PIC18F67J50T-I/PT - 8-Bit 48MHz USB MCU 128KB Flash TQFP-64
MPN: PIC18F67J50T-I/PT ✓ AktifPIC18F67J50T-I/PT Ringkasan
An 8-bit microcontroller (MCU) is a single-chip computer built around an 8-bit data path, optimized for deterministic real-time control, low power, and rich peripheral integration. Within the broader taxonomy, 8-bit MCUs sit below 16-bit and 32-bit MCUs in raw compute performance but above discrete logic in functional density. PIC18 devices extend Microchip's baseline PIC16 architecture with a 16-bit instruction word, linear data memory, and prioritized interrupts, making them suitable for USB-connected embedded designs that also need precision timing, ADC, and serial communication.
Key features include a built-in Full-Speed (12 Mbit/s) USB 2.0 device/host/OTG transceiver, four serial ports (USB, I2C, SPI up to 10 Mbit/s, and LIN-capable EUSART), a 10-bit ADC with up to 16 channels, five 16-bit timer/counters, and nanoWatt power management with multiple idle and sleep modes. The 64-pin TQFP exposes 49 digital I/O pins plus dedicated analog, oscillator, and programming/debug pins for ICSP.
Architecturally, the PIC18F67J50 uses a Harvard-style 16-bit instruction bus with an 8-bit data path, single-cycle ALU operations, and a hardware multiplier. Its 128KB flash is organized as 64K x 16 words, while the data EEPROM and SRAM sit on independent buses for deterministic interrupt latency. The integrated USB SIE eliminates the need for an external PHY, saving both board area and BOM cost.
Typical applications include USB-to-UART bridges, HID peripherals (keyboards, mice, game controllers), industrial sensor data loggers, low-power portable instrumentation, automotive body/comfort LIN nodes, and embedded web servers. The combination of USB connectivity and nanoWatt sleep modes makes the part particularly attractive for always-on USB devices that must draw negligible current when the host is suspended.
When designing with this MCU, allocate the analog Vcap pin to a low-ESR 4.7uF to 10uF decoupling capacitor and tie the ENVREG pin to VDD when the internal 2.5V regulator is used. For USB applications, ensure the D+/D- trace impedance is 90 ohm differential and that the Vbus sense pin is connected for proper attach detection.
This page consolidates distributor pricing, drop-in same-package alternatives, and application design guidance drawn from Microchip's PIC18F87J50 family datasheet, helping engineers select the right variant and avoid common integration pitfalls not covered in the standalone datasheet.
Alternatif penggantian untuk PIC18F67J50T-I/PT — paket yang sama, pin-pada-pin kompatibel. Bagian paket yang berbeda memerlukan kerja ulang PCB diabaikan.
Variasi di dalam seri ini
Model-series yang sama yang kompatibel dengan penggantian PIC18F67J50T-I/PT (sama faktor bentuk dan footprint) — berbeda di dalam ADC, Package, Operating Temperature, Timers, Program Memory (Flash).
PIC18F67J10T-I/PT
✅ Drop-In ⚠️ Spesifikasi Tidak DisahkanKontak untuk harga
Lihat Datasheet →PIC18F66J50T-I/PT
✅ Drop-InKontak untuk harga
Lihat Datasheet →PIC18F65J50T-I/PT
✅ Drop-In ⚠️ Spesifikasi Tidak DisahkanKontak untuk harga
Lihat Datasheet →PIC18F66J55-I/PT
✅ Drop-In ⚠️ Spesifikasi Tidak DisahkanKontak untuk harga
Lihat Datasheet →PIC18F65K80T-I/PT
✅ Drop-InKontak untuk harga
Lihat Datasheet →PIC18F67J50T-I/PT Rating Maksimal & Karakteristik Listrik
| Core | PIC18 8-bit RISC |
| Instruction Set | PIC18 (16-bit instruction word, 8-bit data path) |
| Program Memory (Flash) | 128 KB (64K x 16 words) |
| Data SRAM | 3,904 bytes |
| Maximum CPU Clock | 48 MHz |
| MIPS (Dhrystone) | 12 MIPS |
| Supply Voltage (VDD) | 2.0 V to 3.6 V |
| Suhu Kerja | -40 C to +85 C (Industrial) |
| USB Controller | USB 2.0 Full-Speed (12 Mbit/s), device/host/OTG SIE on-chip |
| Serial Interfaces | USB, I2C (MSSP), SPI (up to 10 Mbit/s), EUSART (LIN-capable) |
