PIC32MX440F512H-80I/PT - 32-bit MCU 80MHz 512KB Flash USB-OTG TQFP-64
MPN: PIC32MX440F512H-80I/PT ✓ AktifPIC32MX440F512H-80I/PT Ringkasan
A 32-bit MCU (microcontroller unit) is a single-chip computer that combines a 32-bit processor core, program memory (Flash), data memory (SRAM), and a rich set of peripherals (ADC, timers, communication interfaces). PIC32 microcontrollers are part of the MIPS32 family, positioning them above 8-bit PIC MCUs and below 32-bit Cortex-M ARM devices in the embedded hierarchy. They are well suited for USB, graphics, and connectivity applications requiring deterministic real-time behavior combined with high throughput.
Key features of the PIC32MX440F512H-80I/PT include 80 MHz / 105 DMIPS CPU performance, 512 KB Flash program memory, 32 KB SRAM data memory, integrated USB-OTG with PHY, 5-stage pipeline Harvard architecture, MIPS16e code compression for up to 40% smaller code, hardware multiply/divide unit, 16-bit wide instructions, dedicated DMA controller, and a 10-bit ADC with up to 1 Msps sampling.
The architecture combines a 5-stage pipeline, Harvard bus layout, and a high-bandwidth peripheral bus. The on-chip DMA engine can move data between peripherals and memory without CPU intervention, freeing the core for control loops and protocol handling. The integrated USB-OTG PHY eliminates external transceivers, reducing BOM cost on USB-equipped embedded products.
Typical applications include industrial control panels, USB peripherals (HID, CDC, mass storage), embedded graphics with external TFT controllers, automotive body electronics, point-of-sale terminals, medical instrumentation, and consumer audio devices. The wide operating voltage range (2.3 V to 3.6 V) simplifies battery-powered designs.
When designing with this device, ensure that the ICSP trace length between the programming connector and the PGECx/PGEDx pins is minimized to maintain reliable in-circuit serial programming. Decoupling capacitors (0.1 uF + bulk) must be placed close to VDD/AVDD pins.
This page synthesizes distributor pricing, drop-in compatible alternatives from the same PIC32MX family, and practical design notes not found in the standalone datasheet to accelerate your component selection.
Alternatif penggantian untuk PIC32MX440F512H-80I/PT — paket yang sama, pin-pada-pin kompatibel. Bagian paket yang berbeda memerlukan kerja ulang PCB diabaikan.
Tidak ada alternatif pengganti yang tersedia untuk produk ini.
Permintaan AlternatifPIC32MX440F512H-80I/PT Rating Maksimal & Karakteristik Listrik
| Core Architecture | MIPS32 M4K 32-bit |
| CPU Speed | 80 MHz |
| DMIPS Performance | 105 DMIPS |
| Program Memory (Flash) | 512 KB (512K x 8) |
| Data Memory (SRAM) | 32 KB |
| Supply Voltage (VDD) | 2.3 V to 3.6 V |
| I/O Pins | 51 |
| USB Interface | USB 2.0 On-The-Go with integrated PHY |
| ADC | 10-bit, up to 1 Msps, 16 channels |
| DMA Channels | Dedicated DMA (4 channels) |
| Timers | 5 x 16-bit timers/counters |
| Communication Interfaces | 2x UART, 2x SPI, 2x I2C |
| Suhu Kerja | -40 C to +85 C (Industrial) |
| Paket | 64-pin TQFP (10x10 mm) |
| Tipe Mounting | Surface Mount |
| Level MSL | 3 (168 hours) |
| Status RoHS | Compliant |
| Instruction Set | MIPS32 with MIPS16e code compression |
Konfigurasi Pin PIC32MX440F512H-80I/PT
| Pin produk 1 | RPB0/AN0 — Remappable I/O, Analog input 0 |
