Texas Instruments

THS4131CDR - 225 MHz Fully Differential Amplifier | TI

MPN: THS4131CDR ✓ Aktif
4 V to 33 V Vdss 8-pin SOIC (D) Package
MOQ: 1 |

THS4131CDR Ringkasan

The Texas Instruments THS4131CDR is a fully differential input/output low-noise amplifier with 225 MHz bandwidth, a 4 V to 33 V total supply-voltage range, and an 8-pin SOIC package. It uses a true fully differential signal path to support balanced signal chains and provides a single differential output suitable for high-speed ADC drivers, line receivers, and instrumentation.

A fully differential amplifier is an amplifier category that processes a pair of complementary or differential signals rather than a single-ended voltage. Its place in the signal-chain hierarchy is analog amplification: it receives a balanced input, amplifies the differential component, and rejects common-mode noise and offset. This architecture helps preserve signal integrity when a system uses differential ADC inputs, balanced communications links, or precision measurement front ends.

The THS4131CDR combines 225 MHz bandwidth with low-noise operation, making it useful where accurate amplification must occur at high signal rates. Its differential output reduces the need for a separate output-balancing stage when the next circuit accepts a differential input. The wide 4 V to 33 V total supply range also allows operation from low-voltage analog systems as well as higher-voltage instrumentation rails, subject to the complete operating conditions in the manufacturer datasheet.

Texas Instruments fabricates this device using its high-voltage complementary bipolar process. The BiComI process supports the high-speed operation and low-noise characteristics required by demanding analog interfaces. A fully differential signal path from input to output also provides improved common-mode rejection compared with a conventional single-ended amplifier followed by a discrete subtractor.

Typical uses include driving high-speed analog-to-digital converters, receiving balanced communications signals, amplifying low-level sensor outputs, and conditioning signals in laboratory and industrial instrumentation. Differential output can simplify board routing because the two output conductors can be treated as one balanced pair, reducing sensitivity to ground-bounce and shared-impedance disturbances.

Layout is as important as bandwidth in a 225 MHz design. Keep the feedback components and signal traces short, use a solid ground plane, and place decoupling capacitors close to the supply pins. Follow the recommended component values and evaluation-board layout in the manufacturer datasheet rather than substituting large capacitors or long traces without impedance verification.

This page combines the THS4131 family electrical information, package details, sourcing references, and engineering design guidance. It also distinguishes exact pin-compatible alternatives from merely similar amplifier functions, helping designers avoid replacements that require a board or interface change.

Alternatif penggantian untuk THS4131CDR — paket yang sama, pin-pada-pin kompatibel. Bagian paket yang berbeda memerlukan kerja ulang PCB diabaikan.

Variasi di dalam seri ini

Model-series yang sama yang kompatibel dengan penggantian THS4131CDR (sama faktor bentuk dan footprint) — berbeda di dalam Gain-Bandwidth Product, Product Type.

Texas Instruments
Gain-Bandwidth Product: 210 MHz
Product Type: Single high-speed FET-input operational amplifier
Bandingkan dengan THS4131CDR →

Tidak ada alternatif pengganti yang tersedia untuk produk ini.

Permintaan Alternatif

THS4131CDR Rating Maksimal & Karakteristik Listrik

Product Type Fully differential input/output low-noise amplifier
Amplifier Type Fully differential amplifier
Channel Count 1 channel
Gain-Bandwidth Product 225 MHz
Total Supply Voltage Range 4 V to 33 V
Single-Supply Operation 5 V typical
Dual-Supply Operation ±5 V to ±16.5 V
Rentang Suhu Kerja 0 °C to 70 °C
Package Type 8-pin SOIC (D)
Tipe Mounting Surface mount
Process Technology High-voltage complementary bipolar (BiComI)

THS4131CDR 8-pin soic (d) Diamant Konfigurasi Panduan

Konfigurasi pin untuk THS4131CDR (8-pin soic (d) pakai pakai). Komponen analog ini memiliki pin masukan, keluaran, dan pengirim daya. Lihat datasheet produsen untuk konfigurasi pin offset null, kompensasi, dan pengaktifan. Ideal untuk peralatan sinyal dan kabel penggandaran.

Diamant diagram pakai pakai 8-pin soic (d) untuk THS4131CDR

Tidak ada data diatribut pin yang tersedia untuk THS4131CDR.

Lihat ke: datasheet produk untuk konfigurasi pin penuh.

Aplikasi Umum

THS4131CDR cocok untuk 6 aplikasis: High-Speed Differential ADC Driver, Balanced Communications Receiver, Precision Instrumentation Front End, Laboratory Signal Conditioning, Data Acquisition Front End, Audio and Low-Level Signal Amplification.

