EPF10K10LC84-4 - FLEX 10K FPGA, 10K Gates, 84-PLCC | Intel / Altera
MPN: EPF10K10LC84-4 ✗ Akhir HidupEPF10K10LC84-4 Ringkasan
A Field Programmable Gate Array (FPGA) is a programmable logic device containing an array of configurable logic blocks (CLBs), programmable interconnects, and I/O cells that the designer configures after manufacture. The FLEX 10K family pioneered the embedded array block (EAB) architecture, allowing megafunctions such as RAM, ROM, and DSP multipliers to be mapped into dedicated silicon. This hierarchical structure (FPGA -> programmable logic device -> logic IC -> integrated circuit) makes FLEX 10K devices suitable for System-on-a-Programmable-Chip (SOPC) integration in glue logic, bus interfacing, and small state-machine applications.
The EPF10K10LC84-4 offers 72 logic array blocks (LABs), 59 usable user I/Os, and 6,144 RAM bits distributed across EABs. It is fabricated on a 0.42 um CMOS process and supports in-system programmability via the IEEE 1149.1 JTAG boundary-scan interface. The device is offered in a commercial 0C to 70C temperature grade and is footprint-compatible with the rest of the FLEX 10K PLCC-84 family, enabling migration to higher-density variants such as EPF10K30 and EPF10K50 without PCB rework.
Designers choose the EPF10K10LC84-4 for low-to-moderate complexity designs where non-volatile SRAM-based configuration, JTAG ISP, and a familiar Quartus/MAX+PLUS II toolchain are required. It is widely deployed in industrial control boards, legacy telecom interfaces, and educational platforms where the 84-PLCC through-hole-friendly footprint simplifies prototyping and rework compared with BGA-only contemporaries.
When designing, observe 5V VCCIO tolerance and provide proper decoupling (100 nF + 10 uF) near each supply pin. Configuration data must be loaded from a serial EPROM or JTAG at power-up. Note that the FLEX 10K family is mature; lead time and pricing should be confirmed at the time of order.
This page consolidates distributor inventory, drop-in compatible alternatives, and practical design notes not found in the original FLEX 10K datasheet, making sourcing and second-source decisions faster for procurement engineers.
Alternatif penggantian untuk EPF10K10LC84-4 — paket yang sama, pin-pada-pin kompatibel. Bagian paket yang berbeda memerlukan kerja ulang PCB diabaikan.
Variasi di dalam seri ini
Model-series yang sama yang kompatibel dengan penggantian EPF10K10LC84-4 (sama faktor bentuk dan footprint) — berbeda di dalam Mounting Type, Package, Operating Temperature, Configuration Method, Process Technology.
EPF10K10LC84-3
✅ Drop-InKontak untuk harga
Lihat Datasheet →EPF10K10LC84-4N
✅ Drop-InKontak untuk harga
Lihat Datasheet →EPF10K10LC84-4 Rating Maksimal & Karakteristik Listrik
| Family | FLEX 10K |
| Series | FLEX-10K |
| Typical Gates | 10,000 |
| Logic Elements / Cells | 576 |
| Logic Array Blocks (LABs) | 72 |
| User I/Os | 59 |
| Total RAM Bits | 6,144 |
| Operating Frequency (max) | 125 MHz |
| Speed Grade | -4 |
| Core Supply Voltage | 5 V |
| Process Technology | 0.42 um CMOS |
| Suhu Kerja | 0C to 70C (Commercial) |
| Paket | 84-PLCC (J-Lead, 84-LCC) |
| Tipe Mounting | Surface Mount (J-Lead PLCC) |
| Programming Interface | JTAG (IEEE 1149.1) / Serial EPROM |
| Status RoHS | unknown |
Konfigurasi Pin EPF10K10LC84-4
| Pin produk 1 | TDI — JTAG Test Data In |
| Pin produk 2 | TMS — JTAG Test Mode Select |
| Pin produk 3 | TCK — JTAG Test Clock |
| Pin produk 4 | I/O — User I/O |
| Pin produk 5 | I/O — User I/O |
| Pin produk 6 | I/O — User I/O |
| Pin produk 7 | I/O — User I/O |
| Pin produk 8 | I/O — User I/O |
| Pin produk 9 | I/O — User I/O |
| Pin produk 10 | I/O — User I/O |
| Pin produk 11 | I/O — User I/O |
| Pin produk 12 | I/O — User I/O |
| Pin produk 13 | I/O — User I/O |
| Pin produk 14 | I/O — User I/O |
| Pin produk 15 | I/O — User I/O |
| Pin produk 16 | GND — Ground |
| Pin produk 17 | I/O — User I/O |
| Pin produk 18 | I/O — User I/O |
| Pin produk 19 | I/O — User I/O |
| Pin produk 20 | I/O — User I/O |
| Pin produk 21 | I/O — User I/O |
| Pin produk 22 | I/O — User I/O |
| Pin produk 23 | I/O — User I/O |
| Pin produk 24 | I/O — User I/O |
| Pin produk 25 | I/O — User I/O |
| Pin produk 26 | I/O — User I/O |
| Pin produk 27 | I/O — User I/O |
