MC68HC908JL8CSPE - 8KB Flash 8-bit HC08 MCU | NXP | DIP-32
MPN: MC68HC908JL8CSPE ✗ Akhir HidupMC68HC908JL8CSPE Ringkasan
What is an 8-bit microcontroller? An 8-bit microcontroller (MCU) is a single-chip computer that fetches, decodes, and executes 8-bit-wide instructions, combining a CPU, RAM, Flash/ROM program memory, and peripheral set on a single silicon die. It sits hierarchically between a microprocessor (CPU only) and a System-on-Chip (SoC), typically serving as the lowest-cost, lowest-power computation node in embedded electronics. M68HC08 parts use a customer-specified integrated circuit (CSIC) design strategy with an HC08 core superseding the legacy HC05 instruction set.
Key features include 8 KB on-chip Flash with in-system programming support, 256 bytes of on-chip RAM, a 16-channel 8-bit ADC, two 16-bit dual-channel timer interface modules, a serial communications interface (SCI), and a serial peripheral interface (SPI). The part is also equipped with a real-time interrupt, computer operating properly (COP) watchdog, low-voltage inhibit (LVI), and POR reset blocks for robust system bring-up. The HC08 CPU executes most instructions in 2 to 5 bus cycles at 8 MHz, yielding roughly 1 MIPS at full speed.
Architecturally, the JL8 family belongs to NXP/Freescale's HC08JL/JK sub-line with a unified memory map, vectored interrupts, and a flexible internal oscillator trimmable via factory-programmed Flash trim values. The 32-SDIP footprint simplifies breadboarding and legacy harness compatibility for industrial control modules designed around through-hole pinouts.
Typical applications include appliance control boards (white goods, HVAC damper drivers), automotive body electronics (window lift, lighting controllers), low-cost sensor read-out boards, and industrial control front-ends interfacing to power switches through the ADC, PWM, and SCI peripherals. The 32-SDIP form factor is preferred where socketed field service is desirable.
When designing with this part, pay attention to the LVI/POR behavior during power ramp and ensure the oscillator stabilization delay is observed before code execution begins; CSIC mask revisions may also change peripheral channel assignments, so check the silicon rev against the datasheet Rev. 3.1 (March 2005) when porting code.
This page synthesizes official NXP documentation, distributor pricing, drop-in upgrade alternatives from the same HC908 family, and practical design guidance not found in the manufacturer datasheet alone.
Alternatif penggantian untuk MC68HC908JL8CSPE — paket yang sama, pin-pada-pin kompatibel. Bagian paket yang berbeda memerlukan kerja ulang PCB diabaikan.
Variasi di dalam seri ini
Model-series yang sama yang kompatibel dengan penggantian MC68HC908JL8CSPE (sama faktor bentuk dan footprint) — berbeda di dalam Mounting Type, Operating Temperature, RAM Size, Connectivity, Program Memory Size.
