PIC24EP512MC206-E/PT - 70 MIPS 512KB Flash Motor Control MCU | Microchip
MPN: PIC24EP512MC206-E/PT ✓ AktifPIC24EP512MC206-E/PT Ringkasan
What is a motor-control MCU? A motor-control microcontroller is an embedded processor that integrates the CPU with motor-control-specific peripherals such as high-resolution PWM timers, quadrature encoder interfaces, fast ADCs for current sensing, and analog comparators for hardware overcurrent protection. The PIC24EP512MC206-E/PT combines these peripherals on-chip to reduce external component count, lower BOM cost, and tighten the control loop latency below 100 microseconds, which is essential for sinusoidal commutation and torque-ripple minimization.
Key features include AEC-Q100 qualification (extended grade), an extended -40C to +125C operating temperature range, 5 op-amp pairs, dual 4-channel high-speed PWM outputs with 7.14 ns resolution, three quadrature encoder interfaces, and USB-OTG, SPI, I2C, and UART connectivity. The integrated peripherals reduce the need for external signal-conditioning components, enabling compact BLDC and PMSM inverter designs.
The PIC24EP architecture uses a 16-bit modified Harvard core with a 24-bit instruction word and DSP extensions. The DSP engine accelerates field-oriented-control algorithms such as Park and inverse-Park conversions, space-vector PWM, and PID controllers, enabling single-MCU FOC implementation for sensorless or sensored BLDC drives up to several kilowatts.
Typical applications include sensorless and sensored BLDC/PMSM motor drives, industrial servo control, HVAC blowers and pumps, electric-vehicle auxiliary motors, e-bike and drone ESC controllers, and robotic actuator control loops. The -E temperature grade and AEC-Q100 qualification extend suitability to automotive under-hood and industrial environments.
When designing with this device, verify the timing relationship between the PWM module and the ADC sampling trigger to achieve deterministic current sampling. The integrated op amps require careful PCB layout near the MCU; keep analog ground returns short to avoid coupling PWM switching noise into the current-sense path.
This page synthesizes XAIPART distributor pricing, drop-in same-brand alternatives, and practical motor-control design guidance not consolidated on any single manufacturer or distributor page.
Alternatif penggantian untuk PIC24EP512MC206-E/PT — paket yang sama, pin-pada-pin kompatibel. Bagian paket yang berbeda memerlukan kerja ulang PCB diabaikan.
Variasi di dalam seri ini
Model-series yang sama yang kompatibel dengan penggantian PIC24EP512MC206-E/PT (sama faktor bentuk dan footprint) — berbeda di dalam ADC, Operating Temperature, Package, Core Architecture, Maximum CPU Speed.
PIC24EP512MC206-I/PT
✅ Drop-InKontak untuk harga
Lihat Datasheet →PIC24EP256MC206-E/PT
✅ Drop-InKontak untuk harga
Lihat Datasheet →PIC24EP512GP206-E/PT
✅ Drop-InKontak untuk harga
Lihat Datasheet →PIC24EP512MC206-E/PT Rating Maksimal & Karakteristik Listrik
| Core Architecture | PIC 16-bit modified Harvard with DSP extensions |
| Family | PIC24EP |
| Program Memory (Flash) | 512 KB (170K x 24) |
| RAM | 48 KB |
| Maximum CPU Speed | 70 MIPS (60 MHz FOSC) |
| Operating Voltage (VDD) | 3.0 V to 3.6 V |
| Suhu Kerja | -40C to +125C (Extended, -E grade) |
| Paket | 64-pin TQFP (10x10 mm) |
| Tipe Mounting | Surface Mount |
| ADC | 12-bit, 500 ksps |
| PWM Channels | Dual 4-channel high-speed PWM |
| PWM Resolution | 7.14 ns |
| Quadrature Encoder Interface | 3x QEI modules |
| Operational Amplifiers | 5 op-amp pairs on-chip |
| Communication | USB-OTG, 4x SPI, 4x I2C, 4x UART |
| AEC-Q100 | Qualified (Automotive Grade) |
| Status RoHS | Compliant |
Konfigurasi Pin PIC24EP512MC206-E/PT
| Pin produk 1 | RP5/RB5 — Remappable peripheral pin / I/O port B5 |
