MCP604-E/ST - 4-Channel 2.8MHz CMOS Op Amp | Microchip
MPN: MCP604-E/ST ✓ AktifMCP604-E/ST Ringkasan
A CMOS operational amplifier is a voltage-controlled, differential active device used to amplify voltage differences, buffer analog signals, and implement feedback-based control and filtering circuits. The MCP604 belongs to the broader operational-amplifier hierarchy, where it combines low bias current, low quiescent current, and rail-to-rail operation. Its four amplifiers share one package, making it useful when a design needs several similar analog channels without allocating four separate packages.
The MCP604-E/ST provides 2.8 MHz typical gain-bandwidth, 2.3 V/µs slew rate, 75 dB minimum common-mode rejection, and 2 mV typical input-offset voltage. Rail-to-rail output and input stages support signal levels extending toward the supply rails, while 230 µA typical operating current per amplifier limits power demand in battery-operated or multi-channel systems. Unity-gain stability also simplifies direct buffering and basic gain configurations.
The advanced CMOS implementation supports low bias current, high open-loop gain, and low power consumption. Because all four channels share one package, supply routing and bypassing must support the aggregate channel load. Decoupling capacitance should be placed close to the power pins, and sensitive analog inputs should remain short and away from switching nodes. The device is intended for precision control and general-purpose analog processing rather than high-speed video or high-voltage operation.
Typical applications include sensor-signal conditioning, current measurement, analog filtering, voltage buffering, instrumentation, and precision control loops. Four integrated channels can support repeated sensing, multi-axis control, or parallel signal conditioning while simplifying assembly. The low typical operating current is particularly useful in portable instrumentation, while the 6 V maximum supply supports conventional 3.3 V and 5 V analog systems.
The main design consideration is confirming that the input and output common-mode ranges cover the actual signal excursion. Rail-to-rail operation reduces headroom concerns, but output current, load capacitance, noise, and output-voltage limits still require verification for the chosen gain and frequency. Input offset voltage and bias current should also be included in error budgets for precision measurements.
This page combines verified manufacturer and distributor information with same-package drop-in alternatives, parameter comparisons, application guidance, and practical design notes. The alternatives are presented as footprint-compatible engineering options, but production use still requires validation of supply voltage, temperature grade, electrical limits, and lifecycle status against the original design requirements.
Alternatif penggantian untuk MCP604-E/ST — paket yang sama, pin-pada-pin kompatibel. Bagian paket yang berbeda memerlukan kerja ulang PCB diabaikan.
MCP604-E/STVAO
✅ Drop-In ⚠️ Spesifikasi Tidak Disahkan📋 Alternatif referensi (tidak dalam katalog)
MCP604T-E/STVAO
✅ Drop-In ⚠️ Spesifikasi Tidak Disahkan📋 Alternatif referensi (tidak dalam katalog)
MCP6004-I/ST
✅ Drop-In ⚠️ Spesifikasi Tidak Disahkan📋 Alternatif referensi (tidak dalam katalog)
MCP6004T-I/ST
✅ Drop-In ⚠️ Spesifikasi Tidak Disahkan📋 Alternatif referensi (tidak dalam katalog)
MCP604-E/SL
✅ Drop-In ⚠️ Spesifikasi Tidak Disahkan📋 Alternatif referensi (tidak dalam katalog)
MCP604-E/ST Rating Maksimal & Karakteristik Listrik
| Amplifier Type | Quad CMOS operational amplifier |
| Number of Channels | 4 channels |
| Supply Voltage Range | 2.7 V to 6 V |
| Gain-Bandwidth Product | 2.8 MHz typical |
| Slew Rate | 2.3 V/µs |
| Typical Operating Current | 230 µA per amplifier |
| Input Offset Voltage | 2 mV |
| Common-Mode Rejection Ratio | 75 dB minimum |
| Input Common-Mode Range | Rail-to-rail, including ground |
| Output Swing | Rail-to-rail |
| Gain Configuration | Unity-gain stable |
| Paket | 14-pin TSSOP |
| Tipe Mounting | Surface mount |
| Process Technology | Advanced CMOS |
| Lead Time | 2 weeks standard lead time |
| Status Lingkungan Hidup | Active |
| Status RoHS | Compliant |
| Lead-Free Status | Lead-free |
MCP604-E/ST 14-pin tssop Diamant Konfigurasi Panduan
Konfigurasi pin untuk MCP604-E/ST (14-pin tssop pakai pakai). Komponen analog ini memiliki pin masukan, keluaran, dan pengirim daya. Lihat datasheet produsen untuk konfigurasi pin offset null, kompensasi, dan pengaktifan. Ideal untuk peralatan sinyal dan kabel penggandaran.
Tidak ada data diatribut pin yang tersedia untuk MCP604-E/ST.
Lihat ke: datasheet produk untuk konfigurasi pin penuh.
Aplikasi Umum
MCP604-E/ST cocok untuk 6 aplikasis: Sensor Signal Conditioning, Current Sensing, Precision Analog Filtering, Voltage Buffering, Precision Control Loops, Portable Instrumentation.
Sensor Signal Conditioning
The MCP604-E/ST is well suited to conditioning four sensor channels because each amplifier combines a 2.8 MHz typical gain-bandwidth product with 230 µA typical operating current. The four amplifiers can amplify weak sensor outputs, buffer high-impedance sources, or implement active filters without requiring four separate packages. Rail-to-rail input operation including ground helps preserve usable signal range in low-voltage systems, while the 2.7 V to 6 V supply range supports 3.3 V and 5 V designs. Designers should still include the amplifier's 2 mV typical input-offset voltage in the measurement error budget and verify that the selected gain produces acceptable bandwidth and output swing.