MC68HC908JK8CPE
✅ Drop-In📋 Alternatif referensi (tidak dalam katalog)
MC68HC908KL8CPE
✅ Drop-In📋 Alternatif referensi (tidak dalam katalog)
MC68HC908JK1CPE
✅ Drop-In📋 Alternatif referensi (tidak dalam katalog)
MC68HC908JL8MPE
✅ Drop-In📋 Alternatif referensi (tidak dalam katalog)
MC68HC908GR8CPE
✅ Drop-In📋 Alternatif referensi (tidak dalam katalog)
MC68HC908JL8CSPE Rating Maksimal & Karakteristik Listrik
| Core | HC08 |
| CPU Architecture | 8-bit |
| Program Memory Type | Flash |
| Program Memory Size | 8 KB (8K x 8) |
| RAM Size | 256 B (256 x 8) |
| Frekuensi Bawah Maximum | 8 MHz |
| Supply Voltage (Vcc/Vdd) | 2.7 V to 5.5 V |
| Suhu Kerja | -40 C to +85 C |
| Paket / Case | 32-SDIP |
| Jumlah Pin | 32 |
| Tipe Mounting | Through Hole |
| ADC | 8-bit, multi-channel |
| Communication Interfaces | SCI (UART), SPI |
| Timers | Dual 16-bit timer interface modules |
| Watchdog | COP watchdog |
| Reset / Brown-out | POR + LVI (Low Voltage Inhibit) |
Konfigurasi Pin MC68HC908JL8CSPE
| Pin produk 1 | PTA0/TCH0 — Port A bit 0 / Timer channel 0 |
| Pin produk 2 | PTA1/TCH1 — Port A bit 1 / Timer channel 1 |
| Pin produk 3 | PTA2 — Port A bit 2 |
| Pin produk 4 | PTA3 — Port A bit 3 |
| Pin produk 5 | PTA4 — Port A bit 4 |
| Pin produk 6 | PTA5 — Port A bit 5 |
| Pin produk 7 | PTA6 — Port A bit 6 |
| Pin produk 8 | PTA7 — Port A bit 7 |
| Pin produk 9 | Vdd — Power supply |
| Pin produk 10 | Vss — Ground |
| Pin produk 11 | OSC1 — Crystal oscillator input |
| Pin produk 12 | OSC2 — Crystal oscillator output |
| Pin produk 13 | RST — External reset input |
| Pin produk 14 | IRQ — External interrupt request |
| Pin produk 15 | PTB0/ADC0 — Port B bit 0 / ADC channel 0 |
| Pin produk 16 | PTB1/ADC1 — Port B bit 1 / ADC channel 1 |
| Pin produk 17 | PTB2/ADC2 — Port B bit 2 / ADC channel 2 |
| Pin produk 18 | PTB3/ADC3 — Port B bit 3 / ADC channel 3 |
| Pin produk 19 | PTB4/ADC4 — Port B bit 4 / ADC channel 4 |
| Pin produk 20 | PTB5/ADC5 — Port B bit 5 / ADC channel 5 |
| Pin produk 21 | PTB6/ADC6 — Port B bit 6 / ADC channel 6 |
| Pin produk 22 | PTB7/ADC7 — Port B bit 7 / ADC channel 7 |
| Pin produk 23 | PTC0/SPSCK — Port C bit 0 / SPI clock |
| Pin produk 24 | PTC1/MOSI — Port C bit 1 / SPI MOSI |
| Pin produk 25 | PTC2/MISO — Port C bit 2 / SPI MISO |
| Pin produk 26 | PTC3/SS — Port C bit 3 / SPI slave select |
| Pin produk 27 | PTC4/TxD — Port C bit 4 / SCI transmit |
| Pin produk 28 | PTC5/RxD — Port C bit 5 / SCI receive |
| Pin produk 29 | PTC6 — Port C bit 6 |
| Pin produk 30 | PTC7 — Port C bit 7 |
| Pin produk 31 | BKGD — Background Debug Mode pin |
| Pin produk 32 | NC — Not connected (per datasheet) |
Aplikasi Umum
MC68HC908JL8CSPE cocok untuk 7 aplikasis: White-Goods Appliance Control Boards, Automotive Body Electronics, Industrial Sensor Read-out Front-Ends, Low-Cost HVAC Damper and Fan Drivers, Vending and POS Peripheral Controllers, Educational and Hobby Development Boards, Lighting Control and Ballast Drivers.
White-Goods Appliance Control Boards
The MC68HC908JL8CSPE's 8-bit HC08 core and 2.7-5.5 V supply make it ideal for low-cost white-goods controllers in washing machines, dishwashers, and refrigerators. Its 8 KB Flash stores motor-control state machines and user-interface logic, while the dual 16-bit timer interface modules drive TRIAC phase-angle control for heater and pump loads. The 32-SDIP package simplifies through-hole assembly on the wave-solder lines common in major-appliance manufacturing. The COP watchdog and POR/LVI reset block survive the brown-out events typical when compressor motors kick in, making the part a legacy staple in cost-sensitive home appliances.
