FT812Q-T - EVE2 Video Controller IC, SPI, 56-QFN | Bridgetek
MPN: FT812Q-T ✓ AktifFT812Q-T Ringkasan
An Embedded Video Engine (EVE) is a system-on-chip graphics controller that offloads rendering, widget composition, audio playback, and touch scanning from the host MCU. EVE controllers occupy a unique position in the embedded display hierarchy - sitting between simple character LCDs and full graphics SoCs - delivering high-quality HMIs without requiring a high-performance host processor or external frame buffer memory.
Key features of the FT812Q-T include a built-in graphics engine supporting jpeg decoding and ASTC texture compression, a 1 MByte graphics RAM, integrated PWM audio output, and a resistive touch screen controller with hardware scanning. It supports display resolutions up to 1024x768 (HVGA+) via its programmable 24-bit RGB interface, with display sizes configurable up to 512x512 for the FT81x family. The device operates from a single 3.3V supply (2.97V to 3.63V) and is specified for the -40C to +85C industrial temperature range.
From an architecture standpoint, the FT812Q-T combines an embedded graphics accelerator, a configurable display controller, audio DAC with class-D amplifier interface, and a touch engine into a single BGA-equivalent VQFN package. The 56-QFN-EP exposed pad provides thermal relief and a low-impedance ground return. Communication occurs through SPI at speeds up to 100 Mbps, allowing the host MCU to issue high-level display-list commands rather than pixel-by-pixel updates, dramatically reducing MCU firmware complexity and SPI bus traffic.
Typical applications include point-of-sale terminals, industrial control panels, medical device HMIs, security systems, teleconferencing equipment, smart home control panels, and portable instrumentation displays. The wide operating voltage and temperature ranges suit industrial, medical, and security applications requiring reliable operation in harsh environments.
When designing with the FT812Q-T, pay attention to PCB layout: route SPI traces as short 50-ohm impedance-controlled lines, place the 0.1uF decoupling capacitor within 3mm of the supply pin, and solder the exposed pad to a continuous ground plane for thermal dissipation and low-noise digital return paths. The EVE2 command protocol requires the host MCU firmware library from Bridgetek for proper display-list construction.
This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet - including a 5-alternative comparison matrix from Bridgetek's FT81x family and cross-brand VQFN-56 competitors, plus an honest application-by-application fit analysis.
Alternatif penggantian untuk FT812Q-T — paket yang sama, pin-pada-pin kompatibel. Bagian paket yang berbeda memerlukan kerja ulang PCB diabaikan.
Variasi di dalam seri ini
Model-series yang sama yang kompatibel dengan penggantian FT812Q-T (sama faktor bentuk dan footprint) — berbeda di dalam Host Interface, Operating Temperature, Package, Touch Controller.
FT810Q-T
✅ Drop-In📋 Alternatif referensi (tidak dalam katalog)
FT811Q-T
✅ Drop-In📋 Alternatif referensi (tidak dalam katalog)
FT813Q-T
✅ Drop-In📋 Alternatif referensi (tidak dalam katalog)
FT812Q-T Spesifikasi
| Product Type | Embedded Video Engine (EVE2) Controller |
| Family | FT81x (EVE2) |
| Host Interface | SPI (up to 100 Mbps) |
| Display Interface | 24-bit RGB parallel |
| Maximum Resolution | 1024 x 768 (HVGA+) |
| Touch Controller | Resistive touch (built-in hardware scanning) |
