Pemberitahuan Beli Terakhir: TJA1041T/H/V mendekati akhir hidup. Tanggal order terakhir: Kontak kami. Lihat bagian alternatif yang tersedia →
NXP Semiconductors

TJA1041T/H/V - 1Mbit/s High-Speed CAN Transceiver | NXP

MPN: TJA1041T/H/V ✗ Akhir Hidup
5 V Vdss 14-pin SOIC Package 1 Mbit/s Speed Optimized for automotive CAN applications Memory
MOQ: 1 |

TJA1041T/H/V Ringkasan

The NXP Semiconductors TJA1041T/H/V is a high-speed CAN bus transceiver supporting data rates up to 1 Mbit/s, operating from a 5 V supply in a 14-pin SOIC package. It provides a differential CANH and CANL bus interface together with transmit and receive paths for connection between a CAN protocol controller and the physical CAN network. The device is designed for automotive high-speed CAN nodes and is compatible with the ISO 11898 standard.

A CAN transceiver is an interface IC that translates logic-level signals from a CAN controller into differential physical-bus signals and converts received differential bus levels back into controller-compatible logic. In the hierarchy of electronic components, the TJA1041T/H/V is a CAN transceiver, which is a bus-interface device within the broader interface IC and semiconductor categories. Its primary role is to isolate the controller from the electrical characteristics, common-mode behavior, and fault conditions found on a wired CAN network.

Key characteristics include operation at up to 1 Mbit/s, ISO 11898 compatibility, a nominal 5 V supply, and an operating temperature range of -40°C to +150°C. NXP describes the TJA1041 as providing excellent electromagnetic compatibility, very low power consumption, and passive behavior when the supply voltage is off. These characteristics make it relevant to automotive body, powertrain, chassis, and industrial CAN systems where bus reliability under temperature and electromagnetic stress is important.

The transceiver uses differential signaling to improve common-mode rejection on the CAN bus. Its transmitter drives the CANH and CANL conductors, while its receiver interprets differential bus voltage. ISO 11898 compatibility provides a defined physical-layer framework for high-speed CAN communication. Because the TJA1041T/H/V does not include a CAN protocol controller, it must be paired with a controller containing CAN TX and RX logic rather than used as a standalone bus node.

Typical applications include automotive electronic control units, body-control modules, powertrain controllers, industrial automation equipment, elevator controls, and embedded CAN gateways. The 1 Mbit/s capability suits conventional CAN systems, while the wide -40°C to +150°C operating range supports harsh industrial and automotive environments. Systems requiring a CAN controller with an integrated transceiver should use a different device family rather than adding this transceiver unnecessarily.

Design attention should be directed to supply decoupling, termination, common-mode choke selection, protection against bus transients, and the separation of sensitive analog or communication paths from noisy power stages. A split termination network can improve EMC behavior, while a common-mode choke can reduce radiated emissions when appropriately selected. PCB placement should minimize loop area around the transceiver and bus-node components because long or poorly controlled high-current loops can increase emissions.

This product reference combines lifecycle information, interface specifications, package details, application guidance, and same-package replacement considerations. It is intended to help engineers distinguish the original TJA1041T/H/V order code from related qualification and packing variants before making a PCB-compatible sourcing decision.

Alternatif penggantian untuk TJA1041T/H/V — paket yang sama, pin-pada-pin kompatibel. Bagian paket yang berbeda memerlukan kerja ulang PCB diabaikan.

TJA1041T/VM,518

✅ Drop-In
📦 SOIC-14
Same 5.25 V and 1 Mbit/s CAN ratings; the /VM qualification and ordering suffix differs from the target /H/V suffix

📋 Alternatif referensi (tidak dalam katalog)

TJA1041T/3

✅ Drop-In ⚠️ Spesifikasi Tidak Disahkan
📦 SOIC-14
Same TJA1041 family, 5 V supply, and 1 Mbit/s interface; the /3 qualification suffix differs from the target /H/V suffix

📋 Alternatif referensi (tidak dalam katalog)

TJA1041T

✅ Drop-In ⚠️ Spesifikasi Tidak Disahkan
📦 SOIC-14
Same TJA1041 5 V, 1 Mbit/s CAN transceiver family in SOIC-14; target adds the /H/V qualification and packing suffix