Direkomendasikan
Automotive Body Electronics
The MC68HC908JL8CSPE is well suited to automotive body modules such as window-lift controllers, lighting drivers, and seat-position switches, where its 8 KB Flash and 256 bytes of RAM host simple supervisory logic. The 5.5 V absolute maximum tolerates 12 V battery transients when combined with external TVS clamps, and the ADC channels read potentiometer or thermistor inputs directly without signal conditioning. Operating from -40 C to +85 C it covers cabin electronics, and the COP watchdog catches firmware deadlocks that would otherwise leave a window partially open. The 32-SDIP footprint remained popular in pre-2008 automotive service harnesses.
Direkomendasikan
Industrial Sensor Read-out Front-Ends
For industrial sensor read-out modules, the MC68HC908JL8CSPE provides 8 KB of Flash to hold calibration lookup tables plus an 8-bit ADC for digitizing strain-gauge, thermistor, or 4-20 mA loop signals. The serial peripheral interface (SPI) drives an external DAC or digital isolator that bridges to a PLC backplane, while the SCI channel streams diagnostic telemetry. The 32-SDIP through-hole pinout simplifies socketed field service on factory floor installations, allowing technicians to swap modules without desoldering. The 2.7-5.5 V supply range is compatible with 24 V industrial bus rails after external step-down, making it a recurring choice for legacy PLC I/O cards.
Direkomendasikan
Low-Cost HVAC Damper and Fan Drivers
The MC68HC908JL8CSPE's PWM channels and dual 16-bit timers generate variable-duty outputs to drive small triac-controlled fan motors or damper actuators in residential HVAC equipment. Its 2.7-5.5 V supply rails accept 24 VAC wall-transformer-rectified power after a simple LDO, and the 8-bit ADC reads temperature sensors for closed-loop control. The internal COP watchdog recovers from line-noise-induced firmware hangs common on long HVAC harnesses. The 32-SDIP form factor continues to ship in replacement boards sold through HVAC parts distributors, making this MCU a recurring legacy specification.
Direkomendasikan
Vending and POS Peripheral Controllers
Vending machines and point-of-sale peripherals rely on the MC68HC908JL8CSPE for keypad scanning, coin acceptor signaling, and small LCD control. The 8 KB Flash holds menu firmware and coin-handling state machines while the SCI channel exchanges transaction data with a back-office controller. The 32-SDIP through-hole package simplifies field replacement because vending-machine service technicians can swap boards with basic tools. The 2.7-5.5 V rail is compatible with 5 V logic peripherals that dominated the legacy vending-machine market.
Direkomendasikan
Educational and Hobby Development Boards
The MC68HC908JL8CSPE is widely used on university and hobbyist development boards because the 32-SDIP package drops into a breadboard socket and the HC08 instruction set is straightforward to teach. Its on-chip 8-bit ADC, PWM timers, and SCI/SPI peripherals allow students to explore real embedded protocols with a single chip. The BDM port supports modern in-circuit debuggers such as USBDM and P&E Cyclone. Legacy stock from Rochester Electronics keeps labs supplied even though NXP has retired the part; many courses still rely on the JL8CSPE specifically because of its pin-accessible through-hole footprint.
Direkomendasikan
Lighting Control and Ballast Drivers
Lighting ballasts and dimmer modules used the MC68HC908JL8CSPE to drive trailing-edge MOSFET dimmers and DALI bridges before the CFL phase-out. The dual 16-bit timer modules generate the zero-cross detection delays and PWM outputs needed for phase-angle control, and the 8-bit ADC measures photocell feedback. The part operates from -40 C to +85 C, satisfying enclosed-luminaire thermal budgets. The 32-SDIP package is favored by aftermarket ballast manufacturers because socketed replacement lets electricians swap units without reflow soldering.
Direkomendasikan
Ringkasan Produk Direkomendasikan
Data referensi engineering untuk MC68HC908JL8CSPE — pembandingan, panduan desain, dan informasi konformitas.
