Texas Instruments

LM339APW - Quad Differential Comparator, TSSOP-14 | Texas Instruments

MPN: LM339APW ✓ Aktif
30 V Vdss 200 uA Id 14-TSSOP (PW) Package
MOQ: 1 |

LM339APW Ringkasan

The Texas Instruments LM339APW is a quad differential comparator integrating four independent voltage comparators with open-collector outputs in a 14-pin TSSOP (PW) package. It operates from a single supply over a wide voltage range with a maximum rating up to 30 V for A-version devices, draws a low supply current of approximately 0.8 mA typical independent of supply voltage, and is characterized for operation from 0C to +70C.

A differential comparator is an analog building block that compares two input voltages and drives its output to indicate which is higher. Within the signal-chain hierarchy, comparators sit alongside operational amplifiers in the amplifier IC family but are optimized for fast, saturated switching rather than linear amplification, making them core components in power management, level detection, and mixed-signal systems.

Key features include a common-mode input voltage range that extends to ground (V-), which enables ground-referenced sensing from a single positive supply; a differential input voltage range equal to the maximum-rated supply voltage; low output saturation voltage for efficient driving of loads; and outputs compatible with TTL, MOS, and CMOS logic families. The four independent comparators allow quad-channel threshold monitoring in a single footprint.

Architecturally, each comparator uses a PNP differential input stage that allows inputs to swing down to the negative rail, followed by gain and open-collector output stages that require an external pull-up resistor. Because outputs are open-collector, multiple comparator outputs can be wire-ORed for shared alarm or window-detector functions.

Typical applications include overvoltage and undervoltage supervision, window comparators on power rails, oscillator and relaxation clock generation, analog-to-digital front ends such as flash-converter slicing, and level shifting between analog thresholds and digital logic.

For design, always fit a pull-up resistor (typically 3 kOhm to 15 kOhm) on each open-collector output, and add hysteresis with positive feedback to prevent output chatter near slow-moving thresholds.

This page adds value beyond the datasheet by combining drop-in cross-references, application guidance, comparison tables, and sourcing information in one engineer-oriented reference.

Alternatif penggantian untuk LM339APW — paket yang sama, pin-pada-pin kompatibel. Bagian paket yang berbeda memerlukan kerja ulang PCB diabaikan.

LM339BIPW

✅ Drop-In
📦 14-TSSOP (PW)
Improved B-version: max rating 38 V vs 30 V (+27%), 0.37 mV offset, faster response, pin-to-pin per TI product page

📋 Alternatif referensi (tidak dalam katalog)

LM2901BIPW

✅ Drop-In ⚠️ Spesifikasi Tidak Disahkan
📦 14-TSSOP (PW)
Same B-version die and PW package, temperature grade -40C to +125C vs 0C to +70C, industrial grade

📋 Alternatif referensi (tidak dalam katalog)

LM339APT

✅ Drop-In ⚠️ Spesifikasi Tidak Disahkan
📦 14-TSSOP (PW)
Same die and electricals in the identical TSSOP-14 (PW) body; differs only in tape-and-reel delivery vs tube

📋 Alternatif referensi (tidak dalam katalog)

LM239APT

✅ Drop-In
📦 14-TSSOP
Temperature grade -25C to +85C vs 0C to +70C (wider); quad open-collector comparator, same pinout

📋 Alternatif referensi (tidak dalam katalog)

LM339APW Rating Maksimal & Karakteristik Listrik

Fungsi Quad differential comparator
Number of Channels 4
Tipe Output Open-collector
Maximum Rated Supply Voltage (A-version) 30 V
Maximum Rated Supply Voltage (B-version) 38 V
Differential Input Voltage Range Equal to maximum-rated supply voltage
Common-Mode Input Range Includes ground (V-)
Supply Current (per comparator, B-version typ) 200 uA
Input Offset Voltage (B-version max) 0.37 mV
Input Bias Current (B-version) 3.5 nA
ESD Rating (B-version, HBM) 2 kV
Output Compatibility TTL, MOS, CMOS
Rentang Suhu Kerja 0C to +70C
Paket 14-TSSOP (PW)
Jumlah Pin 14
Tipe Mounting Surface Mount
Status RoHS Compliant

