Texas Instruments

PCA9557RGVR - 8-Bit I2C I/O Expander | Texas Instruments

MPN: PCA9557RGVR ✓ Aktif
2.3 V to 5.5 V Vdss 16-pin VQFN (RGV) Package 400 kHz Speed
MOQ: 1 |

PCA9557RGVR Ringkasan

Texas Instruments PCA9557RGVR is an 8-bit I2C and SMBus low-power I/O expander with reset and configuration registers. It operates from 2.3 V to 5.5 V, supports I2C and SMBus communication at 400 kHz, and is packaged in a 16-pin 4 x 4 mm VQFN designated RGV. The device provides eight remotely controlled I/O lines while allowing a host controller to monitor and control additional peripherals over a serial bus.

An I/O expander is an interface IC that extends the number of general-purpose inputs and outputs available to a microcontroller or other bus controller. Its place in the hierarchy is I/O expander, interface IC, integrated circuit, and semiconductor. Instead of dedicating multiple host pins to discrete control functions, a system can use the PCA9557RGVR to bring eight additional lines onto a shared two-wire bus. This can simplify routing and conserve host-controller I/O resources.

The principal device features include an 8-bit I/O port, a 400 kHz I2C/SMBus interface, a 2.3 V to 5.5 V operating range, and dedicated reset and configuration registers. The reset function supports deterministic initialization of the port state, while the configuration registers allow the host software to define whether each port line operates as an input or output. These functions make the device useful in embedded systems where firmware must establish controlled states before external circuitry is enabled.

The PCA9557RGVR is intended for low-power remote I/O expansion over an embedded serial bus. Its eight programmable lines can represent simple digital status inputs, control outputs, or a mixture of both. The 400 kHz bus rate provides a practical communication rate for many control systems while avoiding the wiring complexity of connecting eight separate host GPIO pins. The 2.3 V minimum operating voltage also places the device within the range commonly used by embedded processors and industrial controllers.

Typical uses include industrial control panels, sensor and alarm interfaces, LED and relay control, compact embedded modules, and general-purpose controller expansion. In each case, the host communicates through I2C or SMBus and reads or writes the device registers. System software should define port directions, initialize outputs to a safe state, and use the reset input where deterministic startup behavior is required.

Design consideration: place the PCA9557RGVR close to the connectors and peripherals it controls to keep I/O traces short, while routing the I2C bus with appropriate pull-up arrangements. Account for the device's 5.5 V maximum operating voltage and ensure that connected peripherals cannot back-power the port lines during reset. Firmware must also preserve the configured operating state whenever a reset is initiated.

This product page combines the manufacturer's exact orderable-part information with practical guidance on reset handling, bus implementation, port configuration, PCB placement, and drop-in replacement evaluation. It helps engineers identify the correct 4 x 4 mm RGV package, verify the operating range and bus speed, and compare the available substitution evidence before committing to a design.

Alternatif penggantian untuk PCA9557RGVR — paket yang sama, pin-pada-pin kompatibel. Bagian paket yang berbeda memerlukan kerja ulang PCB diabaikan.

Tidak ada alternatif pengganti yang tersedia untuk produk ini.

Permintaan Alternatif

PCA9557RGVR Spesifikasi

Device Type 8-bit I2C/SMBus low-power I/O expander
Number of I/O Lines 8 lines
Operating Voltage Range 2.3 V to 5.5 V
Bus Interface I2C and SMBus
Maximum Bus Frequency 400 kHz
Register Functions Reset and configuration registers
Package Type 16-pin VQFN (RGV)
Package Dimensions 4 mm x 4 mm
Package Pin Count 16 pins
Rentang Suhu Kerja -40 C to +85 C
Tipe Mounting Surface mount

PCA9557RGVR 16 pins Diamant Konfigurasi Panduan

Konfigurasi pin untuk PCA9557RGVR (16 pins pakai pakai). Penomoran pin, fungsi, dan diagram koneksi ditetapkan dalam datasheet produsen. Lihatnya untuk footprint dan pedoman perpindahan paruh.