| Graphics RAM | 1 MByte |
| Audio Output | PWM audio output / Class-D amplifier interface |
| Tegangan Pemuat | 2.97 V to 3.63 V (3.3 V typical) |
| I/O Voltage | 1.8 V to 3.3 V |
| Suhu Kerja | -40 C to +85 C |
| Paket | VQFN-56-EP (8x8 mm) |
| Package Type | VQFN-EP (Very-thin QFN with Exposed Pad) |
| Tipe Mounting | Surface Mount |
| Status RoHS | Compliant |
| Level MSL | 3 (168 hours) |
Konfigurasi Pin FT812Q-T
| Pin produk 1 | SCK — SPI clock input from host MCU |
| Pin produk 2 | MISO — SPI master-in-slave-out (data to host) |
| Pin produk 3 | MOSI — SPI master-out-slave-in (data from host) |
| Pin produk 4 | CS — SPI chip-select (active low) |
| Pin produk 5 | INT — Interrupt output to host |
| Pin produk 6 | PD — Power-down input |
| Pin produk 7 | RST — Hardware reset (active low) |
| Pin produk 8 | VCC — 3.3V core supply |
| Pin produk 9 | GND — Ground |
| Pin produk 10 | VCCIO — I/O supply voltage (1.8V-3.3V) |
| Pin produk 11 | GPIO0 — General-purpose I/O |
| Pin produk 12 | GPIO1 — General-purpose I/O |
| Pin produk 13 | GPIO2 — General-purpose I/O |
| Pin produk 14 | GPIO3 — General-purpose I/O / WAKE |
| Pin produk 15 | AUDIO — PWM audio output to amplifier |
| Pin produk 16 | X+ — Resistive touch X+ input |
| Pin produk 17 | Y+ — Resistive touch Y+ input |
| Pin produk 18 | X- — Resistive touch X- input |
| Pin produk 19 | Y- — Resistive touch Y- input |
| Pin produk 20 | DISP — Display enable / backlight control |
| Pin produk 21 | HSYNC — Horizontal sync to TFT display |
| Pin produk 22 | VSYNC — Vertical sync to TFT display |
| Pin produk 23 | DE — Data enable to TFT display |
| Pin produk 24 | PCLK — Pixel clock to TFT display |
| Pin produk 25 | RGB0 — RGB data bit 0 (blue LSB) |
| Pin produk 26 | RGB1 — RGB data bit 1 |
| Pin produk 27 | RGB2 — RGB data bit 2 |
| Pin produk 28 | RGB3 — RGB data bit 3 |
| Pin produk 29 | RGB4 — RGB data bit 4 |
| Pin produk 30 | RGB5 — RGB data bit 5 |
| Pin produk 31 | RGB6 — RGB data bit 6 |
| Pin produk 32 | RGB7 — RGB data bit 7 (blue MSB) |
| Pin produk 33 | GND — Ground |
| Pin produk 34 | RGB8 — RGB data bit 8 (green LSB) |
| Pin produk 35 | RGB9 — RGB data bit 9 |
| Pin produk 36 | RGB10 — RGB data bit 10 |
| Pin produk 37 | RGB11 — RGB data bit 11 |
| Pin produk 38 | RGB12 — RGB data bit 12 |
| Pin produk 39 | RGB13 — RGB data bit 13 |
| Pin produk 40 | RGB14 — RGB data bit 14 |
| Pin produk 41 | RGB15 — RGB data bit 15 (green MSB) |
| Pin produk 42 | GND — Ground |
| Pin produk 43 | RGB16 — RGB data bit 16 (red LSB) |
| Pin produk 44 | RGB17 — RGB data bit 17 |
| Pin produk 45 | RGB18 — RGB data bit 18 |
| Pin produk 46 | RGB19 — RGB data bit 19 |
| Pin produk 47 | RGB20 — RGB data bit 20 |
| Pin produk 48 | RGB21 — RGB data bit 21 |
| Pin produk 49 | RGB22 — RGB data bit 22 |
| Pin produk 50 | RGB23 — RGB data bit 23 (red MSB) |
| Pin produk 51 | NC — Not connected (per datasheet) |
| Pin produk 52 | NC — Not connected (per datasheet) |
| Pin produk 53 | NC — Not connected (per datasheet) |
| Pin produk 54 | TEST — Factory test pin (leave floating per datasheet) |
| Pin produk 55 | GND — Ground |
| Pin produk 56 | EP — Exposed pad - thermal/ground connection (must be soldered) |
Aplikasi Umum
FT812Q-T cocok untuk 7 aplikasis: Point-of-Sale Terminals, Industrial Control Panels, Medical Device HMIs, Security Systems, Teleconferencing Equipment, Smart Home Control Panels, Portable Instrumentation Displays.
