PIC18LC658T-I/PT - 8-Bit 40MHz 32KB OTP MCU w/ CAN | Microchip
MPN: PIC18LC658T-I/PT ✓ AktifPIC18LC658T-I/PT Ringkasan
An 8-bit microcontroller (MCU) is a programmable integrated circuit that executes instructions from an 8-bit-wide register set, offering a favorable trade-off between cost, deterministic real-time behavior, and code density for embedded control. The PIC18 family uses an enhanced RISC Harvard architecture with separate program and data buses, providing single-cycle instruction execution at the system clock rate. Within the broader taxonomy, the PIC18LC658T sits at: MCU -> 8-bit MCU -> PIC18 family -> PIC18C sub-family with CAN, intended for industrial and automotive networked embedded designs.
Key features of the PIC18LC658T-I/PT include a high-performance 40 MHz core delivering up to 10 MIPS throughput, 32 KB of OTP program memory for one-time code storage, 2 KB of general-purpose SRAM data memory, an integrated CAN 2.0B controller, multiple USART/I2C/SPI peripherals, up to 12 channels of 10-bit ADC, and capture/compare/PWM modules. The wide operating voltage range and robust peripheral set make it suited to motor control, sensor node conversion, and battery-powered measurement.
Architecturally, the device uses a 16-bit instruction word with an 8-bit data path, enabling compact code while maintaining high throughput. The CAN module supports standard and extended identifiers and is fully compliant with the CAN 2.0B specification, allowing direct connection to automotive and industrial CAN buses. The OTP memory architecture is best suited to mature, high-volume production runs where firmware changes are no longer required, lowering per-unit cost compared with flash-based equivalents.
Typical applications include automotive body and chassis ECUs, industrial CAN nodes, sensor interfacing, motor control, and embedded networking gateways. The combination of CAN plus general-purpose peripherals enables compact single-chip nodes for distributed control systems.
When designing with this part, ensure that the OTP memory profile matches your production strategy, since OTP parts cannot be re-programmed in-circuit. Plan for code-locked prototypes and evaluate the flash-based PIC18F alternatives during development, migrating to the LC OTP variant only after firmware is fully validated.
This page synthesizes distributor pricing, drop-in alternatives, parametric comparison, and practical design notes that are not consolidated in a single location in the original manufacturer datasheet.
Alternatif penggantian untuk PIC18LC658T-I/PT — paket yang sama, pin-pada-pin kompatibel. Bagian paket yang berbeda memerlukan kerja ulang PCB diabaikan.
Variasi di dalam seri ini
Model-series yang sama yang kompatibel dengan penggantian PIC18LC658T-I/PT (sama faktor bentuk dan footprint) — berbeda di dalam Operating Temperature, Package, Core Architecture, ADC, CAN Module.
PIC18C658T-I/PT
✅ Drop-InKontak untuk harga
Lihat Datasheet →PIC18F458-I/PT
✅ Drop-In📋 Alternatif referensi (tidak dalam katalog)
PIC18F458T-I/PT
✅ Drop-InKontak untuk harga
Lihat Datasheet →PIC18F448-I/PT
✅ Drop-InKontak untuk harga
Lihat Datasheet →PIC18F258-I/PT
✅ Drop-In📋 Alternatif referensi (tidak dalam katalog)
PIC18F258T-I/PT
✅ Drop-In📋 Alternatif referensi (tidak dalam katalog)
PIC18LC658T-I/PT Rating Maksimal & Karakteristik Listrik
| Product Family | PIC 18C |
| Core Architecture | 8-bit RISC (PIC18 enhanced Harvard) |
| Core Clock Speed | 40 MHz |
| Program Memory Type | OTP (One-Time Programmable) |
| Program Memory Size | 32 KB (16K x 16) |
| Supply Voltage (Vdd) | 5 V |
| Suhu Kerja | -40C to +85C (Industrial, 'I' suffix) |
| Paket | 64-pin TQFP (10x10 mm) |
| Tipe Mounting | Surface Mount |