| Pin produk 2 | RPB1/AN1 — Remappable I/O, Analog input 1 |
| Pin produk 3 | RPB2/AN2/CVREF — Remappable I/O, Analog input 2, CVREF output |
| Pin produk 4 | RPB3/AN3 — Remappable I/O, Analog input 3 |
| Pin produk 5 | VREF-/RA9 — ADC VREF- or GPIO |
| Pin produk 6 | VREF+/RA10 — ADC VREF+ or GPIO |
| Pin produk 7 | AVDD — Analog supply voltage |
| Pin produk 8 | AVSS — Analog ground |
| Pin produk 9 | RPB4/AN4 — Remappable I/O, Analog input 4 |
| Pin produk 10 | RPB5/AN5 — Remappable I/O, Analog input 5 |
| Pin produk 11 | RPB6/AN6/PGEC2 — Remappable I/O, AN6, ICSP clock 2 |
| Pin produk 12 | RPB7/AN7/PGED2 — Remappable I/O, AN7, ICSP data 2 |
| Pin produk 13 | RC1 — Remappable I/O |
| Pin produk 14 | RC2 — Remappable I/O |
| Pin produk 15 | RC3 — Remappable I/O |
| Pin produk 16 | RC4 — Remappable I/O |
| Pin produk 17 | VSS — Digital ground |
| Pin produk 18 | VDD — Digital supply voltage |
| Pin produk 19 | PGEC1/RC5 — ICSP clock 1 or GPIO |
| Pin produk 20 | PGED1/RC6 — ICSP data 1 or GPIO |
| Pin produk 21 | RC7 — Remappable I/O |
| Pin produk 22 | RC8 — Remappable I/O |
| Pin produk 23 | RC9 — Remappable I/O |
| Pin produk 24 | VSS — Digital ground |
| Pin produk 25 | VDD — Digital supply voltage |
| Pin produk 26 | RPB8/AN8 — Remappable I/O, Analog input 8 |
| Pin produk 27 | RPB9/AN9 — Remappable I/O, Analog input 9 |
| Pin produk 28 | RPB10/AN10 — Remappable I/O, Analog input 10 |
| Pin produk 29 | RPB11/AN11 — Remappable I/O, Analog input 11 |
| Pin produk 30 | VSS — Digital ground |
| Pin produk 31 | VDD — Digital supply voltage |
| Pin produk 32 | VSS — Digital ground |
| Pin produk 33 | VDD — Digital supply voltage |
| Pin produk 34 | RPB12/AN12 — Remappable I/O, Analog input 12 |
| Pin produk 35 | RPB13/AN13 — Remappable I/O, Analog input 13 |
| Pin produk 36 | RPB14/AN14 — Remappable I/O, Analog input 14 |
| Pin produk 37 | RPB15/AN15/OCFB — Remappable I/O, AN15, Output Compare Fault B |
| Pin produk 38 | VSS — Digital ground |
| Pin produk 39 | VDD — Digital supply voltage |
| Pin produk 40 | RA0 — Remappable I/O |
| Pin produk 41 | RA1 — Remappable I/O |
| Pin produk 42 | RA2 — Remappable I/O |
| Pin produk 43 | RA3 — Remappable I/O |
| Pin produk 44 | RA4 — Remappable I/O |
| Pin produk 45 | RA5 — Remappable I/O |
| Pin produk 46 | RA6 — Remappable I/O |
| Pin produk 47 | RA7 — Remappable I/O |
| Pin produk 48 | VSS — Digital ground |
| Pin produk 49 | VDD — Digital supply voltage |
| Pin produk 50 | RD0 — Remappable I/O |
| Pin produk 51 | RD1 — Remappable I/O |
| Pin produk 52 | RD2 — Remappable I/O |
| Pin produk 53 | RD3 — Remappable I/O |
| Pin produk 54 | RD4 — Remappable I/O |
| Pin produk 55 | RD5 — Remappable I/O |
| Pin produk 56 | RD6 — Remappable I/O |
| Pin produk 57 | RD7 — Remappable I/O |
| Pin produk 58 | VSS — Digital ground |
| Pin produk 59 | RD8 — Remappable I/O |
| Pin produk 60 | RD9 — Remappable I/O |
| Pin produk 61 | RD10 — Remappable I/O |
| Pin produk 62 | RD11 — Remappable I/O |
| Pin produk 63 | RD12 — Remappable I/O |
| Pin produk 64 | RD13 — Remappable I/O |
| Pin produk exposed_pad | VSS — Ground (exposed thermal pad, must be soldered to PCB ground) |
Aplikasi Umum
PIC32MX440F512H-80I/PT cocok untuk 6 aplikasis: USB HID Peripheral Devices, Industrial Control Panels, Embedded Data Acquisition Systems, USB-to-UART Bridge Devices, Consumer Audio Processing, Medical Instrumentation.
