PIC16LC77-04/L - 8-bit 4MHz 14KB OTP MCU 44-PLCC | Microchip
MPN: PIC16LC77-04/L ✓ AktifPIC16LC77-04/L Ringkasan
An 8-bit microcontroller (MCU) is a single-chip computer that integrates a CPU, program memory (ROM/OTP/Flash), data memory (RAM), and peripherals onto a single silicon die. The PIC architecture uses a Harvard structure with separate program and data buses, which allows instruction words to differ in width from the 8-bit data word and improves instruction throughput compared with von Neumann designs. Within Microchip's portfolio, the PIC16C family sits between the baseline PIC10/12/16 and the high-performance PIC17/PIC18 series, targeting cost-sensitive industrial and consumer applications that need A/D conversion and moderate I/O counts.
The PIC16LC77-04/L integrates an 8-channel 8-bit A/D converter, USART, SPI/I2C-compatible synchronous serial port, capture/compare/PWM modules, and a watchdog timer. The "LC" suffix indicates the low-voltage CMOS process, enabling operation down to 2.5 V for battery-powered designs, while the "-04" speed grade denotes the 4 MHz oscillator limit. With 368 bytes of RAM and an instruction set optimized for single-word single-cycle execution, the part delivers deterministic interrupt response suitable for real-time control loops.
Architecturally, the device uses a 14-bit wide program memory word with 35 instructions, allowing most operations to complete in a single instruction cycle (4 oscillator clocks). This RISC-style design yields an instruction throughput of 1 MIPS at 4 MHz, balanced against the 14 KB code ceiling for mid-sized firmware projects. The OTP memory means firmware is programmed during manufacturing and cannot be updated in the field.
Typical applications include industrial motor control, automotive body electronics, appliance control boards, smart sensors, and low-power instrumentation. The wide operating voltage and rich peripheral mix also suit battery-backed data loggers and legacy equipment retrofits.
When designing with this OTP part, plan code space carefully because firmware cannot be re-programmed in the field. Use the Microchip MPLAB ICD or PRO MATE device programmer during development and reserve adequate decoupling (0.1 uF plus bulk) near the VDD pins.
This page synthesizes distributor pricing, drop-in same-family alternatives, and practical design notes that complement the Microchip datasheet.
Alternatif penggantian untuk PIC16LC77-04/L — paket yang sama, pin-pada-pin kompatibel. Bagian paket yang berbeda memerlukan kerja ulang PCB diabaikan.
Variasi di dalam seri ini
Model-series yang sama yang kompatibel dengan penggantian PIC16LC77-04/L (sama faktor bentuk dan footprint) — berbeda di dalam Program Memory Size, Program Memory Type, Timers, Package, Core Architecture.
PIC16LC77-04I/L
✅ Drop-InKontak untuk harga
Lihat Datasheet →PIC16F877A-I/LG
✅ Drop-InKontak untuk harga
Lihat Datasheet →PIC16C77-04/PQ
✅ Drop-InKontak untuk harga
Lihat Datasheet →PIC16LC74A-04/PQ
✅ Drop-InKontak untuk harga
Lihat Datasheet →PIC16LC77-04/L Rating Maksimal & Karakteristik Listrik
| Core Architecture | PIC 8-bit Harvard RISC |
| Series | PIC16C |
| Program Memory Type | OTP (One-Time Programmable) |
| Program Memory Size | 14 KB (8K x 14 words) |
| RAM Size | 368 bytes |
| Frekuensi Bawah Maximum | 4 MHz |
| Instruction Throughput | 1 MIPS @ 4 MHz |
| Supply Voltage Range | 2.5 V to 6.0 V |
| I/O Pins | 33 |
| A/D Converter | 8 channels x 8-bit |
| Paket | 44-PLCC (J-Lead), 16.59 x 16.59 mm |
| Tipe Mounting | Surface Mount |
| Timers | Timer0, Timer1, Timer2 with PWM |
| Communication Interfaces | USART, SPI, I2C (SSP) |
| Watchdog Timer | Yes |
Konfigurasi Pin PIC16LC77-04/L
| Pin produk 1 | MCLR — Master Clear reset input (active low) |
| Pin produk 2 | OSC1 — Oscillator input / external clock input |
| Pin produk 3 | OSC2 — Oscillator output / clock out |
| Pin produk 4 | RA0/AN0 — PORTA bit 0 / Analog input 0 |
| Pin produk 5 | RA1/AN1 — PORTA bit 1 / Analog input 1 |
| Pin produk 6 | RA2/AN2 — PORTA bit 2 / Analog input 2 |
| Pin produk 7 | RA3/AN3/VREF — PORTA bit 3 / Analog input 3 / VREF+ |
| Pin produk 8 | RA4/T0CKI — PORTA bit 4 / Timer0 clock input |
