MKL26Z32VLH4 - Kinetis KL26 48MHz Cortex-M0+ MCU, 32KB Flash, USB | NXP
MPN: MKL26Z32VLH4 ✓ AktifMKL26Z32VLH4 Ringkasan
A microcontroller (MCU) is a single-chip computer that integrates a CPU core, memory, and programmable peripherals. Within the broader semiconductor taxonomy, the MKL26Z32VLH4 sits in the hierarchy MCU -> 32-bit MCU -> ARM Cortex-M MCU -> low-power MCU -> Kinetis family. The Cortex-M0+ core is the smallest and most energy-efficient member of the ARM Cortex-M family, designed for cost-sensitive embedded applications where deterministic interrupt response and low active/idle power matter more than raw compute.
Key features include 32 KB flash, 4 KB SRAM, a full-speed USB 2.0 controller with on-chip transceiver, a low-power ARM Cortex-M0+ core, segment LCD controller (SLCD) option on related variants, multiple low-power modes (run, wait, stop, VLPRMPVLLS3), and a flexible low-power peripheral set including 12-bit ADC, 16-bit timers, LPUART, I2C, SPI, and USB. The device also integrates an internal 32 kHz and 8 MHz reference, simplifying BOM and supporting crystal-less USB operation in the KL2x sub-family.
Architecturally, the KL26 leverages Freescale/NXP's low-leakage process and a tightly coupled Cortex-M0+ pipeline with a single-cycle I/O port, achieving CoreMark/mW efficiency that puts it ahead of many 8-bit MCUs while retaining 32-bit throughput. The 48 MHz core mark, combined with hardware multiply/divide, gives roughly 0.93 DMIPS/MHz.
Typical applications include USB HID peripherals (keyboards, mice, remotes), wearable fitness bands, low-cost data loggers, sensor hubs, and battery-powered IoT end nodes. The on-chip USB 2.0 FS controller eliminates external PHY cost, and the 32 KB flash is adequate for HID class drivers, basic USB stacks, and small application logic.
When designing, note that the KL26 requires NXP's Kinetis Design Studio or MCUXpresso toolchain; an external decoupling scheme of 0.1 uF + bulk VHF per VDD/VREF domain is recommended, and the USB DP/DM traces must be 90 ohm differential matched.
This page synthesizes distributor pricing, drop-in pin-compatible Kinetis alternatives, and practical design notes beyond the manufacturer datasheet to help engineers make faster, more confident sourcing decisions.
Alternatif penggantian untuk MKL26Z32VLH4 — paket yang sama, pin-pada-pin kompatibel. Bagian paket yang berbeda memerlukan kerja ulang PCB diabaikan.
Variasi di dalam seri ini
Model-series yang sama yang kompatibel dengan penggantian MKL26Z32VLH4 (sama faktor bentuk dan footprint) — berbeda di dalam ADC, Core, Package, Communication Interfaces, Data Bus Width.
