MCP3561RT-E/ST - 24-Bit 153.6 kSPS ADC | Microchip
MPN: MCP3561RT-E/ST ✓ AktifMCP3561RT-E/ST Ringkasan
A delta-sigma ADC is a voltage-to-digital converter category that uses oversampling, digital filtering, and noise shaping to provide high resolution and excellent rejection of out-of-band noise. In the signal-processing hierarchy, it belongs to the ADC family within data-converter integrated circuits and broader semiconductor systems. The MCP3561RT-E/ST combines a high-resolution conversion engine with an internal reference and programmable conversion speed for applications requiring accurate digital representations of low-frequency or slowly changing analog signals.
Key features include 24-bit resolution, programmable data rates up to 153.6 kSPS, support for one differential or two single-ended channels, an SPI serial interface, and a typical supply current of 930 µA for the related MCP3561R device identified in the family documentation. Its 2.7 V to 3.6 V operating supply range, 7 ppm typical INL family specification, and integrated voltage reference reduce the number of external precision components required.
The converter architecture is suited to precision instrumentation rather than high-bandwidth waveform capture. Oversampling and digital filtering can suppress out-of-band noise, while the 24-bit word length provides additional numerical headroom for gain correction, calibration, and sensor linearization. System designers must still account for input settling time, reference accuracy, digital filtering latency, and the time required to complete each conversion when calculating update rates.
Typical applications include industrial process measurement, battery-powered sensor acquisition, medical instrumentation, environmental monitoring, and precision pressure or temperature sensing. The 153.6 kSPS maximum rate supports sampling of many slow-changing sensor outputs while the 20-pin TSSOP package keeps the design compact for embedded measurement boards.
For reliable operation, use the manufacturer pin-description table when assigning analog inputs, supply pins, grounds, and digital interface signals. Place input and reference-decoupling capacitors close to their associated pins, keep analog routing away from SPI switching nodes, and allow the selected digital filter to settle after each conversion.
This page consolidates the exact MPN characteristics, verified sourcing references, same-family drop-in options, parameter comparisons, and practical ADC design guidance. It is intended to support component selection, PCB implementation, and lifecycle-aware sourcing decisions for engineers evaluating the MCP3561RT-E/ST.
Alternatif penggantian untuk MCP3561RT-E/ST — paket yang sama, pin-pada-pin kompatibel. Bagian paket yang berbeda memerlukan kerja ulang PCB diabaikan.
Variasi di dalam seri ini
Model-series yang sama yang kompatibel dengan penggantian MCP3561RT-E/ST (sama faktor bentuk dan footprint) — berbeda di dalam Package, Resolution, Converter Type, Input Configuration, Operating Temperature Range.
MCP3561R-E/ST
✅ Drop-InKontak untuk harga
Lihat Datasheet →MCP3561-E/ST
✅ Drop-InKontak untuk harga
Lihat Datasheet →MCP3561RT-E/ST Rating Maksimal & Karakteristik Listrik
| Resolusi | 24 bit |
| Converter Type | Low-noise delta-sigma ADC |
| Maximum Sampling Rate | 153.6 kSPS |
| Input Configuration | 2 single-ended inputs or 1 differential input |
| Supply Voltage Range | 2.7 V to 3.6 V |
| Typical Supply Current | 930 µA |
| Typical INL | 7 ppm |
| Antarmuka | SPI |
| Internal Voltage Reference | Integrated |
| Internal Oscillator | Integrated |
| Rentang Suhu Kerja | -40 °C to +85 °C |
| Paket | 20-pin TSSOP |
| Tipe Mounting | Surface mount |
| Status RoHS | Compliant |
| Data Rate Control | Programmable up to 153.6 kSPS |
| Input Type | Single-ended or differential analog input |
| Digital Data Format | 24-bit ADC data |
| Serial Interface Type | SPI |
| Product Series | MCP3561 |
| Temperature Grade | -40 °C to +85 °C |
| Packaging Form | Tape and reel |
MCP3561RT-E/ST 20-pin tssop Diamant Konfigurasi Panduan
Konfigurasi pin untuk MCP3561RT-E/ST (20-pin tssop pakai pakai). Komponen analog ini memiliki pin masukan, keluaran, dan pengirim daya. Lihat datasheet produsen untuk konfigurasi pin offset null, kompensasi, dan pengaktifan. Ideal untuk peralatan sinyal dan kabel penggandaran.
Tidak ada data diatribut pin yang tersedia untuk MCP3561RT-E/ST.
Lihat ke: datasheet produk untuk konfigurasi pin penuh.
Aplikasi Umum
MCP3561RT-E/ST cocok untuk 6 aplikasis: Industrial Process Measurement, Battery-Powered Sensor Acquisition, Medical Signal Acquisition, Environmental Monitoring, Precision Pressure Sensing, Automated Test Equipment.
Industrial Process Measurement
The MCP3561RT-E/ST fits industrial process-measurement front ends that monitor slowly changing pressure, flow, level, or temperature signals. Its 24-bit resolution provides substantial numerical headroom for calibration and gain correction, while the programmable rate up to 153.6 kSPS is more than adequate for many process sensors. Use one differential input when the transducer is balanced and rejection of common-mode noise is important, or use both single-ended inputs for two related sensor channels. The 2.7 V to 3.6 V operating range supports regulated low-voltage rails. Place the input network and reference-decoupling components close to the converter, and allow the configured digital filter to settle before accepting each measurement.
