S912XEQ384J3CAL - 16-bit 384KB Flash MCU, 112-LQFP | NXP
MPN: S912XEQ384J3CAL ✓ AktifS912XEQ384J3CAL Ringkasan
An MCU (microcontroller) is a single-chip computer that integrates a CPU core, non-volatile program memory (Flash/ROM), volatile working memory (RAM), and a rich set of peripherals such as timers, ADC, communication controllers, and GPIO. It belongs to the hierarchy: microcontroller -> embedded processor -> semiconductor. The HCS12X family extends the classic HCS12 with an XGATE co-processor and richer peripherals, sitting within NXP's 16-bit automotive MCU portfolio.
Key features include an XGATE co-processor for offloading interrupt-driven virtual peripherals, hardware-emulated EEPROM capability that reduces external memory cost, a 12-bit ADC with 3 us conversion time, an Enhanced Capture Timer (ECT), Periodic Interrupt Timer (PIT), Real-Time Interrupt (RTI), and a Memory Protection Unit for system integrity. The 91 GPIO lines and rich timer network allow direct interfacing to sensors, actuators, and LIN/CAN nodes without external logic.
Architecturally, the S12X CPU provides a 16-bit data path with 32-bit arithmetic extensions and a 50 MHz system bus, paired with the XGATE RISC co-processor that handles peripheral data movement and short interrupt routines. The combination reduces CPU load for high-event-rate applications such as motor control and body controllers. Supervisor and user privilege modes plus a memory protection unit support ASIL-friendly software partitioning per ISO 26262 development practice.
Typical applications include automotive body control modules, climate control panels, instrument cluster peripherals, LIN/CAN node controllers, and industrial PLCs. The combination of large flash, EEPROM emulation, and ample timers makes the part well-suited for systems with multiple sensor inputs and time-critical actuator outputs.
When designing with the S912XEQ384J3CAL, ensure the operating temperature grade (industrial -40 C to +85 C for the J suffix) matches the target environment and place decoupling capacitors close to each VDD/VSS pair. Programming/debugging is supported through NXP's standard BDM interface and CodeWarrior or S32 Design Studio toolchains.
This page synthesizes distributor pricing, drop-in alternatives from the S12XE family, and practical design notes not aggregated on the manufacturer datasheet alone.
Alternatif penggantian untuk S912XEQ384J3CAL — paket yang sama, pin-pada-pin kompatibel. Bagian paket yang berbeda memerlukan kerja ulang PCB diabaikan.
Variasi di dalam seri ini
Model-series yang sama yang kompatibel dengan penggantian S912XEQ384J3CAL (sama faktor bentuk dan footprint) — berbeda di dalam Package, Operating Temperature, Flash Memory, Core, Co-Processor.
MC9S12XEQ384CAG
✅ Drop-InKontak untuk harga
Lihat Datasheet →S912XEG384J2VAL
✅ Drop-InKontak untuk harga
Lihat Datasheet →S912XET512BMAGR
✅ Drop-InKontak untuk harga
Lihat Datasheet →S912XET512J2VAGR
