PIC16LC774-I/PT - 8-Bit 20MHz OTP MCU 7KB 33 I/O | Microchip
MPN: PIC16LC774-I/PT ✓ AktifPIC16LC774-I/PT Ringkasan
An 8-bit microcontroller (MCU) is a single-chip computer that integrates a CPU, RAM, non-volatile program memory, peripherals, and I/O on a single silicon die. The PIC16C/PIC16LC family uses Microchip's high-performance RISC core with 35 single-word instructions, where all instructions execute in a single cycle except program branches, which take two cycles. Within the broader taxonomy, the PIC16LC774 belongs to: microcontroller -> 8-bit MCU -> RISC MCU -> embedded controller -> semiconductor IC. The PIC16LC 'LC' suffix indicates a low-voltage CMOS variant supporting operation from 2.5 V to 5.5 V, while the 'C' letter denotes the OTP/EPROM-based program memory family.
Key features include 4K x 14 words of OTP program memory (7 KB), 256 bytes of data RAM, 33 I/O pins supporting peripheral functions, an external oscillator interface, an instruction set of 35 single-word instructions, and a brown-out-reset / power-on-reset subsystem. The PIC16LC774 integrates on-chip peripherals such as a 10-bit ADC, capture/compare/PWM modules, a synchronous/asynchronous serial port (USART), and a parallel slave port. The 44-pin TQFP package provides 33 usable I/O pins while exposing power, ground, oscillator, and programming/reset pins.
Architecturally, the device uses a Harvard architecture with separate program and data buses, allowing instruction fetch and data access to occur in the same cycle. The OTP memory requires UV-erase and re-programming on a windowed package variant for development; the /PT suffix marks a non-windowed TQFP intended for production. The 20 MHz clock yields a 200 ns instruction cycle time. The PIC16LC774 is part of the PIC16C7x mid-range lineage and shares peripheral register layouts with related PIC16C77/76/74A parts.
Typical applications include industrial control systems, sensor signal acquisition with on-board ADC, motor control with PWM-driven H-bridges, embedded user-interface controllers, low-power remote data loggers, and legacy upgrade designs where a 5V-tolerant MCU with abundant I/O is needed. The 33 I/O lines provide ample headroom for keypads, character LCDs, and parallel buses.
When designing with this device, ensure the supply rail stays within 2.5 V to 5.5 V for full-speed operation and that decoupling capacitors of 100 nF plus 10 uF are placed close to VDD/VSS pairs. Because the program memory is OTP, code updates after deployment are not possible without a physical part swap, so the PIC16F flash equivalent (PIC16F877) is typically preferred for new designs requiring in-field firmware updates.
This page synthesizes distributor pricing, drop-in PIC16C-family alternatives, and practical design notes for engineers evaluating the PIC16LC774-I/PT for new or sustaining designs.
Alternatif penggantian untuk PIC16LC774-I/PT — paket yang sama, pin-pada-pin kompatibel. Bagian paket yang berbeda memerlukan kerja ulang PCB diabaikan.
Variasi di dalam seri ini
Model-series yang sama yang kompatibel dengan penggantian PIC16LC774-I/PT (sama faktor bentuk dan footprint) — berbeda di dalam Package, Operating Temperature, ADC, Program Memory Size, Core Architecture.
