TLS850B0TEV50ATMA1 - 5V 500mA 40V LDO Regulator | Infineon
MPN: TLS850B0TEV50ATMA1 ✓ AktifTLS850B0TEV50ATMA1 Ringkasan
A low-dropout (LDO) linear regulator is a type of voltage regulator that maintains a stable DC output voltage even when the input-to-output voltage headroom is small. LDOs sit in the broader hierarchy of linear regulators, which belong to voltage regulators and ultimately to the power management integrated circuit (PMIC) family. Unlike a switching DC-DC converter, an LDO dissipates VIN - VOUT as heat, trading efficiency for exceptionally low output noise and fast transient response.
Key features include a 3.0 V to 40 V input voltage range suitable for direct connection to 12 V or 24 V automotive batteries (including load-dump transients), a fixed 5.0 V output with ±2% accuracy, 500 mA continuous output current, a 100 mV typical (and 250 mV worst-case) dropout at full load, and a 20 µA typical quiescent current that preserves standby energy in always-on subsystems. The IC integrates thermal shutdown, output current limiting, and a power-good output for rail monitoring, and the PG-TO252-5 tab provides a low θJA thermal path for sustained high-current operation.
Internally, the TLS850B0TEV50ATMA1 uses a PNP-pass architecture with a precision bandgap reference and a closed-loop error amplifier. The 100 mV typical dropout minimizes the required input-to-output headroom, which in turn reduces on-die power dissipation and improves thermal performance at high line. The 20 µA quiescent current keeps battery drain low during key-off or sleep modes, while internal protection blocks (Overtemperature, Overcurrent) safeguard the pass element under fault conditions.
Typical applications include automotive body and chassis ECUs (body control modules, instrument clusters, HVAC controllers), 24 V industrial sensor supplies, PLC and HMI power rails, LED driver biasing, and always-on standby rails in battery-connected systems. The 40 V input rating and Infineon OPTIREG robustness make it a direct match for the harsh electrical environments of vehicle powernet and industrial bus systems.
When designing with this part, observe the input/output capacitor selection in the manufacturer datasheet - typically a 1 µF to 10 µF ceramic with low ESR on both rails - and verify the PG-TO252-5 copper area on the PCB keeps the junction temperature below 150 °C at worst-case VIN and full 500 mA load. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.
Alternatif penggantian untuk TLS850B0TEV50ATMA1 — paket yang sama, pin-pada-pin kompatibel. Bagian paket yang berbeda memerlukan kerja ulang PCB diabaikan.
Variasi di dalam seri ini
Model-series yang sama yang kompatibel dengan penggantian TLS850B0TEV50ATMA1 (sama faktor bentuk dan footprint) — berbeda di dalam Package, Output Voltage, Protection Features, Input Voltage Range, Maximum Output Current.
TLS850B0TEV33ATMA1
✅ Drop-In ⚠️ Spesifikasi Tidak Disahkan📋 Alternatif referensi (tidak dalam katalog)
TLS850B0TEV33XUMA1
✅ Drop-In ⚠️ Spesifikasi Tidak Disahkan📋 Alternatif referensi (tidak dalam katalog)
TLS835B2ELVSEXUMA1
✅ Drop-InKontak untuk harga
Lihat Datasheet →TLE42744DV50ATMA1
✅ Drop-InKontak untuk harga
Lihat Datasheet →TLS850B0TEV50ATMA1 Rating Maksimal & Karakteristik Listrik
| Topologi | Low-Dropout (LDO) Linear Regulator |
| Tipe Output | Fixed 5.0 V |
| Rentang Tegangan Masukan | 3.0 V to 40 V |
| Output Voltage Accuracy | ±2% (max) |
| Output Current Capability | Up to 500 mA |
| Tegangan Turun | 100 mV typical at full load |
| Arus Memerintah | 20 µA typical |
| Tegangan Output | 5.0 V |
| Jumlah Output | 1 |
| Output Polarity | Positive |
| Output Power Good | Yes |
| Penutupan Panas | Yes (internal) |
| Output Current Limit | Yes (internal) |
| Paket | PG-TO252-5 (DPAK, 4 leads + tab) |
| Tipe Mounting | Surface Mount |
| Status RoHS | Compliant |
| Product Family | OPTIREG linear TLS850B0TE |
Konfigurasi Pin TLS850B0TEV50ATMA1
| Pin produk 1 | IN — Input voltage supply (3.0 V to 40 V) |
| Pin produk 2 | GND — Ground |
| Pin produk 3 | PG — Power-Good output (open-drain/active-high per datasheet) |
| Pin produk 4 | OUT — Regulated 5.0 V output |
| Pin produk 5 | TAB — Exposed thermal tab - tie to GND for heatsinking |
Aplikasi Umum
TLS850B0TEV50ATMA1 cocok untuk 6 aplikasis: Automotive Body Control Module (BCM) 5V Rail, Industrial 24V PLC/HMI Power Supply, Sensor and Actuator 5V Bias Supply, Battery-Connected Always-On Standby Rail, Automotive Instrument Cluster 5V Supply, HVAC and Climate Control Module.
