PIC24F16KL402-I/SS - 16-bit XLP MCU, 32MHz, 16KB Flash | Microchip
MPN: PIC24F16KL402-I/SS ✓ AktifPIC24F16KL402-I/SS Ringkasan
A microcontroller (MCU) is a single-chip computer containing a CPU core, program and data memory, peripherals, and I/O. The 16-bit PIC24F family sits between 8-bit PIC18 devices and 32-bit PIC32 parts in Microchip's portfolio, offering a balance of low cost, low power, and higher code density for C-based firmware. The 'KL' sub-series is the low-pin-count, low-power branch aimed at consumer, medical, and portable safety/security products.
Key features include a 10-bit, up to 12-channel A/D converter with 500 ksps conversion rate and Sleep/Idle-mode sampling, dual rail-to-rail analog comparators with programmable I/O, an on-chip voltage reference, three 16-bit timers, a 16-bit Capture/Compare/PWM (ECCP) module, an MSSP peripheral supporting both I2C and SPI, and up to 25 general-purpose I/O pins. The nanoWatt XLP technology enables currents below 1.8 µA in Sleep mode with RTCC and 30 nA in deep Sleep. According to the Microchip PIC24F16KL402 Family Data Sheet, the device supports ICD (In-Circuit Debug) via dedicated PG/RE pins and operates across -40 °C to +85 °C industrial temperature range.
Typical applications include low-cost medical disposables (testers, dispensers, inhalers), portable consumer electronics (media players, GPS accessories, cell phone peripherals, electronic toys and games), safety/security sensors, battery-powered sensor nodes, and home appliances. The wide peripheral mix allows designers to migrate existing PIC18 firmware while gaining 16-bit performance.
When designing with this part, plan for a 3.3 V core supply, place 0.1 µF decoupling near each VDD pin, and connect the exposed pad (where present) to the ground plane for thermal relief. The MSSP can be configured for either I2C or SPI but not both simultaneously; firmware must select one mode at runtime.
Alternatif penggantian untuk PIC24F16KL402-I/SS — paket yang sama, pin-pada-pin kompatibel. Bagian paket yang berbeda memerlukan kerja ulang PCB diabaikan.
Variasi di dalam seri ini
Model-series yang sama yang kompatibel dengan penggantian PIC24F16KL402-I/SS (sama faktor bentuk dan footprint) — berbeda di dalam Package, ADC, Operating Temperature, Data RAM, Timers.
PIC24F16KL402-E/SS
✅ Drop-InKontak untuk harga
Lihat Datasheet →PIC24F16KL401-I/SS
✅ Drop-In📋 Alternatif referensi (tidak dalam katalog)
PIC24F16KL402T-I/SS
✅ Drop-In📋 Alternatif referensi (tidak dalam katalog)
PIC24F16KL401T-I/EF
✅ Drop-In📋 Alternatif referensi (tidak dalam katalog)
PIC24F16KA304-I/SS
✅ Drop-In📋 Alternatif referensi (tidak dalam katalog)
PIC24F16KL402-I/SS Rating Maksimal & Karakteristik Listrik
| Core | PIC24F 16-bit RISC |
| Series | PIC24F16KL402, nanoWatt XLP |
| Program Memory (Flash) | 16 KB (5.5K x 24 words) |
| Data SRAM | 1 KB |
| Data EEPROM | Not present (0 B) |
| Maximum CPU Speed | 32 MHz (16 MIPS) |
| Supply Voltage (VDD) | 1.8 V to 3.6 V |
| Typical Operating Voltage | 3.3 V |
| A/D Converter | 10-bit, up to 12 channels, 500 ksps |
| Analog Comparators | 2 rail-to-rail with programmable I/O |
| Timers | 3 x 16-bit Timer/Counter |
| CCP/ECCP Modules | 1 x 16-bit CCP, 1 x ECCP |
| MSSP (I2C/SPI) | Yes (1 module) |
| UART | 1 x UART (per family data sheet) |
| General-Purpose I/O | Up to 25 GPIO |
| On-chip Voltage Reference | Yes |
| In-Circuit Debug | ICD via PG/RE pins |
| Paket | 28-pin SSOP (0.209" / 5.30 mm width) |
| Tipe Mounting | Surface Mount |
| Suhu Kerja | -40 °C to +85 °C (Industrial, 'I') |
| Status RoHS | Compliant |
Konfigurasi Pin PIC24F16KL402-I/SS
| Pin produk 1 | RP4/PMA0/CN4/RC4 — Remappable I/O / PMP address / interrupt-on-change |
| Pin produk 2 | RP5/PMA1/CN5/RC5 — Remappable I/O / PMP address / interrupt-on-change |
| Pin produk 3 | RP6/PMA2/CN6/RC6 — Remappable I/O / PMP address / interrupt-on-change |