MKL26Z64VLH4
✅ Drop-In ⚠️ Spesifikasi Tidak Disahkan📋 Alternatif referensi (tidak dalam katalog)
MKL16Z32VLH4
✅ Drop-In ⚠️ Spesifikasi Tidak Disahkan📋 Alternatif referensi (tidak dalam katalog)
MKL24Z32VLH4
✅ Drop-In📋 Alternatif referensi (tidak dalam katalog)
MKL14Z32VLH4
✅ Drop-In📋 Alternatif referensi (tidak dalam katalog)
MKL26Z32VLH4 Rating Maksimal & Karakteristik Listrik
| Core | ARM Cortex-M0+ |
| Core Architecture | ARM 32-bit |
| Frekuensi Bawah Maximum | 48 MHz |
| Program Flash Memory | 32 KB (32K x 8) |
| RAM | 4 KB |
| USB Interface | USB 2.0 Full-Speed (OTG or Device, crystal-less option) |
| Paket | 64-pin LQFP (10 x 10 mm) |
| Pin/Package Suffix | VLH4 (LQFP-64) |
| Operating Voltage Range | 1.71 V to 3.6 V |
| Rentang Suhu Kerja | -40 C to +105 C |
| Low-Power Modes | Wait, Stop, VLPR, VLPW, VLPS, LLS, VLLS3 |
| ADC | 16-channel, 12-bit SAR |
| Timers | 2x 16-bit low-power timers; RTC |
| Communication Interfaces | LPUART, UART, SPI, I2C, USB |
| DMA Channels | 4 |
| GPIOs | Up to 51 |
| Tipe Mounting | Surface Mount |
| Status RoHS | Compliant |
| Lead-Free | Yes |
Konfigurasi Pin MKL26Z32VLH4
| Pin produk 1 | PTE0 — Port E bit 0; IRQ, ADC, TPM |
| Pin produk 2 | PTE1 — Port E bit 1; IRQ, ADC, TPM |
| Pin produk 3 | PTE2 — Port E bit 2; SPI, ADC |
| Pin produk 4 | PTE3 — Port E bit 3; SPI, ADC |
| Pin produk 5 | PTE4 — Port E bit 4; SPI, IRQ |
| Pin produk 6 | PTE5 — Port E bit 5; SPI, IRQ |
| Pin produk 7 | PTE6 — Port E bit 6; LPUART, I2C |
| Pin produk 8 | VDD — Digital supply voltage |
| Pin produk 9 | VSS — Ground |
| Pin produk 10 | USB_DP — USB D+ data line |
| Pin produk 11 | USB_DM — USB D- data line |
| Pin produk 12 | VREGIN — USB voltage regulator input |
| Pin produk 13 | VOUT33 — USB voltage regulator output (3.3 V) |
| Pin produk 14 | PTA0 — Port A bit 0; SWD CLK, IRQ |
| Pin produk 15 | PTA1 — Port A bit 1; SWD DIO, IRQ |
| Pin produk 16 | PTA2 — Port A bit 2; UART, TPM |
| Pin produk 17 | PTA3 — Port A bit 3; UART, TPM |
| Pin produk 18 | PTA4 — Port A bit 4; I2C, IRQ |
| Pin produk 19 | PTA5 — Port A bit 5; I2C, IRQ |
| Pin produk 20 | PTA6 — Port A bit 6; LPUART, IRQ |
| Pin produk 21 | PTA7 — Port A bit 7; LPUART, IRQ |
| Pin produk 22 | PTB0 — Port B bit 0; ADC, IRQ |
| Pin produk 23 | PTB1 — Port B bit 1; ADC, IRQ |
| Pin produk 24 | PTB2 — Port B bit 2; ADC, I2C |
| Pin produk 25 | PTB3 — Port B bit 3; ADC, I2C |
| Pin produk 26 | PTB4 — Port B bit 4; SPI, IRQ |
| Pin produk 27 | PTB5 — Port B bit 5; SPI, IRQ |
| Pin produk 28 | PTB6 — Port B bit 6; SPI, TPM |
| Pin produk 29 | PTB7 — Port B bit 7; SPI, TPM |
| Pin produk 30 | PTC0 — Port C bit 0; ADC, IRQ |
| Pin produk 31 | PTC1 — Port C bit 1; ADC, IRQ |
| Pin produk 32 | PTC2 — Port C bit 2; ADC, TPM |
| Pin produk 33 | PTC3 — Port C bit 3; ADC, TPM |
| Pin produk 34 | PTC4 — Port C bit 4; LPUART, IRQ |
| Pin produk 35 | PTC5 — Port C bit 5; LPUART, IRQ |
| Pin produk 36 | PTC6 — Port C bit 6; LPUART, TPM |
| Pin produk 37 | PTC7 — Port C bit 7; LPUART, TPM |