Panduan Pemilihan
Pembandingan dengan Alternatif
| Parameter Umum | Produk Ini | MC68HC908JK8CPE | MC68HC908KL8CPE | MC68HC908JK1CPE | MC68HC908JL8MPE | MC68HC908GR8CPE |
|---|---|---|---|---|---|---|
| Package | 32-SDIP | 32-SDIP - same | 32-SDIP - same | 32-SDIP - same | 32-SDIP - same | 32-SDIP - same |
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Core | HC08 | HC08 | HC08 | HC08 | HC08 | HC08 |
| Program Memory | 8 KB Flash | 8 KB Flash | 8 KB Flash | 1.5 KB Flash | 8 KB Flash | 8 KB Flash |
| RAM Size | 256 B | 256 B | 256 B | 128 B | 256 B | 384 B |
| Maximum Clock Frequency | 8 MHz | 8 MHz | 8 MHz | 8 MHz | 8 MHz | 8 MHz |
| Supply Voltage | 2.7 V to 5.5 V | 2.7 V to 5.5 V | 2.7 V to 5.5 V | 2.7 V to 5.5 V | 2.7 V to 5.5 V | 2.7 V to 5.5 V |
| Operating Temperature | -40 C to +85 C | -40 C to +85 C | -40 C to +85 C | -40 C to +85 C | -40 C to +85 C | -40 C to +85 C |
| Lifecycle Status | Obsolete | Obsolete | Obsolete | Obsolete | Obsolete | Obsolete |
Diferensiator Kunci
- Closest same-family pin-compatible alternative (vsMC68HC908JK8CPE)
- Larger memory alternative in same package (vsMC68HC908KL8CPE)
- Richer peripheral set in same package (vsMC68HC908GR8CPE)
- Lower cost but reduced memory variant (vsMC68HC908JK1CPE)
Catatan Desain
Estimated: With Vdd = 5 V, the MC68HC908JL8CSPE draws typical active current under 10 mA from a 2.7-5.5 V supply, giving roughly 50 mW dissipation worst case. Place a 0.1 uF decoupling capacitor within 5 mm of the Vdd and Vss pins, plus a bulk 10 uF tantalum or aluminum polymer bypass to absorb motor inrush when used in appliance or automotive body electronics. The LVI block generates a reset if Vdd drops below about 2.5 V, so design headroom above 2.7 V in noisy 5 V systems.
The MC68HC908JL8CSPE in 32-SDIP typically dissipates well under 0.5 W in active mode, keeping the junction well below thermal limits in 0-70 C commercial designs. In enclosed-luminaire or under-hood automotive applications approaching +85 C ambient, derate supply current and clock frequency or migrate to the MC9S08 family rated for +125 C automotive use. Avoid placing the part adjacent to high-dissipation MOSFETs without copper thermal relief.
Keep BDM (background debug mode) and RST traces short and away from switching nodes; pull-up the RST line to Vdd through a 10 kohm resistor and add a 0.1 uF cap for debounce. Place the OSC1/OSC2 crystal within 5 mm of the pins and route both traces over a continuous ground pour to avoid oscillator startup failures. Route ADC inputs away from PWM outputs by at least 2 mm or use a guard trace to ground for sensor-noise immunity. For automotive applications add TVS protection on all pins accessible from external harnesses.
Do not exceed the 5.5 V absolute-maximum rating on Vdd — even brief transients from inductive loads can latch the part. Always drain the security byte into a non-programmable state before production locking, otherwise the Flash erase/write routines can lock themselves out. The CSPE windowed/ceramic-lid package is intended for development; production builds should move to the standard CP package. When migrating code written for HC08 to HCS08 (MC9S08 family), verify that the interrupt vector base and ADC register layouts match, they differ across revisions.
Informasi Konformitas
Compliance status not stated in the verified NXP product page or distributor listings. JL8 family was launched in 2005 and pre-dates the RoHS directive being strictly enforced at NXP. The CSPE suffix indicates a windowed/ceramic-lid development package, not a production lead-free variant. For RoHS-compliant equivalent, switch to a modern S08 part.
