DG412CY+T - 45Ω Quad SPST Analog Switch | Analog Devices
MPN: DG412CY+T ✓ AktifDG412CY+T Ringkasan
An analog switch is a semiconductor device that connects or disconnects a signal path under digital control. A quad SPST switch contains four separate SPST channels rather than one multiplexed channel. In the broader hierarchy, the DG412CY+T is an analog switch, an interface IC, and a semiconductor designed to bridge external analog circuitry with digital control logic. This makes it useful wherever several independent signals must be routed under software or hardware control.
Key electrical features include maximum on-resistance matching of 3 Ω and guaranteed on-resistance flatness across the signal range of 4 Ω. The device also provides low charge injection, low power consumption, and bidirectional operation. According to the Analog Devices DG412 product page, the switch family guarantees ESD tolerance of at least 2000 V under Method 3015.7. These characteristics help preserve signal integrity when switch transitions can disturb sensitive analog nodes.
The DG412CY+T uses CMOS technology and provides four independent SPST circuits rather than a multiplexed configuration. Its maximum on-resistance of 45 Ω is appropriate for many control and instrumentation signals where insertion loss is not the dominant concern. Bidirectional conduction means the same terminal pair can carry signal in either direction while the switch is closed, simplifying routing symmetry and reducing the number of signal-direction assumptions in system design.
Typical uses include automated test equipment, data acquisition systems, sample-and-hold isolation, peripheral selection, battery and power-system routing, and analog signal conditioning. The four independent channels are especially useful when a controller must select sensors, connect external instrumentation, or isolate several signal sources. Designers should evaluate charge injection and switching transients when driving high-impedance or precision measurement nodes.
For PCB implementation, route each switched signal directly to the assigned IN and OUT pins, place the device close to the signals it controls, and keep digital control traces away from sensitive analog conductors. Confirm the control-logic polarity and off-state behavior in the application circuit, and account for the 45 Ω on-resistance when calculating source impedance, settling time, and allowable attenuation.
This page combines the manufacturer’s device information with drop-in alternatives, parameter comparisons, application guidance, and practical layout considerations. It is intended to help engineers identify a pin-compatible part, verify the electrical trade-offs, and integrate the DG412CY+T confidently into an existing 16-pin SOIC design.
Alternatif penggantian untuk DG412CY+T — paket yang sama, pin-pada-pin kompatibel. Bagian paket yang berbeda memerlukan kerja ulang PCB diabaikan.
DG412CY+
✅ Drop-In📋 Alternatif referensi (tidak dalam katalog)
DG412DY+
✅ Drop-InKontak untuk harga
Lihat Datasheet →DG412DYZ
✅ Drop-In📋 Alternatif referensi (tidak dalam katalog)
DG412DY-T2-E3
✅ Drop-In📋 Alternatif referensi (tidak dalam katalog)
DG412DY-T1-E3
✅ Drop-In📋 Alternatif referensi (tidak dalam katalog)
DG412CY+T Rating Maksimal & Karakteristik Listrik
| Product Type | Quad SPST analog switch |
| Number of Switches | 4 circuits |
| Switch Configuration | 4 x SPST |
| Number of Channels | 1 channel |
| Signal-to-Noise Ratio | 1:1 |
| Maximum On-Resistance | 45 Ω |
| On-Resistance Matching | 3 Ω maximum |
| On-Resistance Flatness | 4 Ω maximum |
| Process Technology | CMOS |
| Conduction Direction | Bidirectional |
| ESD Tolerance | 2000 V minimum per Method 3015.7 |
| Tegangan Pemuat | 22 V to 25 V |
| Paket | 16-pin SOIC (PDSO16) |
| Package Body Width | 0.15 inch |
| Tipe Mounting | Surface mount |
| Status RoHS | Compliant |
| Production Status | Production |
| Charge Injection | Low; exact value not specified |
| Power Consumption | Low; exact value not specified |
DG412CY+T 0.15 inch Diamant Konfigurasi Panduan
Konfigurasi pin untuk DG412CY+T (0.15 inch pakai pakai). Penomoran pin, fungsi, dan diagram koneksi ditetapkan dalam datasheet produsen. Lihatnya untuk footprint dan pedoman perpindahan paruh.
Tidak ada data diatribut pin yang tersedia untuk DG412CY+T.
Lihat ke: datasheet produk untuk konfigurasi pin penuh.
Aplikasi Umum
DG412CY+T cocok untuk 6 aplikasis: Automated Test Equipment Signal Routing, Data Acquisition and Sensor Selection, Battery and Power-System Routing, Peripheral and Signal-Path Selection, Precision Control and Instrumentation, Sample-and-Hold Isolation.
Automated Test Equipment Signal Routing
The DG412CY+T is suitable for automated test equipment that requires several independently controlled analog connections. Each of its four SPST channels can route a DUT, instrument, or fixture signal under digital control, while the 45 Ω maximum on-resistance is acceptable for many low-power measurement paths. The 3 Ω maximum on-resistance matching helps maintain channel-to-channel consistency in multiswitch systems. Bidirectional conduction also simplifies fixture routing because the signal can travel through the closed switch in either direction. Confirm charge injection, off-state leakage, bandwidth, and control-logic polarity against the specific measurement bandwidth before final qualification.
