SN74LS465N - Octal 3-State Buffer | Texas Instruments
MPN: SN74LS465N ✓ AktifSN74LS465N Ringkasan
A logic buffer is a digital IC that reproduces an input signal at an output while providing buffering and load-drive capability. In the digital-component hierarchy, this octal buffer belongs to the Logic ICs family and can be described as a bus buffer, non-inverting buffer, three-state logic buffer, and TTL-compatible interface element. The 3-state outputs can represent logic high, logic low, or a high-impedance condition, allowing multiple devices to share a communication line when only one output is actively enabled at a time.
The principal feature of the SN74LS465N is its combination of eight non-inverting channels and independently controlled 3-state outputs. This architecture is appropriate for bus buffering, signal isolation during multiplexing, and protecting a logic source from the electrical loading of a destination bus. The octal organization allows eight signals to be buffered in parallel rather than requiring multiple single-channel devices. Its 20-pin PDIP package also supports conventional through-hole assembly, prototyping, repair, and legacy industrial equipment.
The SN74LS465N differs from a basic eight-channel buffer by providing a controlled high-impedance output state. That state is valuable when multiple drivers connect to one shared conductor: inactive outputs can be released instead of driving a conflicting level. The non-inverting configuration preserves logical polarity, so a low input produces a low output and a high input produces a high output while the output is enabled. Designers should still account for input and output logic levels, enable timing, fanout, and total bus loading when integrating the device into a larger system.
Typical applications include buffered bus expansion, bidirectional data-path isolation where the external interface direction is controlled elsewhere, address or control-line buffering, and retrofitting older TTL systems that require three-state capability. It can also support laboratory and industrial test equipment where several instruments or circuit modules need to share a wired logic line. Because the SN74LS465N is a through-hole legacy-style device, it is particularly practical for maintaining equipment assembled with DIP components rather than compact surface-mount designs.
The primary design consideration is output-enable control. Keep all enable inputs in a defined state during reset so no output unintentionally enters the high-impedance condition. Route enable traces away from noisy switching nodes, maintain compatible logic thresholds across the complete system, and avoid exceeding the electrical limits stated in the Texas Instruments manufacturer datasheet. The DIP footprint also requires adequate spacing for insertion, soldering, inspection, and component replacement.
This product page combines the exact device identity and package information with practical buffer-selection guidance, verified sourcing links, and a focused comparison of possible replacement devices. It is intended to help engineers identify the function, verify the 20-pin footprint, review replacement constraints, and plan assembly or repair work without overlooking three-state bus behavior.
Alternatif penggantian untuk SN74LS465N — paket yang sama, pin-pada-pin kompatibel. Bagian paket yang berbeda memerlukan kerja ulang PCB diabaikan.
SN74LS465A
✅ Drop-In ⚠️ Spesifikasi Tidak Disahkan📋 Alternatif referensi (tidak dalam katalog)
DM74LS465N
✅ Drop-In📋 Alternatif referensi (tidak dalam katalog)
MC74LS465N
✅ Drop-In📋 Alternatif referensi (tidak dalam katalog)
NTE74LS465N
✅ Drop-In📋 Alternatif referensi (tidak dalam katalog)
74LS465N
✅ Drop-In📋 Alternatif referensi (tidak dalam katalog)
SN74LS465N Rating Maksimal & Karakteristik Listrik
| Logic Type | Octal non-inverting buffer |
| Konfigurasi Output | 3-state |
| Number of Elements | 1 element |
| Bits per Element | 8 bits |
| Number of Channels | 8 channels |
| Output Polarity | Non-inverting |
| Package Type | 20-PDIP |
| Total Pin Count | 20 pins |
| Tipe Mounting | Through-hole |
SN74LS465N 20-pdip Diamant Konfigurasi Panduan
Konfigurasi pin untuk SN74LS465N (20-pdip pakai pakai). IC digital ini termasuk GPIO, antarmuka komunikasi (UART, SPI, I2C), dan pin kuasa. Lihat datasheet produsen untuk fungsi pin alternatif dan opsi konfigurasi. Penting untuk desain sistem pengemasan dan PCB.
Tidak ada data diatribut pin yang tersedia untuk SN74LS465N.
Lihat ke: datasheet produk untuk konfigurasi pin penuh.
Aplikasi Umum
SN74LS465N cocok untuk 6 aplikasis: Shared Digital Bus Isolation, Legacy TTL Bus Expansion, Address and Control-Line Buffering, Industrial Test Equipment Interconnect, Instrument Signal Multiplexing, Vintage Equipment Repair.
Shared Digital Bus Isolation
The SN74LS465N fits shared-bus isolation because it provides eight non-inverting channels with 3-state outputs in one 20-pin PDIP device. Place the buffer between a source logic section and a bus that may be driven by more than one module, then use enable control to release inactive outputs. The high-impedance state prevents multiple drivers from actively fighting over the same line, while the eight parallel channels simplify control of an entire byte or group of bus signals. Confirm output-enable polarity and timing from the Texas Instruments manufacturer datasheet before defining the enable logic.