📋 Alternatif referensi (tidak dalam katalog)

TJA1041T/H/V Spesifikasi

Product Type High-speed CAN transceiver
Maximum CAN Data Rate 1 Mbit/s
Nominal Supply Voltage 5 V
Rentang Suhu Kerja -40°C to +150°C
Paket 14-pin SOIC
Jumlah Pin 14 pins
Tipe Mounting Surface mount
CAN Bus Compatibility ISO 11898
Transmit Interface Differential CANH/CANL
Receive Interface Differential CANH/CANL
Maximum Bus Speed 1 Mbit/s
Off-State Behavior Passive behavior when supply voltage is off
Electromagnetic Compatibility Optimized for automotive CAN applications
Power Consumption Low power consumption
Qualification Code /H/V order-code suffix
Manufacturer Ordering Code TJA1041T/H/V,518

TJA1041T/H/V 14-pin soic Diamant Konfigurasi Panduan

Konfigurasi pin untuk TJA1041T/H/V (14-pin soic pakai pakai). Penomoran pin, fungsi, dan diagram koneksi ditetapkan dalam datasheet produsen. Lihatnya untuk footprint dan pedoman perpindahan paruh.

Diamant diagram pakai pakai 14-pin soic untuk TJA1041T/H/V

Tidak ada data diatribut pin yang tersedia untuk TJA1041T/H/V.

Lihat ke: datasheet produk untuk konfigurasi pin penuh.

Aplikasi Umum

TJA1041T/H/V cocok untuk 6 aplikasis: Automotive Body Control Modules, Powertrain and Chassis Controllers, Industrial Automation Controllers, Building and Elevator Control Systems, Embedded CAN Gateways, Test and Measurement Equipment.

🚗

Automotive Body Control Modules

The TJA1041T/H/V fits an automotive body-control module that connects a CAN protocol controller to the vehicle’s high-speed CAN network. Its 1 Mbit/s capability covers conventional CAN communication, while the -40°C to +150°C operating range addresses the temperature extremes found in vehicle cabins and equipment compartments. The differential CANH/CANL interface improves signal integrity across the bus, and the transceiver’s EMC-focused design is valuable where engine, body, and lighting systems share a common network. Place the device near the bus connector and protection components, provide local 5 V decoupling, and use split termination when needed to improve common-mode performance.

🚗

Powertrain and Chassis Controllers

The TJA1041T/H/V is suitable for powertrain, chassis, and gateway controllers requiring a robust physical interface to a 1 Mbit/s CAN bus. Its extended temperature operation of -40°C to +150°C supports demanding automotive environments, while ISO 11898 compatibility provides a consistent high-speed CAN physical-layer basis. Because the transceiver is exposed to electrically noisy systems, the board should combine it with transient protection, a properly implemented common-mode network, and short return paths. The CAN controller must also verify that its timing and fault-handling behavior are compatible with the transceiver’s bus operating characteristics.

🏭

Industrial Automation Controllers

The TJA1041T/H/V can connect industrial automation controllers to high-speed CAN networks used for machine communication, remote I/O, and production equipment. Its 1 Mbit/s data rate supports factory automation traffic, while the -40°C to +150°C range allows use in equipment exposed to wide environmental variation. The differential bus interface supports reliable communication over longer cable runs when the network is correctly terminated. Designers should still add surge and transient protection at externally accessible connectors and maintain a short separation between the CAN pair to limit radiated emissions and susceptibility to industrial interference.

🏭

Building and Elevator Control Systems

The TJA1041T/H/V is applicable to elevator, access-control, and building-network controllers that use high-speed CAN for distributed equipment communication. The 5 V supply integrates simply with conventional controller logic, and the 1 Mbit/s rate supports control traffic between a central controller and remote nodes. Differential CANH/CANL signaling is useful in buildings where cables may run between separate rooms or equipment cabinets. For reliable deployment, observe proper bus topology and termination, use surge protection at long cable boundaries, and keep the transceiver and its supporting passive network away from high-current switching paths.