| Pin produk 9 | RA5/AN4/SS — PORTA bit 5 / Analog input 4 / SPI Slave Select |
| Pin produk 10 | VSS — Ground |
| Pin produk 11 | VDD — Positive supply voltage |
| Pin produk 12 | RB0/INT — PORTB bit 0 / External interrupt |
| Pin produk 13 | RB1 — PORTB bit 1 |
| Pin produk 14 | RB2 — PORTB bit 2 |
| Pin produk 15 | RB3/PGM — PORTB bit 3 / Low-voltage programming |
| Pin produk 16 | RB4 — PORTB bit 4 |
| Pin produk 17 | RB5 — PORTB bit 5 |
| Pin produk 18 | RB6/PGC — PORTB bit 6 / ICSP clock |
| Pin produk 19 | RB7/PGD — PORTB bit 7 / ICSP data |
| Pin produk 20 | VSS — Ground |
| Pin produk 21 | VDD — Positive supply voltage |
| Pin produk 22 | RC0/T1OSO/T1CKI — PORTC bit 0 / Timer1 oscillator out / Timer1 clock |
| Pin produk 23 | RC1/T1OSI/CCP2 — PORTC bit 1 / Timer1 oscillator in / CCP2 |
| Pin produk 24 | RC2/CCP1 — PORTC bit 2 / CCP1 (PWM/Capture/Compare) |
| Pin produk 25 | RC3/SCK/SCL — PORTC bit 3 / SPI clock / I2C clock |
| Pin produk 26 | RC4/SDI/SDA — PORTC bit 4 / SPI data in / I2C data |
| Pin produk 27 | RC5/SDO — PORTC bit 5 / SPI data out |
| Pin produk 28 | RC6/TX/CK — PORTC bit 6 / USART transmit / clock |
| Pin produk 29 | RC7/RX/DT — PORTC bit 7 / USART receive / data |
| Pin produk 30 | VSS — Ground |
| Pin produk 31 | VDD — Positive supply voltage |
| Pin produk 32 | RD0/PSP0 — PORTD bit 0 / Parallel Slave Port bit 0 |
| Pin produk 33 | RD1/PSP1 — PORTD bit 1 / Parallel Slave Port bit 1 |
| Pin produk 34 | RD2/PSP2 — PORTD bit 2 / Parallel Slave Port bit 2 |
| Pin produk 35 | RD3/PSP3 — PORTD bit 3 / Parallel Slave Port bit 3 |
| Pin produk 36 | RD4/PSP4 — PORTD bit 4 / Parallel Slave Port bit 4 |
| Pin produk 37 | RD5/PSP5 — PORTD bit 5 / Parallel Slave Port bit 5 |
| Pin produk 38 | RD6/PSP6 — PORTD bit 6 / Parallel Slave Port bit 6 |
| Pin produk 39 | RD7/PSP7 — PORTD bit 7 / Parallel Slave Port bit 7 |
| Pin produk 40 | VSS — Ground |
| Pin produk 41 | VDD — Positive supply voltage |
| Pin produk 42 | RE0/RD/AN5 — PORTE bit 0 / Read control / Analog input 5 |
| Pin produk 43 | RE1/WR/AN6 — PORTE bit 1 / Write control / Analog input 6 |
| Pin produk 44 | RE2/CS/AN7 — PORTE bit 2 / Chip select / Analog input 7 |
Aplikasi Umum
PIC16LC77-04/L cocok untuk 6 aplikasis: Industrial Motor Control, Automotive Body Electronics, Home Appliance Control Boards, Battery-Powered Sensor Hubs, Legacy Equipment Retrofits, HVAC Control Systems.
Industrial Motor Control
The PIC16LC77-04/L fits industrial motor control boards because its 33 I/O pins and 8-channel 8-bit A/D converter provide ample PWM channels and current/voltage sensing inputs needed for BLDC and stepper control loops. The 4 MHz / 1 MIPS throughput delivers deterministic interrupt response for commutation timing, while the 2.5-6.0 V supply range accepts 24 V industrial rails after regulation. Place the 44-PLCC part on a socketed carrier for field service, and add 0.1 uF + bulk decoupling at each VDD pair per the Microchip datasheet typical application circuit.
Direkomendasikan
Automotive Body Electronics
In automotive body modules (window controllers, seat adjusters, mirror controls), the PIC16LC77-04/L provides the 33 I/O count needed for relay drivers and switch matrix scanning while running from a regulated 5 V supply tapped off the 12 V bus. The 8-bit A/D reads potentiometer positions for motor feedback, and the USART/SPI peripherals interface with body-control network ICs. Pair with the industrial-grade PIC16LC77-04I/L variant for under-hood temperature swings, and add TVS protection on inputs per automotive EMC best practices.
Direkomendasikan
Home Appliance Control Boards
Washing machines, dishwashers, and microwave ovens benefit from the PIC16LC77-04/L's 33 I/O pins for keypad scanning, seven-segment or LCD drive, sensor inputs, and triac-fired load control. The 14 KB OTP memory holds appliance state machines and timing routines, while the 8-channel A/D reads temperature, water level, and humidity sensors. The OTP memory suits high-volume consumer appliances where firmware lock prevents unauthorized modification, and the 44-PLCC package supports automated pick-and-place assembly on control boards.