| ADC | 10-bit, up to 16 channels |
| Timers | 5 x 16-bit timer/counter |
| Digital I/O Pins | 49 |
| Paket | 64-pin TQFP (10x10 mm), pitch 0.5 mm |
| Tipe Mounting | Surface Mount |
| Level MSL | 3 (168 hours) |
| Status RoHS | Compliant |
| Programming/Debug | ICSP via PGC/PGD, supports MPLAB tools |
Konfigurasi Pin PIC18F67J50T-I/PT
| Pin produk 1 | RC0 — Digital I/O / analog input AN12 |
| Pin produk 2 | RC1 — Digital I/O / analog input AN13 / CCP2 |
| Pin produk 3 | RC2 — Digital I/O / analog input AN14 |
| Pin produk 4 | RC3 — Digital I/O / analog input AN15 / SCL |
| Pin produk 5 | RC4 — Digital I/O / SDA |
| Pin produk 6 | RC5 — Digital I/O / D- |
| Pin produk 7 | RC6 — Digital I/O / TX/CK |
| Pin produk 8 | RC7 — Digital I/O / RX/DT |
| Pin produk 9 | RD0 — Digital I/O |
| Pin produk 10 | RD1 — Digital I/O |
| Pin produk 11 | RD2 — Digital I/O |
| Pin produk 12 | RD3 — Digital I/O |
| Pin produk 13 | RD4 — Digital I/O |
| Pin produk 14 | RD5 — Digital I/O |
| Pin produk 15 | RD6 — Digital I/O |
| Pin produk 16 | RD7 — Digital I/O |
| Pin produk 17 | VSS — Ground reference |
| Pin produk 18 | VDD — Positive supply voltage (2.0V-3.6V) |
| Pin produk 19 | RE0 — Digital I/O / analog input AN5 |
| Pin produk 20 | RE1 — Digital I/O / analog input AN6 |
| Pin produk 21 | RE2 — Digital I/O / analog input AN7 |
| Pin produk 22 | RE3 — Digital I/O / analog input AN8 |
| Pin produk 23 | RE4 — Digital I/O / analog input AN9 |
| Pin produk 24 | RE5 — Digital I/O / analog input AN10 |
| Pin produk 25 | RE6 — Digital I/O / analog input AN11 |
| Pin produk 26 | RE7 — Digital I/O / CCP2 |
| Pin produk 27 | RA0 — Digital I/O / analog input AN0 |
| Pin produk 28 | RA1 — Digital I/O / analog input AN1 |
| Pin produk 29 | RA2 — Digital I/O / analog input AN2 |
| Pin produk 30 | RA3 — Digital I/O / analog input AN3 / Vref+ |
| Pin produk 31 | RA4 — Digital I/O / analog input AN4 |
| Pin produk 32 | RA5 — Digital I/O / analog input AN5 |
| Pin produk 33 | OSC1 — Crystal oscillator input / external clock |
| Pin produk 34 | OSC2 — Crystal oscillator output |
| Pin produk 35 | VSS — Ground reference |
| Pin produk 36 | VDD — Positive supply voltage (2.0V-3.6V) |
| Pin produk 37 | RB0 — Digital I/O / analog input AN12 |
| Pin produk 38 | RB1 — Digital I/O / analog input AN10 |
| Pin produk 39 | RB2 — Digital I/O / analog input AN8 |
| Pin produk 40 | RB3 — Digital I/O / analog input AN9 |
| Pin produk 41 | RB4 — Digital I/O / analog input AN11 |
| Pin produk 42 | RB5 — Digital I/O / analog input AN13 / CCP3 |
| Pin produk 43 | RB6 — Digital I/O / PGC (ICSP clock) |
| Pin produk 44 | RB7 — Digital I/O / PGD (ICSP data) |
| Pin produk 45 | VUSB — USB internal transceiver supply (3.3V regulated) |
| Pin produk 46 | VBUS — USB Vbus sense input (5V tolerant) |
| Pin produk 47 | D+ — USB D+ data line |
| Pin produk 48 | D- — USB D- data line |
| Pin produk 49 | RF0 — Digital I/O |
| Pin produk 50 | RF1 — Digital I/O |
| Pin produk 51 | RF2 — Digital I/O |
| Pin produk 52 | RF3 — Digital I/O |
| Pin produk 53 | RF4 — Digital I/O |
| Pin produk 54 | RF5 — Digital I/O |
| Pin produk 55 | RF6 — Digital I/O |
| Pin produk 56 | RF7 — Digital I/O |
| Pin produk 57 | RG0 — Digital I/O / CCP4 |
| Pin produk 58 | RG1 — Digital I/O / CCP5 |
| Pin produk 59 | RG2 — Digital I/O |
| Pin produk 60 | RG3 — Digital I/O |
| Pin produk 61 | RG4 — Digital I/O |
| Pin produk 62 | RG5 — Digital I/O |
| Pin produk 63 | VCAP — Internal 2.5V regulator decoupling (4.7uF-10uF low-ESR) |
| Pin produk 64 | ENVREG — Internal regulator enable (tie to VDD to enable) |
Aplikasi Umum
PIC18F67J50T-I/PT cocok untuk 6 aplikasis: USB-to-UART Bridge, USB HID Peripherals, Industrial Sensor Data Logger, Automotive LIN Comfort/Body Node, USB-Connected Portable Test Instrument, Embedded Web/IoT Edge Node.