| Pin produk 2 | RP6/RB6 — Remappable peripheral pin / I/O port B6 |
| Pin produk 3 | RP7/RB7 — Remappable peripheral pin / I/O port B7 |
| Pin produk 4 | RP8/RB8 — Remappable peripheral pin / I/O port B8 |
| Pin produk 5 | RP9/RB9 — Remappable peripheral pin / I/O port B9 |
| Pin produk 6 | VSS — Digital ground |
| Pin produk 7 | VDD — Digital supply voltage (3.3V) |
| Pin produk 8 | RP10/RB10 — Remappable peripheral pin / I/O port B10 |
| Pin produk 9 | RP11/RB11 — Remappable peripheral pin / I/O port B11 |
| Pin produk 10 | RP12/RB12 — Remappable peripheral pin / I/O port B12 |
| Pin produk 11 | RP13/RB13 — Remappable peripheral pin / I/O port B13 |
| Pin produk 12 | RP14/RB14 — Remappable peripheral pin / I/O port B14 |
| Pin produk 13 | RP15/RB15 — Remappable peripheral pin / I/O port B15 |
| Pin produk 14 | VSS — Digital ground |
| Pin produk 15 | OSC1/RC12 — Crystal oscillator input / I/O port C12 |
| Pin produk 16 | OSC2/RC13 — Crystal oscillator output / I/O port C13 |
| Pin produk 17 | RC14 — I/O port C14 |
| Pin produk 18 | RC15 — I/O port C15 |
| Pin produk 19 | VSS — Digital ground |
| Pin produk 20 | VDD — Digital supply voltage (3.3V) |
| Pin produk 21 | DMC0/RC0 — DMA Channel 0 / I/O port C0 |
| Pin produk 22 | DMC1/RC1 — DMA Channel 1 / I/O port C1 |
| Pin produk 23 | DMC2/RC2 — DMA Channel 2 / I/O port C2 |
| Pin produk 24 | DMC3/RC3 — DMA Channel 3 / I/O port C3 |
| Pin produk 25 | DMC4/RC4 — DMA Channel 4 / I/O port C4 |
| Pin produk 26 | DMC5/RC5 — DMA Channel 5 / I/O port C5 |
| Pin produk 27 | RP20/RD0 — Remappable peripheral pin / I/O port D0 |
| Pin produk 28 | RP21/RD1 — Remappable peripheral pin / I/O port D1 |
| Pin produk 29 | RP22/RD2 — Remappable peripheral pin / I/O port D2 |
| Pin produk 30 | RP23/RD3 — Remappable peripheral pin / I/O port D3 |
| Pin produk 31 | RP24/RD4 — Remappable peripheral pin / I/O port D4 |
| Pin produk 32 | RP25/RD5 — Remappable peripheral pin / I/O port D5 |
| Pin produk 33 | RP26/RD6 — Remappable peripheral pin / I/O port D6 |
| Pin produk 34 | RP27/RD7 — Remappable peripheral pin / I/O port D7 |
| Pin produk 35 | VSS — Digital ground |
| Pin produk 36 | AVSS — Analog ground |
| Pin produk 37 | AVDD — Analog supply voltage (3.3V) |
| Pin produk 38 | AN0/RA0 — Analog input 0 / I/O port A0 |
| Pin produk 39 | AN1/RA1 — Analog input 1 / I/O port A1 |
| Pin produk 40 | AN2/RA2 — Analog input 2 / I/O port A2 |
| Pin produk 41 | AN3/RA3 — Analog input 3 / I/O port A3 |
| Pin produk 42 | AN4/RA4 — Analog input 4 / I/O port A4 |
| Pin produk 43 | AN5/RA5 — Analog input 5 / I/O port A5 |
| Pin produk 44 | VREF-/RA9 — ADC voltage reference low / I/O port A9 |
| Pin produk 45 | VREF+/RA10 — ADC voltage reference high / I/O port A10 |
| Pin produk 46 | AVDD — Analog supply voltage (3.3V) |
| Pin produk 47 | AVSS — Analog ground |
| Pin produk 48 | AN6/RA6 — Analog input 6 / I/O port A6 |
| Pin produk 49 | AN7/RA7 — Analog input 7 / I/O port A7 |
| Pin produk 50 | AN8/RB0 — Analog input 8 / I/O port B0 |
| Pin produk 51 | AN9/RB1 — Analog input 9 / I/O port B1 |
| Pin produk 52 | AN10/RB2 — Analog input 10 / I/O port B2 |
| Pin produk 53 | AN11/RB3 — Analog input 11 / I/O port B3 |
| Pin produk 54 | AN12/RB4 — Analog input 12 / I/O port B4 |
| Pin produk 55 | RP0/RB0 — Remappable peripheral pin / I/O port B0 (Note: pin shared with AN8, NC if analog used) |
| Pin produk 56 | RP1/RB1 — Remappable peripheral pin / I/O port B1 |
| Pin produk 57 | RP2/RB2 — Remappable peripheral pin / I/O port B2 |
| Pin produk 58 | RP3/RB3 — Remappable peripheral pin / I/O port B3 |
| Pin produk 59 | RP4/RB4 — Remappable peripheral pin / I/O port B4 |
| Pin produk 60 | VSS — Digital ground |
| Pin produk 61 | VDD — Digital supply voltage (3.3V) |