Konfigurasi Pin LM339APW

TSSOP-14 (4.4mm) Package Pinout Diagram TSSOP-14 4.4x5mm, P0.65mm, JEDEC MO-153. 14-pin thin shrink. 1 14 2 13 3 12 4 11 5 10 6 9 7 8 TSSOP-14 (4.4mm)
Pin produk 1 OUT2 — Open-collector output, comparator 2
Pin produk 2 IN2- — Inverting input, comparator 2
Pin produk 3 IN2+ — Non-inverting input, comparator 2
Pin produk 4 IN1- — Inverting input, comparator 1
Pin produk 5 IN1+ — Non-inverting input, comparator 1
Pin produk 6 OUT1 — Open-collector output, comparator 1
Pin produk 7 VCC — Positive supply voltage
Pin produk 8 IN3+ — Non-inverting input, comparator 3
Pin produk 9 IN3- — Inverting input, comparator 3
Pin produk 10 OUT3 — Open-collector output, comparator 3
Pin produk 11 IN4- — Inverting input, comparator 4
Pin produk 12 IN4+ — Non-inverting input, comparator 4
Pin produk 13 OUT4 — Open-collector output, comparator 4
Pin produk 14 GND — Ground / negative supply (V-)

Aplikasi Umum

LM339APW cocok untuk 6 aplikasis: Power Rail Supervision, Window Comparators, Relaxation Oscillators and Clock Generation, Flash ADC Slice and Threshold Slicing, Sensor Threshold Detection, Automotive-Adjacent Industrial Control.

⚡

Power Rail Supervision

The LM339APW's four independent comparators make it a natural fit for multi-rail supervision in servers, industrial controllers, and consumer appliances. Each comparator can monitor one supply rail against a resistor-divider threshold, and because the common-mode input range includes ground, low-voltage rails can be sensed accurately from a single 5 V or 12 V supply. With a maximum rating of 30 V for the A-version, 12 V and 24 V industrial buses can be monitored directly without dividers that attenuate heavily. Open-collector outputs from all four channels can be wire-ORed into a single master reset or fault interrupt, reducing logic gate count. Add hysteresis (tens of millivolts via a 100 kOhm feedback resistor) so that a sagging rail does not cause reset chatter near the threshold.

🔧

Window Comparators

A window comparator uses two of the four LM339APW comparators to flag when a signal leaves an upper and lower limit, ideal for battery-voltage monitoring, sensor range checking, and production test go/no-go fixtures. One comparator watches the upper threshold while the second watches the lower threshold, sharing the same input signal; their open-collector outputs are wired together so a fault pulls the shared line low regardless of which limit is violated. The 30 V A-version rating allows direct connection to unregulated battery nodes, and the low 0.8 mA typical supply current suits battery-powered monitors. Using two channels of one quad device guarantees matched offset behavior between the upper and lower trip points, improving window accuracy compared to mixing devices.

🔧

Relaxation Oscillators and Clock Generation

The LM339APW reliably implements relaxation oscillators, square-wave clocks, and PWM ramps by charging a capacitor through a resistor and switching it around a hysteresis window set by positive feedback on one comparator. Open-collector output switching with defined saturation voltage produces clean edges for gating counters, driving optocouplers, or clocking digital ICs, and the output swing is set by the pull-up supply, so a 5 V logic clock can be generated from a 15 V analog rail. Oscillator frequency is set by the RC network (f is roughly 1/(1.4 RC) for the classic topology), making the frequency stable and trimmable with one potentiometer. The remaining three comparators in the quad can serve as level detectors or a second independent oscillator on the same die.

