PIC10F322-E/OT - 16MHz 8-Bit MCU | Microchip Technology
MPN: PIC10F322-E/OT ✓ AktifPIC10F322-E/OT Ringkasan
A microcontroller is a programmable integrated circuit containing a CPU core, memory, I/O ports, and peripherals. The PIC10F322 belongs to the PIC10F family of small 8-bit RISC microcontrollers and fits within the broader embedded-processing and semiconductor hierarchy. Its small package and integrated analog conversion allow control, measurement, and actuator functions to be consolidated onto a compact circuit board.
Key device features include 16 MHz maximum operating speed, 896 bytes of flash program memory, 64 bytes of data RAM, four general-purpose I/O pins, and an 8-bit ADC. The family data sheet also identifies Timer0, Timer2, configurable logic, PWM modules, brown-out detection, power-on reset, and a watchdog timer. These peripherals reduce the need for external components in simple sensing, timing, and output-control applications.
The PIC10F322 architecture is designed around the compact PIC10F core and its configurable logic cells. The ADC provides a simple interface for analog inputs, while the timer and PWM blocks support periodic events, motor or LED drive, and basic waveform generation. Configurable logic can implement additional digital conditions locally, reducing firmware overhead in compact control systems where the application requires deterministic response to several I/O signals.
Typical uses include battery-powered sensors, temperature and industrial monitoring nodes, LED indicators, compact motor controls, appliance interfaces, and general-purpose embedded control. The 2.3 V to 5.5 V supply range supports both 3.3 V and 5 V system architectures. Designers should confirm the ADC, timer, and pin requirements against the device configuration before finalizing a PCB because the PIC10F320 and PIC10F322 offer different peripheral combinations within the same family.
For PCB design, use the manufacturer's SOT-23-6 footprint and pin-description table when assigning tracks. Place the decoupling capacitor close to VDD and GND, route sensitive analog inputs away from fast-switching nodes, and provide adequate copper and via patterns around the device. Firmware should also account for the difference between the -E and -I temperature-grade options when selecting a replacement.
This page combines manufacturer specifications, family-level cross-reference information, package and pinout resources, replacement guidance, application-specific design advice, and structured comparisons. It is intended to help engineers evaluate the PIC10F322-E/OT for new designs, verify PCB compatibility, and determine whether another member of the PIC10F320 and PIC10F322 family is a more appropriate device.
Alternatif penggantian untuk PIC10F322-E/OT — paket yang sama, pin-pada-pin kompatibel. Bagian paket yang berbeda memerlukan kerja ulang PCB diabaikan.
Variasi di dalam seri ini
Model-series yang sama yang kompatibel dengan penggantian PIC10F322-E/OT (sama faktor bentuk dan footprint) — berbeda di dalam ADC, Package, I/O Pins, MSL Level, Program Memory (Flash).
PIC10F322T-E/OT
✅ Drop-In📋 Alternatif referensi (tidak dalam katalog)
PIC10F322T-I/OT
✅ Drop-In📋 Alternatif referensi (tidak dalam katalog)
PIC10LF322T-E/OT
✅ Drop-In📋 Alternatif referensi (tidak dalam katalog)
PIC10LF322T-I/OT
✅ Drop-InKontak untuk harga
Lihat Datasheet →PIC10F320T-E/OT
✅ Drop-InKontak untuk harga
Lihat Datasheet →PIC10F320T-I/OT
✅ Drop-In📋 Alternatif referensi (tidak dalam katalog)
PIC10F322-E/OT Rating Maksimal & Karakteristik Listrik
| Product Type | 8-bit flash microcontroller |
| Frekuensi Bawah Maximum | 16 MHz |
| Program Memory | 896 bytes flash (512 x 14) |
| Data Memory | 64 bytes RAM |
| General-Purpose I/O | 4 pins |
| ADC Resolution | 8 bits |
| Operating Voltage Range | 2.3 V to 5.5 V |
| Architecture | 8-bit PIC RISC core |
| Timer0 | 8-bit timer/counter with 8-bit programmable prescaler |
| Timer2 | 8-bit timer/counter with 8-bit period register, prescaler, and postscaler |
| PWM | Two PWM modules, 10-bit resolution |
| Configurable Logic | Integrated configurable logic cells |
| Brown-Out Detection | Yes |
| Watchdog Timer | Yes |
| Paket | 6-pin SOT-23 |
| Tipe Mounting | Surface mount |
| Operating Temperature Grade | Extended temperature grade |
PIC10F322-E/OT 6-pin sot-23 Diamant Konfigurasi Panduan
Konfigurasi pin untuk PIC10F322-E/OT (6-pin sot-23 pakai pakai). IC digital ini termasuk GPIO, antarmuka komunikasi (UART, SPI, I2C), dan pin kuasa. Lihat datasheet produsen untuk fungsi pin alternatif dan opsi konfigurasi. Penting untuk desain sistem pengemasan dan PCB.