🖥️

Embedded CAN Gateways

The TJA1041T/H/V is suitable for an embedded gateway that bridges a host processor or microcontroller to an existing high-speed CAN network. Its 1 Mbit/s capability allows the host to exchange real-time commands and status information with remote nodes. ISO 11898 compatibility supports integration into established CAN systems, while low power consumption and passive off-state behavior are useful in systems where the node may be unpowered during part of its operating cycle. The host CAN controller must be configured for the transceiver’s logic levels and the PCB must follow the manufacturer’s grounding and decoupling guidance.

🔧

Test and Measurement Equipment

The TJA1041T/H/V can be used in CAN bus analyzers, interface modules, and automated test equipment that must connect a computer or controller to a 1 Mbit/s CAN network. Its differential receive and transmit paths provide the physical-layer interface required for monitoring and injecting traffic. The broad temperature range supports laboratory and industrial test environments, while passive off-state behavior helps prevent unintended bus influence during equipment transitions. Use controlled termination and isolated test fixtures where necessary, and avoid leaving an unpowered transceiver connected if the surrounding circuit could inject signals into the bus.

Ringkasan Produk Direkomendasikan

TJA1041T/VM,518 Same-family 14-pin SOIC CAN transceiver Digunakan di dalam: Automotive Body Control Modules, Industrial Automation Controllers, Building and Elevator Control Systems, Test and Measurement Equipment TJA1057GTK/3Z NXP Semiconductors Digunakan di dalam: Automotive Body Control Modules, Industrial Automation Controllers, Building and Elevator Control Systems, Test and Measurement Equipment TJA1041T Base TJA1041 high-speed CAN transceiver Digunakan di dalam: Powertrain and Chassis Controllers, Embedded CAN Gateways TJA1041T/3 Same-family qualification option Digunakan di dalam: Powertrain and Chassis Controllers, Embedded CAN Gateways
What is the TJA1041T/H/V?
The TJA1041T/H/V is an NXP Semiconductors high-speed CAN transceiver intended to connect a CAN protocol controller to a physical CAN bus. According to the NXP TJA1041 datasheet, it supports CAN data rates up to 1 Mbit/s, is compatible with ISO 11898, and provides differential transmit and receive paths. The device is a 14-pin SOIC transceiver rather than a complete CAN controller.
What is the maximum CAN data rate of the TJA1041T/H/V?
The TJA1041T/H/V supports CAN operation up to 1 Mbit/s. The NXP TJA1041 datasheet identifies it primarily for automotive high-speed CAN applications operating to 1 Mbit/s. Actual bus margin depends on the controller timing, cable length, termination, topology, electromagnetic environment, and compliance of the complete CAN node rather than on the transceiver rating alone.
Where can I download the TJA1041T datasheet PDF?
The official TJA1041 datasheet PDF is available from NXP at https://www.nxp.com/docs/en/data-sheet/TJA1041.pdf. The document defines the transceiver functions, electrical characteristics, operating limits, application information, and pin assignments for the TJA1041 family. Use the pin-description table in that document when assigning PCB tracks and checking the original order-code suffix.
Where can I find the TJA1041T pinout?
The TJA1041T pinout is shown in the NXP TJA1041 datasheet. The TJA1041T/H/V ordering code corresponds to a 14-pin SOIC package, but the complete pin-number and signal-name assignment should be taken directly from the pin-description table in the official PDF. This avoids assigning functions from a visually similar but electrically different CAN transceiver.
What supply voltage does the TJA1041T/H/V use?
The TJA1041T/H/V is intended for operation from a 5 V supply. The distributor product record identifies a 5 V supply, and the NXP family documentation describes a 5 V CAN transceiver for automotive high-speed CAN nodes. Confirm the permitted supply limits, decoupling requirements, and power-up behavior in the manufacturer datasheet before finalizing the board power architecture.
Is the TJA1041T/H/V still active?
The TJA1041T/H/V is marked End of Life by the NXP product information. NXP also identifies the TJA1041T as a legacy high-speed CAN transceiver. For new production, use the manufacturer’s current successor or replacement information where a pin-compatible solution is available; for maintenance of existing equipment, verify exact order-code, package, and qualification requirements before substitution.
Where can I buy the TJA1041T/H/V and check current lead time?