USB-to-UART Bridge
The PIC18F67J50T-I/PT is a natural fit for USB-to-UART bridges because it integrates a Full-Speed USB 2.0 device SIE alongside a hardware LIN-capable EUSART. At 48 MHz the MCU delivers 12 MIPS, easily handling 921,600-baud UART streaming while leaving CPU headroom for buffer management. The 3,904-byte SRAM accommodates 64-byte USB endpoints plus ring buffers for simultaneous TX/RX. Designers wire D+/D- to the USB connector with 90 ohm differential impedance and use the Vbus sense pin for attach detection, eliminating an external transceiver and reducing BOM cost versus discrete USB-UART ICs such as FT232.
Direkomendasikan
USB HID Peripherals
For HID peripherals (keyboards, mice, gamepads, custom input devices), the PIC18F67J50T-I/PT's on-chip USB FS SIE and 49 digital I/O pins enable scan matrix reading, LED driving, and USB HID report generation without external logic. The 10-bit ADC supports analog joystick inputs alongside digital scan matrices, while the nanoWatt sleep modes let battery-powered mice meet USB suspend current (< 2.5 mA) requirements. The 128 KB flash holds full HID report descriptors and Bootloader/KB firmware with room for vendor-specific extensions, and the ICSP interface permits in-field firmware upgrades for product refreshes.
Direkomendasikan
Industrial Sensor Data Logger
Industrial sensor data loggers benefit from the PIC18F67J50T-I/PT's 10-bit ADC with up to 16 channels for thermocouple, RTD, 4-20 mA, and bridge sensor digitization, plus 3,904 bytes of SRAM for circular sample buffers. Industrial temperature operation (-40 C to +85 C) matches factory-floor requirements, and the 128 KB flash stores weeks of timestamped readings. The I2C/SPI/EUSART ports attach external FRAM or SD cards for long-term storage, while the USB port enables fast log offload. The nanoWatt idle modes drop supply current during sleep intervals between samples, extending battery life in remote installations.
Direkomendasikan
Automotive LIN Comfort/Body Node
Within an automotive LIN network, the PIC18F67J50T-I/PT (with extended qualification on related family parts) acts as a slave body/comfort node controlling window lifters, seat adjusters, mirror modules, or ambient lighting. The LIN-capable EUSART implements LIN 1.3/2.0/2.1 slave protocol in firmware without an external transceiver, and the 10-bit ADC reads mirror-position potentiometers and motor current sense. The 49 I/O pins drive multiple relays or H-bridge pre-drivers while the nanoWatt sleep modes meet automotive quiescent current targets. For AEC-Q100 qualified deployment, choose the PIC18F67J50 family automotive-grade variant.
Direkomendasikan
USB-Connected Portable Test Instrument
Portable USB-connected instruments (logic probe front-ends, simple protocol analyzers, low-cost oscilloscope digitizer boards) benefit from the PIC18F67J50T-I/PT's combined USB, ADC, and timing resources. At 48 MHz the MCU samples external analog front-ends up to the 10-bit ADC's ~500 ksps throughput while streaming digitized data over Full-Speed USB to a host PC for display. The 128 KB flash stores calibration tables and protocol decoders, while ICSP permits in-field firmware updates. Industrial temperature operation ensures stable readings in laboratory and field environments without thermal drift.
Direkomendasikan
Embedded Web/IoT Edge Node
For IoT edge nodes bridging sensors to USB-tethered hosts or to cloud gateways via USB-Ethernet dongles, the PIC18F67J50T-I/PT offers ample flash for MQTT-over-TCP stacks, JSON parsers, and TLS-lite security layers. The USB host capability allows direct attachment of USB-Ethernet or USB-Wi-Fi adapters, while the EUSART talks to Bluetooth or Sub-GHz modules for wireless backhaul. The 49 I/O pins drive sensor multiplexers, status LEDs, and user buttons, and nanoWatt sleep modes achieve single-digit mA standby currents suitable for solar/battery-powered edge installations.