🖥️

Flash ADC Slice and Threshold Slicing

Multi-comparator threshold slicing is a classic LM339 use: cascaded resistor ladders feed successive LM339APW comparators to convert an analog waveform into a thermometer-coded digital word for simple A/D front ends, bar-graph level meters, and priority encoders. Because each channel draws only about 200 uA typical (B-version) and the inputs operate down to ground, a ladder referenced to 0 V works directly from a single supply. Matching between the four on-die comparators is tighter than mixing separate single-channel parts, which improves differential linearity of the slice. Tie unused comparator inputs to a defined node rather than leaving them floating, and keep the ladder impedance low (a few kOhm per step) so input bias current does not shift the thresholds.

🧩

Sensor Threshold Detection

The LM339APW excels at converting analog sensor outputs into digital status flags for NTC thermistors, photodiodes, pressure-sensor bridges, and current-sense resistors. The ground-including common-mode range permits sensing near 0 V, which is essential for low-side current shunts and grounded thermistor dividers, while the low 3.5 nA input bias current (B-version) keeps high-impedance sensor dividers from shifting. Outputs drive microcontroller GPIO pins directly through pull-ups to the MCU supply, providing simple 3.3 V or 5 V level translation without extra logic. With four channels in one TSSOP-14, a typical multi-sensor board implements over-temperature, over-current, and light-level alarms in a single 9x6.4 mm footprint with minimal quiescent power.

🏭

Automotive-Adjacent Industrial Control

In industrial and light-vehicle control boards operating from 12 V or 24 V rails, the LM339APW provides rugged analog-to-digital boundary logic: detecting limit-switch states, supervising actuator currents, and generating brake/fault signals. The 30 V maximum rating covers 24 V nominal systems with transients attenuated only by simple input dividers, and the open-collector outputs can directly sink indicator LEDs or optocoupler inputs at tens of milliamps of sink current. For designs that must operate in cold enclosures, the pin-compatible LM2901B in the same PW package extends the rating to -40C to +125C with identical layout. Wire-ORing all four open-collector outputs creates a single fault bus that one MCU interrupt pin can monitor.