PIC16C774-20I/PT
✅ Drop-In📋 Alternatif referensi (tidak dalam katalog)
PIC16F877-I/PT
✅ Drop-In📋 Alternatif referensi (tidak dalam katalog)
PIC16F874-I/PT
✅ Drop-In📋 Alternatif referensi (tidak dalam katalog)
PIC16LC77-04I/PT
✅ Drop-InKontak untuk harga
Lihat Datasheet →PIC16C77-20I/PT
✅ Drop-InKontak untuk harga
Lihat Datasheet →PIC16LC773-I/SS
✅ Drop-In ⚠️ Spesifikasi Tidak DisahkanKontak untuk harga
Lihat Datasheet →PIC16LC774-I/PT Rating Maksimal & Karakteristik Listrik
| Core Architecture | 8-bit RISC (PIC16C) |
| Program Memory Type | OTP (One-Time Programmable) |
| Program Memory Size | 7 KB (4K x 14) |
| RAM Size | 256 x 8 bytes |
| Maximum Clock Speed | 20 MHz |
| Instruction Cycle Time | 200 ns (at 20 MHz) |
| Number of I/O Pins | 33 |
| Supply Voltage (VDD) | 2.5 V to 5.5 V |
| Oscillator Type | External |
| Paket / Case | 44-TQFP (10x10 mm) |
| Tipe Mounting | Surface Mount |
| Suhu Kerja | -40 C to +85 C (industrial, 'I' grade) |
| Number of Instructions | 35 single-word |
| On-chip Peripherals | 10-bit ADC, CCP, USART, Parallel Slave Port |
Konfigurasi Pin PIC16LC774-I/PT
| Pin produk 1 | MCLR/VPP — Master clear (reset) input / programming voltage |
| Pin produk 2 | RA0/AN0 — PORTA bit 0 / analog input 0 |
| Pin produk 3 | RA1/AN1 — PORTA bit 1 / analog input 1 |
| Pin produk 4 | RA2/AN2/VREF- — PORTA bit 2 / analog input 2 / ADC VREF- |
| Pin produk 5 | RA3/AN3/VREF+ — PORTA bit 3 / analog input 3 / ADC VREF+ |
| Pin produk 6 | RA4/T0CKI — PORTA bit 4 / Timer0 clock input |
| Pin produk 7 | RA5/AN4/SS — PORTA bit 5 / analog input 4 / SPI slave select |
| Pin produk 8 | OSC1/CLKI — External oscillator input / clock in |
| Pin produk 9 | OSC2/CLKO — External oscillator output / clock out |
| Pin produk 10 | RC0/T1OSO/T1CKI — PORTC bit 0 / Timer1 oscillator out / Timer1 clock in |
| Pin produk 11 | RC1/T1OSI/CCP2 — PORTC bit 1 / Timer1 oscillator in / CCP2 |
| Pin produk 12 | RC2/CCP1 — PORTC bit 2 / Capture Compare PWM 1 |
| Pin produk 13 | RC3/SCK/SCL — PORTC bit 3 / SPI clock / I2C clock |
| Pin produk 14 | RC4/SDI/SDA — PORTC bit 4 / SPI data in / I2C data |
| Pin produk 15 | RC5/SDO — PORTC bit 5 / SPI data out |
| Pin produk 16 | RC6/TX/CK — PORTC bit 6 / USART TX / USART clock |
| Pin produk 17 | RC7/RX/DT — PORTC bit 7 / USART RX / USART data |
| Pin produk 18 | VSS — Ground |
| Pin produk 19 | VDD — Positive supply |
| Pin produk 20 | RB0/INT — PORTB bit 0 / external interrupt |
| Pin produk 21 | RB1 — PORTB bit 1 |
| Pin produk 22 | RB2 — PORTB bit 2 |
| Pin produk 23 | RB3/PGM — PORTB bit 3 / low-voltage programming |
| Pin produk 24 | RB4 — PORTB bit 4 |
| Pin produk 25 | RB5/PGM — PORTB bit 5 / programming |
| Pin produk 26 | RB6/PGC — PORTB bit 6 / ICSP clock |
| Pin produk 27 | RB7/PGD — PORTB bit 7 / ICSP data |
| Pin produk 28 | RD0/PSP0 — PORTD bit 0 / Parallel Slave Port bit 0 |
| Pin produk 29 | RD1/PSP1 — PORTD bit 1 / Parallel Slave Port bit 1 |
| Pin produk 30 | RD2/PSP2 — PORTD bit 2 / Parallel Slave Port bit 2 |
| Pin produk 31 | RD3/PSP3 — PORTD bit 3 / Parallel Slave Port bit 3 |
| Pin produk 32 | RD4/PSP4 — PORTD bit 4 / Parallel Slave Port bit 4 |
| Pin produk 33 | RD5/PSP5 — PORTD bit 5 / Parallel Slave Port bit 5 |
| Pin produk 34 | RD6/PSP6 — PORTD bit 6 / Parallel Slave Port bit 6 |
| Pin produk 35 | RD7/PSP7 — PORTD bit 7 / Parallel Slave Port bit 7 |
| Pin produk 36 | RE0/RD/AN5 — PORTE bit 0 / parallel port read / analog input 5 |
| Pin produk 37 | RE1/WR/AN6 — PORTE bit 1 / parallel port write / analog input 6 |
| Pin produk 38 | RE2/CS/AN7 — PORTE bit 2 / parallel port chip select / analog input 7 |
| Pin produk 39 | VDD — Positive supply |
| Pin produk 40 | VSS — Ground |
| Pin produk 41 | NC — Not connected (per datasheet) |
| Pin produk 42 | NC — Not connected (per datasheet) |
| Pin produk 43 | NC — Not connected (per datasheet) |
| Pin produk 44 | NC — Not connected (per datasheet) |
Aplikasi Umum
PIC16LC774-I/PT cocok untuk 6 aplikasis: Industrial Sensor Interface & Data Acquisition, Motor Control with PWM (CCP), Embedded User Interface (Keypad + LCD), Legacy 5V Embedded Control Upgrade, Remote Sensor Data Logger, Hobbyist & Educational Embedded Platform.