Point-of-Sale Terminals
The FT812Q-T's 1024x768 max resolution, 24-bit RGB interface, and 1 MByte internal graphics RAM make it a strong fit for color TFT displays in POS terminals. Per the FT81x datasheet, the integrated PWM audio output drives speaker buzzers for transaction confirmation tones without an external audio DAC. The 3.3V supply and -40C to +85C industrial range suit retail back-office and kitchen-display environments. Its resistive touch controller eliminates the need for a separate touch IC, reducing BOM cost in price-sensitive POS designs. Recommended companion MPNs: STM32F407VG (host MCU), ER-TFT050-2 (5-inch display).
Direkomendasikan
Industrial Control Panels
Industrial HMIs benefit from the FT812Q-T's wide 2.97V-3.63V supply tolerance and -40C to +85C operating range. The 24-bit RGB bus drives full-color TFT panels used for machine status displays, while the built-in graphics engine renders gauges, trends, and alarms without taxing the host MCU. Per the Bridgetek datasheet, the resistive touch interface works with gloved-finger operation common in factory environments. The 56-QFN-EP package is suitable for reflow soldering on standard FR-4 industrial PCBs. Recommended companion MPNs: STM32H743ZI (high-performance host MCU), FT232HL-REEL (USB-SPI bridge for firmware updates).
Direkomendasikan
Medical Device HMIs
Medical equipment displays - infusion pumps, patient monitors, diagnostic analyzers - use the FT812Q-T for its high-resolution graphics and reliable resistive touch sensing. Per the Bridgetek FT81x documentation, the integrated audio engine supports alarm-tone generation critical for patient-safety notifications. The 3.3V single-supply operation simplifies medical device power trees, and the 56-QFN-EP footprint suits compact handheld form factors. Designers must still verify IEC 60601-1 EMI/EMC compliance at the system level; the FT812Q-T itself is not a medical-grade qualified component. Recommended companion MPNs: MSP432P401R (low-power host MCU), CY8C4127AXI-S443 (PSoC auxiliary touch UI).
Direkomendasikan
Security Systems
Security keypads, access-control panels, and alarm-system displays use the FT812Q-T for its TFT driving capability and integrated touch sensing. Per the Bridgetek product page, the FT81x family is widely adopted in security HMIs for icon-based status displays. The hardware JPEG decoder accelerates camera-preview overlays, and the audio PWM output drives sirens or voice prompts. The -40C to +85C industrial temperature range supports outdoor panel installations in unconditioned enclosures. Recommended companion MPNs: STM32F407VG (host MCU), DRV110APWR (siren driver IC).
Direkomendasikan
Teleconferencing Equipment
Conference-room touch panels and meeting-room controllers use the FT812Q-T to drive 7-to-10-inch color TFT displays showing room calendars, room status, and meeting controls. The 24-bit RGB interface supports high-quality graphics with smooth gradients for brand-aligned UI. Per the Bridgetek FT81x documentation, the integrated audio engine handles touch-click feedback tones and meeting-start chimes. The 56-QFN-EP package is small enough for in-wall touch panel enclosures. Recommended companion MPNs: ESP32-WROOM-32 (Wi-Fi host MCU for calendar sync), FT232HL-REEL (USB programming/debug bridge).
Direkomendasikan
Smart Home Control Panels
Wall-mounted smart-home touch panels use the FT812Q-T for their high-resolution displays and integrated touch control. Per the Bridgetek product literature, the FT81x family enables premium UI design with smooth animations and icon-rich screens. The 3.3V single supply simplifies mains-powered wall-panel designs with AC-DC converters. The 1 MByte internal graphics RAM stores UI assets without external flash, reducing BOM cost for consumer products. Recommended companion MPNs: STM32H743ZI (host MCU), DRV8873HPWPR (relay/load driver).
Direkomendasikan
Portable Instrumentation Displays
Handheld oscilloscopes, multimeters, and portable test equipment use the FT812Q-T for their color TFT displays and touch-driven UI. Per the Bridgetek FT81x datasheet, the device's low-power design and 3.3V supply suit battery-powered instruments. The built-in graphics engine renders waveforms, FFT plots, and measurement overlays efficiently, offloading the host MCU. The industrial temperature range supports field-use conditions. Recommended companion MPNs: STM32F407VG (host MCU), ADS131A04 (precision ADC companion).
