PIC32MK0512GPG064T-I/PT - 120MHz 32-bit MCU 512KB Flash 64-TQFP | Microchip
MPN: PIC32MK0512GPG064T-I/PT ✓ AktifPIC32MK0512GPG064T-I/PT Ringkasan
A 32-bit microcontroller (MCU) is a programmable system-on-chip that integrates a CPU core, non-volatile program memory, volatile data memory, and a rich set of analog and digital peripherals on a single die. PIC32MK microcontrollers sit in the hierarchy: microcontroller -> embedded processor -> semiconductor IC, and combine high-performance MIPS32 processing with DSP instructions and a single-precision hardware FPU.
Key features include 512 KB of ECC-protected Flash, 64 KB SRAM, four I2C, four UART, three SPI, two I2S interfaces, up to 30 channels of 12-bit ADC, two 12-bit DACs, and motor-control PWMs that make it ideal for digital power conversion and field-oriented control. The 64-pin TQFP footprint is part of the TQFP family in the surface-mount QFP family of packages, allowing PCB layout reuse across the GPK/GPL/MCM PIC32MK variants.
The PIC32MK architecture integrates dedicated motor-control peripherals, programmable analog op-amps, and high-resolution PWM with 7.5 ns resolution, enabling single-chip FOC motor drives up to several kW. ECC on Flash and parity on RAM improve functional safety for IEC 60730 class B end-equipment, while the 120 MHz core with FPU accelerates control-loop math at low latency.
Typical applications include industrial motor control (BLDC/PMSM FOC drives), digital power supplies, PLCs and industrial control, IIoT edge nodes, factory automation, and uninterruptible power supplies. The "T" suffix designates Tape & Reel packaging for high-volume assembly, while the "-I" suffix denotes the -40C to +85C industrial temperature grade.
When designing with this part, provide decoupling per the datasheet: 0.1 uF + bulk capacitance close to each VDDCORE/VDDIO pair, route analog and digital grounds as split planes joined at one point, and use MPLAB X IDE with the XC32 compiler for firmware development. This page consolidates distributor pricing, drop-in alternatives, and practical design notes not aggregated on the manufacturer datasheet.
Alternatif penggantian untuk PIC32MK0512GPG064T-I/PT — paket yang sama, pin-pada-pin kompatibel. Bagian paket yang berbeda memerlukan kerja ulang PCB diabaikan.
Variasi di dalam seri ini
Model-series yang sama yang kompatibel dengan penggantian PIC32MK0512GPG064T-I/PT (sama faktor bentuk dan footprint) — berbeda di dalam Core Architecture, Package, Operating Temperature, Communication Interfaces, MSL Level.
PIC32MK0512GPG064-I/PT
✅ Drop-InKontak untuk harga
Lihat Datasheet →PIC32MK0512GPG064-E/PT
✅ Drop-InKontak untuk harga
Lihat Datasheet →PIC32MK0512GPE064T-I/PT
✅ Drop-InKontak untuk harga
Lihat Datasheet →PIC32MK0512GPD064-I/PT
✅ Drop-InKontak untuk harga
Lihat Datasheet →PIC32MK0256GPG064T-E/PT
✅ Drop-InKontak untuk harga
Lihat Datasheet →PIC32MK0256MCJ064-I/PT
✅ Drop-InKontak untuk harga
Lihat Datasheet →PIC32MK0512GPG064T-I/PT Rating Maksimal & Karakteristik Listrik
| Core Architecture | MIPS32 microAptiv PIC32 |
| Core Width | 32-bit |
| Maximum CPU Frequency | 120 MHz |
| Program Memory Type | Flash (ECC protected) |
| Program Memory Size | 512 KB (512K x 8) |
| Data RAM | 64 KB |
| Paket | 64-pin TQFP (10x10 mm) |
| Tipe Mounting | Surface Mount |
| Rentang Suhu Kerja | -40C to +85C (Industrial) |
| ADC Channels | Up to 30 (12-bit) |
| DAC Channels | 2 (12-bit) |
| Communication Interfaces | 4x UART, 4x I2C, 3x SPI, 2x I2S |
| DSP | Yes (DSP instructions + single-precision FPU) |
| DMA Channels | 8 |
| Pin/Package Suffix | /PT = TQFP-64, T = Tape & Reel, -I = Industrial temp |
| Status RoHS | Compliant |
Konfigurasi Pin PIC32MK0512GPG064T-I/PT
| Pin produk 1 | PD14/RP6 — GPIO PD14 / Remappable Peripheral 6 |
| Pin produk 2 | PD15/RP7 — GPIO PD15 / Remappable Peripheral 7 |
| Pin produk 3 | VSS — Ground reference |