Direkomendasikan
Ringkasan Produk Direkomendasikan
Data referensi engineering untuk PIC18F67J50T-I/PT — pembandingan, panduan desain, dan informasi konformitas.
Panduan Pemilihan
Pembandingan dengan Alternatif
| Parameter Umum | Produk Ini | PIC18F67J10T-I/PT | PIC18F66J50T-I/PT | PIC18F65J50T-I/PT | PIC18F66J55-I/PT | PIC18F65K80T-I/PT |
|---|---|---|---|---|---|---|
| Package | 64-pin TQFP (10x10 mm) | 64-pin TQFP (10x10 mm) - same | 64-pin TQFP (10x10 mm) - same | 64-pin TQFP (10x10 mm) - same | 64-pin TQFP (10x10 mm) - same | 64-pin TQFP (10x10 mm) - same |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Integrated USB SIE | USB 2.0 FS (12 Mbit/s) | USB 2.0 FS (12 Mbit/s) | USB 2.0 FS (12 Mbit/s) | USB 2.0 FS (12 Mbit/s) | USB 2.0 FS (12 Mbit/s) | No USB |
| Maximum Clock | 48 MHz | 48 MHz | 48 MHz | 48 MHz | 48 MHz | 64 MHz |
| Supply Voltage | 2.0 V - 3.6 V | 2.0 V - 3.6 V | 2.0 V - 3.6 V | 2.0 V - 3.6 V | 2.0 V - 3.6 V | 1.8 V - 5.5 V |
| Operating Temperature | -40 C to +85 C (Industrial) | -40 C to +85 C (Industrial) | -40 C to +85 C (Industrial) | -40 C to +85 C (Industrial) | -40 C to +85 C (Industrial) | -40 C to +85 C (Industrial) |
Diferensiator Kunci
- Integrated Full-Speed USB 2.0 SIE and transceiver (vsPIC18F65K80T-I/PT)
- Largest flash density in the 64-pin TQFP PIC18F87J50 family (vsPIC18F65J50T-I/PT)
- Industrial temperature range with extended peripherals (vsPIC18F67J10T-I/PT)
Catatan Desain
Estimated: At 48 MHz active and 3.3V VDD, the PIC18F67J50T-I/PT typically draws ~25 mA core current per Microchip datasheet typical characteristics. In USB suspend the part must drop below 2.5 mA system current to maintain USB compliance; switch to nanoWatt sleep and disable USB SIE clock to meet this. Decouple each VDD pin (18, 36) with 100 nF ceramic plus 4.7 uF bulk, and place the 4.7-10 uF Vcap capacitor within 5 mm of pin 63 with the lowest-ESR dielectric available (X5R/X7R).
Route the USB D+/D- pair as a 90 ohm differential with matched length (skew < 150 ps) and keep the pair over a continuous ground reference plane for the entire run. Place the Vcap capacitor on the same side as the IC with short traces to minimize core-ripple coupling into USB signaling. Per Microchip EMI/EMC design notes, place a ferrite bead or 10 ohm resistor in series with Vbus if the design must survive ESD strikes directly on the connector shield.
The internal 2.5V regulator (enabled by tying ENVREG=VDD) supplies the core and USB transceiver; insufficient Vcap decoupling produces core noise that can shift the USB eye diagram below USB 2.0 FS mask margins. Use a low-ESR 4.7 uF X5R/X7R 0603 (or larger) ceramic directly on pin 63 and verify the 3.3V rail is clean with an oscilloscope during USB enumeration. If the regulator is disabled (ENVREG tied to VSS), an external 2.5V supply must power the Vcap pin and meet the same ripple requirement.
Firmware developers frequently forget to disable unused peripherals' clocks via the appropriate PMD registers - leaving all peripherals enabled at 48 MHz can push active current to ~30 mA and break USB suspend budgets. Always invoke the recommended low-power initialization sequence from Microchip AN1095 (nanoWatt) before claiming low standby current. Likewise, do not configure RB6/RB7 as general I/O if ICSP in-field programming is required; doing so blocks subsequent firmware updates.
Informasi Konformitas
RoHS and lead-free compliant per Microchip product page; this -I/PT variant is not AEC-Q100 qualified - select the corresponding automotive-grade part for vehicle deployments. Halogen-free per Microchip material declaration.