Ringkasan Produk Direkomendasikan

TL431ACDBZR Texas Instruments Digunakan di dalam: Power Rail Supervision TPS3702 Alternative dedicated supervisor IC Digunakan di dalam: Power Rail Supervision REF3030 3 V precision reference for window limits Digunakan di dalam: Window Comparators TLV431 Low-cost adjustable shunt reference Digunakan di dalam: Window Comparators CD4093BM96 NAND Schmitt trigger for buffered clock distribution Digunakan di dalam: Relaxation Oscillators and Clock Generation NE555DR Texas Instruments Digunakan di dalam: Relaxation Oscillators and Clock Generation CD74HC148 8-line to 3-line priority encoder for thermometer code Digunakan di dalam: Flash ADC Slice and Threshold Slicing TLV3501 High-speed comparator upgrade path Digunakan di dalam: Flash ADC Slice and Threshold Slicing TMP36 Analog temperature sensor feeding comparator threshold Digunakan di dalam: Sensor Threshold Detection ACS712 Allegro MicroSystems Digunakan di dalam: Sensor Threshold Detection TLP291 Photocoupler driven by comparator output for isolation Digunakan di dalam: Automotive-Adjacent Industrial Control LM2901BIPW Extended-temperature drop-in variant Digunakan di dalam: Automotive-Adjacent Industrial Control
What is the LM339APW and what are its key specifications?
The LM339APW is a Texas Instruments quad differential comparator in a 14-pin TSSOP (PW) package with four independent open-collector outputs. Key specifications include a maximum rated supply voltage of 30 V for the A-version, a common-mode input range that includes ground, low supply current of about 0.8 mA typical, and operation from 0C to +70C. Outputs are TTL, MOS, and CMOS compatible. These values are stated in the TI LM339 family datasheet and product pages.
What supply voltage range can the LM339APW operate from?
The LM339APW can operate from a single supply or dual supplies over a wide voltage range, with the A-version maximum rating at 30 V (the newer B-version raises this to 38 V). Dual-supply operation is possible as long as the difference between the two supplies is within the rated range and VCC is at least 2 V. Supply-current drain is essentially independent of supply voltage, per the TI LM339 datasheet.
Does the LM339APW need pull-up resistors on its outputs?
Yes, the LM339APW has open-collector outputs that require external pull-up resistors to function. Connect a pull-up resistor, typically 3 kOhm to 15 kOhm, from each output pin to the desired logic supply voltage, which sets the output high level and makes the outputs compatible with TTL, MOS, and CMOS logic. An advantage of open-collector outputs is that multiple outputs can be wired together (wire-OR) for shared alarm functions, according to the TI datasheet.
What is the operating temperature range of the LM339APW?
The LM339APW is characterized for operation from 0C to +70C, the commercial temperature grade of the LM339A family. According to the TI datasheet, the LM239A covers -25C to +85C, the LM139A covers -55C to +125C for military use, and the LM2901V family covers -40C to +125C. Choose the LM2901A-series in the same TSSOP package if your design must operate below 0C.
What is the difference between LM339APW and the newer LM339B version?
The LM339B is TI's improved B-version of the LM339 family and is a drop-in replacement for the LM339, LM339A, and LM2901A versions in the same package. Key B-version improvements include a maximum rating up to 38 V, 2 kV HBM ESD rating, lower input offset of 0.37 mV, lower input bias current of 3.5 nA, lower supply current of 200 uA per comparator, and faster response time, per the TI product page. The LM339B in the PW package is pin-to-pin compatible with the LM339APW.
Can the STMicroelectronics LM239APT replace the LM339APW?
Yes, the STMicroelectronics LM239APT is a quad differential comparator in the same 14-pin TSSOP package and is cross-referenced against the LM339APW in distributor comparison data. The main differences are the temperature grade: the LM239A is characterized from -25C to +85C versus 0C to +70C for the LM339A, making the LM239A suitable for slightly wider ambient ranges. Verify supply-voltage ratings and response-time requirements in both datasheets before production substitution.
When should I choose the LM339APW over a single-channel comparator?
Choose the LM339APW when your design needs three or four independent threshold comparisons in one footprint, such as multi-rail supervision or window detectors. For a single channel, TI recommends the TL331B; for two channels, the LM393B. Using a quad comparator for one channel wastes board area and idle comparator inputs must be terminated properly, while using three TL331B devices where one LM339APW suffices increases BOM count and placement cost.
Is the LM339APW suitable for zero-crossing and ground-referenced sensing?
Yes, the LM339APW is well suited to ground-referenced sensing because its common-mode input voltage range includes the negative rail (ground in single-supply designs). The PNP differential input stage allows inputs to operate at, and slightly below, V-. This makes it a common choice for zero-crossing detection on AC-coupled signals, ground-fault detection, and low-side current-threshold monitoring, as described in the TI LM339 family datasheet typical applications.
What is the best drop-in replacement for the LM339APW?
The best drop-in replacement for the LM339APW is the TI LM339B in the same PW (TSSOP-14) package. TI explicitly states that the B-version is a drop-in replacement for the LM239, LM339, and LM2901 A and V versions, so no PCB or layout changes are needed. It adds the benefits of a 38 V maximum rating, 0.37 mV input offset, 3.5 nA bias current, and faster response. The LM2901B (wider -40C to +125C temperature range) is another pin-compatible option for extended temperatures.
Where can I download the LM339APW datasheet PDF?
The LM339APW datasheet PDF is available from the Texas Instruments product page at ti.com under the LM339A / LM339 family product folder, which covers the LM139, LM239, LM339, and LM2901 quad differential comparators. The datasheet includes pin configurations, absolute maximum ratings, electrical characteristics, typical application circuits, and package mechanical drawings. Request current pricing, stock, and lead time for the LM339APW through the Request a Quote form on this page.
Where can I find the LM339APW pinout?
The LM339APW pinout follows the standard LM339 TSSOP-14 arrangement: pin 1 is OUT2, pin 2 is IN2-, pin 3 is IN2+, pin 4 is IN1-, pin 5 is IN1+, pin 6 is OUT1, pin 7 is VCC, pin 8 is IN3+, pin 9 is IN3-, pin 10 is OUT3, pin 11 is IN4-, pin 12 is IN4+, pin 13 is OUT4, and pin 14 is GND. This pin assignment is identical across all LM339 family package variants and is documented in the pin configuration section of the TI datasheet.
How should I add hysteresis to an LM339APW comparator circuit?
Add hysteresis by feeding a small fraction of the output voltage back to the non-inverting input through a positive-feedback resistor network. Because the LM339APW output is open-collector, the high-level feedback voltage equals the pull-up supply, and the switching thresholds depend on the pull-up resistor value as well as the feedback divider. Typical resistor values in the 100 kOhm range create tens of millivolts of hysteresis, which prevents output chatter on slow-moving inputs. The TI datasheet typical applications section shows worked hysteresis examples.
Is the LM339APW RoHS compliant and lead-free?
Yes, the LM339APW is RoHS compliant and lead-free. Distributor data cross-checks list the LM339 series with a RoHS compliance code of yes and REACH compliance, and TI ships the PW package in lead-free, RoHS-compliant finishes. For formal certificates of conformance and current environmental documentation, obtain the material content declaration through the Request a Quote form on this page, since certificate revisions are updated by the manufacturer over time.
LM339APW vs LM2901 in the same package - which is better for industrial designs?
For industrial designs, the LM2901-series grade is usually the better choice. The LM339APW is characterized from 0C to +70C, while the LM2901B versions are characterized from -40C to +125C, covering industrial enclosures, vehicles, and outdoor equipment. Both are quad open-collector comparators and pin-compatible in the PW TSSOP-14 package, so swapping is a pure sourcing decision. If your product never sees sub-zero temperatures, the LM339APW is adequate and widely available.
What can replace the LM339APW if it is out of stock?
If the LM339APW is out of stock, pin-compatible replacements include the TI LM339BIPW and TI LM2901BIPW (improved B-version, same TSSOP-14 footprint), the TI LM339APT (same die family, tape-and-reel packaging), and the STMicroelectronics LM239APT quad comparator in the same package. All keep the identical pin assignment and open-collector outputs. Confirm temperature grade and maximum supply rating against your design before ordering, and request current stock through the Request a Quote form on this page.