Use the Request a Quote form on this page to request TJA1041T/H/V availability, lead time, and minimum order quantity. Because the NXP product is marked End of Life, stock and sourcing conditions can change independently of the device specification. Include the complete ordering code TJA1041T/H/V,512 or TJA1041T/H/V,518, as applicable, when requesting a quotation.
How much does the TJA1041T/H/V cost?
The TJA1041T/H/V should be quoted through the Request a Quote form on this page rather than relying on a static price. The part is marked End of Life, and quantities, packing codes, and market availability may affect commercial terms. Submit the exact manufacturer ordering code and required quantity so the quotation can reflect the correct configuration.
Is the TJA1041T/H/V currently in stock?
Current TJA1041T/H/V stock should be confirmed through the Request a Quote form on this page. The manufacturer marks the product as End of Life, so neither prior distributor inventory nor a historical availability statement should be treated as a current stock commitment. State the required quantity and manufacturer ordering code in the request.
What is the difference between TJA1041T/H/V and TJA1041T/VM,518?
Both are 14-pin SOIC members of the TJA1041 high-speed CAN transceiver family, and comparison data lists both for 5.25 V operation at 1 Mbit/s. Their manufacturer qualification and ordering suffixes differ. According to the NXP ordering information and family datasheet, verify the temperature range, qualification code, packing code, and exact customer ordering code before treating one as a drop-in replacement.
When should I choose the TJA1041T/H/V over a newer CAN transceiver?
Choose the TJA1041T/H/V when maintaining an existing 14-pin SOIC CAN design and the exact qualified order code must be preserved. Its advantages are direct continuity with the original 1 Mbit/s ISO 11898 interface and a -40°C to +150°C operating range. For new designs, a current transceiver may be preferable when lower supply current, additional protection, wider voltage options, or newer qualification coverage is needed.
Can the TJA1041T/H/V be used in industrial CAN systems?
The TJA1041T/H/V can be used in industrial CAN systems operating at up to 1 Mbit/s because it provides a differential CANH/CANL interface and ISO 11898 compatibility. Its -40°C to +150°C range also supports extended-temperature equipment. Ensure the complete node includes a suitable CAN controller, correct bus termination, transient protection, and an EMC strategy appropriate for the installation environment.
What is the best drop-in replacement for the TJA1041T/H/V?
The closest documented same-package options are TJA1041T/VM,518 and the related TJA1041T/V,512, both listed in 14-pin SOIC packages. A drop-in decision still depends on matching the original temperature range, qualification code, and packing configuration. Use the Request a Quote form on this page for the exact replacement MPN, and consult NXP’s discontinuation and replacement documentation before production release.
Is the TJA1041T/H/V the same as TJA1041T/VM,518?
The TJA1041T/H/V and TJA1041T/VM,518 share the TJA1041 family, 14-pin SOIC package, 5.25 V rating, and 1 Mbit/s CAN capability according to the comparison listing. They are not necessarily identical for every procurement or qualification requirement because their order-code suffixes differ. Check the manufacturer ordering table for the temperature grade, tape-and-reel status, and other suffix-defined attributes.
What key specifications should engineers know about the TJA1041T/H/V?
The TJA1041T/H/V is a 5 V, 14-pin SOIC high-speed CAN transceiver rated to 1 Mbit/s and -40°C to +150°C. According to the NXP product information, it is compatible with ISO 11898, optimized for electromagnetic compatibility, has low power consumption, and becomes passive when the supply is off. It provides a physical bus interface only, so a separate CAN protocol controller remains required.

Data referensi engineering untuk TJA1041T/H/V — pembandingan, panduan desain, dan informasi konformitas.

Panduan Pemilihan

Choose the TJA1041T/H/V when repairing or reproducing an existing design that specifically requires NXP’s /H/V-qualified TJA1041 order code, a 14-pin SOIC footprint, 5 V operation, and up to 1 Mbit/s CAN communication. Its -40°C to +150°C range is particularly suitable for automotive and extended-temperature industrial equipment. TJA1041T/VM,518 is the closest documented same-package option when its qualification suffix and temperature range meet the design requirement. TJA1041T and TJA1041T/3 can support legacy family continuity, but their suffix-defined commercial and qualification conditions must be checked. For entirely new designs, evaluate current CAN transceivers with newer protection features, lower supply current, and active lifecycle status. In every case, verify pin assignments, bus timing, termination, EMC behavior, and exact manufacturer ordering codes before release.