Direkomendasikan
Battery-Powered Sensor Acquisition
The MCP3561RT-E/ST is appropriate for battery-powered environmental and portable sensing when a low-resolution ADC would waste the available sensor accuracy. The family specification lists a typical supply current of 930 µA, and the integrated voltage reference and oscillator reduce the need for continuously powered external support circuitry. The 2.7 V to 3.6 V range can operate from a suitable regulated point in a low-voltage battery system. Select lower conversion rates and longer settling intervals when energy use matters more than latency. Check the sensor’s output range against the ADC input limits, and avoid leaving unused analog inputs floating because their state can affect repeatability and channel-to-channel behavior.
Direkomendasikan
Medical Signal Acquisition
The MCP3561RT-E/ST can serve as the analog front end of low-bandwidth medical monitoring equipment when the selected sensor and isolation architecture meet the applicable safety requirements. Its 24-bit resolution captures small, slowly varying physiological or diagnostic signals with enough digital headroom for scaling and filtering, while the differential-input option helps reject common-mode interference. The 153.6 kSPS maximum rate is appropriate for many pressure, temperature, and biochemical monitoring loops, but not for high-bandwidth waveform acquisition. Keep sensitive analog traces short, isolated from SPI activity, and referenced to a low-noise supply. Confirm device qualification, isolation, patient-safety, and system-level standards for the finished equipment.
Direkomendasikan
Environmental Monitoring
The MCP3561RT-E/ST is well matched to environmental monitoring systems that digitize humidity, temperature, gas, pH, or light-sensor outputs. These signals usually change slowly, allowing the converter’s programmable rate up to 153.6 kSPS to be reduced for lower power consumption and shorter conversion latency. The 24-bit word length supports software linearization and compensation of sensor drift, while two single-ended inputs can serve temperature and humidity channels from the same measurement module. The internal reference and oscillator simplify field installation by reducing external precision components. Use stable sensor excitation, low-noise analog routing, and input protection appropriate for the environment, and recalibrate when long-term drift is significant.
Direkomendasikan
Precision Pressure Sensing
The MCP3561RT-E/ST supports high-resolution pressure-sensor acquisition in industrial, automotive-adjacent, and laboratory systems. A differential bridge or ratiometric sensor can use the converter’s differential input, helping preserve accuracy when sensor excitation varies and common-mode voltage is elevated. The 24-bit resolution gives designers useful margin for bridge sensitivity, reference accuracy, offset correction, and gain calibration. The 153.6 kSPS ceiling is appropriate for static pressure, slow pressure ramps, and many pneumatic-control loops. Match the input bandwidth to the selected digital filter, maintain equal routing for differential pairs, and place input filtering close to the ADC to minimize noise pickup and settling time.
Direkomendasikan
Automated Test Equipment
The MCP3561RT-E/ST can serve as a measurement ADC in compact automated test equipment that evaluates slow analog outputs, resistive sensors, or reference voltages. Its 24-bit resolution supports fine measurement granularity, while SPI provides a straightforward connection to a test controller or mixed-signal microcontroller. The maximum rate of 153.6 kSPS permits sequential measurements across multiple channels without the complexity of a high-speed flash converter. Use the integrated reference and oscillator for a self-contained measurement channel, but include calibration records for gain, offset, and reference drift when traceability matters. Keep clock and SPI routing away from the analog input, and design the firmware around the selected filter latency and conversion-complete timing.
Direkomendasikan
Ringkasan Produk Direkomendasikan
Data referensi engineering untuk MCP3561RT-E/ST — pembandingan, panduan desain, dan informasi konformitas.
Panduan Pemilihan
Pembandingan dengan Alternatif
| Parameter Umum | Produk Ini | MCP3561R-E/ST | MCP3561-E/ST |
|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology |
| Resolution | 24 bit | 24 bit | 24 bit |
| Maximum Sample Rate | 153.6 kSPS | 153.6 kSPS | 153.6 kSPS |
Diferensiator Kunci
- High conversion rate within a low-noise 24-bit architecture (vsMCP3301T-BI/SN)
- Integrated reference and oscillator simplify the measurement channel (vsMCP3561-E/ST)
- Flexible single-ended or differential acquisition (vsMCP3561R-E/ST)
Catatan Desain
Place input-filter, supply-decoupling, and reference-decoupling components close to their associated MCP3561RT-E/ST pins. Keep the two differential-input traces short, closely spaced, and routed away from SPI, oscillator, and power-converter switching paths. A solid ground plane reduces return-path discontinuities, while a quiet analog ground region helps prevent digital activity from coupling into the measured signal.
Design the firmware to account for digital-filter settling time, conversion duration, and SPI transfer latency. The 153.6 kSPS figure is a conversion-rate limit, not necessarily the rate at which a completely settled result can be sampled in every mode. Use the manufacturer timing diagrams for each data-rate configuration and avoid reusing a conversion result before the configured filter has completed its settling interval.
Do not assume that equal resolution guarantees interchangeability. MCP3561RT-E/ST suffix distinctions may affect ordering, temperature, or configuration options, so compare the complete ordering information and pin descriptions before substituting MCP3561R-E/ST or MCP3561-E/ST. Also verify the analog input range and common-mode limits; a 24-bit converter can still saturate when the sensor output exceeds the supported input span.
Operate the converter from a stable source within its 2.7 V to 3.6 V supply range and verify that the digital interface levels match the connected controller. Bypass the supply pins with local ceramic capacitance and avoid routing converter switching current through the analog-input area. If the system contains a switching regulator, place the ADC’s supply filtering and grounding strategy close to the measurement circuitry rather than at the regulator.
Informasi Konformitas
RoHS compliance is identified for the exact MCP3561RT-E/ST ordering code. No authoritative information for the other requested compliance categories was identified.