Tidak ada data diatribut pin yang tersedia untuk PIC10F322-E/OT.
Lihat ke: datasheet produk untuk konfigurasi pin penuh.
Aplikasi Umum
PIC10F322-E/OT cocok untuk 6 aplikasis: Battery-Powered Sensor Node, Industrial Condition Monitoring, LED Indicator and Lighting Control, Compact Motor and Actuator Control, Appliance Interface Controller, Portable Measurement Instrument.
Battery-Powered Sensor Node
The PIC10F322-E/OT fits compact battery-powered sensor nodes because it combines a 16 MHz processor, 896 bytes of flash, 64 bytes of RAM, and an 8-bit ADC in a 6-pin SOT-23 package. The ADC can digitize a resistive or active sensor signal, while four I/O pins support a switch, status indicator, or alert output. Its 2.3 V to 5.5 V range accommodates common 3.3 V sensor architectures. Firmware can use Timer0 or Timer2 for periodic sampling and the watchdog timer for recovery, although battery life must be evaluated using the complete sensor, regulator, and communication load rather than MCU current alone.
Direkomendasikan
Industrial Condition Monitoring
A PIC10F322-E/OT can form the compact control section of an industrial condition-monitoring module. The 8-bit ADC accepts a conditioned analog sensor, while configurable logic and interrupt-on-change capabilities can monitor switch or threshold inputs. Its 16 MHz operating speed provides sufficient timing headroom for periodic measurements, filtering, and local status handling without a larger microcontroller package. The 2.3 V to 5.5 V operating range supports both 3.3 V industrial sensor interfaces and 5 V control logic. For factory deployments, engineers should verify the -E temperature limits, isolate long cable runs, and place filtering close to the analog input to avoid converting external noise into ADC readings.
Direkomendasikan
LED Indicator and Lighting Control
The PIC10F322-E/OT is suitable for simple LED indication, status sequencing, and low-power lighting control. Its two 10-bit PWM modules can generate a duty cycle for dimming or blinking, while Timer0 and Timer2 provide independently scheduled events. Four I/O pins leave room for pushbuttons, indicator outputs, and a sensor input, and the integrated 8-bit ADC can monitor a light-dependent or current-sense condition. The 6-pin SOT-23 package reduces board area in compact appliance controls. Designers should confirm that the chosen 6-pin device exposes the required PWM outputs and check the device's output-drive limits against the LED current before adding a transistor or resistor network.
Direkomendasikan
Compact Motor and Actuator Control
The PIC10F322-E/OT can control small motors, solenoids, relays, or actuators where a dedicated motor-driver IC is unnecessary. The PIC10F family includes PWM generation and configurable logic, allowing the MCU to create timing pulses and combine output conditions in a compact 6-pin footprint. The 8-bit ADC can monitor a potentiometer, current signal, or temperature-derived analog input for closed-loop behavior. At 16 MHz, the processor can execute control logic and state-machine updates without a larger embedded platform. Keep the MCU away from motor wiring, use a separate protection and driver path for inductive loads, and validate that the SOT-23-6 variant provides every required timer and PWM output.
Direkomendasikan
Appliance Interface Controller
In a small appliance or kitchen device, the PIC10F322-E/OT can supervise buttons, indicators, a low-cost analog sensor, and a simple timed output. The 896-byte flash and 64-byte RAM are suitable for focused control firmware rather than a large user interface, while the four I/O pins can support input detection and direct output control. The 2.3 V to 5.5 V range allows operation from either 3.3 V or 5 V subsystems. Configurable logic can assist with debouncing or simple interlock conditions, while PWM can regulate an LED or low-power actuator. The design must be checked against the appliance's electrical-noise environment, including separation from mains-derived switching stages and the need for appropriate protective components.