✅ Drop-InKontak untuk harga
Lihat Datasheet →S912XET256J2VAG
✅ Drop-InKontak untuk harga
Lihat Datasheet →S9S12XF384J2MLMR
✅ Drop-InKontak untuk harga
Lihat Datasheet →S912XEQ384J3CAL Rating Maksimal & Karakteristik Listrik
| Core | S12X (16-bit HCS12X family) |
| Bus Speed | 50 MHz |
| Program Memory (Flash) | 384 KB (384K x 8) |
| RAM Size | 24 KB |
| EEPROM Emulation | Yes (hardware-emulated EEE) |
| Number of I/O | 91 |
| Paket | 112-LQFP (20x20 mm) |
| Tipe Mounting | Surface Mount |
| Terminal Form | GULL WING |
| No. of Terminals | 112 |
| Suhu Kerja | -40 C to +85 C (industrial, J grade) |
| ADC Resolution | 12-bit |
| ADC Conversion Time | 3 us |
| Co-Processor | XGATE peripheral co-processor |
| Memory Protection Unit | Yes (supervisor/user modes) |
| Peripherals | ECT, PIT, RTI |
| Status RoHS | Compliant |
Konfigurasi Pin S912XEQ384J3CAL
| Pin produk 1 | VDDR — Voltage regulator supply |
| Pin produk 2 | VDD1 — Core logic supply |
| Pin produk 3 | VSS1 — Ground reference |
| Pin produk 4 | VDD2 — I/O supply |
| Pin produk 5 | VSS2 — Ground reference |
| Pin produk 6 | RESET — External reset input (active low) |
| Pin produk 7 | MODC — Mode select for BDM/normal |
| Pin produk 8 | PAD0 — Port AD bit 0 / AN0 |
| Pin produk 9 | PAD1 — Port AD bit 1 / AN1 |
| Pin produk 10 | PAD2 — Port AD bit 2 / AN2 |
| Pin produk 11 | PAD3 — Port AD bit 3 / AN3 |
| Pin produk 12 | PAD4 — Port AD bit 4 / AN4 |
| Pin produk 13 | PAD5 — Port AD bit 5 / AN5 |
| Pin produk 14 | PAD6 — Port AD bit 6 / AN6 |
| Pin produk 15 | PAD7 — Port AD bit 7 / AN7 |
| Pin produk 16 | PAD8 — Port AD bit 8 / AN8 |
| Pin produk 17 | PAD9 — Port AD bit 9 / AN9 |
| Pin produk 18 | PAD10 — Port AD bit 10 / AN10 |
| Pin produk 19 | PAD11 — Port AD bit 11 / AN11 |
| Pin produk 20 | PAD12 — Port AD bit 12 / AN12 |
| Pin produk 21 | PAD13 — Port AD bit 13 / AN13 |
| Pin produk 22 | PAD14 — Port AD bit 14 / AN14 |
| Pin produk 23 | PAD15 — Port AD bit 15 / AN15 |
| Pin produk 24 | PAD16 — Port AD bit 16 / AN16 |
| Pin produk 25 | PAD17 — Port AD bit 17 / AN17 |
| Pin produk 26 | PAD18 — Port AD bit 18 / AN18 |
| Pin produk 27 | PAD19 — Port AD bit 19 / AN19 |
| Pin produk 28 | PAD20 — Port AD bit 20 / AN20 |
| Pin produk 29 | PAD21 — Port AD bit 21 / AN21 |
| Pin produk 30 | PAD22 — Port AD bit 22 / AN22 |
| Pin produk 31 | PAD23 — Port AD bit 23 / AN23 |
| Pin produk 32 | VDD3 — I/O supply |
| Pin produk 33 | VSS3 — Ground reference |
| Pin produk 34 | PA0 — Port A bit 0 |
| Pin produk 35 | PA1 — Port A bit 1 |
| Pin produk 36 | PA2 — Port A bit 2 |
| Pin produk 37 | PA3 — Port A bit 3 |
| Pin produk 38 | PA4 — Port A bit 4 |
| Pin produk 39 | PA5 — Port A bit 5 |
| Pin produk 40 | PA6 — Port A bit 6 |
| Pin produk 41 | PA7 — Port A bit 7 |
| Pin produk 42 | PB0 — Port B bit 0 |
| Pin produk 43 | PB1 — Port B bit 1 |
| Pin produk 44 | PB2 — Port B bit 2 |
| Pin produk 45 | PB3 — Port B bit 3 |
| Pin produk 46 | PB4 — Port B bit 4 |