Direkomendasikan
Battery-Powered Sensor Hubs
The PIC16LC77-04/L's low-voltage CMOS core supports operation down to 2.5 V, making it suitable for battery-powered sensor hubs that aggregate analog inputs and forward them via SPI to a radio module. Sleep current plus USART wakeup support multi-year battery life on 2xAA cells, while the 14 KB OTP memory holds sensor calibration tables and protocol stacks. Use the A/D converter's low-power modes between samples, and pair with a low-Iq LDO such as MCP1700 for sub-microamp quiescent operation during sleep.
Direkomendasikan
Legacy Equipment Retrofits
The PIC16LC77-04/L serves as a drop-in replacement for legacy PIC16C7X designs that need end-of-life refresh without PCB rework. Because the 44-PLCC pinout is shared across the PIC16C7X family, retrofitters can swap aging parts for new inventory while preserving firmware originally compiled for the same core. Industrial equipment with installed bases of PLCC sockets benefits from this longevity, and the OTP memory maintains bit-for-bit firmware compatibility with the original part.
Direkomendasikan
HVAC Control Systems
Heating, ventilation, and air-conditioning (HVAC) controllers use the PIC16LC77-04/L to drive triac outputs for fan speeds, read thermistor inputs through the 8-channel A/D, and communicate with indoor/outdoor unit networks via USART. The 33 I/O pins handle multiple relay banks and keypads, while the OTP memory stores zone calibration constants. Industrial temperature grade via the -04I/L variant supports unconditioned mechanical rooms, and the 2.5-6.0 V supply range accepts common 5 V and 3.3 V HVAC bus voltages.
Direkomendasikan
Ringkasan Produk Direkomendasikan
Data referensi engineering untuk PIC16LC77-04/L — pembandingan, panduan desain, dan informasi konformitas.
Panduan Pemilihan
Pembandingan dengan Alternatif
| Parameter Umum | Produk Ini | PIC16LC77-04I/L | PIC16F877A-I/L | PIC16C77-04/P | PIC16LC74A-04/PQ |
|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 44-PLCC (J-Lead) | 44-PLCC (J-Lead) - same | 44-PLCC (J-Lead) - same | 40-PDIP - different | 44-MQFP - different |
| Program Memory | 14 KB OTP | 14 KB OTP | 14 KB Flash | 14 KB OTP | 7 KB OTP |
| RAM Size | 368 bytes | 368 bytes | 368 bytes | 368 bytes | 192 bytes |
| Max Clock Frequency | 4 MHz | 4 MHz | 20 MHz | 4 MHz | 4 MHz |
| Supply Voltage Range | 2.5 V to 6.0 V | 2.5 V to 6.0 V | 2.0 V to 5.5 V | 2.5 V to 6.0 V | 2.5 V to 6.0 V |
| I/O Pins | 33 | 33 | 33 | 33 | 33 |
| A/D Converter | 8 ch x 8-bit | 8 ch x 8-bit | 8 ch x 10-bit | 8 ch x 8-bit | 8 ch x 8-bit |
| Memory Type | OTP | OTP | Flash | OTP | OTP |
| Temperature Grade | Standard | Industrial (-40C to +85C) | Industrial (-40C to +85C) | Standard | Standard |
Diferensiator Kunci
- Industry-standard PIC16C7X core with extensive Microchip toolchain support (vsPIC16F877A-I/L)
- Industrial temperature grade variant available in identical package (vsPIC16LC77-04I/L)
- 44-PLCC J-Lead package supports socketed field replacement (vsPIC16C77-04/P (40-PDIP))
Catatan Desain
Estimated: at VDD = 5 V and active-mode current of approximately 2 mA at 4 MHz, the PIC16LC77-04/L consumes roughly 10 mW. Add 0.1 uF ceramic decoupling close to each VDD pin pair (pins 11/21/31/41 share VDD; pins 10/20/30/40 share VSS) plus a single 10 uF bulk capacitor at the regulator output. Use a low-dropout regulator such as MCP1700 (250 mA, 1.6 uA quiescent) when operating from a 5 V or higher rail to keep sleep currents low for battery applications.
Because the program memory is OTP (one-time programmable), firmware bugs cannot be patched after programming - a misprogrammed part is scrap. Use the windowed UV-erasable CERDIP variant (PIC16C77-04/JW) or the flash-based PIC16F877A-I/L for development, then commit to OTP only after firmware is fully validated. Also note that the PIC16C77 has no on-chip debug; rely on MPLAB SIM and ICE hardware during firmware bring-up.
Place a 4.7 kohm pull-up on MCLR (pin 1) and configure the device for internal RC or external crystal oscillator mode per the datasheet. For 44-PLCC layout, use a PLCC socket (e.g., AMP 1-822516-1) to allow field replacement, and keep the oscillator traces short and guarded with a ground ring to reduce EMI susceptibility in industrial environments. Add a series 100 ohm resistor on MCLR if the device is exposed to ESD transients.
Informasi Konformitas
Compliance data not present in the verified web sources. Microchip Technology legacy PIC16C OTP parts were often available in both leaded and lead-free finishes; verify RoHS/lead-free status by lot with the distributor before procurement for RoHS-restricted markets.