Direkomendasikan
Portable Measurement Instrument
The PIC10F322-E/OT can serve as the control MCU in a portable measurement or calibration instrument built around one or two analog inputs. Its 8-bit ADC performs digitizing, while Timer0 and Timer2 organize periodic sampling, timeouts, and output updates. The 6-pin SOT-23 footprint leaves board area for a display interface, precision reference, or communications hardware, and the processor's 16 MHz speed supports responsive control calculations. For battery-operated instruments, duty-cycle the ADC and peripherals to reduce average consumption, and use the watchdog timer to recover from unexpected states. Accuracy also depends on the external reference and analog signal-conditioning network rather than ADC resolution alone.
Direkomendasikan
Ringkasan Produk Direkomendasikan
Data referensi engineering untuk PIC10F322-E/OT — pembandingan, panduan desain, dan informasi konformitas.
Panduan Pemilihan
Pembandingan dengan Alternatif
| Parameter Umum | Produk Ini | PIC10F322T-E/OT | PIC10F322T-I/OT | PIC10LF322T-E/OT | PIC10LF322T-I/OT | PIC10F320T-E/OT |
|---|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | SOT-23-6 | SOT-23-6 - same | SOT-23-6 - same | SOT-23-6 - same | SOT-23-6 - same | SOT-23-6 - same |
| Core Architecture | 8-bit PIC RISC | 8-bit PIC RISC | 8-bit PIC RISC | 8-bit PIC RISC | 8-bit PIC RISC | 8-bit PIC RISC |
| Maximum Clock Frequency | 16 MHz | 16 MHz | 16 MHz | 16 MHz | 16 MHz | 16 MHz |
| Temperature Grade | -E extended grade | -E extended grade | -I grade | -E extended grade | -I grade | -E extended grade |
Diferensiator Kunci
- Combines an 8-bit ADC with configurable logic in a compact 6-pin package (vsPIC10F320T-E/OT)
- Supports both 3.3 V and 5 V system architectures (vsPIC10LF322T-E/OT)
- Extended-temperature ordering option for industrial environments (vsPIC10F322T-I/OT)
- Matches the PIC10F322 family core and memory configuration (vsPIC10F322T-E/OT)
Catatan Desain
Place the device-level bypass capacitor immediately between the VDD and GND pins, with the shortest practical return path. Route analog inputs away from PWM outputs, relay drivers, and switching-power nodes to reduce conversion noise. Because the family is offered in 6-pin and 8-pin packages, use only the package-specific land pattern and pin-description table rather than a generic six-pin SOT-23 footprint.
Maintain the operating supply between 2.3 V and 5.5 V under startup, load transients, and brown-out conditions. The PIC10F322 includes power-on reset and brown-out detection, but those functions do not replace correct supply design. For battery applications, estimate average consumption from processor run time, ADC use, timers, pull resistors, and external sensors. Select a regulator whose startup behavior does not cause the MCU supply to leave its specified range.
Do not treat every PIC10F320, PIC10F322, or PIC10LF322 ordering code as interchangeable. The target uses 896 bytes of flash, 64 bytes of RAM, four I/O pins, and an 8-bit ADC, while related devices can differ in voltage range, peripheral set, temperature grade, and pin multiplexing. Before substitution, compare the device-selection table, electrical limits, and SOT-23-6 pin descriptions, then rebuild the firmware for the replacement configuration.
For analog measurement, keep the sensor and conditioning network close to the ADC input and return analog ground through a controlled path. Sample when the signal is stable, use averaging or filtering in firmware, and avoid using the same switching node as the ADC reference. The 8-bit converter can support coarse control and monitoring, but calibration and reference stability determine practical measurement accuracy more than nominal resolution alone.
The small SOT-23-6 package is appropriate for low-power control, but its thermal capacity is limited. Keep continuous switching activity and high-current output drive away from the device when possible, provide copper around the package without compromising clean analog routing, and calculate the worst-case ambient temperature. The -E suffix denotes the extended-temperature selection, while the exact numerical limits should be taken from the manufacturer ordering information.
Informasi Konformitas
RoHS, REACH, lead-free, halogen-free, and conflict-minerals status require confirmation for the exact ordering code through the manufacturer product documentation.