📈

High-Speed Differential ADC Driver

The THS4131CDR suits ADC front ends that accept a complementary differential input, with its 225 MHz bandwidth providing useful headroom for high-rate conversion stages. The fully differential output avoids a separate balance-output amplifier and allows the converter input, device output, and return path to be routed as a controlled pair. Confirm ADC input capacitance, allowable gain, settling time, and common-mode limits against the exact converter requirements. Keep the amplifier feedback elements and output traces short, because long routes can add parasitic capacitance and reduce stability margin.

🌐

Balanced Communications Receiver

A differential receiver can use the THS4131CDR to recover a small differential signal while rejecting common-mode disturbances picked up along a cable or board interface. Its 225 MHz bandwidth covers high-speed baseband channels, and the true differential input path is preferable to emulating balance with two separate amplifiers. Source termination, input impedance, and the receiver protocol determine the actual usable bandwidth. Use symmetrical routing and a continuous ground reference, then verify the design with time-domain and eye measurements before release.

🏭

Precision Instrumentation Front End

The THS4131CDR can condition low-level differential sensor outputs where signal integrity and common-mode rejection are more important than single-ended simplicity. Its low-noise fully differential architecture keeps the input stage and output balanced from the source through the next conversion or filtering stage. Instrumentation applications often involve long cables or ground-potential differences, so the source impedance and protection network must be designed carefully. Confirm noise density, input bias current, and common-mode behavior in the manufacturer datasheet before selecting the external gain network.

🔧

Laboratory Signal Conditioning

Bench instruments often combine a small differential source with a wideband converter or measurement front end. The THS4131CDR provides 225 MHz bandwidth and a differential output in an 8-pin SOIC package, allowing it to serve as the interface between balanced source circuitry and downstream test channels. Component tolerances and parasitic capacitance in the feedback network directly influence gain accuracy and settling behavior. Use the manufacturer evaluation layout as a starting point, especially when the source impedance is high or the required settling interval is short.

🖥️

Data Acquisition Front End

In multi-channel data-acquisition systems, the THS4131CDR can preserve a balanced path from a differential source toward an ADC, reducing the need for separate input and subtraction stages. The 225 MHz bandwidth supports many high-speed acquisition rates, although the converter interface usually determines the practical limit. Check the ADC sampling architecture, input settling requirements, and pin-compatible power plan together. Differential routing also reduces susceptibility to shared ground impedance, provided both signal conductors have matched geometry and a continuous return path.

🎧

Audio and Low-Level Signal Amplification

The low-noise fully differential architecture of the THS4131CDR can serve balanced audio or low-level sensor interfaces where preserving the differential signal is important. Its 225 MHz bandwidth is substantially higher than the audible range, providing margin for filtering and system architecture rather than serving as a stated audio-bandwidth limit. The differential output can feed balanced downstream circuitry without a separate subtractor. Verify the actual noise-density requirement and common-mode range at the operating gain, since bandwidth alone does not establish signal-to-noise performance.

