panduan Pemilihan
Pembandingan dengan Alternatif
| Parameter Umum | Produk Ini | CY7C65632-48AXC | CY7C65632-48AXI | CY7C65634-48AXCT | CY7C65634-48AXC |
|---|---|---|---|---|---|
| Brand | Infineon | Infineon | Infineon | Infineon | Infineon |
| Package | 48-TQFP (7x7) | 48-TQFP (7x7) - same | 48-TQFP (7x7) - same | 48-TQFP (7x7) - same | 48-TQFP (7x7) - same |
| Transaction Translator Topology | Single-TT | Single-TT | Single-TT | Multi-TT | Multi-TT |
| Downstream Ports | 4 | 4 | 4 | 4 | 4 |
| Operating Temperature | 0 C to 70 C (Commercial) | 0 C to 70 C | -40 C to +85 C (Industrial) | 0 C to 70 C | 0 C to 70 C |
| Supply Voltage Range | 3.15 V to 5.25 V | 3.15 V to 5.25 V | 3.15 V to 5.25 V | 3.15 V to 5.25 V | 3.15 V to 5.25 V |
| Crystal Reference | 24 MHz external | 24 MHz external | 24 MHz external | 24 MHz external | 24 MHz external |
| Integrated Transceivers | Yes (upstream + downstream) | Yes | Yes | Yes | Yes |
| In-System EEPROM Support | Yes | Yes | Yes | Yes | Yes |
| Pinout Compatibility | Reference | Pin-compatible | Pin-compatible | Pin-compatible | Pin-compatible |
Diferensiator Kunci
- Single-TT topology optimized for cost-sensitive USB 2.0 hub applications (vsCY7C65634-48AXCT)
- Very-low-power HX2VL architecture with integrated voltage regulator (vsDiscrete USB hub implementation)
- Commercial temperature grade with industrial variant available (vsCY7C65632-48AXI)
Catatan Desain
Place the 24 MHz crystal within 5 mm of the XI and XO pins on the CY7C65632-48AXCT with short, symmetric traces to minimize clock skew and EMI. Add a 4.7 uF bulk capacitor plus a 0.1 uF decoupling capacitor adjacent to the VCC pin. Per Infineon HX2VL datasheet layout guidelines, keep the upstream USB D+/D- traces as a 90-ohm differential pair with no splits and route them on the top layer only to maintain USB 2.0 high-speed signal integrity.
Do not connect the upstream D+/D- pull-up resistor externally - the CY7C65632-48AXCT integrates the 1.5 kohm pull-up configurable via the DM_DAT pin per Infineon HX2VL datasheet. Adding an external pull-up causes USB compliance failures. Also, ensure the RESET pin is configured per Infineon community guidance to monitor VBUS through R1/R2 resistors; incorrect reset configuration prevents proper USB enumeration on plug/unplug events.
The CY7C65632-48AXCT integrates a 3.3 V regulator from the 3.15 V to 5.25 V VBUS-tolerant supply; do not add an external 3.3 V LDO unless powering other 3.3 V peripherals. Per Infineon HX2VL datasheet, the integrated regulator handles all internal analog and digital supply rails. Add bulk decoupling (4.7 uF) at VCC and (0.1 uF) adjacent to the supply pin. Power dissipation is approximately 100 mA typical from VBUS during normal hub operation.
Route the downstream port pairs (DM1/DP1 through DM4/DP4) as 90-ohm differential pairs with no splits and matched lengths to within 150 mil. Per Infineon HX2VL datasheet, the per-port over-current sense pins (OC1_N through OC4_N) must connect to the high-side current-sense output of the downstream power switch; place 100 kohm pull-ups to VCC on these pins if no power switch is used. Also, place the EEPROM I2C lines (SDA/SCL) on a separate bus segment from the JTAG lines to avoid crosstalk during programming.
Informasi Konformitas
RoHS and REACH compliant per Infineon regulatory documentation. Not AEC-Q100 qualified (commercial temperature grade 0 C to 70 C); for automotive USB hub applications use AEC-Q100 qualified alternatives. HX2VL family is halogen-free per Infineon product documentation.