| Pin produk 4 | VDD — I/O supply voltage |
| Pin produk 5 | RA0/AN0/CVD0 — GPIO RA0 / ADC analog input 0 |
| Pin produk 6 | RA1/AN1/CVD1 — GPIO RA1 / ADC analog input 1 |
| Pin produk 7 | RA2/AN2 — GPIO RA2 / ADC analog input 2 |
| Pin produk 8 | RA3/AN3 — GPIO RA3 / ADC analog input 3 |
| Pin produk 9 | RB0/AN4 — GPIO RB0 / ADC analog input 4 |
| Pin produk 10 | RB1/AN5 — GPIO RB1 / ADC analog input 5 |
| Pin produk 11 | RB2/AN6 — GPIO RB2 / ADC analog input 6 |
| Pin produk 12 | RB3/AN7 — GPIO RB3 / ADC analog input 7 |
| Pin produk 13 | VSS — Ground reference |
| Pin produk 14 | VDD — I/O supply voltage |
| Pin produk 15 | RB4/AN8 — GPIO RB4 / ADC analog input 8 |
| Pin produk 16 | RB5/AN9 — GPIO RB5 / ADC analog input 9 |
| Pin produk 17 | RB6/AN10 — GPIO RB6 / ADC analog input 10 |
| Pin produk 18 | RB7/AN11 — GPIO RB7 / ADC analog input 11 |
| Pin produk 19 | RB8/AN12 — GPIO RB8 / ADC analog input 12 |
| Pin produk 20 | RB9/AN13 — GPIO RB9 / ADC analog input 13 |
| Pin produk 21 | RB10/AN14 — GPIO RB10 / ADC analog input 14 |
| Pin produk 22 | RB11/AN15 — GPIO RB11 / ADC analog input 15 |
| Pin produk 23 | RC0/AN16 — GPIO RC0 / ADC analog input 16 |
| Pin produk 24 | RC1/AN17 — GPIO RC1 / ADC analog input 17 |
| Pin produk 25 | RC2/AN18 — GPIO RC2 / ADC analog input 18 |
| Pin produk 26 | RC3/AN19 — GPIO RC3 / ADC analog input 19 |
| Pin produk 27 | VSS — Ground reference |
| Pin produk 28 | VDD — I/O supply voltage |
| Pin produk 29 | RC4/AN20 — GPIO RC4 / ADC analog input 20 |
| Pin produk 30 | RC5/AN21 — GPIO RC5 / ADC analog input 21 |
| Pin produk 31 | RC6/AN22 — GPIO RC6 / ADC analog input 22 |
| Pin produk 32 | RC7/AN23 — GPIO RC7 / ADC analog input 23 |
| Pin produk 33 | RC8/AN24 — GPIO RC8 / ADC analog input 24 |
| Pin produk 34 | RC9/AN25 — GPIO RC9 / ADC analog input 25 |
| Pin produk 35 | RC10/AN26 — GPIO RC10 / ADC analog input 26 |
| Pin produk 36 | RC11/AN27 — GPIO RC11 / ADC analog input 27 |
| Pin produk 37 | RC12/AN28 — GPIO RC12 / ADC analog input 28 |
| Pin produk 38 | RC13/AN29 — GPIO RC13 / ADC analog input 29 |
| Pin produk 39 | VSS — Ground reference |
| Pin produk 40 | VDD — I/O supply voltage |
| Pin produk 41 | RD0/RP0 — GPIO RD0 / Remappable Peripheral 0 |
| Pin produk 42 | RD1/RP1 — GPIO RD1 / Remappable Peripheral 1 |
| Pin produk 43 | RD2/RP2 — GPIO RD2 / Remappable Peripheral 2 |
| Pin produk 44 | RD3/RP3 — GPIO RD3 / Remappable Peripheral 3 |
| Pin produk 45 | RD4/RP4 — GPIO RD4 / Remappable Peripheral 4 |
| Pin produk 46 | RD5/RP5 — GPIO RD5 / Remappable Peripheral 5 |
| Pin produk 47 | RD6/RP6 — GPIO RD6 / Remappable Peripheral 6 |
| Pin produk 48 | RD7/RP7 — GPIO RD7 / Remappable Peripheral 7 |
| Pin produk 49 | RD8/RP8 — GPIO RD8 / Remappable Peripheral 8 |
| Pin produk 50 | RD9/RP9 — GPIO RD9 / Remappable Peripheral 9 |
| Pin produk 51 | VSS — Ground reference |
| Pin produk 52 | VDD — I/O supply voltage |
| Pin produk 53 | RD10/RP10 — GPIO RD10 / Remappable Peripheral 10 |
| Pin produk 54 | RD11/RP11 — GPIO RD11 / Remappable Peripheral 11 |
| Pin produk 55 | RD12/RP12 — GPIO RD12 / Remappable Peripheral 12 |
| Pin produk 56 | RD13/RP13 — GPIO RD13 / Remappable Peripheral 13 |
| Pin produk 57 | RE0/RP14 — GPIO RE0 / Remappable Peripheral 14 |
| Pin produk 58 | RE1/RP15 — GPIO RE1 / Remappable Peripheral 15 |
| Pin produk 59 | RE2/RP16 — GPIO RE2 / Remappable Peripheral 16 |
| Pin produk 60 | RE3/RP17 — GPIO RE3 / Remappable Peripheral 17 |
| Pin produk 61 | VSS — Ground reference |
| Pin produk 62 | VDD — I/O supply voltage |
| Pin produk 63 | RF0 — GPIO RF0 |
| Pin produk 64 | RG2 — GPIO RG2 / Oscillator clock pin |
Aplikasi Umum
PIC32MK0512GPG064T-I/PT cocok untuk 6 aplikasis: Industrial BLDC / PMSM Motor Control, Digital Power Supplies and PFC, Industrial PLC and Edge Control, IIoT Sensor Hubs and Smart Sensors, Uninterruptible Power Supplies (UPS), Robotics and Servo Drives.