| Pin produk 4 | RP7/PMA3/CN7/RC7 — Remappable I/O / PMP address / interrupt-on-change |
| Pin produk 5 | VSS — Ground reference |
| Pin produk 6 | OSC1/CLKI/RA1 — Crystal oscillator input or external clock |
| Pin produk 7 | OSC2/CLKO/RA2 — Crystal oscillator output or clock out |
| Pin produk 8 | VDD — Positive supply voltage (1.8-3.6V) |
| Pin produk 9 | PGD1/RP0/CN8/RC0 — ICD data / Remappable I/O / CN |
| Pin produk 10 | PGC1/RP1/CN9/RC1 — ICD clock / Remappable I/O / CN |
| Pin produk 11 | RP2/CN10/RC2 — Remappable I/O / interrupt-on-change |
| Pin produk 12 | RP3/CN11/RC3 — Remappable I/O / interrupt-on-change |
| Pin produk 13 | VSS — Ground reference |
| Pin produk 14 | VDD — Positive supply voltage (1.8-3.6V) |
| Pin produk 15 | TMS/RP8/CN12/RB8 — JTAG TMS / Remappable I/O |
| Pin produk 16 | TCK/RP9/CN13/RB9 — JTAG TCK / Remappable I/O |
| Pin produk 17 | TDO/RP10/CN14/RB10 — JTAG TDO / Remappable I/O |
| Pin produk 18 | TDI/RP11/CN15/RB11 — JTAG TDI / Remappable I/O |
| Pin produk 19 | RP12/AN12/CVREF/RB12 — Remappable I/O / ADC ch12 / CVREF output |
| Pin produk 20 | RP13/AN11/C1OUT/RB13 — Remappable I/O / ADC ch11 / Comparator 1 out |
| Pin produk 21 | RP14/AN10/C2OUT/RB14 — Remappable I/O / ADC ch10 / Comparator 2 out |
| Pin produk 22 | RP15/AN9/OCFB/RB15 — Remappable I/O / ADC ch9 / OC fault input |
| Pin produk 23 | AN8/RP3/CN17/RC3 — ADC ch8 / Remappable I/O (per datasheet) |
| Pin produk 24 | AN7/RP2/CN16/RC2 — ADC ch7 / Remappable I/O |
| Pin produk 25 | AN6/RP1/CN9/RC1 — ADC ch6 / Remappable I/O |
| Pin produk 26 | AN5/RP0/CN8/RC0 — ADC ch5 / Remappable I/O |
| Pin produk 27 | AN4/RP15/CN15/RB15 — ADC ch4 / Remappable I/O |
| Pin produk 28 | VSS — Ground reference |
Aplikasi Umum
PIC24F16KL402-I/SS cocok untuk 6 aplikasis: Low-Cost Medical Disposables, Portable Consumer Electronics, Safety and Security Sensors, Battery-Powered Sensor Nodes, Home Appliance Control, In-Circuit Debug-Ready Prototyping.
Low-Cost Medical Disposables
The PIC24F16KL402-I/SS suits disposable medical devices like single-use glucose testers, asthma inhalers, and pill dispensers where the XLP Sleep current below 1.8 µA extends coin-cell battery life beyond the shelf life of the consumable. Its 16-bit core supports accurate ADC processing for diagnostic sensors. The 28-SSOP keeps BOM under $3 in volume.
Direkomendasikan
Portable Consumer Electronics
The PIC24F16KL402-I/SS powers portable media players, GPS peripherals, cell phone accessories, and electronic toys/games where cost and battery life dominate the BOM. The 16 MIPS performance decodes audio frames in real time, while the 12-channel 10-bit ADC reads buttons and battery telemetry. XLP Sleep modes let the MCU spend 99% of the time idle.
Direkomendasikan
Safety and Security Sensors
The PIC24F16KL402-I/SS fits low-power PIR motion sensors, smoke alarms, and home security peripherals where standby current is critical to multi-year battery life. XLP deep Sleep below 30 nA keeps a 3 V coin cell alive for 10+ years. The dual analog comparators allow direct interfacing to PIR thermopiles and smoke-chamber amplifiers without extra ICs.
Direkomendasikan
Battery-Powered Sensor Nodes
Industrial IoT edge sensors using the PIC24F16KL402-I/SS leverage the MSSP I2C/SPI interface to read digital sensors like temperature, humidity, and accelerometers. The 16 KB Flash accommodates MQTT/HTTP or LoRaWAN stack fragments on small TCP networks. Sleep currents below 1.8 µA enable multi-year battery deployments on 2xAA cells.
Direkomendasikan
Home Appliance Control
The PIC24F16KL402-I/SS drives user-interface and timing tasks in small home appliances like coffee makers, kitchen timers, and air-quality monitors. The 16-bit ECCP module controls brushed DC motors and dimming LEDs. nanoWatt XLP architecture keeps standby power below 0.1 W, helping designs comply with EU standby regulations.