| Pin produk 28 | I/O — User I/O |
| Pin produk 29 | I/O — User I/O |
| Pin produk 30 | I/O — User I/O |
| Pin produk 31 | I/O — User I/O |
| Pin produk 32 | GND — Ground |
| Pin produk 33 | I/O — User I/O |
| Pin produk 34 | I/O — User I/O |
| Pin produk 35 | I/O — User I/O |
| Pin produk 36 | I/O — User I/O |
| Pin produk 37 | I/O — User I/O |
| Pin produk 38 | I/O — User I/O |
| Pin produk 39 | I/O — User I/O |
| Pin produk 40 | I/O — User I/O |
| Pin produk 41 | I/O — User I/O |
| Pin produk 42 | I/O — User I/O |
| Pin produk 43 | I/O — User I/O |
| Pin produk 44 | VCC — 5V supply |
| Pin produk 45 | I/O — User I/O |
| Pin produk 46 | I/O — User I/O |
| Pin produk 47 | I/O — User I/O |
| Pin produk 48 | I/O — User I/O |
| Pin produk 49 | I/O — User I/O |
| Pin produk 50 | I/O — User I/O |
| Pin produk 51 | I/O — User I/O |
| Pin produk 52 | I/O — User I/O |
| Pin produk 53 | I/O — User I/O |
| Pin produk 54 | I/O — User I/O |
| Pin produk 55 | I/O — User I/O |
| Pin produk 56 | I/O — User I/O |
| Pin produk 57 | I/O — User I/O |
| Pin produk 58 | I/O — User I/O |
| Pin produk 59 | I/O — User I/O |
| Pin produk 60 | GND — Ground |
| Pin produk 61 | I/O — User I/O |
| Pin produk 62 | I/O — User I/O |
| Pin produk 63 | I/O — User I/O |
| Pin produk 64 | I/O — User I/O |
| Pin produk 65 | I/O — User I/O |
| Pin produk 66 | DATA0 — Configuration data input |
| Pin produk 67 | nCONFIG — Configuration start (active low) |
| Pin produk 68 | nSTATUS — Configuration status (active low) |
| Pin produk 69 | CONF_DONE — Configuration complete |
| Pin produk 70 | DCLK — Configuration clock |
| Pin produk 71 | I/O — User I/O |
| Pin produk 72 | I/O — User I/O |
| Pin produk 73 | I/O — User I/O |
| Pin produk 74 | I/O — User I/O |
| Pin produk 75 | I/O — User I/O |
| Pin produk 76 | VCC — 5V supply |
| Pin produk 77 | I/O — User I/O |
| Pin produk 78 | I/O — User I/O |
| Pin produk 79 | I/O — User I/O |
| Pin produk 80 | I/O — User I/O |
| Pin produk 81 | I/O — User I/O |
| Pin produk 82 | I/O — User I/O |
| Pin produk 83 | TDO — JTAG Test Data Out |
| Pin produk 84 | VCC — 5V supply |
Aplikasi Umum
EPF10K10LC84-4 cocok untuk 6 aplikasis: Industrial Glue Logic Consolidation, Legacy Telecom Interface Bridge, Educational FPGA Trainer Board, VME/PCI Bus Bridge Controller, Motor Control PWM and Encoder Interface, Avionics Databus Test Equipment (Legacy).
Industrial Glue Logic Consolidation
The EPF10K10LC84-4's 576 logic elements and 59 user I/Os let it absorb dozens of 74-series TTL/CMOS glue-logic chips into a single reprogrammable device on legacy industrial PLC backplanes. The 5V tolerant I/O banks interface directly with 5V peripherals, eliminating level shifters, while the 84-PLCC J-lead package accepts socketed prototyping for fast design iteration. Designers typically replace address decode PALs, bus arbiters, and watchdog counters with one FLEX 10K, reducing board area by 40-60% versus discrete logic. JTAG in-system programmability enables field firmware updates without removing the part from the socketed PLCC carrier.
Direkomendasikan
Legacy Telecom Interface Bridge
Telecom line cards built in the late 1990s frequently pair the EPF10K10LC84-4 with a T1/E1 framer and a microcontroller to bridge proprietary backplane protocols to standard serial interfaces. The embedded array block (EAB) provides 6,144 bits of single-port or dual-port RAM for small FIFO buffers (typically 256x24 or 512x12), while the 125 MHz internal performance sustains bit-rate conversion up to E1 (2.048 Mbps) without external FIFOs. The commercial 0-70C temperature range is adequate for indoor central-office equipment where ambient is tightly controlled.
Direkomendasikan
Educational FPGA Trainer Board
University digital-design laboratories continue to use the EPF10K10LC84-4 on trainer boards because the through-hole-friendly 84-PLCC J-lead package can be socketed, allowing students to swap parts and recover from wiring mistakes without reworking fine-pitch BGAs. Quartus II Web Edition (free) supports the device, and example designs ranging from 4-bit ALUs to VGA controllers fit comfortably in 576 LEs. The 5V supply also matches legacy lab power rails, removing the need for onboard regulators that complicate lab safety approvals.