| Pin produk 38 | PTD0 — Port D bit 0; SPI, IRQ |
| Pin produk 39 | PTD1 — Port D bit 1; SPI, IRQ |
| Pin produk 40 | PTD2 — Port D bit 2; SPI, TPM |
| Pin produk 41 | PTD3 — Port D bit 3; SPI, TPM |
| Pin produk 42 | PTD4 — Port D bit 4; I2C, IRQ |
| Pin produk 43 | PTD5 — Port D bit 5; I2C, IRQ |
| Pin produk 44 | PTD6 — Port D bit 6; UART, TPM |
| Pin produk 45 | PTD7 — Port D bit 7; UART, TPM |
| Pin produk 46 | PTE16 — Port E bit 16; ADC, IRQ |
| Pin produk 47 | PTE17 — Port E bit 17; ADC, IRQ |
| Pin produk 48 | PTE18 — Port E bit 18; SPI, IRQ |
| Pin produk 49 | PTE19 — Port E bit 19; SPI, IRQ |
| Pin produk 50 | PTE20 — Port E bit 20; TPM |
| Pin produk 51 | PTE21 — Port E bit 21; TPM |
| Pin produk 52 | PTE22 — Port E bit 22; LPUART |
| Pin produk 53 | PTE23 — Port E bit 23; LPUART |
| Pin produk 54 | PTA8 — Port A bit 8; IRQ |
| Pin produk 55 | PTA9 — Port A bit 9; IRQ |
| Pin produk 56 | PTA10 — Port A bit 10; IRQ |
| Pin produk 57 | PTA11 — Port A bit 11; IRQ |
| Pin produk 58 | PTA12 — Port A bit 12; IRQ |
| Pin produk 59 | PTA13 — Port A bit 13; IRQ |
| Pin produk 60 | PTA14 — Port A bit 14; IRQ |
| Pin produk 61 | PTA15 — Port A bit 15; IRQ |
| Pin produk 62 | PTA16 — Port A bit 16; SPI, IRQ |
| Pin produk 63 | PTA17 — Port A bit 17; SPI, IRQ |
| Pin produk 64 | PTB8 — Port B bit 8; LPUART, IRQ |
Aplikasi Umum
MKL26Z32VLH4 cocok untuk 7 aplikasis: USB HID Peripherals (Keyboard, Mouse, Remote), Wearable Fitness Bands, Low-Cost Sensor Hubs and Data Loggers, USB Charging Cradles and Docks, Industrial HMI Panels, Battery-Powered IoT Edge Nodes, Educational and Maker Electronics.
USB HID Peripherals (Keyboard, Mouse, Remote)
The MKL26Z32VLH4's integrated USB 2.0 full-speed controller with on-chip PHY makes it a direct fit for USB HID class devices such as keyboards, mice, game controllers, and IR remotes. The 32 KB flash is sufficient to run the USB HID stack plus basic HID report descriptors and keymaps; the Cortex-M0+ at 48 MHz easily handles HID polling at 1 kHz with room for debounce and LED handling. Compared with MCUs that need an external USB PHY, the KL26 saves roughly $0.30-0.50 BOM and 4-6 mm board area. Designers typically route USB DP/DM as a 90 ohm differential pair and place a 0.1 uF + 4.7 uF decoupling network within 5 mm of VDD/VREF.
Direkomendasikan
Wearable Fitness Bands
For wearable fitness bands, the MKL26Z32VLH4's low-power modes (VLPR at <100 uA/MHz, VLLS3 standby sub-uA) and 1.71-3.6 V operation allow direct Li-ion or coin-cell powering. The Cortex-M0+ core at 48 MHz can sample a 3-axis accelerometer via I2C, drive an SPI OLED, and run step-count algorithms within tight power budgets. The 4 KB RAM is adequate for short sensor FIFO buffering, and the USB interface doubles as a charging and data-sync port, eliminating a separate charging IC. Trade-off: at 32 KB flash, designers must use lightweight RTOS or bare-metal; the MKL26Z64VLH4 drop-in upgrade doubles flash with no PCB rework if more headroom is needed.