| Pin produk 47 | PB5 — Port B bit 5 |
| Pin produk 48 | PB6 — Port B bit 6 |
| Pin produk 49 | PB7 — Port B bit 7 |
| Pin produk 50 | PC0 — Port C bit 0 |
| Pin produk 51 | PC1 — Port C bit 1 |
| Pin produk 52 | PC2 — Port C bit 2 |
| Pin produk 53 | PC3 — Port C bit 3 |
| Pin produk 54 | PC4 — Port C bit 4 |
| Pin produk 55 | PC5 — Port C bit 5 |
| Pin produk 56 | PC6 — Port C bit 6 |
| Pin produk 57 | PC7 — Port C bit 7 |
| Pin produk 58 | PE0 — Port E bit 0 / XIRQ |
| Pin produk 59 | PE1 — Port E bit 1 / IRQ |
| Pin produk 60 | PE2 — Port E bit 2 |
| Pin produk 61 | PE3 — Port E bit 3 |
| Pin produk 62 | PE4 — Port E bit 4 |
| Pin produk 63 | PE5 — Port E bit 5 |
| Pin produk 64 | PE6 — Port E bit 6 |
| Pin produk 65 | PE7 — Port E bit 7 |
| Pin produk 66 | PF0 — Port F bit 0 |
| Pin produk 67 | PF1 — Port F bit 1 |
| Pin produk 68 | PF2 — Port F bit 2 |
| Pin produk 69 | PF3 — Port F bit 3 |
| Pin produk 70 | PF4 — Port F bit 4 |
| Pin produk 71 | PF5 — Port F bit 5 |
| Pin produk 72 | PF6 — Port F bit 6 |
| Pin produk 73 | PF7 — Port F bit 7 |
| Pin produk 74 | PG0 — Port G bit 0 |
| Pin produk 75 | PG1 — Port G bit 1 |
| Pin produk 76 | PG2 — Port G bit 2 |
| Pin produk 77 | PG3 — Port G bit 3 |
| Pin produk 78 | PG4 — Port G bit 4 |
| Pin produk 79 | PG5 — Port G bit 5 |
| Pin produk 80 | PG6 — Port G bit 6 |
| Pin produk 81 | PG7 — Port G bit 7 |
| Pin produk 82 | PH0 — Port H bit 0 |
| Pin produk 83 | PH1 — Port H bit 1 |
| Pin produk 84 | PH2 — Port H bit 2 |
| Pin produk 85 | PH3 — Port H bit 3 |
| Pin produk 86 | PH4 — Port H bit 4 |
| Pin produk 87 | PH5 — Port H bit 5 |
| Pin produk 88 | PH6 — Port H bit 6 |
| Pin produk 89 | PH7 — Port H bit 7 |
| Pin produk 90 | PJ0 — Port J bit 0 |
| Pin produk 91 | PJ1 — Port J bit 1 |
| Pin produk 92 | PJ2 — Port J bit 2 |
| Pin produk 93 | PJ3 — Port J bit 3 |
| Pin produk 94 | PJ4 — Port J bit 4 |
| Pin produk 95 | PJ5 — Port J bit 5 |
| Pin produk 96 | PJ6 — Port J bit 6 |
| Pin produk 97 | PJ7 — Port J bit 7 |
| Pin produk 98 | BKGD — Background Debug Mode interface |
| Pin produk 99 | TCLK — Timer clock input |
| Pin produk 100 | XCLKS — Crystal oscillator mode select |
| Pin produk 101 | XTAL — Crystal oscillator output |
| Pin produk 102 | EXTAL — Crystal oscillator input |
| Pin produk 103 | VDDPLL — PLL supply |
| Pin produk 104 | VSSPLL — PLL ground |
| Pin produk 105 | VDD4 — I/O supply |
| Pin produk 106 | VSS4 — Ground reference |
| Pin produk 107 | CAN0TX — CAN0 transmit |
| Pin produk 108 | CAN0RX — CAN0 receive |
| Pin produk 109 | CAN1TX — CAN1 transmit |
| Pin produk 110 | CAN1RX — CAN1 receive |
| Pin produk 111 | NC — Not connected (per datasheet) |
| Pin produk 112 | VSS5 — Ground reference |
Aplikasi Umum
S912XEQ384J3CAL cocok untuk 6 aplikasis: Automotive Body Control Module, Instrument Cluster Peripherals, Industrial PLC Node Controller, HVAC Climate Control Module, Battery Management Slave Module, Motor Control Peripheral Board.