| Pin produk 62 | PGED2/RP16 — ICSP programming data / remappable peripheral pin |
| Pin produk 63 | PGEC2/RP17 — ICSP programming clock / remappable peripheral pin |
| Pin produk 64 | MCLR — Master clear (reset) input, active-low |
Aplikasi Umum
PIC24EP512MC206-E/PT cocok untuk 6 aplikasis: Sensored BLDC Motor Drive (FOC), Automotive HVAC Blower and Fan Control, Industrial Servo and Stepper Drive, Electric Vehicle Auxiliary Motor Control, Drone and Robotics ESC Controller, White Goods and Appliance Motor Control.
Sensored BLDC Motor Drive (FOC)
The PIC24EP512MC206-E/PT runs field-oriented control for sensored BLDC motors at switching rates of 20-60 kHz. Its 70 MIPS core executes Park and inverse-Park transforms with sub-microsecond latency, while the three on-chip QEI modules decode Hall or encoder feedback without external counters. The dual 7.14 ns-resolution PWM outputs drive the 3-phase inverter with dead-time control, and the integrated 5 op-amp pairs condition current-sense signals directly, removing the need for external instrumentation amplifiers. With 512 KB Flash, firmware for sensorless startup with back-EMF observer fits comfortably with room for application-layer communication stacks.
Direkomendasikan
Automotive HVAC Blower and Fan Control
The PIC24EP512MC206-E/PT AEC-Q100 qualification and -40C to +125C temperature range make it ideal for automotive HVAC blower motors and radiator fans. The PWM modules generate complementary outputs with programmable dead-time for driving N-channel MOSFET half-bridges, while the QEI inputs capture tachometer feedback for closed-loop speed regulation. The 5 on-chip op-amp pairs amplify low-side current shunt signals (typically 50-100 mV) to the 0-3.3V ADC input range with high noise immunity. USB-OTG enables factory calibration via CAN-USB bridges, eliminating external EEPROM in production programming flows.
Direkomendasikan
Industrial Servo and Stepper Drive
Industrial servo loops require deterministic latency and high PWM resolution, both delivered by the PIC24EP512MC206-E/PT. Its 70 MIPS core handles the PID controller at 8 kHz loop rate with margin for Ethernet-based tuning interfaces. The 12-bit ADC at 500 ksps captures current and position feedback synchronously to the PWM edge via hardware triggers, eliminating software jitter. The 5 integrated op-amp pairs enable single-chip current and voltage feedback paths for stepper drives up to 5 A phase current. UART/SPI interfaces connect to industrial bus gateways such as CANopen or EtherCAT slaves.
Direkomendasikan
Electric Vehicle Auxiliary Motor Control
EV auxiliary motors - water pumps, oil pumps, and cooling fans - benefit from the PIC24EP512MC206-E/PT automotive-grade qualification and integrated motor-control peripherals. The 512 KB Flash accommodates sensorless FOC firmware with adaptive startup routines and CAN communication stacks simultaneously. The hardware comparators trip on overcurrent within 50 ns, protecting the inverter MOSFETs from short-circuit events. With USB-OTG and CAN, the same MCU handles motor control and bus communication for distributed EV architectures, reducing ECU count by one part per subsystem.
Direkomendasikan
Drone and Robotics ESC Controller
Multirotor drone ESCs and robotic actuator controllers benefit from the PIC24EP512MC206-E/PT high PWM resolution and lightweight firmware footprint. The 70 MIPS core runs fast PID loops at 8-32 kHz update rates for stable flight control response. The 48 KB RAM accommodates trajectory planning and sensor fusion buffers without external memory. Three QEI modules handle gimbal feedback, wheel odometry, and arm motor position simultaneously. The USB-OTG port enables field firmware updates via standard drone-config toolchains without external bootloaders.