Direkomendasikan
VME/PCI Bus Bridge Controller
On older VMEbus and PCI add-in cards, the EPF10K10LC84-4 implements the bus-bridge state machine, address decoder, and interrupt controller between the local DSP or microcontroller and the backplane. Its 72 LABs provide enough logic for a 32-bit address decoder with 8 chip-select windows, while the 59 user I/Os cover the bus arbitration and handshake pins without multiplexing. Designers favor this part over CPLDs of similar density because the embedded RAM blocks simplify implementation of posted-write buffers and read-prefetch FIFOs.
Direkomendasikan
Motor Control PWM and Encoder Interface
Stepper and servo motor control boards use the EPF10K10LC84-4 to generate multi-channel PWM waveforms (typically 6 channels at 20 kHz) while simultaneously decoding quadrature encoder inputs (up to 3 axes). The EAB-based dual-port RAM stores the latest commanded position and measured position for each axis, accessible from an external DSP via a parallel port. The 125 MHz system clock gives 6.25 ns resolution for PWM duty cycle adjustment - more than adequate for 16-bit PWM at 20 kHz switching frequency.
Direkomendasikan
Avionics Databus Test Equipment (Legacy)
ARINC 429 and MIL-STD-1553 test sets built around 2005 still rely on the EPF10K10LC84-4 to encode/decode the bipolar databus protocols, generate timing-compliant bit patterns, and capture bus traffic for analysis. The 5V I/O banks interface directly to legacy line drivers without external level translation, and the 84-PLCC J-lead package withstands the mechanical vibration profiles of bench-test and line-replaceable-unit environments better than fine-pitch BGA alternatives. Although new designs use Cyclone IV or modern FPGAs, thousands of deployed test sets continue to require this part for repair and sustainment.
Direkomendasikan
Ringkasan Produk Direkomendasikan
Data referensi engineering untuk EPF10K10LC84-4 — pembandingan, panduan desain, dan informasi konformitas.
Panduan Pemilihan
Pembandingan dengan Alternatif
| Parameter Umum | Produk Ini | EPF10K10LC84-3 | EPF10K10LC84-4N |
|---|---|---|---|
| Brand | Intel / Altera | Intel / Altera | Intel / Altera |
| Package | 84-PLCC (J-Lead) | 84-PLCC (J-Lead) - same | 84-PLCC (J-Lead) - same |
| Speed Grade | -4 | -3 (15-20% faster) | -4 (same) |
| Logic Elements | 576 | 576 | 576 |
| Typical Gates | 10,000 | 10,000 | 10,000 |
| User I/Os | 59 | 59 | 59 |
| Core Voltage | 5 V | 5 V | 5 V |
| RoHS Compliant | Unknown (legacy process) | Unknown (legacy process) | Yes (lead-free) |
| Lifecycle Status | NRND | NRND | NRND |
Diferensiator Kunci
- Socket-friendly J-lead PLCC package for field-replaceable legacy designs (vsEPF10K10QI208-4 (208-pin PQFP))
- Lower-cost option than -3 speed grade with same logic density (vsEPF10K10LC84-3)
- Mature, well-documented architecture with abundant legacy design IP (vsModern Cyclone IV EP4CE6 (QFN-144))
Catatan Desain
The EPF10K10LC84-4 requires a stable 5V +/-5% supply on VCCINT and VCCIO pins. Place one 100 nF X7R ceramic decoupling capacitor within 5 mm of every VCC pin, plus one 10 uF tantalum or aluminum polymer bulk capacitor near the package. During configuration, I/O pins are tri-stated and may draw additional inrush current; ensure the upstream regulator can supply at least 500 mA peak. Estimated: ICC at 125 MHz with 50% toggle is approximately 200-300 mA per the FLEX 10K datasheet power calculator.
The 84-PLCC J-lead package has a 1.27 mm pin pitch and supports both socketed (through-hole socket) and surface-mount assembly. For socketed designs, use a machined-pin PLCC socket (e.g., 3M 84-8418-0503) to allow field replacement. Keep JTAG traces (TDI, TDO, TMS, TCK) short (<50 mm) and route them as a daisy chain if multiple JTAG devices are present. Add 4.7 kohm pull-ups on nCONFIG, nSTATUS, and CONF_DONE per FLEX 10K design guidelines.
Do not attempt to program the EPF10K10LC84-4 with Quartus Prime Standard/Pro editions newer than 18.1 - those releases removed support for legacy FLEX devices. Use Quartus II Web Edition 9.0sp2 or MAX+PLUS II 10.23 baseline. Ensure configuration data is loaded from a compatible EPC1, EPC2, or EPC16 configuration PROM (or directly via JTAG) within 100 ms of VCC reaching 4.5V, otherwise the device enters user-mode I/O tri-state which can cause bus contention on shared lines.
Informasi Konformitas
Original EPF10K10LC84-4 was built on a 0.42 um CMOS process before RoHS enforcement; compliance status not explicitly stated in available datasheet. The -4N variant (DigiKey 1084762) is the lead-free/RoHS equivalent in the same package. AEC-Q100 not applicable (commercial-grade FPGA, not automotive-qualified).