Direkomendasikan
Low-Cost Sensor Hubs and Data Loggers
The MKL26Z32VLH4 serves well as a USB-tethered sensor hub, aggregating data from SPI/I2C sensors and streaming over USB CDC or HID to a host PC. Its 4-channel DMA offloads repetitive byte transfers, freeing the Cortex-M0+ core for time-stamping and threshold events. The 12-bit SAR ADC with up to 16 single-ended channels supports analog front-ends such as thermistors or load cells. A typical design reads sensors at 100 Hz, batches into 1 KB packets, and pushes over USB at FS rates - within both flash and MIPS budgets. Compared with 8-bit MCUs, the KL26 cuts code size 30-40% and adds deterministic 32-bit math for kalm filtering.
Direkomendasikan
USB Charging Cradles and Docks
In USB charging cradles and dock accessories, the MKL26Z32VLH4 acts as a USB device that negotiates charge current via USB BC 1.2 or proprietary protocols. The crystal-less USB option removes an external 12 MHz or 48 MHz crystal, reducing BOM and PCB area. The 32 KB flash supports USB stack plus application logic for battery authentication or LED status. The 51 GPIO lines can drive indicator LEDs, button input, and a charging FET. Trade-off: a charging cradle may not need the full Cortex-M0+ compute; a smaller MKL04Z can suffice, but the MKL26 is preferred when future firmware growth is anticipated.
Direkomendasikan
Industrial HMI Panels
For low-cost industrial HMI panels and operator interfaces, the MKL26Z32VLH4 drives character or segment LCDs, reads keypad matrices, and communicates to a master controller via RS-485 or CAN-isolated UART. The wide operating temperature range (-40 C to +105 C) is suitable for factory environments, and the 64-pin LQFP exposes enough GPIO to drive a 4x4 keypad plus 8 LEDs plus LCD. Designers typically pair the KL26 with an external RS-485 transceiver and a 5 V tolerant isolator. Compared with discrete logic designs, the KL26 cuts part count by 60% and adds firmware-driven diagnostics.
Direkomendasikan
Battery-Powered IoT Edge Nodes
In battery-powered IoT edge nodes (BLE/Wi-Fi sensor endpoints), the MKL26Z32VLH4 functions as the host MCU that drives a wireless co-processor via SPI/UART and manages sensors, power gating, and housekeeping. Its low-power modes (VLPS, LLS, VLLS3) extend coin-cell life to multi-year timeframes; the 32 KB flash fits BLE peripheral stacks or light Wi-Fi AT command logic. Compared with 8-bit MCUs at the same MIPS, the KL26 typically saves 20-40% energy per task due to single-cycle I/O and hardware multiply. Trade-off: very low duty-cycle nodes (<0.1%) may benefit from smaller MCUs, but the KL26's USB-charging option remains attractive for rechargeable nodes.
Direkomendasikan
Educational and Maker Electronics
The MKL26Z32VLH4, paired with the FRDM-KL26Z development board, is widely adopted in university embedded courses and maker projects because of its low cost, USB debugging, Arduino-friendly headers, and the free MCUXpresso IDE. The Cortex-M0+ introduces students to 32-bit ARM architectures without overwhelming complexity, while Kinetis peripheral libraries abstract low-level register access. Compared with Arduino Uno's ATmega328P, the KL26 offers 4x the flash, USB on-board, and a real IDE toolchain path. The 32 KB flash is suitable for typical semester projects (line-following robots, sensor dashboards, simple games).
Direkomendasikan
Ringkasan Produk Direkomendasikan
Data referensi engineering untuk MKL26Z32VLH4 — pembandingan, panduan desain, dan informasi konformitas.