Ringkasan Produk Direkomendasikan

THS4062IDR Texas Instruments Digunakan di dalam: High-Speed Differential ADC Driver, Balanced Communications Receiver, Precision Instrumentation Front End, Laboratory Signal Conditioning, Data Acquisition Front End, Audio and Low-Level Signal Amplification THS4131CD Same-device family alternative in an 8-pin SOIC configuration Digunakan di dalam: High-Speed Differential ADC Driver, Balanced Communications Receiver, Precision Instrumentation Front End, Laboratory Signal Conditioning, Data Acquisition Front End, Audio and Low-Level Signal Amplification
What is the bandwidth of the THS4131CDR?
The THS4131CDR provides 225 MHz gain-bandwidth performance. According to the Texas Instruments THS4131 family datasheet, the device uses a true fully differential input-to-output signal path designed for low-noise, high-speed signal conditioning. This bandwidth makes it suitable for high-speed ADC interfacing, balanced communications receivers, and instrumentation where the signal must be amplified without severe bandwidth limitations.
What type of amplifier is the THS4131CDR?
The THS4131CDR is a one-channel fully differential input/output low-noise amplifier in an 8-pin SOIC package. Its architecture accepts differential signals and provides a differential output, reducing the need for a separate subtractor. Texas Instruments describes the THS413x family as high-speed, low-noise amplifiers fabricated with a high-voltage complementary bipolar process.
What is the supply voltage range of THS4131CDR?
The THS4131CDR operates across a 4 V to 33 V total supply-voltage range. The comparison data for this exact device identifies 4 V as the minimum and 33 V as the maximum total supply voltage. Operation near either limit requires checking the input common-mode range, output swing, and power dissipation against the conditions in the manufacturer datasheet.
Where can I download the THS4131CDR datasheet PDF?
The official THS4131 datasheet PDF is available from Texas Instruments at https://www.ti.com/lit/ds/symlink/ths4131.pdf. It covers the THS4130 and THS4131 family, including electrical characteristics, pin configuration, typical performance curves, and application information. Use the THS4131-specific sections and ordering information when working with the THS4131CDR part number.
Where can I find the THS4131CDR pinout?
The THS4131CDR pin configuration is shown in the Pin Configuration section of the official Texas Instruments THS4131 family datasheet. The device is an 8-pin SOIC with differential inputs and a differential output. Assign PCB nets using the numbered diagram rather than relying on package-side marking or board-layout assumptions.
Can the THS4131CDR drive a high-speed ADC?
Yes, the THS4131CDR is suitable for many high-speed ADC input stages because it combines a 225 MHz bandwidth with a fully differential output. Differential output can feed complementary ADC inputs while reducing sensitivity to common-mode noise. Confirm ADC input capacitance, settling requirements, gain, and supply level against the complete ADC interface specification before finalizing the circuit.
Is the THS4131CDR a single-ended or differential amplifier?
The THS4131CDR is fully differential at both the input and output, rather than a single-ended amplifier requiring an external subtractor. Its true differential signal path improves common-mode rejection and supports balanced routing throughout the analog chain. This makes it a closer functional match to differential ADC front ends than a conventional single-ended operational amplifier.
What are the key specifications of THS4131CDR?
The principal THS4131CDR specifications are 225 MHz bandwidth, a 4 V to 33 V total supply range, one fully differential input/output channel, an 8-pin SOIC package, and a 0 °C to 70 °C commercial temperature range. Texas Instruments also identifies the device as a low-noise amplifier produced with a high-voltage complementary bipolar process.
What can replace the THS4131CDR?
The closest exact replacement is the electrically identical THS4131 in the same 8-pin SOIC footprint, subject to package-ordering and availability differences. A valid drop-in replacement must preserve the differential input/output architecture, pin assignment, bandwidth class, and supply compatibility. Amplifiers with only similar bandwidth or the same package count are not drop-in substitutes.
Is the THS4131CD the same as the THS4131CDR?
The THS4131CD and THS4131CDR belong to the same THS4131 device family and use the same 8-pin SOIC electrical configuration, but their orderable suffix codes identify different shipment formats. Whether the non-reel version can replace the reel version depends on assembly handling rather than circuit compatibility. Verify the required delivery format before treating them as interchangeable in a purchasing or assembly plan.
Can the THS4631D replace the THS4131CDR?
The THS4631D is not a verified pin-to-pin replacement for the THS4131CDR. Both are listed in 8-pin SOIC packages, but the THS4631D is described as a high-speed FET-input operational amplifier while the THS4131CDR is a fully differential input/output amplifier. Matching package size alone does not establish compatible pin functions, biasing, or signal-path behavior.
Can the THS4062CD replace the THS4131CDR?
The THS4062CD is not a direct drop-in replacement for the THS4131CDR. The THS4062 family provides dual low-noise op amps for precision instrumentation, whereas the THS4131CDR is a single fully differential input/output amplifier. Although both can appear in SOIC-8 packages, the internal functions and pin assignments differ, so a PCB substitution requires redesign rather than component exchange.
When should I choose a fully differential amplifier instead of a single-ended op amp?
Choose a fully differential amplifier when the signal source, routing environment, and destination are balanced. The THS4131CDR supports a complete differential path, which can improve common-mode rejection and simplify balanced ADC connections. A single-ended amplifier such as a THS4062 device may be preferable when the source is genuinely single-ended and no downstream differential interface exists.
Is THS4131CDR suitable for balanced communications receivers?
The THS4131CDR is suitable for many balanced receiver front ends because its 225 MHz bandwidth and fully differential input path support high-speed data amplification. The output remains differential, allowing direct coupling to compatible downstream circuitry. Board-level performance still depends on controlled-impedance routing, return-path continuity, and the amplifier stability recommendations in the manufacturer datasheet.
How do I request a quote and current lead time for THS4131CDR?
Use the Request a Quote form on this page to ask about current THS4131CDR pricing, stock, and lead time. The component is offered in an 8-pin SOIC package, and Texas Instruments lists THS4131CDR with a 0 °C to 70 °C temperature range. Confirm the current manufacturing status, authorized-channel availability, and shipment format with the quotation response.