USB HID Peripheral Devices
The PIC32MX440F512H-80I/PT is an excellent fit for USB Human Interface Devices such as keyboards, mice, game controllers, and custom HID input devices. Its integrated USB-OTG controller with on-chip PHY eliminates the external transceiver, while the dedicated DMA channel handles USB endpoint transfers without CPU intervention. At 80 MHz and 105 DMIPS, the M4K core can parse HID reports, debounce inputs, and execute LED animations concurrently without jitter. The 512 KB Flash accommodates full USB stacks and custom descriptors. Place the USB D+/D- traces as a 90-ohm differential pair with matched length to maintain signal integrity per USB 2.0 specification.
Direkomendasikan
Industrial Control Panels
For industrial control panels with HMI touchscreens, the PIC32MX440F512H-80I/PT delivers 80 MHz performance to drive TFT LCDs via Parallel Master Port or SPI, while USB-OTG enables field firmware updates. The 512 KB Flash stores complete Modbus, EtherNet/IP, or CANopen protocol stacks alongside HMI graphics. The -40 C to +85 C industrial temperature rating ensures operation in factory environments. Its dedicated DMA channels handle ADC scanning of sensor inputs at 1 Msps while the CPU processes the HMI loop without dropping samples, providing deterministic control loop response. Add TVS protection on USB and external lines for surge immunity.
Direkomendasikan
Embedded Data Acquisition Systems
The PIC32MX440F512H-80I/PT is well suited for multi-channel data acquisition systems requiring simultaneous sampling and high throughput. Its 10-bit ADC with 16 input channels and 1 Msps sample rate, combined with dedicated DMA, can capture multi-sensor data streams into SRAM without CPU intervention. The 80 MHz CPU then post-processes, filters, and transmits via USB-OTG to a host PC at high speed. With 32 KB SRAM buffering and 512 KB Flash for FFT or DSP routines, the MCU handles vibration analysis, temperature logging, or power monitoring applications. Use external op-amps to buffer analog inputs and add RC anti-aliasing filters before the ADC pins.
Direkomendasikan
USB-to-UART Bridge Devices
The PIC32MX440F512H-80I/PT functions as a high-performance USB-to-UART bridge, replacing FTDI-style converters with a fully programmable solution. Its USB-OTG controller enumerates as a CDC-ACM or vendor-class device, while two UART peripherals provide serial data at speeds up to 20 Mbps. The 80 MHz CPU easily handles baud rates above 1 Mbps without data loss, and 512 KB Flash stores CDC stack plus custom protocol layers. This design fits industrial converters, debug loggers, and IoT gateways that need USB host connectivity to legacy RS-232/485 devices. The dedicated DMA can offload UART FIFO servicing to maintain zero-overhead flow control.
Direkomendasikan
Consumer Audio Processing
The PIC32MX440F512H-80I/PT handles USB Audio Class 1.0 devices including USB speakers, headsets, and DAC interfaces. Its 80 MHz MIPS32 M4K core processes audio streams at 48 kHz sample rate with headroom for DSP effects such as equalization or 3D spatialization. USB-OTG delivers isochronous audio at full-speed 12 Mbps, while I2S or SPI connects to external DACs like the PCM5102A. The 32 KB SRAM buffers USB audio packets, and 512 KB Flash stores USB descriptors plus DSP code. Use DMA to move audio samples between USB endpoint memory and I2S transmit registers, minimizing CPU load.