Direkomendasikan
Data Acquisition and Sensor Selection
The four independent switches in the DG412CY+T can select sensor outputs, excitation paths, or amplifier inputs within a data-acquisition system. Independent control permits different channels to be connected at different times, reducing the number of external multiplexing components. A maximum on-resistance of 45 Ω should be included in the sensor-source impedance calculation, particularly for high-impedance transducers, because it can influence attenuation and input settling. Low on-resistance matching supports repeatable channel behavior. Validate the complete acquisition chain for switch charge injection, leakage, off-state rejection, and settling time at the highest conversion rate used by the instrument.
Direkomendasikan
Battery and Power-System Routing
The DG412CY+T can route low-current power or control paths among four independent SPST channels. Its maximum on-resistance of 45 Ω makes it more appropriate for low-current routing and control than for high-current power conversion or load sharing, and the design must account for conduction loss in the closed state. Bidirectional operation supports source selection between two power domains or isolation of an external subsystem. Use the manufacturer’s absolute maximum and electrical characteristics to confirm supply and signal-terminal limits, then verify the transistor or power path that drives each control input during startup and shutdown.
Direkomendasikan
Peripheral and Signal-Path Selection
A quad SPST arrangement is useful when a controller must connect one peripheral to one of several interchangeable signal sources without changing the board layout. The DG412CY+T provides four separately controlled switches in a 16-pin SOIC package, reducing the logic overhead associated with multiplexed routing where only one channel is active at a time. Bidirectional conduction supports peripheral-to-host and host-to-peripheral traffic. Because the switch has up to 45 Ω on-resistance and introduces finite switching transients, account for those effects in high-impedance inputs, communication links, and timing-sensitive control loops.
Direkomendasikan
Precision Control and Instrumentation
The DG412CY+T can isolate or connect control lines in laboratory and industrial instrumentation where four channels must be switched independently. Its specified on-resistance matching of 3 Ω maximum and flatness of 4 Ω maximum support predictable behavior across the switched signal range. The 45 Ω maximum on-resistance must be included in amplifier-input impedance and loop-gain calculations, while low charge injection is advantageous for high-impedance nodes. Confirm the actual signal amplitude, bandwidth, leakage, and control timing against the manufacturer’s characterization tables before using the switch in precision feedback or measurement paths.
Direkomendasikan
Sample-and-Hold Isolation
The DG412CY+T can connect or disconnect a sampled signal from a hold capacitor or measurement amplifier, helping reduce unwanted interaction between acquisition stages. The low-charge-injection characteristic supports transient control, although the exact switching transient must be checked at the operating supply and control voltage. Because the maximum on-resistance is 45 Ω, capacitor charging and settling behavior depend on the source resistance, capacitor value, and amplifier input impedance. Use the datasheet timing and switching characteristics to select the control timing and verify droop, acquisition time, and leakage over the intended temperature range.
Direkomendasikan
Ringkasan Produk Direkomendasikan
Data referensi engineering untuk DG412CY+T — pembandingan, panduan desain, dan informasi konformitas.
Panduan Pemilihan
Pembandingan dengan Alternatif
| Parameter Umum | Produk Ini | DG412CY+ | DG412DY+ | DG412DYZ | DG412DY-T2-E3 | DG412DY-T1-E3 |
|---|---|---|---|---|---|---|
| Package | SOIC-16 | SOIC-16 | SOIC-16 | SOIC-16 | SOIC-16 | SOIC-16 |
| Brand | Analog Devices | Analog Devices | Analog Devices | Renesas Electronics | Vishay Intertechnology | Vishay Intertechnology |
| Switch Configuration | 4 x SPST | 4 x SPST | 4 x SPST | 4-circuit SPST | 4 x SPST | 4 x SPST |
| Maximum On-Resistance | 45 Ω | 45 Ω class | 35 Ω | 35 Ω | 35 Ω | 35 Ω |
Diferensiator Kunci
- Improved on-resistance matching (vsDG412DY+)
- Four independent bidirectional SPST channels (vsDG412DYZ)
- Production-family configuration with specified RoHS compliance (vsDG412DY-T2-E3)
Catatan Desain
Include the maximum 45 Ω on-resistance in source-impedance and settling calculations. When driving a capacitive load, the switch resistance interacts with the capacitor ESR and the amplifier input impedance, increasing acquisition time. For high-impedance nodes, also evaluate charge injection and off-state leakage from the DG412 characteristic tables at the actual control voltage and supply condition.
Place the DG412CY+T close to the switched analog nodes and keep each IN-to-OUT trace short. Route the four control inputs away from sensitive analog conductors, and provide a nearby ground return to reduce pickup during switching transitions. Confirm the pin numbering against the manufacturer's 16-pin SOIC pin-description table before assigning the two terminal pairs of each SPST channel.
Design the control signals so the switch cannot enter an unintended state during power-up or reset. Because four independent channels can route power as well as signals, use pull-down or pull-up resistors where a defined off state is safety-critical. Account for the closed-switch voltage drop and 45 Ω maximum resistance when estimating conduction loss with actual current.
Do not treat a same-family SOIC-16 replacement as automatically approved for every application. Review control polarity, temperature grade, absolute maximum terminal voltage, bandwidth, leakage, charge injection, and production status for the exact suffix. The Renesas and Vishay alternatives list a 35 Ω maximum on-resistance, which is 22% below the DG412CY+T value and may alter source impedance and settling behavior.
Informasi Konformitas
RoHS compliance is explicitly identified for the device. No automotive qualification, REACH declaration, lead-free statement, halogen-free classification, or conflict-minerals report was identified.