Data referensi engineering untuk LM339APW — pembandingan, panduan desain, dan informasi konformitas.

Panduan Pemilihan

Choose the LM339APW when you need four general-purpose comparators for 0C to +70C equipment - consumer electronics, indoor instrumentation, office peripherals - with proven open-collector behavior and commodity pricing. Choose the LM339BIPW when your 24 V rail sees transients near or above 30 V (the B-version's 38 V rating plus 2 kV HBM ESD headroom), or when you want the B-version's 0.37 mV offset and faster response without any layout change. Choose the LM2901BIPW for industrial, vehicle, or outdoor products that must operate from -40C to +125C; it is pin-to-pin identical. Choose the STMicroelectronics LM239APT when qualifying a second source is required - it shares the same TSSOP-14 pinout with a -25C to +85C grade. All four selections reuse one PCB footprint, so the decision can be deferred to final sourcing without board redesign.

Pembandingan dengan Alternatif

Parameter Umum Produk Ini LM339BIPW LM2901BIPW LM339APT LM239APT
Package 14-TSSOP (PW) 14-TSSOP (PW) - same 14-TSSOP (PW) - same 14-TSSOP (PW) - same 14-TSSOP - same
Brand Texas Instruments Texas Instruments Texas Instruments Texas Instruments STMicroelectronics
Number of Comparators 4 4 4 4 4
Output Type Open-collector Open-collector Open-collector Open-collector Open-collector
Maximum Rated Supply Voltage 30 V (A-version) 38 V (B-version) 38 V (B-version) 30 V 30 V
Supply Current (per comparator) 0.8 mA typ total family figure 200 uA typ 200 uA typ 0.8 mA typ 0.8 mA typ

