CY8C3665AXI-198 - 67MHz 32KB PSoC 3 MCU | Infineon
MPN: CY8C3665AXI-198 ✓ AktifCY8C3665AXI-198 Ringkasan
A PSoC 3, or Programmable System-on-Chip, integrates a microcontroller core with configurable digital and analog resources on one mixed-signal device. This MCU belongs to the CY8C36xx family, where designers can use universal digital blocks to implement timers, counters, serial interfaces, and custom logic alongside the 8051 processor. That integration can reduce the need for separate peripheral ICs when the required functions are appropriately partitioned and the design is verified against the family architecture.
The most prominent device characteristics are its 67 MHz operating frequency, 32 kByte program flash, 4 kByte SRAM, 16 universal digital blocks, and 62 available I/O pins. The 100-lead TQFP footprint provides extensive routing access for external sensors, displays, communication transceivers, actuators, and mixed-signal conditioning networks. Unlike a small-pin-count MCU, the large perimeter package also makes it practical to distribute signals around a multi-layer board.
The CY8C36xx architecture supports an embedded 8051 instruction set alongside programmable system resources. The universal digital blocks can be arranged into configurations such as timers, counters, serial channels, and custom functions, allowing firmware to map peripheral behavior to application requirements. Designers should consult the manufacturer datasheet for the exact block counts, trigger routing, clock limits, and electrical operating ranges of the selected configuration.
Typical uses include industrial control panels, sensor-conditioning equipment, motor and actuator controllers, user-interface modules, communications equipment, and compact consumer products. The 62 I/O pins are especially useful when a design connects several sensors, indicator drivers, relay outputs, or serial interfaces. For designs needing higher analog precision or more analog peripherals, a different PSoC family member may be a better architectural fit.
When laying out the board, provide short, direct return paths for supply and ground pins and route sensitive analog signals away from digital switching nodes. Confirm package dimensions, pin functions, exposed-pad requirements, and recommended PCB land patterns in the manufacturer package drawings before releasing artwork.
This page combines the manufacturer product overview with practical selection guidance, a parameter comparison against related PSoC 3 devices, and design notes covering decoupling, clocking, signal integrity, and firmware planning. These engineering resources support an early architecture decision while the complete datasheet remains the controlling document for implementation.
Alternatif penggantian untuk CY8C3665AXI-198 — paket yang sama, pin-pada-pin kompatibel. Bagian paket yang berbeda memerlukan kerja ulang PCB diabaikan.
Variasi di dalam seri ini
Model-series yang sama yang kompatibel dengan penggantian CY8C3665AXI-198 (sama faktor bentuk dan footprint) — berbeda di dalam Product Type, Package, Core Architecture, Flash Memory, Flash Organization.
CY8C3665AXA-010
✅ Drop-InKontak untuk harga
Lihat Datasheet →CY8C3865AXI-019
✅ Drop-In📋 Alternatif referensi (tidak dalam katalog)
CY8C3865AXA-018
✅ Drop-InKontak untuk harga
Lihat Datasheet →CY8C3665AXI-198 Rating Maksimal & Karakteristik Listrik
| Product Type | 8-bit PSoC 3 microcontroller |
| Product Family | CY8C36xx |
| Processor Architecture | 8051 |
| Maximum Operating Frequency | 67 MHz |
| Program Flash Memory | 32 kByte |
| Flash Organization | 32K x 8 bits |
| SRAM | 4 kByte |
| Universal Digital Blocks | 16 |
| I/O Pin Count | 62 pins |
| Paket | 100-pin TQFP |
| Package Body Size | 14 x 14 mm |
| Tipe Mounting | Surface mount |
CY8C3665AXI-198 14 x 14 mm Diamant Konfigurasi Panduan
Konfigurasi pin untuk CY8C3665AXI-198 (14 x 14 mm pakai pakai). IC digital ini termasuk GPIO, antarmuka komunikasi (UART, SPI, I2C), dan pin kuasa. Lihat datasheet produsen untuk fungsi pin alternatif dan opsi konfigurasi. Penting untuk desain sistem pengemasan dan PCB.
Tidak ada data diatribut pin yang tersedia untuk CY8C3665AXI-198.
Lihat ke: datasheet produk untuk konfigurasi pin penuh.
Aplikasi Umum
CY8C3665AXI-198 cocok untuk 6 aplikasis: Industrial Control and Sensor Interface Module, Capacitive-Touch User Interface Controller, Motor and Actuator Control Board, Communications Gateway and Protocol Bridge, Compact Instrumentation and Data-Acquisition Front End, LED Lighting and Display Sequencer.
Industrial Control and Sensor Interface Module
The CY8C3665AXI-198 fits industrial control modules that must combine several sensor inputs with discrete control outputs. Its 62 I/O pins provide substantial routing capacity for digital sensors, relay drivers, status indicators, and field-bus transceivers, while the 16 universal digital blocks can implement timers, counters, serial channels, or custom logic. The 67 MHz 8051-class core gives firmware headroom for protocol handling, filtering, and supervisory control. Confirm operating temperature, supply range, and EMC requirements in the device datasheet before deploying the module in a regulated industrial enclosure.
Direkomendasikan
Capacitive-Touch User Interface Controller
The CY8C3665AXI-198 can serve as the host for a capacitive-touch keypad or rotary control panel because its 62 available I/O pins provide ample connections to external sensors and display-control devices. Programmable digital blocks support timing and custom scanning logic, while 32 kByte of flash and 4 kByte of SRAM support touch firmware, debouncing, and communication routines. Design the analog sensing path according to the PSoC 3 application guidance, maintain clean grounding near the touch controller, and avoid routing fast digital edges beneath the sensing area.