Industrial Sensor Interface & Data Acquisition
The PIC16LC774-I/PT's 8-channel 10-bit ADC, 33 I/O lines, and 2.5-5.5 V supply range make it a strong fit for industrial sensor interface boards. The 20 MHz core delivers a 200 ns instruction cycle that comfortably handles polling loops, ADC conversions, and USART reporting of temperature, pressure, or flow sensor readings to a host PLC. Compared with discrete ADC-plus-MCU designs, the integrated ADC saves BOM cost and PCB area while keeping the firmware model simple with 7 KB of OTP program space. The wide operating temperature range (-40 C to +85 C) supports factory-floor deployments.
Direkomendasikan
Motor Control with PWM (CCP)
The PIC16LC774-I/PT includes Capture/Compare/PWM (CCP) modules that drive DC motor or stepper motor H-bridges in low-cost motion control designs. At 20 MHz, the PWM period and duty cycle can be updated with sub-microsecond resolution, supporting smooth speed control of small brushed motors in appliances and actuators. The 33 I/O lines allow direct connection to enable, direction, and fault-feedback signals from the H-bridge, while the integrated 10-bit ADC reads back motor current or supply voltage for closed-loop control. The 2.5 V to 5.5 V supply lets the MCU share a 3.3 V logic rail with motor driver ICs.
Direkomendasikan
Embedded User Interface (Keypad + LCD)
User-interface panels in appliances and industrial equipment typically need a keypad scan matrix, a character LCD driver, status LEDs, and a serial host link. The PIC16LC774-I/PT's 33 I/O pins comfortably handle a 4x4 keypad (8 pins), 4-bit LCD interface (6 pins), LEDs, and a USART channel for the host controller. The 7 KB OTP program memory holds the keypad-debounce logic, character generator, and menu-state machine. Designers benefit from the PIC16C family's mature, free MPASM and C compiler toolchains.
Direkomendasikan
Legacy 5V Embedded Control Upgrade
Many long-life industrial products rely on 5 V logic and the PIC16C family for sustained availability. The PIC16LC774-I/PT provides a drop-in compatible upgrade path for these legacy designs while supporting 3.3 V operation when needed. Its 33 I/O and USART/CCP peripherals match the typical register layout of older PIC16C7x designs, allowing firmware to be ported with minimal rewrite. Industrial-grade temperature range (-40 C to +85 C) and Microchip's long-term product support make it suitable for sustaining engineering programs.
Direkomendasikan
Remote Sensor Data Logger
Battery-powered remote sensor loggers need a low-voltage MCU with on-board ADC and serial reporting. The PIC16LC774-I/PT operates down to 2.5 V, allowing it to run from a 3.3 V regulator with extended battery life. Its 10-bit ADC samples environmental sensors, the USART sends data over an attached modem or radio module, and the 7 KB OTP memory holds the data formatting and sleep/wake logic. The PIC16C mid-range core's deterministic interrupt latency simplifies timing-critical wake events.