Diferensiator Kunci

  • Commercial temperature grade at commodity cost (vsLM2901BIPW)
  • Pin-compatible upgrade path with 38 V rating (vsLM339BIPW)
  • Tube packaging for prototyping (vsLM339APT)

Catatan Desain

Never leave LM339APW outputs or unused comparator inputs floating. Every open-collector output must have a pull-up resistor (3 kOhm to 15 kOhm is typical) to a defined supply, or the output high level is undefined and TTL/CMOS stages driven from it will misread. Tie unused inputs to a rail or a mid-divider so the unused comparator's output stays in a known state; floating PNP input stages can sit in the linear region and draw extra supply current or oscillate.

Add hysteresis whenever the input moves slowly across the threshold, as in battery voltage supervision or NTC sensing. Without positive feedback, input-referred noise of a few millivolts causes output chatter at the transition. A typical implementation feeds the output back to the non-inverting input through a 100 kOhm to 1 MOhm resistor, creating 10 mV to 50 mV of hysteresis depending on the divider impedance and the pull-up supply. Note that because the output is open-collector, the hysteresis band depends on the pull-up resistor value, not a push-pull output level.

Place a 100 nF ceramic decoupling capacitor directly across VCC (pin 7) and GND (pin 14). Although comparator supply current is low (about 0.8 mA typical), open-collector output switching dumps fast current steps into ground, so keep the GND return of the pull-up resistors close to pin 14 to prevent ground bounce between the reference divider and the input grounds. Route the reference divider (e.g., TL431 or resistor ladder) away from output pull-up traces to avoid coupling output transitions into threshold nodes.

Estimated: at VIN = 24 V with all four outputs sinking into 10 kOhm pull-ups to 5 V, each conducting output adds roughly (24 V - 0.2 V)/10 kOhm approximately 2.4 mA of sink current beyond quiescent current; total device dissipation stays well under the small TSSOP-14 thermal limit, but verify input dividers on 24 V rails. A 100 kOhm / 10 kOhm divider on a 24 V rail presents about 24 V across 110 kOhm and biases the input at approximately 2.2 V, which sits safely within the ground-including common-mode range.

Informasi Konformitas

RoHS
Compliant
REACH
Compliant
AEC-Q100
Not Applicable
Bebas Logam Lengket
Yes
Bebas Halogena
Unknown
Mineral Konflik
Unknown

RoHS and REACH compliance codes listed in distributor cross-reference data for the LM339 series. AEC-Q100 qualification is not stated for this commercial-grade part; use the LM2901-family automotive grades for automotive designs.

Data disahkan pada: 2026-11-08 — data disahkan dan disusun oleh tim engineering komponen XAIPART

Pencarian Terkait

LM339APW datasheet LM339APW datasheet pdf LM339APW pinout Texas Instruments LM339APW LM339APW equivalent LM339APW replacement LM339APW vs LM339BIPW LM339 quad comparator TSSOP-14 LM339APW price LM339APW stock LM339 window comparator circuit LM339APW footprint

Komponen dan Istilah Terkait

Texas Instruments LM339APW LM339BIPW LM2901BIPW LM239APT STMicroelectronics LM339 LM2901 TL331B LM393B quad differential comparator voltage comparator amplifier IC open-collector output TSSOP-14 surface mount RoHS REACH HBM ESD rating input offset voltage input bias current common-mode input range window comparator power rail supervision hysteresis
Kutipan Cepat RFQ
Isi detail lengkap — tim penjualan kami akan membalas dalam 24 jam
Nomor Part Manufaktur Paket QTY Harga Target Lengkap
✓
Kutipan telah disubmit!

Kami akan membalas email Anda dalam 24 jam

1
RFQ Dikirim
2
Kutipan Diterima
3
Order Ditempatkan
4
Pembayaran
5
Dikirim
6
Dikirim
Lihat Detil RFQ