Direkomendasikan
Motor and Actuator Control Board
The CY8C3665AXI-198 is appropriate for a compact actuator controller that coordinates position sensing, timing, and output sequencing. Sixteen universal digital blocks can be configured for timer, counter, and capture functions, while the 62 I/O pins can connect encoders, Hall-effect sensors, limit switches, motor drivers, and status LEDs. The 67 MHz processor supports responsive closed-loop control and diagnostic routines. Validate pulse-width limits, pin drive capability, and noise margins against the specific motor driver and sensing interface in the manufacturer datasheet.
Direkomendasikan
Communications Gateway and Protocol Bridge
The CY8C3665AXI-198 works well as a protocol-conversion gateway when one board must terminate several low-speed serial interfaces and forward data to a faster host. Its 62 I/O pins leave enough routing capacity for multiple UART-style connections, status indicators, and configuration controls, while the programmable digital blocks can support custom baud-rate generation and framing. The 32 kByte flash budget can hold protocol tables and boot logic. Verify the supported serial peripherals, interrupt vectors, and maximum peripheral clock against the device documentation.
Direkomendasikan
Compact Instrumentation and Data-Acquisition Front End
The CY8C3665AXI-198 can manage a compact data-acquisition front end that gathers digital measurements, controls analog-support circuitry, and reports results to a host processor. Its programmable digital architecture supports timing, trigger, and custom logic functions, while 62 I/O pins allow simultaneous connection of sensors, multiplexers, and status lines. The 4 kByte SRAM supports short acquisition buffers, and the 67 MHz core can process filtering and conversion control. Use the manufacturer layout guidance to isolate sensitive analog nodes and provide local bypass capacitance at each supply pin.
Direkomendasikan
LED Lighting and Display Sequencer
The CY8C3665AXI-198 is suitable for an LED animation, signage, or multi-zone lighting controller where many outputs must be sequenced precisely. The 16 universal digital blocks can form timer, counter, and serial structures, and the 62 I/O pins can drive external LED drivers, level-shifters, and control switches. Its 32 kByte flash capacity accommodates animation tables and effect libraries, while the 67 MHz processor allows smooth timing updates. Account for LED-driver current, switching-node noise, and common-anode or common-cathode wiring in the final board design.
Direkomendasikan
Ringkasan Produk Direkomendasikan
Data referensi engineering untuk CY8C3665AXI-198 — pembandingan, panduan desain, dan informasi konformitas.
Panduan Pemilihan
Pembandingan dengan Alternatif
| Parameter Umum | Produk Ini | CY8C3665AXA-010 | CY8C3865AXI-019 | CY8C3865AXA-018 |
|---|---|---|---|---|
| Brand | Infineon Technologies | Infineon Technologies | Infineon Technologies | Infineon Technologies |
| Package | 100-pin TQFP (14x14 mm) | 100-pin TQFP | 100-pin TQFP | 100-pin TQFP |
| Product Series | CY8C36xx PSoC 3 | CY8C36xx PSoC 3 | CY8C3865 PSoC | CY8C3865 PSoC |
| Processor Architecture | 8051 | 8051 | 8051 / RISC | 8051 / RISC |
| Program Flash | 32 kByte | 32 kByte | 32 kByte | 32 kByte |
Diferensiator Kunci
- High pin connectivity in a compact 14 x 14 mm package (vsCY8C3865AXI-019)
- Sixteen programmable universal digital blocks (vsCY8C3865AXA-018)
- 67 MHz operation with 32 kByte flash (vsCY8C3665AXA-010)
Catatan Desain
Estimated: supply-current budgeting must be performed with the device operating frequency and the selected peripheral set. Use the manufacturer operating-current tables for run, sleep, and low-power modes, then add the external load on every active I/O. Place the recommended bypass capacitors adjacent to the supply pins and maintain a continuous ground plane beneath the device. Do not estimate rail droop from laboratory supply readouts because switching I/O and high-frequency core activity are local to the package.
Route the 100-pin TQFP using the manufacturer land pattern and verify pin-1 orientation against the package drawing. The 62 usable I/O pins should be assigned by function so high-switching outputs remain away from sensitive analog inputs. Keep decoupling connections short, provide a low-impedance return path for each supply connection, and check that programming and debug signals have unobstructed routing under the package. Final artwork should be reviewed against the recommended manufacturing and assembly drawings.
Plan clock and digital timing margins before committing to external interfaces. The 67 MHz core can expose edge-rate problems that are invisible at lower clock rates, particularly when the board contains long traces, connectors, or adjacent high-current switching circuitry. Follow the documented drive-strength and configuration options, avoid unnecessary stubs, and use continuous reference planes for high-speed links. Validate signal timing with an oscilloscope or logic analyzer on the first assembled boards.
Do not treat a matching TQFP package as proof of software or electrical interchangeability. Review the complete pin-description table, alternate functions, clock limits, and peripheral resources for every substitute device. The CY8C3665, CY8C3865, and related ordering suffixes may change speed grade, temperature range, qualification, or production status. Rebuild or validate the PSoC configuration when moving between device series instead of carrying over configuration files without inspection.
Informasi Konformitas
Compliance status must be confirmed from the manufacturer declaration or material-declaration documentation for the exact ordering code and production lot.