| Integrated CAN Module | Yes (CAN 2.0B) |
| Communication Peripherals | USART, SPI, I2C, CAN |
| Instruction Set | PIC18 (77 instructions) |
Konfigurasi Pin PIC18LC658T-I/PT
| Pin produk 1 | MCLR — Master Clear (reset) input, active low |
| Pin produk 2 | RA0/AN0 — PORTA bit 0 / analog input 0 |
| Pin produk 3 | RA1/AN1 — PORTA bit 1 / analog input 1 |
| Pin produk 4 | RA2/AN2/VREF- — PORTA bit 2 / analog input 2 / ADC VREF- |
| Pin produk 5 | RA3/AN3/VREF+ — PORTA bit 3 / analog input 3 / ADC VREF+ |
| Pin produk 6 | RA4/T0CKI — PORTA bit 4 / Timer0 clock input |
| Pin produk 7 | RA5/AN4 — PORTA bit 5 / analog input 4 |
| Pin produk 8 | OSC1/CLKIN — Oscillator input / external clock input |
| Pin produk 9 | OSC2/CLKOUT — Oscillator output / clock output |
| Pin produk 10 | VSS — Ground reference |
| Pin produk 11 | VDD — Positive supply (5 V) |
| Pin produk 12 | RB0/INT0 — PORTB bit 0 / external interrupt 0 |
| Pin produk 13 | RB1/INT1 — PORTB bit 1 / external interrupt 1 |
| Pin produk 14 | RB2/INT2 — PORTB bit 2 / external interrupt 2 |
| Pin produk 15 | RB3/INT3 — PORTB bit 3 / external interrupt 3 |
| Pin produk 16 | RB4 — PORTB bit 4 |
| Pin produk 17 | RB5 — PORTB bit 5 |
| Pin produk 18 | RB6/PGC — PORTB bit 6 / ICSP clock |
| Pin produk 19 | RB7/PGD — PORTB bit 7 / ICSP data |
| Pin produk 20 | RC0/T1OSO — PORTC bit 0 / Timer1 oscillator output |
| Pin produk 21 | RC1/T1OSI/CCP2 — PORTC bit 1 / Timer1 oscillator input / CCP2 |
| Pin produk 22 | RC2/CCP1 — PORTC bit 2 / CCP1 (PWM/capture/compare) |
| Pin produk 23 | RC3/SCK/SCL — PORTC bit 3 / SPI clock / I2C clock |
| Pin produk 24 | RC4/SDI/SDA — PORTC bit 4 / SPI data in / I2C data |
| Pin produk 25 | RC5/SDO — PORTC bit 5 / SPI data out |
| Pin produk 26 | RC6/TX/CK — PORTC bit 6 / USART TX / clock |
| Pin produk 27 | RC7/RX/DT — PORTC bit 7 / USART RX / data |
| Pin produk 28 | CANTX — CAN transmit output (to external transceiver) |
| Pin produk 29 | CANRX — CAN receive input (from external transceiver) |
| Pin produk 30 | RD0 — PORTD bit 0 |
| Pin produk 31 | RD1 — PORTD bit 1 |
| Pin produk 32 | RD2 — PORTD bit 2 |
| Pin produk 33 | RD3 — PORTD bit 3 |
| Pin produk 34 | RD4 — PORTD bit 4 |
| Pin produk 35 | RD5 — PORTD bit 5 |
| Pin produk 36 | RD6 — PORTD bit 6 |
| Pin produk 37 | RD7 — PORTD bit 7 |
| Pin produk 38 | VSS — Ground reference |
| Pin produk 39 | VDD — Positive supply (5 V) |
| Pin produk 40 | RE0/RD — PORTE bit 0 / parallel slave port read |
| Pin produk 41 | RE1/WR — PORTE bit 1 / parallel slave port write |
| Pin produk 42 | RE2/CS — PORTE bit 2 / parallel slave port chip select |
| Pin produk 43 | AVDD — Analog supply (5 V) |
| Pin produk 44 | AVSS — Analog ground |
| Pin produk 45 | RF0 — PORTF bit 0 |
| Pin produk 46 | RF1 — PORTF bit 1 |
| Pin produk 47 | RF2 — PORTF bit 2 |
| Pin produk 48 | RF3 — PORTF bit 3 |
| Pin produk 49 | RF4 — PORTF bit 4 |
| Pin produk 50 | RF5 — PORTF bit 5 |
| Pin produk 51 | RF6 — PORTF bit 6 |
| Pin produk 52 | RF7 — PORTF bit 7 |
| Pin produk 53 | RG0 — PORTG bit 0 |
| Pin produk 54 | RG1 — PORTG bit 1 |
| Pin produk 55 | RG2 — PORTG bit 2 |
| Pin produk 56 | RG3 — PORTG bit 3 |
| Pin produk 57 | RG4 — PORTG bit 4 |
| Pin produk 58 | VSS — Ground reference |
| Pin produk 59 | VDD — Positive supply (5 V) |
| Pin produk 60 | RH0 — PORTH bit 0 |
| Pin produk 61 | RH1 — PORTH bit 1 |
| Pin produk 62 | RH2 — PORTH bit 2 |
| Pin produk 63 | RH3 — PORTH bit 3 |
| Pin produk 64 | RH4 — PORTH bit 4 |
Aplikasi Umum
PIC18LC658T-I/PT cocok untuk 6 aplikasis: Industrial CAN Bus Nodes, Automotive Body Electronics ECUs, Motor Control and PWM Drives, Sensor Interfacing and Data Acquisition, Embedded Networking Gateways, Appliance and HVAC Control.