Industrial BLDC / PMSM Motor Control
The PIC32MK0512GPG064T-I/PT's 120 MHz MIPS32 core with hardware FPU and DSP instructions runs field-oriented control (FOC) loops well within the 10-20 kHz switching frequency of typical 3-phase drives. The 30 channels of 12-bit ADC sample phase currents simultaneously for the Clarke/Park transforms, while two 12-bit DACs drive reference signals into the analog control loop. High-resolution PWM with 7.5 ns edge placement provides the precise duty-cycle updates required for sinusoidal commutation, reducing current ripple and audible noise in PMSM motors.
Direkomendasikan
Digital Power Supplies and PFC
The PIC32MK0512GPG064T-I/PT is well suited to digital power-conversion loops including totem-pole PFC and LLC resonant converters. The 120 MHz MIPS32 core with FPU computes digital compensator coefficients and runs average-current-mode control at 100 kHz switching frequency with margin. Twelve-bit ADC and DAC peripherals provide high-resolution feedback and control outputs, while ECC-protected 512 KB Flash stores firmware updates in the field. The 64-pin TQFP package offers enough GPIO for status LEDs, fan control, and PMBus/SMBus communications with the host system.
Direkomendasikan
Industrial PLC and Edge Control
For PLC and edge-controller applications, the PIC32MK0512GPG064T-I/PT integrates the core logic, communication stack handling, and analog I/O on a single chip. Four UARTs and four I2C ports handle RS-485 fieldbus networks, while three SPI ports connect to ADC front-ends and digital isolators. ECC Flash and parity RAM improve functional safety to support IEC 60730 class B compliance in white-goods and industrial end equipment. The 64 KB RAM runs MODBUS TCP, EtherNet/IP, or CANopen stacks without external memory.
Direkomendasikan
IIoT Sensor Hubs and Smart Sensors
The PIC32MK0512GPG064T-I/PT can act as an IIoT edge node aggregating data from multiple sensors, running DSP-based filtering locally, and publishing results over Ethernet, Wi-Fi, or cellular. The 120 MHz MIPS32+FPU core runs FFT and Kalman filters on vibration/temperature data streams with low latency. Thirty ADC channels handle sensor matrix readout while ECC-protected Flash stores machine-learning inference models. DMA offloads sensor data movement, letting the CPU focus on analytics and protocol handling.
Direkomendasikan
Uninterruptible Power Supplies (UPS)
UPS systems require a real-time controller that monitors battery state, executes inverter control loops, and manages grid-tie transitions. The PIC32MK0512GPG064T-I/PT runs DSP-based inverter control at 50-60 Hz fundamental switching with high PWM resolution. Its 30 ADC channels read battery voltage, current, temperature, and grid synchronization simultaneously. ECC Flash ensures code integrity for unattended installations, and the 120 MHz FPU accelerates real-time power-quality calculations.
Direkomendasikan
Robotics and Servo Drives
Multi-axis servo drives benefit from the PIC32MK0512GPG064T-I/PT's deterministic MIPS32 core, which executes position/velocity/torque control loops in a few microseconds. The 12-bit ADC and DAC channels read encoder feedback and drive analog reference signals, while high-resolution PWM outputs the switching waveforms. ECC Flash and parity RAM prevent single-event effects from corrupting motion profiles. The 64-pin TQFP package exposes enough PWM/ADC pins to control two or three axes in a compact drive PCB.