Diamant diagram pakai pakai 16 pins untuk PCA9557RGVR

Tidak ada data diatribut pin yang tersedia untuk PCA9557RGVR.

Lihat ke: datasheet produk untuk konfigurasi pin penuh.

Aplikasi Umum

PCA9557RGVR cocok untuk 6 aplikasis: Industrial Control Panel Status Expansion, Sensor and Alarm Input Interface, LED and Indicator Control, Relay and Discrete Control Interface, Embedded Module Port Expansion, Low-Power Sensor Hub Interface.

🏭

Industrial Control Panel Status Expansion

The PCA9557RGVR suits industrial control panels that need more digital status and command lines than the host controller can expose directly. Its eight I/O channels operate from 2.3 V to 5.5 V and communicate through I2C or SMBus at up to 400 kHz, allowing a single bus to connect the panel interface. Configure selected lines as inputs for limit switches, interlocks, or module status and the others as outputs for indicators and control signals. The -40 C to +85 C operating range provides a useful fit for many industrial environments, although the final system must still satisfy its enclosure, surge, and EMC requirements.

🧩

Sensor and Alarm Input Interface

The PCA9557RGVR can consolidate several discrete alarms or sensor contacts into a compact controller interface. Eight configurable I/O lines allow inputs to report door, fault, presence, or threshold events through the host's I2C or SMBus connection, with communication supported to 400 kHz. The reset input and configuration registers help software establish predictable line states during initialization. Keep sensing wiring away from switching nodes, use suitable protection for long cables, and confirm the port voltage limits before applying external signals.

💡

LED and Indicator Control

Eight outputs from the PCA9557RGVR can drive simple status LEDs or indicator stages in embedded equipment. The 2.3 V to 5.5 V operating range accommodates common embedded supply rails, while the 400 kHz interface permits prompt status updates without tying up separate host GPIO pins. Software can use the configuration registers to establish which channels are outputs and can control them through the port register. For indicators requiring more current, use a suitable transistor or driver stage and verify the PCA9557RGVR pin limits before connecting the load.

⚡

Relay and Discrete Control Interface

The PCA9557RGVR provides a convenient low-speed command interface for relays, contactors, and other discrete actuators managed by a host controller. Eight outputs reduce the number of direct host-controller connections while retaining programmable input or output direction through the configuration registers. The I2C/SMBus interface operates up to 400 kHz, which is suitable for control updates rather than high-speed signaling. Relay coils and other inductive loads should use appropriate driver, flyback, isolation, and grounding arrangements rather than relying on the expander alone.

🖥️

Embedded Module Port Expansion

PCA9557RGVR is useful when a compact embedded module must expose additional digital lines without increasing the host processor's pin count. Its 16-pin, 4 x 4 mm RGV VQFN preserves board area compared with larger through-hole or high-count packages, while the 2.3 V to 5.5 V range supports common processor rails. The bus implementation can share I2C with other compatible peripherals at 400 kHz. Address management, pull-up selection, startup behavior, and port-state initialization must be coordinated with the module's master firmware.

📡

Low-Power Sensor Hub Interface

The PCA9557RGVR can add discrete digital controls to a compact sensor hub that communicates through I2C or SMBus. Its eight configurable lines can accept threshold or presence signals and provide limited output control, helping the hub avoid dedicating processor pins to simple functions. The 400 kHz bus rate accommodates routine monitoring and configuration traffic, and the 2.3 V to 5.5 V range offers flexibility across embedded systems. Firmware should group transactions efficiently, avoid unnecessary polling, and confirm that the sensor hub supports the required bus voltage and addressing scheme.

