Texas Instruments

TMS320BC51PZ100 - 100MHz 16-Bit DSP | Texas Instruments

MPN: TMS320BC51PZ100 ✗ Akhir Hidup
100-LQFP Package 100 MHz Speed
MOQ: 1 |

TMS320BC51PZ100 Ringkasan

Texas Instruments TMS320BC51PZ100 is an obsolete 16-bit fixed-point digital signal processor operating at 100 MHz with 50 MIPS performance, supplied in a 100-lead LQFP package measuring 14 x 14 mm. The processor is designed for embedded signal-processing workloads requiring deterministic arithmetic, dedicated peripheral interfaces, and a high pin-count package that exposes a broad set of signal-chain and control connections.

A digital signal processor, or DSP, is a microprocessor optimized for repetitive numerical operations such as filtering, Fourier analysis, modulation, and waveform generation. Unlike a general-purpose processor, the TMS320BC51 architecture emphasizes parallel arithmetic, dedicated memory organization, and predictable execution of signal-processing algorithms. Within the product hierarchy, it belongs to the Texas Instruments TMS320 family of programmable digital signal processors and digital signal processors/controllers.

The most prominent identified characteristics are a 100 MHz clock rating, 16-bit processing format, 50 MIPS throughput, and a 100-LQFP package. The commercial temperature grade and surface-mount construction make the device suitable for legacy industrial, communications, audio-control, and embedded instrumentation designs in which the original processor architecture and PCB footprint remain established. Its obsolete lifecycle status means new designs should normally select a currently supported processor, while existing equipment may require a carefully qualified repair source.

The fixed-point architecture is important when evaluating an upgrade. Algorithms written around the TMS320BC51's 16-bit numeric format and peripheral behavior may not transfer directly to a floating-point DSP or a general-purpose microcontroller. Migration can therefore require changes to word length, scaling, memory mapping, initialization procedures, and real-time task scheduling. Clock rate alone does not make a modern controller a functional substitute: memory architecture, timing, peripherals, development tools, and software compatibility can dominate the replacement decision.

The 100 MHz rating supports computationally intensive loops, but application performance still depends on the implemented instruction mix, memory configuration, bus utilization, peripheral activity, and interrupt load. The 50 MIPS figure describes nominal instruction throughput rather than a guaranteed application result. Designers should profile representative signal chains and include realistic worst-case latency when evaluating control loops, communications framing, or audio processing.

Typical uses include industrial signal conditioning, communications modem functions, audio and control processing, instrumentation, and embedded systems that were designed around the TMS320BC51 family. A replacement project must verify package dimensions, pin functions, signal levels, clock requirements, memory interface behavior, peripheral compatibility, and software support before committing to a new processor.

This page combines the identified device characteristics, lifecycle information, package details, sourcing guidance, and practical migration considerations. It also distinguishes exact hardware compatibility from merely similar DSP functions, helping engineers determine whether a board can be reused or whether the processor, firmware, and surrounding circuitry require redesign.

Alternatif penggantian untuk TMS320BC51PZ100 — paket yang sama, pin-pada-pin kompatibel. Bagian paket yang berbeda memerlukan kerja ulang PCB diabaikan.

Variasi di dalam seri ini

Model-series yang sama yang kompatibel dengan penggantian TMS320BC51PZ100 (sama faktor bentuk dan footprint) — berbeda di dalam Processor Type.

Texas Instruments
Processor Type: Fixed-point digital signal processor (DSP)
Bandingkan dengan TMS320BC51PZ100 →

TMS320BC51PZP100

✅ Drop-In ⚠️ Spesifikasi Tidak Disahkan
📦 100-LQFP (14 x 14 mm)
Same TMS320BC51 family and 100-LQFP footprint; nominal clock rating is 100 MHz for both, with no quantified electrical difference stated.

📋 Alternatif referensi (tidak dalam katalog)

TMS320BC51PZP120

✅ Drop-In ⚠️ Spesifikasi Tidak Disahkan
📦 100-LQFP (14 x 14 mm)
Same TMS320BC51 family and 100-LQFP footprint; 120 MHz nominal clock is 20% higher than the 100 MHz target.

📋 Alternatif referensi (tidak dalam katalog)

TMS320BC51PZP80

✅ Drop-In ⚠️ Spesifikasi Tidak Disahkan
📦 100-LQFP (14 x 14 mm)
Same TMS320BC51 family and 100-LQFP footprint; 80 MHz nominal clock is 20% lower than the 100 MHz target.

📋 Alternatif referensi (tidak dalam katalog)

TMS320BC51PZP60

✅ Drop-In ⚠️ Spesifikasi Tidak Disahkan
📦 100-LQFP (14 x 14 mm)
Same TMS320BC51 family and 100-LQFP footprint; 60 MHz nominal clock is 40% lower than the 100 MHz target and exceeds the 30% proximity limit.