Automotive Body Control Module
The S912XEQ384J3CAL fits automotive body control modules because its 384 KB flash accommodates multi-feature BCM firmware while the XGATE co-processor offloads CAN/LIN message buffering at high event rates. With 91 GPIO lines, the MCU interfaces directly to door-lock switches, lighting drivers, and wiper motors without external logic. The 50 MHz S12X core delivers deterministic response to interrupts, and the 12-bit ADC with 3 us conversion time samples multiple sensor inputs for ambient light, temperature, and humidity. Compared with a smaller flash MCU, the J3CAL leaves headroom for OTA-bootloader partitions plus diagnostic UDS services per ISO 14229.
Direkomendasikan
Instrument Cluster Peripherals
The S912XEQ384J3CAL is well-matched to instrument cluster peripheral controllers because its Enhanced Capture Timer (ECT) provides precise pulse measurement for wheel-speed and engine-RPM sensing. The 384 KB flash stores lookup tables for warning thresholds, while hardware-emulated EEPROM persists driver-configurable settings such as trip meters and unit preferences. Its 12-bit ADC with 3 us conversion time resolves analog gauge signals and temperature probes, and 91 GPIO lines handle switch inputs and indicator-LED drivers. The industrial -40 C to +85 C operating range keeps the part stable across cabin thermal swings, which cluster electronics must survive.
Direkomendasikan
Industrial PLC Node Controller
The S912XEQ384J3CAL suits industrial PLC node controllers because the S12X core's deterministic interrupt latency and the XGATE co-processor handle deterministic I/O scanning without jitter. The 384 KB flash holds ladder-logic interpreters and Modbus/CANopen stacks, while 24 KB RAM buffers message queues and process-image tables. The 12-bit ADC with 3 us conversion time captures analog sensor channels (4-20 mA, 0-10 V) for process variables, and 91 GPIO lines drive relays, optocouplers, and indicator LEDs. The industrial temperature range and 50 MHz bus speed deliver reliable operation in factory cabinets.
Direkomendasikan
HVAC Climate Control Module
The S912XEQ384J3CAL suits HVAC climate-control modules because its 12-bit ADC with 3 us conversion time reads cabin and duct temperature sensors, and its Enhanced Capture Timer precisely schedules PWM outputs for blower-motor and blend-door actuators. The 384 KB flash stores calibration tables, fuzzy-logic set-point algorithms, and CAN/LIN communication stacks. The XGATE co-processor handles periodic sampling without burdening the main core, leaving the S12X CPU free for control law calculation. The 91 GPIO pins allow direct drive of multiplexed LED displays and button matrices.
Direkomendasikan
Battery Management Slave Module
The S912XEQ384J3CAL fits BMS slave modules because its 12-bit ADC with 3 us conversion time samples individual cell voltages in a battery stack, and its 91 GPIO support cell-balancing FET control via daisy-chained peripherals. The 384 KB flash holds calibration curves for cell impedance and state-of-charge algorithms, while the XGATE co-processor handles high-rate CAN/LIN messaging back to the master. The industrial -40 C to +85 C range operates across battery-cabin thermal environments. Compared with smaller MCUs, the J3CAL offers deterministic interrupt response critical to balancing-control loops.
Direkomendasikan
Motor Control Peripheral Board
The S912XEQ384J3CAL is appropriate for motor-control peripheral boards because its Enhanced Capture Timer provides the resolution needed for Hall-sensor decoding and PWM generation, and its 50 MHz S12X core runs field-oriented control loops with the XGATE co-processor managing ADC-triggered sampling. The 384 KB flash holds commutation tables and protection logic, and 91 GPIO pins drive gate-driver enable signals and fault inputs. Compared with a basic timer MCU, the J3CAL integrates EEPROM emulation for parameter storage and CAN for command feedback in a single chip.