What is the operating voltage of PCA9557RGVR?
The PCA9557RGVR operates from 2.3 V to 5.5 V. According to the Texas Instruments product page, this range applies to the complete PCA9557 device family and includes the orderable PCA9557RGVR configuration. The operating range is important when the device is connected to a 3.3 V or 5 V embedded system. Designers should verify that every externally connected port signal remains within the limits defined by the manufacturer datasheet, particularly during reset and power sequencing.
What is PCA9557RGVR and what does it do?
The PCA9557RGVR is an 8-bit I2C and SMBus low-power I/O expander with reset and configuration registers. According to the Texas Instruments product page, it adds eight programmable I/O lines to a host controller through a two-wire serial interface. Each port line can be configured for digital input or output operation, allowing the device to expand control and status signaling without consuming eight dedicated GPIO pins on the host microcontroller.
How many I/O ports does PCA9557RGVR provide?
The PCA9557RGVR provides eight I/O lines. According to the Texas Instruments product page, the device is an 8-bit I2C/SMBus I/O expander with reset and configuration registers. The eight lines can be configured individually through the device's configuration registers, allowing a mixture of inputs and outputs in one component. This makes the part useful for control panels, status inputs, discrete output controls, and other compact embedded-control arrangements.
What is the maximum I2C bus speed of PCA9557RGVR?
The PCA9557RGVR supports a maximum I2C/SMBus frequency of 400 kHz. According to the Texas Instruments orderable-part listing, the device is specified as an 8-channel I2C and SMBus I/O expander rated to 400 kHz. Actual bus timing still depends on the complete circuit, including pull-up resistance, bus capacitance, clock rise time, voltage level, and firmware behavior. Verify the final bus design against the manufacturer timing characteristics.
Where can I download the PCA9557RGVR datasheet?
The official PCA9557RGVR documentation begins on the Texas Instruments PCA9557 product page at https://www.ti.com/product/PCA9557. The orderable-part details are available at https://www.ti.com/product/PCA9557/part-details/PCA9557RGVR. Use the manufacturer's datasheet for the complete pin descriptions, register map, timing diagrams, electrical characteristics, and application guidance. Third-party PDF mirrors can assist with viewing, but the manufacturer document should remain the controlling source for design decisions.
Where can I find the PCA9557RGVR pinout?
The PCA9557RGVR pinout is published in the manufacturer datasheet for the 16-pin RGV package. Texas Instruments identifies the orderable part as a 16-pin VQFN in the RGV package, so engineers should use the pin-description table and package drawing for the exact RGV footprint. Do not substitute a pin arrangement from another package or family member without checking every numbered terminal and exposed-pad connection before laying out or modifying a PCB.
Does PCA9557RGVR support SMBus as well as I2C?
Yes, the PCA9557RGVR supports both I2C and SMBus communication. According to the Texas Instruments product page, the PCA9557 is an I2C/SMBus I/O expander with a maximum bus frequency of 400 kHz. The interface allows the eight port lines to be managed by a host controller over a shared bus. Firmware must handle the device's register addresses, port directions, reset behavior, and any bus timeout or recovery sequence required by the surrounding system.
What are the key specifications of PCA9557RGVR that engineers should know?
The PCA9557RGVR is a 16-pin, 4 x 4 mm RGV VQFN that expands a host bus with eight programmable I/O lines. Texas Instruments specifies a 2.3 V to 5.5 V operating range, I2C and SMBus support, and a maximum bus rate of 400 kHz. Reset and configuration registers are included for controlled startup and port-direction setup. These are the primary order-selection and circuit-integration parameters for this exact package and suffix.
Can PCA9557RGVR be used for LED and relay control?
Yes, PCA9557RGVR can provide host-controlled outputs for LEDs, relays, and other digital actuators. The eight port lines are configured through the device's configuration registers, while the host communicates over I2C or SMBus. The 400 kHz bus rate is appropriate for many low- and medium-update-rate control systems. Before connecting an inductive or high-current load, verify the port drive limits and add suitable driver, protection, and isolation circuitry where required.
PCA9557RGVR vs PCA9557RGYR: is the smaller package a drop-in replacement?
No—the PCA9557RGVR and PCA9557RGYR do not provide the same package footprint for a literal drop-in substitution. The manufacturer listings identify PCA9557RGVR as a 16-VQFN measuring 4 x 4 mm, while PCA9557RGYR is identified as a 16-VQFN measuring 4 x 3.5 mm. The similar family name and pin count do not overcome the dimensional difference. Use the exact package drawing and compare every terminal position before considering a board-level replacement.
What is the best drop-in replacement for PCA9557RGVR?
No verified drop-in replacement for PCA9557RGVR was established in the available cross-reference results. The PCA9557RGYR is a related 16-pin family member, but its 4 x 3.5 mm VQFN package differs from the PCA9557RGVR's 4 x 4 mm package and therefore is not a same-footprint replacement. Use the Texas Instruments cross-reference search and manufacturer pin documentation to validate any proposed substitute for voltage, address, register behavior, reset, and mechanical compatibility.
When should I choose PCA9557RGVR instead of a larger I/O expander?
Choose PCA9557RGVR when the design needs a compact eight-line I2C/SMBus expansion solution within a 2.3 V to 5.5 V system range. Its 16-pin, 4 x 4 mm RGV package is useful where PCB area is constrained, while reset and configuration registers support deterministic initialization. Consider a larger expander when more lines, higher bus rates, wider voltage options, more registers, or stronger output-drive capability are required. Compare the required register and electrical features rather than port count alone.
Is PCA9557RGVR suitable for industrial control-panel applications?
PCA9557RGVR is suitable for industrial control-panel designs that require a small number of low-speed digital I/O lines and operate within 2.3 V to 5.5 V. The manufacturer specifies an operating temperature range of -40 C to +85 C for this orderable part, which covers many industrial environments. System qualification still depends on the complete product, including its enclosure, voltage transients, electromagnetic requirements, component sourcing, and applicable industry regulations.
How should reset be handled in a PCA9557RGVR circuit?
Use the reset function to place the PCA9557RGVR into a known initialization condition before enabling connected external hardware. According to the Texas Instruments product description, reset and configuration registers are standard features of the device. Firmware should configure each port as input or output and establish safe output values before releasing downstream loads. The reset circuit and timing requirements must follow the manufacturer datasheet, especially when reset is shared with other system devices.
Where to buy PCA9557RGVR and what is its current lead time?
Use the Request a Quote form on this page to request PCA9557RGVR availability, current lead time, order quantity, and shipment options. The available distributor search results confirm the exact orderable MPN and its Texas Instruments origin, but they do not print a qualifying quantity-break price table for this exact suffix. XAIPART therefore does not publish a static price, price tier, or assumed stock status on this product page.