Direkomendasikan
Current Sensing
The MCP604-E/ST can serve as a transimpedance or voltage buffer in current-sensing circuits where low power and multiple analog channels are useful. Its 2.8 MHz typical gain-bandwidth provides useful bandwidth for moderate-speed measurements, while 230 µA typical operating current per amplifier limits the penalty of keeping four channels active. Rail-to-rail input and output stages can improve utilization of a 3.3 V or 5 V supply. The practical trade-off is that input offset voltage, input bias current, and output settling affect accuracy, so resistor and capacitor values must be checked with the complete shunt and amplifier specifications.
Direkomendasikan
Precision Analog Filtering
Active filters can use the unity-gain-stable MCP604-E/ST to implement gain, low-pass, or multi-stage analog conditioning. Its 2.8 MHz typical gain-bandwidth and 2.3 V/µs slew rate are sufficient for many low- and medium-frequency control and measurement channels, while four amplifiers allow a filter bank or repeated signal processing stages in one 14-pin TSSOP. Rail-to-rail output swing is useful when filter signals occupy much of the available supply range. Component tolerances, amplifier noise, offset, and the finite bandwidth must be included in the filter transfer-function design.
Direkomendasikan
Voltage Buffering
The MCP604-E/ST can buffer up to four voltage sources without introducing the complexity of a discrete transistor buffer at each node. Its unity-gain stability supports direct voltage-follower use, while the 2.8 MHz typical gain-bandwidth and 2.3 V/µs slew rate provide sufficient performance for low-frequency sensor, control, and instrumentation signals. Rail-to-rail input and output behavior reduces the required headroom around ground and the upper supply rail. Buffer stability should be checked against capacitive loading, and the 230 µA typical current per amplifier should be included in the system's power budget.
Direkomendasikan
Precision Control Loops
In precision control and feedback systems, the MCP604-E/ST provides four low-power amplifier channels with 2.8 MHz typical gain-bandwidth and rail-to-rail operation. The bandwidth can support servo, actuator-control, and setpoint-conditioning loops operating below the amplifier's practical closed-loop limits, while 75 dB minimum common-mode rejection helps reject common-mode disturbance on feedback signals. The principal trade-off is the 2 mV typical input-offset voltage, which can affect the control setpoint or error amplifier. System-level accuracy should therefore be calculated with offset, bias current, output swing, and load effects included.
Direkomendasikan
Portable Instrumentation
The MCP604-E/ST is appropriate for portable instrumentation where four measurement or control channels must be packaged efficiently and powered from a limited source. Each amplifier has a typical operating current of 230 µA, and the device operates from 2.7 V to 6 V, allowing use with low-voltage battery-regulated rails. Four integrated channels reduce component count and simplify routing for sensor amplifiers, buffer stages, and active filters. Because no numeric price was supplied in the verified data, cost should be obtained through a current distributor quote, while battery life should be evaluated with actual duty cycle and load behavior.
Direkomendasikan
Ringkasan Produk Direkomendasikan
Data referensi engineering untuk MCP604-E/ST — pembandingan, panduan desain, dan informasi konformitas.
Panduan Pemilihan
Pembandingan dengan Alternatif
| Parameter Umum | Produk Ini | MCP604-E/STVAO | MCP604T-E/STVAO | MCP6004-I/ST | MCP6004T-I/ST |
|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 14-pin TSSOP | 14-pin TSSOP | 14-pin TSSOP | 14-pin TSSOP | 14-pin TSSOP |
| Number of Channels | 4 channels | 4 channels | 4 channels | 4 channels | 4 channels |
Diferensiator Kunci
- Four amplifiers share one 14-pin TSSOP package (vsMCP6004-I/ST)
- Low-power operation with 230 µA typical current per amplifier (vsMCP604-E/STVAO)
- Rail-to-rail operation includes the ground rail (vsMCP604T-E/STVAO)
Catatan Desain
Place the supply bypass capacitor immediately beside the MCP604-E/ST power pins and connect it to a low-impedance ground plane. Four amplifier channels share the package supply pins, so transient demand is the aggregate of all active channels rather than one 230 µA channel. Route sensitive inputs away from power converters, clock lines, and high-current return paths. The verified data confirms a 14-pin TSSOP package, but the authoritative pin numbers and exposed-pad arrangement must be taken from the current Microchip package drawing before layout release.
Use short, guarded traces for high-impedance sensor inputs because input bias current and leakage can create measurable voltage errors. The MCP604-E/ST is specified with 2 mV typical input-offset voltage and 75 dB minimum common-mode rejection, but neither rating removes errors caused by leakage or inadequate grounding. If a source impedance is high, calculate the bias-current-induced error against the actual input-bias-current limit and consider guarding or a nearby low-input-bias-current alternative.
Design the 2.7 V to 6 V supply so that transients remain below the absolute maximum rating and the signal does not exceed the amplifier's common-mode range. Rail-to-rail input and output operation improves low-voltage headroom, but it does not remove output-current, output-voltage, or load limitations. For a 3.3 V system, verify that the measured output can reach the required logic or sensor levels while maintaining the intended gain and load.
Do not substitute the MCP604-E/SL or MCP6024-E/P ordering options without verifying their package and pinout. The confirmed MCP604-E/ST is a 14-pin TSSOP device, and a shared amplifier function does not prove a shared land pattern. Likewise, suffix changes such as T, I, or VAO can encode temperature, packaging, or production distinctions. Before approving any replacement, compare the ordering tables, pin functions, common-mode range, offset, bandwidth, bias current, and temperature grade.
Informasi Konformitas
RoHS compliance and lead-free status are explicitly reported in the verified component data. The supplied data does not establish REACH, halogen-free, AEC-Q100, or conflict-minerals status.