Data referensi engineering untuk THS4131CDR — pembandingan, panduan desain, dan informasi konformitas.

Panduan Pemilihan

Choose the THS4131CDR when the signal source and destination are balanced, the application needs a true differential output, and high-speed operation is required. It is particularly appropriate for high-rate ADC interfaces, balanced communications receivers, and instrumentation where common-mode rejection and a compact 8-pin SOIC implementation matter. Choose a conventional low-noise op amp such as the THS4062 family when the source is single-ended and the downstream circuit does not accept a differential signal. Do not treat the THS4631D as a drop-in choice solely because both devices are available in SOIC-8 packages. No independently verified pin-to-pin alternative with a different manufacturer was identified, so a PCB redesign is safer than assuming that a package-size match guarantees electrical compatibility.

Pembandingan dengan Alternatif

Parameter Umum Produk Ini
Package 8-pin SOIC (D)
Brand Texas Instruments
Amplifier Architecture Fully differential input/output
Channel Count 1 channel
Gain-Bandwidth Product 225 MHz
Total Supply Voltage Range 4 V to 33 V
Operating Temperature Range 0 °C to 70 °C
Output Type Differential
Process Technology High-voltage complementary bipolar (BiComI)

Diferensiator Kunci

  • True fully differential input-to-output signal path (vsTHS4062CD)
  • 225 MHz bandwidth for high-speed conversion interfaces (vsTHS4631D)
  • Wide 4 V to 33 V total supply range (vsTHS4062CD)

Catatan Desain

Treat the differential input and output pairs as controlled-impedance nets. Route the two conductors with matched geometry, maintain a continuous ground reference beneath the pair, and keep the THS4131CDR feedback components close to the device. At 225 MHz, a long feedback loop or an output trace with excessive parasitic capacitance can alter gain, ringing, and stability rather than merely adding a small delay.

Place the supply bypass capacitors immediately adjacent to the supply and ground pins, and follow the component values and placement in the manufacturer evaluation layout. Estimated: with a 10 V total supply and approximately 25 mA quiescent current, static device dissipation is about 0.25 W; actual dissipation rises with output current and the voltage dropped across the amplifier. Confirm the operating point against the datasheet limits before relying on this estimate.

Do not substitute a single-ended amplifier merely because it has a similar bandwidth or an SOIC-8 outline. The THS4131CDR pin functions implement a differential input and differential output, so input termination, common-mode biasing, and feedback connections differ from a conventional operational amplifier. Verify the exact pin-description table and typical application circuit in the manufacturer datasheet before any board substitution is approved.

Informasi Konformitas

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Bebas Logam Lengket
Unknown
Bebas Halogena
Unknown
Mineral Konflik
Unknown

The device is listed by Texas Instruments as a commercial-temperature SOIC part, but explicit RoHS, REACH, halogen-free, and conflict-minerals declarations are not stated in the available product information. AEC-Q100 status is not applicable to this commercial-temperature ordering option.

Data disahkan pada: 2026-11-20 — data disahkan dan disusun oleh tim engineering komponen XAIPART

Pencarian Terkait

THS4131CDR THS4131CDR datasheet THS4131CDR datasheet pdf THS4131CDR pinout THS4131CDR bandwidth THS4131CDR supply voltage THS4131 fully differential amplifier THS4131 SOIC-8 application circuit THS4131CDR equivalent THS4131CDR replacement THS4131CDR vs THS4062CD THS4131CDR price THS4131CDR stock Texas Instruments THS4131CDR

Komponen dan Istilah Terkait

Texas Instruments THS4131CDR THS4131 THS4130 THS4131CD THS4062CD THS4062IDR THS4631D fully differential amplifier differential amplifier low-noise amplifier amplifier IC analog signal chain ADC driver balanced communications receiver common-mode rejection gain-bandwidth product 225 MHz 4 V to 33 V supply voltage BiComI complementary bipolar process 8-pin SOIC SOIC family surface-mount package precision instrumentation
Kutipan Cepat RFQ
Isi detail lengkap — tim penjualan kami akan membalas dalam 24 jam
Nomor Part Manufaktur Paket QTY Harga Target Lengkap
✓
Kutipan telah disubmit!

Kami akan membalas email Anda dalam 24 jam

1
RFQ Dikirim
2
Kutipan Diterima
3
Order Ditempatkan
4
Pembayaran
5
Dikirim
6
Dikirim
Lihat Detil RFQ