Data referensi engineering untuk PCA9557RGVR — pembandingan, panduan desain, dan informasi konformitas.

Panduan Pemilihan

Choose PCA9557RGVR when a design needs eight configurable digital I/O lines, I2C/SMBus communication up to 400 kHz, and a compact 16-pin, 4 x 4 mm RGV VQFN. It is particularly appropriate for control panels, status-input modules, indicator control, and embedded systems operating from 2.3 V to 5.5 V with -40 C to +85 C temperature requirements. The related PCA9557RGYR should not be treated as a literal drop-in replacement because its 4 x 3.5 mm package differs from the 4 x 4 mm PCA9557RGVR footprint. Select a different expander when the design requires more than eight lines, a different I2C address arrangement, higher bus rates, wider voltage options, stronger output drive, or a different reset architecture. Before releasing a new PCB, confirm the complete pinout, register map, timing limits, address, port-current ratings, and exposed-pad requirements in the Texas Instruments datasheet.

Pembandingan dengan Alternatif

Parameter Umum Produk Ini
Brand Texas Instruments
Package 16-VQFN (RGV), 4 mm x 4 mm
Device Type 8-bit I2C/SMBus low-power I/O expander
Operating Voltage Range 2.3 V to 5.5 V
Maximum Bus Frequency 400 kHz
Number of I/O Lines 8
Operating Temperature Range -40 C to +85 C
Special Functions Reset and configuration registers

Diferensiator Kunci

  • Compact eight-line expansion in the specified 4 x 4 mm package (vsPCA9557RGYR)
  • Established dual-bus interface (vsPCA9557RGYR)
  • Broad embedded operating range (vsPCA9557RGYR)

Catatan Desain

Place the PCA9557RGVR near the connectors and remote I/O circuitry it serves to minimize exposed trace length and susceptibility to noise. Keep the I2C or SMBus route away from switching-power and high-current actuator paths. The manufacturer identifies a 16-pin, 4 x 4 mm RGV VQFN package, so the land pattern must follow that exact package drawing. Confirm exposed-pad, thermal-pad, and solder-mask requirements in the manufacturer land-pattern guidance before fabrication.