Automotive Body Control Module (BCM) 5V Rail
The TLS850B0TEV50ATMA1 fits automotive body and chassis ECU rails because of its 3.0 V to 40 V input, 5.0 V fixed output, and 500 mA capability. Its 40 V maximum input rating tolerates load-dump transients directly without external TVS clamping, simplifying the front-end filter. The 20 µA typical quiescent current keeps drain low during key-off and standby states, while the power-good output gives the host MCU a clean rail-valid signal for sequencing. With 100 mV typical dropout it also rides through cold-crank dips on the 12 V battery. The PG-TO252-5 package is footprint-compatible with existing BCM designs using DPAK-5 linear regulators.
Direkomendasikan
Industrial 24V PLC/HMI Power Supply
The TLS850B0TEV50ATMA1 is a good fit for 24 V industrial PLC and HMI rails because it accepts up to 40 V at the input, well above the nominal 24 V bus plus its typical transient envelope. Its 500 mA continuous output current is sufficient for a 5 V MCU plus a few digital isolators and signal-conditioning ICs. The 20 µA typical quiescent current keeps standby losses small in always-on industrial controllers. Internal thermal shutdown and current limiting protect the regulator from sustained overload and from inrush transients common on industrial busses.
Direkomendasikan
Sensor and Actuator 5V Bias Supply
Sensor and actuator subsystems in industrial machinery often require a clean, low-noise 5 V rail at modest currents. The TLS850B0TEV50ATMA1's low quiescent current and 5 V fixed output make it ideal for always-on sensor biasing that remains powered when the main controller sleeps. The wide 3.0 V to 40 V input tolerates noisy 24 V industrial busses without external pre-regulation. The PG output provides a rail-valid flag to the MCU so it can safely read sensor data only after the 5 V rail has settled.
Direkomendasikan
Battery-Connected Always-On Standby Rail
Battery-connected always-on systems such as telematics units, e-bike controllers and remote sensors require a quiescent-current-minimized 5 V rail that stays alive in deep sleep. The TLS850B0TEV50ATMA1's 20 µA typical quiescent current minimizes standby losses on a 12 V or 24 V battery. Its 40 V input rating handles jump-start transients on 12 V systems without external protection. The 5 V fixed output is suitable for always-on MCUs and RTC circuits, and the PG output can wake the main controller once the rail is stable.
Direkomendasikan
Automotive Instrument Cluster 5V Supply
Instrument clusters and dashboard modules need a clean 5 V rail for display drivers, stepper motors and indicator LEDs. The TLS850B0TEV50ATMA1 provides up to 500 mA at 5 V fixed, which is enough to drive the cluster logic, gauge drivers and small backlight sub-rails. Its wide input voltage range tolerates cranking and load-dump on the 12 V automotive bus, and its exposed PG-TO252-5 tab dissipates heat efficiently in the confined dashboard enclosure. The power-good output can reset the cluster MCU cleanly on rail-valid edges.
Direkomendasikan
HVAC and Climate Control Module
HVAC and climate control ECUs in vehicles draw continuous current for fan drivers, sensor bias and communication transceivers, all from a 5 V rail. The TLS850B0TEV50ATMA1's 500 mA capability and 5 V fixed output match the HVAC module's supply requirement. Its 40 V input rating allows direct connection to the 12 V or 24 V vehicle bus without a pre-regulator. The 20 µA quiescent current keeps drain low during idle periods, and the power-good output gives the HVAC controller a clean enable signal after the rail settles.