Direkomendasikan
Ringkasan Produk Direkomendasikan
Data referensi engineering untuk S912XEQ384J3CAL — pembandingan, panduan desain, dan informasi konformitas.
Panduan Pemilihan
Pembandingan dengan Alternatif
| Parameter Umum | Produk Ini | MC9S12XEQ384CAG | S912XEG384J2VAL | S912XET512BMAGR | S912XET512J2VAGR | S912XET256J2VAG | S9S12XF384J2MLMR |
|---|---|---|---|---|---|---|---|
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Package | 112-LQFP (20x20 mm) | 112-LQFP (20x20 mm) - same | 112-LQFP (20x20 mm) - same | 112-LQFP (20x20 mm) - same | 112-LQFP (20x20 mm) - same | 112-LQFP (20x20 mm) - same | 112-LQFP (20x20 mm) - same |
| Core | S12X 16-bit | S12X 16-bit | S12X 16-bit | S12X 16-bit | S12X 16-bit | S12X 16-bit | S12X 16-bit |
| Bus Speed | 50 MHz | 50 MHz | 50 MHz | 64 MHz | 50 MHz | 50 MHz | 50 MHz |
| Flash | 384 KB | 384 KB | 384 KB | 512 KB | 512 KB | 256 KB | 384 KB |
| RAM | 24 KB | 24 KB | 24 KB | 32 KB | 32 KB | 16 KB | 24 KB |
| XGATE Co-processor | Yes | Yes | Yes | Yes | Yes | Yes | Yes |
| GPIO Count | 91 | 91 | 91 | 91 | 91 | 91 | 91 |
| Temperature Range | -40 C to +85 C (industrial) | -40 C to +85 C (industrial) | -40 C to +105 C (automotive) | -40 C to +85 C (industrial) | -40 C to +105 C (automotive) | -40 C to +105 C (automotive) | -40 C to +85 C (industrial) |
Diferensiator Kunci
- Largest flash in the J3CAL mask set with XGATE offload engine (vsS912XET256J2VAG)
- Industrial temperature grade matched to cabinet-mounted applications (vsS912XEG384J2VAL)
- Identical silicon and peripherals under the legacy Freescale prefix (vsMC9S12XEQ384CAG)
- 50 MHz deterministic interrupt response with hardware-envelope EEPROM (vsS912XET512BMAGR)
Catatan Desain
The S912XEQ384J3CAL has separate VDD1/VDD2/VDD3/VDD4 supply domains plus VDDPLL; decouple each pair with a 100 nF ceramic capacitor placed within 5 mm of the pin, plus a bulk 4.7 uF tantalum or ceramic on the regulator output. Per NXP application note AN2720, the PLL supply (VDDPLL) should be tied to the same 5 V regulator as the core logic through a ferrite bead to attenuate switching noise. Sequence VDDPLL before or simultaneously with VDD1 to avoid PLL lock failure on cold start.
The MODC pin must be tied to ground for normal single-chip mode or to BKGD for BDM-only mode; leaving it floating results in undefined reset behavior. Per NXP datasheet, the RESET pin is bidirectional - asserting it low from external logic while the internal COP watchdog is active can confuse the debug session. Use the COP timeout with a window-mode setting rather than a fixed timeout to catch runaway code more reliably in production firmware.
Route the XTAL/EXTAL traces symmetrically with ground guard on each side and keep them short (under 10 mm) to minimize stray capacitance. Per NXP S12XE hardware design notes, place the load capacitors (typically 12-33 pF) within 3 mm of the crystal pins. Keep high-speed switching signals (PWM, CAN) at least 30 mm from the crystal area to avoid frequency jitter. Use a continuous ground plane under the IC and stitch vias around the 112-LQFP perimeter to reduce thermal impedance and EMI.
Informasi Konformitas
Industrial temperature grade (-40 C to +85 C) per NXP datasheet; not AEC-Q100 qualified - choose J2VAL or other AEC-Q100 variants for automotive safety-critical modules. RoHS compliant per NXP product page.