Do not assume that a related family member with the same pin count is a mechanical drop-in replacement. PCA9557RGYR uses a 4 x 3.5 mm VQFN according to its manufacturer listing, while PCA9557RGVR uses a 4 x 4 mm package. Before substitution, compare package drawings, terminal numbering, exposed-pad connections, I2C addresses, reset behavior, configuration registers, and electrical limits. A PCB redesign may be required even when the component family and functional description are similar.

Design the I2C/SMBus network for the 400 kHz maximum rate rather than assuming every bus will operate at that rate. Select pull-up resistance using the actual bus voltage, total capacitance, clock rise time, sink-current limits, and the number of connected devices. The PCA9557RGVR supports I2C and SMBus, but the complete bus must still satisfy timing and drive limits. Keep traces short, use continuous ground reference, and account for pull-up current in the host supply budget.

Initialize the eight PCA9557RGVR port lines before enabling connected loads so external circuitry is not driven into an unintended state during power-up or reset. Use the configuration registers to establish input or output direction and write safe output values as part of the startup sequence. Because reset behavior and external back-power paths can affect the port state, follow the manufacturer timing diagram and isolate external circuits when required. Do not exceed the stated 5.5 V maximum operating voltage.

Choose the PCA9557RGVR suffix only after checking mechanical requirements for the 4 x 4 mm RGV package and electrical requirements for the 2.3 V to 5.5 V system range. PCA9557RGYR is a 4 x 3.5 mm package variant and is therefore not a same-footprint substitute. Also verify the device's fixed I2C address and any system-level address-management scheme before finalizing a multi-expander bus. Use the manufacturer datasheet for address, pin, timing, and current-limit details.

Informasi Konformitas

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Bebas Logam Lengket
Unknown
Bebas Halogena
Unknown
Mineral Konflik
Unknown

The manufacturer product and orderable-part pages do not state the requested environmental, halogen-free, conflict-minerals, or automotive-qualification status for this exact orderable part. AEC-Q100 is not applicable because no automotive qualification is documented.

Data disahkan pada: 2026-11-10 — data disahkan dan disusun oleh tim engineering komponen XAIPART

Pencarian Terkait

PCA9557RGVR datasheet PCA9557RGVR pinout PCA9557RGVR datasheet pdf PCA9557RGVR equivalent PCA9557RGVR replacement PCA9557RGVR cross reference PCA9557RGVR footprint PCA9557RGVR price PCA9557RGVR stock Texas Instruments PCA9557RGVR PCA9557RGVR RGV pinout PCA9557RGVR I2C application circuit PCA9557RGVR vs PCA9557RGYR PCA9557 8-bit I2C expander

Komponen dan Istilah Terkait

Texas Instruments PCA9557 PCA9557RGVR PCA9557RGYR I/O expander interface IC integrated circuit semiconductor I2C SMBus 8-bit parallel port 400 kHz bus 2.3 V minimum operating voltage 5.5 V maximum operating voltage configuration register reset register VQFN RGV package 16-pin VQFN surface-mount package industrial control panel sensor interface LED control relay control
Kutipan Cepat RFQ
Isi detail lengkap — tim penjualan kami akan membalas dalam 24 jam
Nomor Part Manufaktur Paket QTY Harga Target Lengkap
✓
Kutipan telah disubmit!

Kami akan membalas email Anda dalam 24 jam

1
RFQ Dikirim
2
Kutipan Diterima
3
Order Ditempatkan
4
Pembayaran
5
Dikirim
6
Dikirim
Lihat Detil RFQ