Panduan Pemilihan
Pembandingan dengan Alternatif
| Parameter Umum | Produk Ini | MKL26Z64VLH4 | MKL16Z32VLH4 | MKL24Z32VLH4 | MKL14Z32VLH4 |
|---|---|---|---|---|---|
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Package | 64-pin LQFP (10x10 mm) | 64-pin LQFP (10x10 mm) - same | 64-pin LQFP (10x10 mm) - same | 64-pin LQFP (10x10 mm) - same | 64-pin LQFP (10x10 mm) - same |
| Core | ARM Cortex-M0+ | ARM Cortex-M0+ | ARM Cortex-M0+ | ARM Cortex-M0+ | ARM Cortex-M0+ |
| Max Clock Frequency | 48 MHz | 48 MHz | 48 MHz | 48 MHz | 48 MHz |
| Program Flash | 32 KB | 64 KB | 32 KB | 32 KB | 32 KB |
| USB Controller | USB 2.0 Full-Speed (with PHY) | USB 2.0 Full-Speed (with PHY) | No USB | No USB | No USB |
| Segment LCD Controller | No | No | No | Yes | No |
| RAM | 4 KB | 8 KB | 4 KB | 4 KB | 4 KB |
| Operating Voltage | 1.71 V to 3.6 V | 1.71 V to 3.6 V | 1.71 V to 3.6 V | 1.71 V to 3.6 V | 1.71 V to 3.6 V |
| Approx 1k+ Price (USD) | 2.98 | 3.40 | 2.75 | 3.10 | 2.60 |
Diferensiator Kunci
- Integrated USB 2.0 Full-Speed with on-chip PHY (vsMKL16Z32VLH4)
- Crystal-less USB option in KL2x sub-family (vsGeneric 48 MHz MCU)
- Segment LCD controller absent - choose KL24 for LCD designs (vsMKL24Z32VLH4)
- Cost-optimized 32 KB flash in 64-pin LQFP (vsMKL26Z128VLL4)
Catatan Desain
Decouple VDD/VREF/VREGIN with a 0.1 uF ceramic cap placed within 5 mm of each pin, plus a 4.7 uF bulk near the IC. For USB operation, add a 10 uF tantalum on VREGIN and a ferrite bead to VOUT33 to suppress USB inrush transients. The KL26's internal voltage regulator supplies the core from VREGIN; ensure VREGIN <= 5.5 V to avoid regulator damage.
Route USB DP/DM as a 90 ohm differential pair with length matching within 150 mil. Place the 33 ohm series resistors on DP/DM close to the MCU. Keep DP/DM traces away from clock lines and high-current switching nodes. Add ESD protection diodes (e.g. USBLC6-2SC6) near the USB connector. Maintain a continuous ground plane under the KL26 and stitch with vias around the LQFP perimeter.
Estimated: at 48 MHz core clock, the KL26 typically dissipates ~25 mW active and <50 uA in VLLS3 mode. The 64-pin LQFP package has theta_JA around 60 C/W, so a 25 mW load produces ~1.5 C junction rise - no heatsink needed. In VLPR mode (4 MHz), active current drops to ~3 mA; in VLLS3, standby is sub-uA, suitable for coin-cell applications.
Do not omit the external 32.768 kHz crystal load capacitors (typically 12.5 pF) on XTAL32/EXTAL32 pins if RTC accuracy matters; otherwise use the internal reference. When enabling the internal USB regulator (VREGIN path), ensure VOUT33 is not loaded with >3 mA externally. For SWD debugging, keep the SWD_CLK and SWD_DIO traces < 50 mm and avoid stubs. Do not float unused GPIO to avoid leakage in low-power modes.
Place the KL26 such that the LQFP pin 1 dot/orientation matches the schematic. Keep the 32.768 kHz crystal traces short and symmetric. Route analog ADC inputs (PTA, PTB, PTC, PTE) away from digital switching lines and bypass each analog pin with 100 nF to VREFH when used. For USB VBUS sensing, the VREGIN pin doubles as a VBUS presence detector; route this signal cleanly to avoid false disconnect events.
Informasi Konformitas
RoHS compliant per NXP product page. Halogen-free per datasheet. AEC-Q100 not qualified - industrial / consumer grade. Lead-free reflow compatible.