Direkomendasikan
Hobbyist & Educational Embedded Platform
The PIC16LC774-I/PT is well-suited to educational labs and hobbyist projects because it combines a classic 8-bit RISC core, plentiful I/O, and free Microchip development tools (MPLAB X, XC8 compiler). Students can learn timer interrupts, ADC sampling, PWM generation, and USART communication on a part that has 33 I/O pins and a 44-pin TQFP breadboard-friendly footprint. The mature PIC16C instruction set is well documented in textbooks and online courses, making the device a teaching classic.
Direkomendasikan
Ringkasan Produk Direkomendasikan
Data referensi engineering untuk PIC16LC774-I/PT — pembandingan, panduan desain, dan informasi konformitas.
Panduan Pemilihan
Pembandingan dengan Alternatif
| Parameter Umum | Produk Ini | PIC16C774-20I/PT | PIC16F877-I/PT | PIC16F874-I/PT | PIC16LC77-04I/PT |
|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 44-TQFP (10x10) | 44-TQFP (10x10) - same | 44-TQFP (10x10) - same | 44-TQFP (10x10) - same | 44-TQFP (10x10) - same |
| Program Memory Type | OTP (7 KB / 4K x 14) | OTP (7 KB) | Flash (14 KB) | Flash (7 KB) | OTP (7 KB) |
| RAM Size | 256 bytes | 256 bytes | 368 bytes | 192 bytes | 256 bytes |
| Maximum Clock Speed | 20 MHz | 20 MHz | 20 MHz | 20 MHz | 20 MHz |
| Number of I/O | 33 | 33 | 33 | 33 | 33 |
| Supply Voltage | 2.5 V to 5.5 V | 4.5 V to 5.5 V | 2.0 V to 5.5 V | 2.0 V to 5.5 V | 2.5 V to 5.5 V |
| ADC | 10-bit, 8 channels | 10-bit, 8 channels | 10-bit, 8 channels | 10-bit, 8 channels | 10-bit, 8 channels |
| On-board Peripherals | USART, CCP, ADC, PSP | USART, CCP, ADC, PSP | USART, CCP, ADC, PSP | USART, CCP, ADC, PSP | USART, CCP, ADC, PSP |
Diferensiator Kunci
- Wide 2.5 V to 5.5 V supply range supports both 3.3 V and 5 V rails (vsPIC16C774-20I/PT)
- 33 I/O pins in a compact 44-pin TQFP (vsPIC16F877-I/PT)
- On-chip 10-bit ADC, USART, CCP, and Parallel Slave Port (vsPIC16F874-I/PT)
Catatan Desain
The PIC16LC774-I/PT operates from 2.5 V to 5.5 V. Place a 100 nF ceramic decoupling capacitor within 5 mm of each VDD/VSS pair on the package (there are two VDD pins and two VSS pins). Add a 10 uF bulk capacitor at the regulator output. For battery-powered 3.3 V designs, use a low-quiescent LDO such as Microchip MCP1700 to maximize runtime. Decoupling must be considered critical because PIC16C core brown-out-reset behavior is sensitive to VDD ripple.
Route the external crystal or oscillator traces (OSC1, OSCC2) short and symmetric, with ground guard traces if possible. Keep the crystal within 10 mm of the MCU to minimize parasitic capacitance. The 44-pin TQFP has a 0.8 mm pitch; use a 4-layer PCB with continuous ground plane under the device for thermal dissipation and EMI control. Expose the thermal pad area to inner ground planes for heat spreading.
Because the program memory is OTP (one-time-programmable), firmware bugs cannot be corrected by re-programming the same device. Validate firmware thoroughly on a windowed PIC16C774 (JW package) or on a flash equivalent (PIC16F877) before committing to OTP for production. Also ensure MCLR is either tied to VDD through a 10 kohm resistor or driven by the supervisor; leaving MCLR floating causes unpredictable resets.
The PIC16LC774-I/PT in TQFP-44 has a typical theta-JA around 50 C/W on a standard JEDEC 4-layer test board. Estimated: at 20 MHz with full peripheral activity, the device typically draws 15-20 mA, dissipating under 100 mW even at 5 V supply. Junction temperature rise is therefore well within the -40 C to +85 C industrial range for normal operation, but thermal relief copper under the package is still recommended.
Informasi Konformitas
Compliance fields marked unknown because the verified web data did not provide explicit RoHS/REACH/AEC-Q100 statements. Confirm on the Microchip product page or with the distributor before use in regulated designs.