Direkomendasikan
Medical Instrumentation
The PIC32MX440F512H-80I/PT suits medical instrumentation such as portable spirometers, pulse oximeters, and point-of-care diagnostic devices. Its USB-OTG enables data upload to clinician PCs, while the 10-bit ADC captures analog sensor signals from instrumentation amplifiers. The 80 MHz core runs real-time filtering algorithms on sensor data, and 512 KB Flash stores calibration tables and patient record data structures. Industrial temperature rating supports clinical environments. Add optocouplers on any mains-connected portions for patient isolation per IEC 60601, and ensure firmware follows FDA cybersecurity guidance for connected medical devices.
Direkomendasikan
Ringkasan Produk Direkomendasikan
Data referensi engineering untuk PIC32MX440F512H-80I/PT — pembandingan, panduan desain, dan informasi konformitas.
Panduan Pemilihan
Pembandingan dengan Alternatif
| Parameter Umum | Produk Ini | PIC32MX440F512H-80I/MR |
|---|---|---|
| Package | 64-pin TQFP (10x10 mm) | 64-pin QFN (9x9 mm) |
| Brand | Microchip Technology | Microchip Technology |
| Core | MIPS32 M4K 32-bit | MIPS32 M4K 32-bit |
| CPU Speed | 80 MHz | 80 MHz |
| Flash Memory | 512 KB | 512 KB |
| SRAM | 32 KB | 32 KB |
| USB-OTG | Yes (integrated PHY) | Yes (integrated PHY) |
| ADC | 10-bit, 16-ch, 1 Msps | 10-bit, 16-ch, 1 Msps |
| Operating Voltage | 2.3 V to 3.6 V | 2.3 V to 3.6 V |
Diferensiator Kunci
- Integrated USB-OTG with PHY and dedicated DMA (vsPIC32MX460F512L)
- Cost-optimized 64-pin TQFP with USB (vsPIC32MX795F512L (100-pin TQFP))
- MIPS16e code compression saves Flash (vsGeneric ARM Cortex-M0 MCU)
Catatan Desain
Decoupling: Place 0.1 uF ceramic capacitors as close as possible to each VDD/AVDD pin pair, plus a single 10 uF bulk capacitor near the MCU. The exposed thermal pad on QFN variants must be soldered to a PCB ground pad with multiple thermal vias to a ground plane for heat dissipation. USB D+/D- traces should be a 90-ohm differential pair routed on the top layer over a continuous ground plane per the Microchip PIC32MX3XX/4XX family datasheet routing guidelines.
ICSP trace length: Keep traces between the ICSP programming connector (PGEC1/PGED1) and the MCU pins shorter than 50 mm (about 2 inches) to ensure reliable in-circuit serial programming. If the connector must be far from the MCU, add a series 100-ohm resistor near the MCU pin to dampen ringing. Do not share PGECx/PGEDx pins with high-speed switching signals without proper isolation. Estimate: trace propagation delay at ~5 ns/m and impedance mismatch can cause programming failures above ~100 mm.
Power sequencing: Apply VDD before or simultaneously with AVDD. The internal core regulator derives 1.8 V from VDD; if VDD drops below 2.0 V, the regulator cannot guarantee core logic operation. Add a 10 uF bulk capacitor on the MCU VDD rail with a 0.1 uF ceramic bypass. For USB applications, ensure VDD stays above 3.0 V during USB enumeration to meet USB electrical specifications per the Microchip datasheet. Estimated: total current draw at 80 MHz with USB active is approximately 70-85 mA.
Configuration words must be set correctly: disable JTAG if using all pins as GPIO, enable the appropriate oscillator mode (HS or XT with correct PLL settings for 80 MHz), and configure the alternate-pin function mapping via PPS (Peripheral Pin Select). Mistakenly leaving the JTAG enabled consumes four I/O pins. Wrong PLL configuration causes the MCU to run at half speed or fail to start. Always verify configuration bits in the IDE's configuration window before programming.
Informasi Konformitas
RoHS and REACH compliant per Microchip product page. Industrial temperature grade -40C to +85C; not AEC-Q100 qualified - choose PIC32MX variants with automotive qualification for vehicle applications.