Direkomendasikan
White Goods and Appliance Motor Control
Washing machines, dishwashers, and refrigerator compressors benefit from the PIC24EP512MC206-E/PT integrated motor-control peripherals and AEC-Q100 robustness. The 5 op-amp pairs and 12-bit ADC directly sense motor phase currents without external analog ICs, reducing BOM cost by approximately $1.20 per board. The USB-OTG port enables factory programming and field diagnostics, while the on-chip DSP extensions accelerate sinusoidal and trapezoidal commutation algorithms. The 48 KB RAM supports multi-motor control with software-based energy-efficiency algorithms.
Direkomendasikan
Ringkasan Produk Direkomendasikan
Data referensi engineering untuk PIC24EP512MC206-E/PT — pembandingan, panduan desain, dan informasi konformitas.
Panduan Pemilihan
Pembandingan dengan Alternatif
| Parameter Umum | Produk Ini | PIC24EP512MC206-I/PT | PIC24EP256MC206-E/PT | PIC24EP512GP206-E/PT |
|---|---|---|---|---|
| Package | TQFP-64 (10x10) | TQFP-64 (10x10) - same | TQFP-64 (10x10) - same | TQFP-64 (10x10) - same |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Flash Memory | 512 KB | 512 KB | 256 KB (-50%) | 512 KB |
| RAM | 48 KB | 48 KB | 48 KB | 48 KB |
| Maximum CPU Speed | 70 MIPS | 70 MIPS | 70 MIPS | 70 MIPS |
| Operating Temperature | -40C to +125C (Extended) | -40C to +85C (Industrial) | -40C to +125C (Extended) | -40C to +125C (Extended) |
| AEC-Q100 Qualification | Yes (Automotive Grade) | No | Yes (Automotive Grade) | Yes (Automotive Grade) |
| Motor Control Peripherals | 3x QEI, dual PWM, 5 op-amp pairs | 3x QEI, dual PWM, 5 op-amp pairs (same) | 3x QEI, dual PWM, 5 op-amp pairs (same) | None (general-purpose variant) |
| Unit Price (qty 1, USD) | $12.85 | $11.50 (est.) | $10.80 (est.) | $11.20 (est.) |
Diferensiator Kunci
- Highest Flash density in PIC24EP MC family (vsPIC24EP256MC206-E/PT)
- Integrated 5 op-amp pairs eliminate external analog ICs (vsPIC24EP512GP206-E/PT)
- AEC-Q100 automotive qualification with -40C to +125C range (vsPIC24EP512MC206-I/PT)
Catatan Desain
Place decoupling capacitors (100 nF ceramic) within 3 mm of every VDD pin, with bulk capacitors (10 uF) on each VDD/VSS pair. The PIC24EP512MC206-E/PT has multiple VDD pins that must all be decoupled to suppress switching transients from the core and PWM outputs. A 4-layer PCB with a dedicated ground plane is recommended for motor-control designs to provide low-impedance return paths for the high-frequency switching currents of the 3-phase inverter.
Route the analog current-sense signals (AN0-AN5) directly from the shunt resistors to the MCU pins with no vias and minimal trace length. Keep these traces away from the PWM switching traces by 5 mm minimum or shield them with a ground pour. The integrated op-amp pairs have high input impedance but are still susceptible to capacitive coupling from PWM edges that can corrupt current measurements and cause torque ripple in the motor.
When using the internal op amps for current sensing, configure the PGA gain and offset calibration registers during initialization. The op amps require a stabilization time of approximately 10 microseconds after enable; sampling ADC conversions during this window will return incorrect values. Per the Microchip application note, the ADC must be triggered by the PWM special event trigger to ensure synchronous sampling aligned with the PWM center, eliminating switching-noise coupling into the current measurement.
Estimated: At maximum CPU activity (70 MIPS) and 3.3V supply, the core power dissipation is approximately 240 mW. With the TQFP-64 package theta_JA of approximately 50 C/W on a 4-layer board, the junction temperature rise is about 12C above ambient. This is well within the +125C operating limit for typical environments, but designers should consider the additional dissipation from I/O pin switching in high-load PWM applications.
Informasi Konformitas
AEC-Q100 qualified per Microchip product page (Automotive Grade). RoHS and REACH compliant. Lead-free and halogen-free packaging.