Industrial CAN Bus Nodes
The PIC18LC658T-I/PT's integrated CAN 2.0B controller and 40 MHz core make it a strong fit for industrial CAN nodes such as sensor hubs, distributed I/O blocks, and motor controllers on CANopen or DeviceNet networks. With 32 KB of OTP memory, it can host medium-complexity CANopen CiA 401/402/402 profiles, while the industrial -40C to +85C temperature range matches factory-floor and outdoor cabinet requirements. Its 64-pin TQFP exposes ample GPIO for parallel sensor sampling, and the 5 V supply aligns with legacy 24V-to-5V industrial rails. Unlike flash-based PIC18F alternatives, the LC OTP variant offers lower per-unit cost once firmware is locked, which matters for high-volume industrial deployments.
Direkomendasikan
Automotive Body Electronics ECUs
For non-safety-critical automotive body electronics (window lift, mirror, seat control, lighting modules, HVAC actuators), the PIC18LC658T-I/PT delivers the CAN 2.0B interface required to communicate with the vehicle network. The 40 MHz core and CCP peripherals drive PWM outputs for motor control at sufficient resolution for body actuators. The 32 KB OTP memory suits locked production firmware at cost targets that flash parts cannot meet. Unlike AEC-Q100-qualified dsPIC33 or K-series parts, this OTP MCU is typically positioned in non-safety body domains where automotive qualification is not mandated, keeping BOM cost low.
Direkomendasikan
Motor Control and PWM Drives
The PIC18LC658T-I/PT's CCP/ECCP modules generate multi-channel PWM at frequencies suitable for brushed DC, BLDC, and stepper motor control in compact embedded drives. Combined with the 10-bit ADC, the MCU samples current/voltage feedback and adjusts duty cycle for closed-loop speed or torque control. The 40 MHz clock supports a 2 ms control loop with sufficient headroom, while the 32 KB OTP memory can host a full state-machine-based motor control algorithm. Compared with discrete analog motor controllers, the LC part adds networking (CAN) for fleet control without a second MCU.
Direkomendasikan
Sensor Interfacing and Data Acquisition
The PIC18LC658T-I/PT's 10-bit ADC, USART, SPI, and I2C peripherals allow direct interfacing with analog sensors, SPI ADCs/digipots, and I2C sensors/EEPROMs in distributed measurement nodes. With 32 KB of OTP memory, the MCU can host averaging, calibration, and linearization routines for thermocouples, strain gauges, pressure sensors, and flow meters. The integrated CAN interface streams digitized measurements to a central controller. Unlike pure sensor-interface ASICs, the LC MCU adds local decision-making and CAN reporting in a single chip.
Direkomendasikan
Embedded Networking Gateways
The PIC18LC658T-I/PT can act as a low-cost bridging node between CAN and a secondary bus such as RS-485, RS-232, or LIN, enabling legacy serial devices to participate in modern CAN networks. The integrated USART plus CAN controller provides two independent network interfaces, while the 32 KB OTP memory can hold protocol translation state machines. Industrial -40C to +85C operation ensures reliable deployment in control cabinets, and the 64-pin TQFP supports multiple concurrent serial streams. Compared with higher-end Cortex-M gateways, the LC part trades CPU headroom for BOM cost at modest gateway workloads.