Direkomendasikan
Ringkasan Produk Direkomendasikan
Data referensi engineering untuk TLS850B0TEV50ATMA1 — pembandingan, panduan desain, dan informasi konformitas.
Panduan Pemilihan
Pembandingan dengan Alternatif
| Parameter Umum | Produk Ini | TLS850B0TEV33ATMA1 | TLS850B0TEV33XUMA1 | TLS835B2ELVSEXUMA1 | TLE42744DV50ATMA1 |
|---|---|---|---|---|---|
| Brand | Infineon | Infineon | Infineon | Infineon | Infineon |
| Package | PG-TO252-5 (DPAK) | PG-TO252-5 (DPAK) | PG-TO252-5 (DPAK) | PG-TO252-5 (DPAK) | PG-TO252-7 (DPAK-7) |
| Output Voltage | 5.0 V | 3.3 V | 3.3 V | 3.3 V | 5.0 V |
| Output Current | 500 mA | 500 mA | 500 mA | 500 mA | 500 mA |
| Input Voltage Range | 3.0 V to 40 V | 3.0 V to 40 V | 3.0 V to 40 V | 3.0 V to 40 V | Up to 45 V |
| Dropout Voltage | 100 mV typical at 500 mA | 100 mV typical at 500 mA | 100 mV typical at 500 mA | Similar very-low-dropout family | Similar low-dropout OPTIREG family |
| Pin Count | 5 | 5 | 5 | 5 | 7 |
| Power-Good Output | Yes | Yes | Yes | Yes | Yes |
Diferensiator Kunci
- Very low quiescent current of 20 µA typical (vsTLE42744DV50ATMA1)
- Wide 3.0 V to 40 V input voltage range (vsTLE42744DV50ATMA1)
- 5-pin DPAK footprint for compact layouts (vsTLE42744DV50ATMA1 (DPAK-7))
- Built-in power-good (PG) output for sequencing (vsTLS850B0TEV33ATMA1)
Catatan Desain
Estimated: at VIN = 24 V, VOUT = 5.0 V and IOUT = 500 mA, power dissipation PD = (VIN - VOUT) × IOUT = 19 V × 0.5 A = 9.5 W. With a PG-TO252-5 θJA of approximately 30 C/W on 1 square inch of copper, the junction temperature rise is about 285 C above ambient, which exceeds the 150 C thermal shutdown threshold. For 24 V input applications, derate the load to ~250 mA or add a larger copper area / external heatmap. At 12 V input, full 500 mA output dissipates 3.5 W, which is comfortable on a 1 square inch copper pour.
Place the input capacitor as close as possible to the IN pin and the output capacitor as close as possible to the OUT pin. The Infineon datasheet recommends a 1 µF to 10 µF ceramic capacitor with low ESR on both rails, and a minimum of 1 µF effective capacitance is required for stability. The exposed thermal tab must be soldered to a copper pour that ties to ground, and the copper area determines the achievable θJA. Use wide, short traces for IN, OUT and GND to minimize parasitic impedance and voltage transients.
Do not exceed the absolute maximum input voltage of 40 V, including load-dump transients. The regulator does not contain internal TVS protection on the input rail, so for harsh automotive environments an external TVS or resistor-zener clamp may be required. Always respect the PG-TO252-5 power dissipation budget: at high VIN - VOUT deltas (for example 24 V to 5 V at full load), the die will hit thermal shutdown unless the load is derated or the copper area is increased.
Keep the power-ground path short and direct - connect the input capacitor, output capacitor, GND pin and thermal tab to a single low-impedance ground plane. Avoid routing noisy switching signals across the OUT node or over the feedback/adjust traces. A small bead or ferrite on the input rail can further attenuate switching noise from upstream DC-DC converters, which is important if the TLS850B0TEV50ATMA1 is used as a post-regulator for an audio or RF analog rail.
Informasi Konformitas
AEC-Q100 qualified as part of the OPTIREG linear automotive family per Infineon product page. RoHS and REACH compliant per DigiKey listing.