Pembandingan dengan Alternatif

Parameter Umum Produk Ini TJA1041T/VM,518 TJA1041T/3 TJA1041T
Brand NXP Semiconductors NXP Semiconductors NXP Semiconductors NXP Semiconductors
Package SOIC-14 SOIC-14 - same SOIC-14 - same SOIC-14 - same
Product Type High-speed CAN transceiver High-speed CAN transceiver High-speed CAN transceiver High-speed CAN transceiver
Maximum CAN Data Rate 1 Mbit/s 1 Mbit/s 1 Mbit/s 1 Mbit/s
Nominal Supply Voltage 5 V 5.25 V 5 V 5 V
Bus Interface Differential CANH/CANL Differential CANH/CANL Differential CANH/CANL Differential CANH/CANL

Diferensiator Kunci

  • Broad operating temperature range for automotive and industrial CAN nodes (vsTJA1041T/VM,518)
  • Direct continuity with the specified NXP qualification suffix (vsTJA1041T)
  • Legacy 5 V, 1 Mbit/s interface preserves established PCB behavior (vsTJA1041T/3)

Catatan Desain

Place the TJA1041T/H/V, its decoupling capacitor, CANH/CANL protection components, and termination network close together. Keep the CANH and CANL traces as a short, tightly coupled pair on the PCB, avoid routing them above discontinuous power planes, and minimize the area of high-current loops. Place the transceiver near the connector or bus entry point so transient current is diverted before reaching sensitive logic.

Use split termination at the bus node when the installation environment is electrically noisy. The two resistor sections should be connected to CANL and CANCAN through the common-mode network described in the manufacturer application guidance, while preserving an effective connection to the intended reference plane. Validate the termination arrangement, chassis grounding, and common-mode choke against the system EMC requirements rather than relying on a generic layout.

Do not assume that every TJA1041 suffix is mechanically and commercially interchangeable. The package and bus speed may match, but temperature grade, qualification code, reel or tray configuration, and customer ordering code can differ. Compare the complete manufacturer ordering code and the NXP discontinuation notice before substituting a part. Also confirm that the selected CAN controller has compatible logic levels, timing, fault handling, and supply requirements.

Informasi Konformitas

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
Bebas Logam Lengket
Unknown
Bebas Halogena
Unknown
Mineral Konflik
Unknown

The TJA1041 is an automotive high-speed CAN transceiver, but no specific RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals declaration was identified in the product records. The /H suffix may encode qualification requirements; confirm the exact declaration using the manufacturer ordering and compliance information for the complete ordering code.

Data disahkan pada: 2026-11-14 — data disahkan dan disusun oleh tim engineering komponen XAIPART

Pencarian Terkait

tja1041t datasheet tja1041t datasheet pdf TJA1041T/H/V datasheet TJA1041T/H/V pinout TJA1041T/H/V replacement TJA1041T/H/V equivalent TJA1041T/H/V price TJA1041T/H/V stock TJA1041T/H/V vs TJA1041T/VM TJA1041T SOIC-14 CAN transceiver TJA1041T automotive CAN schematic NXP TJA1041T/H/V

Komponen dan Istilah Terkait

NXP Semiconductors TJA1041T/H/V TJA1041T/VM,518 TJA1041T/3 TJA1041T TJA1057GTK/3Z high-speed CAN transceiver CAN transceiver interface IC semiconductor Controller Area Network CANH CANL differential signaling ISO 11898 1 Mbit/s 5 V supply -40°C to +150°C SOIC-14 surface mount electromagnetic compatibility passive off-state behavior automotive CAN industrial automation
Kutipan Cepat RFQ
Isi detail lengkap — tim penjualan kami akan membalas dalam 24 jam
Nomor Part Manufaktur Paket QTY Harga Target Lengkap
✓
Kutipan telah disubmit!

Kami akan membalas email Anda dalam 24 jam

1
RFQ Dikirim
2
Kutipan Diterima
3
Order Ditempatkan
4
Pembayaran
5
Dikirim
6
Dikirim
Lihat Detil RFQ