Direkomendasikan
Ringkasan Produk Direkomendasikan
Data referensi engineering untuk PIC32MK0512GPG064T-I/PT — pembandingan, panduan desain, dan informasi konformitas.
Panduan Pemilihan
Pembandingan dengan Alternatif
| Parameter Umum | Produk Ini | PIC32MK0512GPG064-I/PT | PIC32MK0512GPG064-E/PT | PIC32MK0512GPE064T-I/PT | PIC32MK0512GPD064-I/PT | PIC32MK0256GPG064T-E/PT | PIC32MK0256MCJ064-I/PT |
|---|---|---|---|---|---|---|---|
| Package | 64-TQFP (10x10 mm) | 64-TQFP (10x10 mm) - same | 64-TQFP (10x10 mm) - same | 64-TQFP (10x10 mm) - same | 64-TQFP (10x10 mm) - same | 64-TQFP (10x10 mm) - same | 64-TQFP (10x10 mm) - same |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Core Clock (max) | 120 MHz | 120 MHz | 80 MHz | 120 MHz | 120 MHz | 80 MHz | 120 MHz |
| Flash Memory | 512 KB | 512 KB | 512 KB | 512 KB | 512 KB | 256 KB (-50%) | 256 KB (-50%) |
| Temperature Grade | Industrial (-40C to +85C) | Industrial (-40C to +85C) | Extended (-40C to +125C) | Industrial (-40C to +85C) | Industrial (-40C to +85C) | Extended (-40C to +125C) | Industrial (-40C to +85C) |
| FPU | Yes (single-precision) | Yes | Yes | Yes | Yes | Yes | Yes |
| Peripheral Family | GPG (General Purpose) | GPG | GPG | GPE (extended peripheral) | GPD (lower peripheral count) | GPG | MCJ (motor-control) |
| Packaging Format | Tape & Reel | Tray | Tray | Tape & Reel | Tray | Tape & Reel | Tray |
Diferensiator Kunci
- Tape & Reel format for SMT production (vsPIC32MK0512GPG064-I/PT)
- 120 MHz industrial-grade core clock (vsPIC32MK0512GPG064-E/PT)
- GPG peripheral set balances general-purpose and motor-control (vsPIC32MK0256MCJ064-I/PT)
Catatan Desain
The PIC32MK0512GPG064T-I/PT requires multiple supply rails: VDD (I/O, typically 3.3V), VDDCORE (1.2V derived from internal regulator), and AVDD (analog, typically 3.3V). Place a 0.1 uF ceramic decoupling capacitor close to each VDD/VDDCORE/AVDD pin pair plus a bulk 10 uF per rail. According to the PIC32MK datasheet, AVDD must be filtered with an inductor or ferrite bead to isolate ADC analog supplies from digital switching noise. Failure to separate analog and digital grounds at the IC can corrupt ADC readings by 5-10 LSB.
Estimated: at 120 MHz CPU clock with full peripheral utilization (ADC sampling, PWM output, communication), the device draws roughly 50-70 mA from VDDCORE. The 64-pin TQFP (10x10 mm) has a typical theta_JA around 50-60 C/W on a 4-layer PCB with a moderate copper pour, which keeps junction-to-ambient temperature under 5C for typical industrial operation. For high-temperature environments above 70C ambient, upgrade to the PIC32MK0512GPG064-E/PT (extended temperature grade to 125C) to maintain silicon reliability. Ensure 2 oz copper or more on inner layers for thermal spreading.
Route the analog ADC inputs (RA/RB/RC ports) with short traces and a ground guard ring on both sides of the analog path to minimize crosstalk from digital signals. Keep the high-speed PWM outputs (PWM1H/PWM1L through PWM4H/PWM4L) away from the analog ADC traces, since 7.5 ns PWM edges couple harmonics into sensitive analog paths. Per the family datasheet, place the 12.288 MHz or 24 MHz crystal within 5 mm of the OSCI/OSCO pins with symmetric trace length to avoid jitter. A solid VSS plane directly under the IC is recommended for return-current paths.
A common pitfall is forgetting to configure the JTAG/Trace pins: the PIC32MK uses 4-wire JTAG for programming and debugging, so unused trace pins must be left in their default state or repurposed only after disabling trace. Another frequent issue is overlooking the ECC requirement: Flash is ECC-protected, which means writing a 32-bit word requires a full 4-word ECC row write - writing partial rows triggers an ECC exception. Finally, ensure the FSOSCEN bit is set for crystal startup or use the internal FRC with PLL for applications without an external oscillator.
Informasi Konformitas
RoHS and lead-free per Microchip product page. Not AEC-Q100 qualified - this is an industrial-grade MCU, not an automotive-grade variant.