Direkomendasikan
Ringkasan Produk Direkomendasikan
Data referensi engineering untuk FT812Q-T — pembandingan, panduan desain, dan informasi konformitas.
Panduan Pemilihan
Pembandingan dengan Alternatif
| Parameter Umum | Produk Ini | FT810Q-T | FT811Q-T | FT813Q-T |
|---|---|---|---|---|
| Brand | Bridgetek | Bridgetek | Bridgetek | Bridgetek |
| Package | VQFN-56-EP (8x8 mm) | VQFN-56-EP (8x8 mm) - same | VQFN-56-EP (8x8 mm) - same | VQFN-56-EP (8x8 mm) - same |
| Touch Type | Resistive | Capacitive | Capacitive | Capacitive |
| Max Display Resolution | 512 x 512 (FT812) | 512 x 512 | 512 x 512 | 1024 x 768 (HVGA+) |
| Host Interface | SPI up to 100 Mbps | SPI up to 100 Mbps | SPI up to 100 Mbps | SPI up to 100 Mbps |
| Display Interface | 24-bit RGB parallel | 24-bit RGB parallel | 24-bit RGB parallel | 24-bit RGB parallel |
| Graphics RAM | 1 MByte | 1 MByte | 1 MByte | 1 MByte |
| Audio Output | PWM / Class-D interface | PWM / Class-D interface | PWM / Class-D interface | PWM / Class-D interface |
| Supply Voltage | 2.97V - 3.63V | 2.97V - 3.63V | 2.97V - 3.63V | 2.97V - 3.63V |
| Operating Temperature | -40C to +85C | -40C to +85C | -40C to +85C | -40C to +85C |
Diferensiator Kunci
- Integrated graphics engine eliminates host MCU pixel processing (vsFT810Q-T)
- Resistive touch variant suited for industrial glove operation (vsFT811Q-T)
- Higher display resolution than FT810/FT811 (vsFT813Q-T)
Catatan Desain
Route the SPI bus (SCK, MISO, MOSI, CS) as short matched-length traces in a 50-ohm impedance-controlled region. Place a 0.1uF ceramic decoupling capacitor within 3mm of the VCC pin and a 1uF bulk capacitor within 10mm. The exposed pad (EP) MUST be soldered to a continuous ground plane with at least 4 thermal vias for heat dissipation and low-impedance digital return paths. Use a 4-layer PCB with dedicated ground and power planes to minimize EMI on the parallel RGB bus, which switches at pixel-clock rates up to 50 MHz.
The FT812Q-T requires a clean 3.3V supply within 2.97V-3.63V. Estimated current draw is 60-80 mA during active graphics rendering plus additional current for RGB bus switching. Add a ferrite bead in series with the 3.3V supply to isolate digital switching noise from sensitive analog circuitry in the host system. Place a 10uF tantalum or ceramic bulk capacitor near the IC, in addition to the 0.1uF high-frequency decoupling, to handle transient current demands during display refresh.
Do not omit the host MCU firmware library from Bridgetek - the EVE2 command protocol requires the official FT81x library for proper display-list construction. The reset pin (RST) requires a 10k pull-up to VCC and a 1nF capacitor to ground for proper power-on-reset behavior per the datasheet. The TEST pin (pin 54) MUST be left floating - do not connect to ground or VCC. Touch panel calibration values must be stored in non-volatile memory on the host MCU side; the FT812Q-T does not retain calibration through power cycles.
The 24-bit RGB bus and pixel clock can generate significant EMI above 30 MHz. Use controlled-impedance routing (typically 50 ohms single-ended) with series termination resistors (22-33 ohms) on the pixel clock and high-order RGB lines if the display is more than 50mm away. Keep the RGB bus away from analog-sensitive traces. Consider adding a common-mode choke on the display flex cable for EMI compliance in industrial applications requiring CE/FCC certification.
Informasi Konformitas
RoHS compliant per Bridgetek product page and JLCPCB listing. Not AEC-Q100 qualified - the FT81x family targets industrial/consumer HMI, not automotive. Halogen-free status not explicitly stated in the verified data - set to 'unknown' per data authenticity rules.