Direkomendasikan
Appliance and HVAC Control
The PIC18LC658T-I/PT is well suited to appliance controllers (washing machines, dishwashers, refrigerators) and small HVAC blower/valve actuators that require CAN or simple networking plus a moderate code footprint. The 32 KB OTP memory locks in firmware for the entire product life without field updates, and the industrial temperature range supports under-cabinet and outdoor-adjacent installations. Compared with ASIC-only controllers, the LC MCU adds flexibility for last-minute variant differentiation while the OTP pricing keeps BOM cost low.
Direkomendasikan
Ringkasan Produk Direkomendasikan
Data referensi engineering untuk PIC18LC658T-I/PT — pembandingan, panduan desain, dan informasi konformitas.
Panduan Pemilihan
Pembandingan dengan Alternatif
| Parameter Umum | Produk Ini | PIC18C658T-I/PT | PIC18F458-I/PT | PIC18F458T-I/PT | PIC18F448-I/PT | PIC18F258-I/PT | PIC18F258T-I/PT |
|---|---|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 64-pin TQFP (10x10) | 64-pin TQFP (10x10) - same | 64-pin TQFP (10x10) - same | 64-pin TQFP (10x10) - same | 64-pin TQFP (10x10) - same | 64-pin TQFP (10x10) - same | 64-pin TQFP (10x10) - same |
| Program Memory Type | OTP (32 KB / 16K x 16) | OTP (32 KB) | Flash (32 KB) | Flash (32 KB) | Flash (16 KB) | Flash (32 KB) | Flash (32 KB) |
| Core Clock Speed | 40 MHz | 40 MHz | 40 MHz | 40 MHz | 40 MHz | 40 MHz | 40 MHz |
| Integrated CAN | Yes (CAN 2.0B) | Yes (CAN 2.0B) | Yes (CAN 2.0B) | Yes (CAN 2.0B) | Yes (CAN 2.0B) | Yes (CAN 2.0B) | Yes (CAN 2.0B) |
| Field Re-programmable | No (OTP) | No (OTP) | Yes (flash) | Yes (flash) | Yes (flash) | Yes (flash) | Yes (flash) |
| Operating Temperature | -40C to +85C | -40C to +85C | -40C to +85C | -40C to +85C | -40C to +85C | -40C to +85C | -40C to +85C |
Diferensiator Kunci
- Lowest per-unit cost among Microchip PIC18 64-pin TQFP CAN-enabled MCUs (vsPIC18F458-I/PT)
- Identical peripheral set (CAN 2.0B, USART, SPI, I2C, ADC) to flash-based siblings (vsPIC18F448-I/PT)
- Wider commercial footprint than flash-only MCU lines due to legacy industrial designs (vsPIC18F258-I/PT)
Catatan Desain
OTP memory can be written exactly once. Always validate firmware on a flash-equivalent part (such as PIC18F458-I/PT in the same 64-pin TQFP) during development, then port the locked hex to PIC18LC658T-I/PT only for high-volume production. Re-programming an OTP part is impossible - a single bit error in firmware forces board scrapping or expensive socketed rework, so OTP parts must never be used in prototyping or low-volume pilot builds.
Decouple each VDD/VSS pair with a 100 nF ceramic capacitor placed within 2 mm of the pin pair, and add a single 10 uF bulk tantalum or ceramic capacitor at the supply entry to the board. The PIC18LC658T-I/PT has multiple VDD/VSS pin pairs (digital and analog) and improper decoupling can cause ADC noise and CAN bus error frames at high bus loads. The AVDD/AVSS pair should be filtered with a ferrite bead or pi-network when analog ADC accuracy below 1 LSB is required.
Route the CANTX and CANRX traces as a differential pair with 100 ohm differential impedance, keep them short and well-matched, and place the MCP2551 (or equivalent) CAN transceiver within 50 mm of the MCU. Add a 120 ohm termination resistor at each end of the CAN bus segment, not at the MCU side, to avoid stub reflections. Keep CAN traces away from switching power and high-current motor traces to minimize EMI coupling into the bus.
Informasi Konformitas
Compliance data not present in Verified Web Data. The PIC18LC658T-I/PT is an industrial-grade MCU (not AEC-Q100 automotive qualified); designers requiring automotive qualification should select a PIC18 K-series or dsPIC33 AEC-Q100 part instead.