Direkomendasikan
Legacy TTL Bus Expansion
The SN74LS465N is useful when an older TTL design needs additional non-inverting bus drive without changing to a surface-mount logic family. Its eight buffered channels can carry a complete parallel data group, and the 20-pin PDIP package is convenient for conventional through-hole PCB layouts, prototype boards, and repair assemblies. Buffering can reduce loading seen by the upstream device and isolate it from downstream capacitance. Check the original system voltage, fanout requirements, and propagation-delay budget before inserting the SN74LS465N into the signal path.
Direkomendasikan
Address and Control-Line Buffering
The SN74LS465N can buffer address, chip-select, reset, or other control lines when a legacy system presents too much load to one driver. Its non-inverting 3-state channels preserve control polarity, and the octal arrangement allows several controls to be buffered consistently in a single package. For multiplexed interfaces, enable the buffer only while it owns the destination lines and return it to high impedance when another subsystem is selected. Verify that setup and hold timing remain adequate at the system clock frequency.
Direkomendasikan
Industrial Test Equipment Interconnect
The SN74LS465N is appropriate for industrial test and measurement equipment that uses wired TTL logic levels and needs controlled bus ownership. Its eight non-inverting, three-state outputs allow a central controller to interface with one external module at a time while keeping other modules electrically released. The 20-pin PDIP construction is especially practical for older instrumentation, control panels, and field-maintenance boards. Add input protection and grounding appropriate to the installation, and confirm that the device's specified environmental ratings cover the intended operating conditions.
Direkomendasikan
Instrument Signal Multiplexing
The SN74LS465N can support a wired multiplexer in laboratory equipment where several digital sources must connect to a common destination. Eight parallel channels provide non-inverting buffering, while 3-state outputs allow the selected source to drive and the inactive sources to remain high impedance. This arrangement helps prevent bus contention and maintains compatible logic levels through the interconnect. The design must define enable priority during startup and reset so that two channels are never enabled simultaneously when they could drive conflicting levels.
Direkomendasikan
Vintage Equipment Repair
The SN74LS465N is well suited to repairing older TTL-based equipment because it retains a 20-pin PDIP footprint and provides the same octal three-state-buffer function used in legacy bus interfaces. Technicians can replace a failed device without introducing a new surface-mount footprint or changing the board architecture. Before installation, verify pin orientation, output-enable polarity, supply voltage, and any socketed-module compatibility. After replacement, test that no multiple outputs are enabled at the same time and that the repaired bus meets the original timing requirements.
Direkomendasikan
Ringkasan Produk Direkomendasikan
Data referensi engineering untuk SN74LS465N — pembandingan, panduan desain, dan informasi konformitas.
Panduan Pemilihan
Pembandingan dengan Alternatif
| Parameter Umum | Produk Ini | SN74LS465A | DM74LS465N | MC74LS465N | NTE74LS465N | 74LS465N |
|---|---|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Fairchild Semiconductor | Motorola | NTE Semiconductors | Signetics |
| Package | 20-PDIP | 20-PDIP - same | 20-PDIP - same | 20-PDIP - same | 20-PDIP - same | 20-PDIP - same |
| Number of Channels | 8 channels | 8 channels | 8 channels | 8 channels | 8 channels | 8 channels |
| Output State | 3-state | 3-state | 3-state | 3-state | 3-state | 3-state |
| Output Polarity | Non-inverting | Non-inverting | Non-inverting | Non-inverting | Non-inverting | Non-inverting |
Diferensiator Kunci
- Eight non-inverting channels combined with three-state outputs (vsSN74LS245N)
- Confirmed 20-pin PDIP construction (vsSN74LS245NSR)
- Suitable for conventional through-hole maintenance (vsSN74LVCH244ARGYR)
Catatan Desain
Do not enable two SN74LS465N buffers that are connected to the same bus conductor. Although each output can provide a high-impedance state, simultaneous active-high or active-low enable commands can place two drivers in conflict. Define a single ownership policy, force all enable inputs into a safe state during reset, and test the sequencing with worst-case power-up conditions.
Use the manufacturer timing and load characteristics to determine whether the buffered channel can support the connected bus capacitance and switching frequency. Place the device close enough to the driven interface to minimize trace inductance and ringing, but preserve the output-enable routing required for clean bus ownership. Avoid long unprotected branches from shared outputs because they increase capacitive loading and reflection risk.
The SN74LS465N uses a 20-pin PDIP footprint, so confirm socket compatibility, row spacing, hole size, and keep-out requirements before layout approval. Maintain pin-1 orientation against the PCB silkscreen and socket marking. For repair-focused designs, a socket can simplify replacement, but its additional pin and contact capacitance should be checked against timing and loading requirements.
Informasi Konformitas
No specific RoHS, REACH, lead-free, halogen-free, or conflict-minerals statement was identified for the exact device. AEC-Q100 is not applicable to this general-purpose logic IC based on the confirmed device category.