Direkomendasikan
In-Circuit Debug-Ready Prototyping
The PIC24F16KL402-I/SS supports MPLAB ICD via dedicated PG/RE pins on the 28-SSOP footprint, making it ideal for engineering prototypes and educational designs. The standard 0.65 mm SSOP pitch is breadboard-compatible via SSOP-to-DIP adapter PCBs. Combined with MPLAB X IDE and XC16 compiler, designers get a 16-bit upgrade path with minimal toolchain change.
Direkomendasikan
Ringkasan Produk Direkomendasikan
Data referensi engineering untuk PIC24F16KL402-I/SS — pembandingan, panduan desain, dan informasi konformitas.
Panduan Pemilihan
Pembandingan dengan Alternatif
| Parameter Umum | Produk Ini | PIC24F16KL402-I/SO | PIC24F16KL402-E/SS | PIC24F16KL401-I/SS | PIC24F16KL402T-I/SS | PIC24F16KL401T-I/EF | PIC24F16KA304-I/SS |
|---|---|---|---|---|---|---|---|
| Package | 28-SSOP (5.30 mm) | 28-SOIC (300 mil) | 28-SSOP (5.30 mm) - same | 28-SSOP (5.30 mm) - same | 28-SSOP (5.30 mm) - same | 28-SSOP (5.30 mm) - same | 28-SSOP (5.30 mm) - same |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Flash Memory | 16 KB | 16 KB | 16 KB | 8 KB | 16 KB | 8 KB | 16 KB (KA family) |
| SRAM | 1 KB | 1 KB | 1 KB | 1 KB | 1 KB | 1 KB | 2 KB |
| Core Frequency | 32 MHz / 16 MIPS | 32 MHz / 16 MIPS | 32 MHz / 16 MIPS | 32 MHz / 16 MIPS | 32 MHz / 16 MIPS | 32 MHz / 16 MIPS | 32 MHz / 16 MIPS |
| Operating Temperature | -40 to +85 °C (Industrial) | -40 to +85 °C (Industrial) | -40 to +125 °C (Extended) | -40 to +85 °C (Industrial) | -40 to +85 °C (Industrial) | -40 to +125 °C (Extended) | -40 to +85 °C (Industrial) |
| Core Architecture | PIC24F KL (XLP) | PIC24F KL (XLP) | PIC24F KL (XLP) | PIC24F KL (XLP) | PIC24F KL (XLP) | PIC24F KL (XLP) | PIC24F KA (older) |
Diferensiator Kunci
- True drop-in SSOP-28 form factor with nanoWatt XLP technology (vsPIC24F16KA304-I/SS)
- Industrial temperature range vs Extended temperature (vsPIC24F16KL402-E/SS)
- Same die, more Flash than PIC24F16KL401-I/SS (vsPIC24F16KL401-I/SS)
Catatan Desain
Estimated: at VDD=3.3V, CPU at 32 MHz / 16 MIPS, typical run current is ~4-5 mA; at Sleep with RTCC and WDT, XLP technology drops the current to ~1.8 µA. Place a 0.1 µF X7R decoupling capacitor within 5 mm of each VDD pin and a 10 µF bulk electrolytic or tantalum at the board's power entry. Configure the lowest-frequency oscillator needed by the design and disable unused peripherals in firmware to extend battery life.
The 28-SSOP uses a 0.65 mm pitch; route power and ground on inner planes to provide low-impedance references. Keep the analog AVSS / AGND pins tied to a clean ground plane, isolated from noisy digital returns. Place the ICD PG/RE pins at the edge of the board or on test-point pads accessible by the MPLAB ICD header for prototype bring-up; do not place resistors in series with PGD1 or PGC1 in production unless they are bypassed with 0 ohm jumpers.
Do not exceed 3.6 V on VDD; transients above 4 V can permanently damage the MCU. Always configure unused I/O as outputs driving low to minimize current draw. The MSSP can be either I2C or SPI - not both - so the firmware must select the desired mode and clock polarity at runtime. ADC accuracy depends on the on-chip voltage reference; for highest precision use the external CVREF pin or an external precision reference.
On 28-SSOP layouts, keep digital traces away from the analog AVCC / AVSS pair, especially around AN4-AN12. Use a guard trace or ground island if the analog inputs handle low-level sensor signals (<10 mV). For I2C, use 4.7 kΩ pull-up resistors at 100 kHz, or 2.2 kΩ for 400 kHz Fast Mode. For noise-immune UART RS-485 designs, add series ferrite beads on the bus lines and a TVS diode for surge protection.
Informasi Konformitas
RoHS compliant per Microchip product page. Not AEC-Q100 qualified - choose the 'E' suffix variant for extended temperature or AEC-Q100-grade PIC24F16KA family parts.