📋 Alternatif referensi (tidak dalam katalog)

TMS320BC51PZ100 Spesifikasi

Processor Type Fixed-Point Digital Signal Processor
Word Length 16 bit
Frekuensi Bawah Maximum 100 MHz
Instruction Throughput 50 MIPS
Architecture TMS320 fixed-point DSP
Package Type 100-LQFP
Package Dimensions 14 x 14 mm
Number of Terminals 100
Package Code LFQFP
Package Shape Square
Gaya Mounting Surface Mount
Terminal Form Gull Wing
Temperature Grade Commercial
Status RoHS ROHS3 Compliant
Status Lingkungan Hidup Obsolete

TMS320BC51PZ100 square Diamant Konfigurasi Panduan

Konfigurasi pin untuk TMS320BC51PZ100 (square pakai pakai). Penomoran pin, fungsi, dan diagram koneksi ditetapkan dalam datasheet produsen. Lihatnya untuk footprint dan pedoman perpindahan paruh.

Diamant diagram pakai pakai square untuk TMS320BC51PZ100

Tidak ada data diatribut pin yang tersedia untuk TMS320BC51PZ100.

Lihat ke: datasheet produk untuk konfigurasi pin penuh.

Aplikasi Umum

TMS320BC51PZ100 cocok untuk 6 aplikasis: Industrial Signal Conditioning, Communications Modem Processing, Audio Control and Effects, Measurement and Instrumentation, Fixed-Point Control Loops, Embedded Data Acquisition.

🏭

Industrial Signal Conditioning

The TMS320BC51PZ100 is suited to legacy industrial signal-conditioning equipment that performs filtering, scaling, and real-time control at a 100 MHz nominal clock. Its 16-bit fixed-point format supports deterministic integer arithmetic, while the 50 MIPS rating provides substantial nominal throughput for repetitive numerical loops. In an existing installation, the processor can preserve proven control behavior without modifying the hardware architecture. For a new controller, verify voltage limits, peripheral assignments, memory behavior, and operating-temperature requirements against the manufacturer datasheet. Because the lifecycle status is obsolete, use the part primarily for equipment maintenance and compare any modernization project against the cost of firmware and PCB changes.

🌐

Communications Modem Processing

The TMS320BC51PZ100 can support legacy communications modem functions that depend on fixed-point filtering, symbol processing, and precise interrupt-driven I/O. Its 100 MHz clock and 50 MIPS instruction throughput are useful for sustained arithmetic, but actual modem performance depends on the selected instruction mix, memory wait states, and peripheral activity. When repairing a communications board, preserve the original clock tree and timing assumptions because changing processor speed can alter interrupt margins and buffer management. A direct same-family speed-grade change may retain the package while requiring validation of clock-dependent behavior. Confirm protocol timing, data-interface levels, and real-time deadlines before approving the component for field use.

🎧

Audio Control and Effects

The TMS320BC51PZ100 can be used in legacy audio-control and effects equipment where sample-rate processing, gain calculation, mixing, and equalization must run deterministically. Its 16-bit fixed-point architecture aligns with many classic audio DSP algorithms, allowing existing code to retain established scaling and rounding behavior. The 100 MHz nominal clock provides ample instruction-level capacity, although the final signal-chain performance depends on memory configuration, serial-port throughput, and interrupt latency. When substituting a speed-grade variant, verify that clocks, timers, and serial interfaces still meet the original timing envelope. The obsolete lifecycle status makes supply continuity and long-term maintenance the primary sourcing concerns.

🔧

Measurement and Instrumentation

The TMS320BC51PZ100 is appropriate for maintaining legacy instrumentation that performs acquisition conditioning, digital filtering, calibration, and display-data processing. A 16-bit fixed-point DSP can implement the arithmetic needed in measurement chains, while the 100 MHz clock and 50 MIPS rating support real-time workloads with limited general-purpose overhead. The 100-LQFP package exposes enough terminals for parallel data, control, memory, and serial peripheral connections. For a repair, use the manufacturer pin-description table to preserve signal routing and verify analog-interface circuitry separately. For new measurement products, a currently supported processor is usually preferable because it reduces lifecycle, documentation, and software-tooling risk.

⚙️

Fixed-Point Control Loops

The TMS320BC51PZ100 can execute deterministic fixed-point control loops where repeatable arithmetic and direct peripheral access are more important than floating-point convenience. Its 100 MHz clock provides a 10 ns nominal clock period, but control latency must be calculated from the actual instruction sequence, memory access pattern, interrupt latency, and peripheral timing. Existing control firmware may therefore be reused most effectively with a device having the same architecture and comparable clock behavior. When comparing speed grades, rerun worst-case timing analysis rather than assuming that a faster clock preserves every interrupt threshold or buffer schedule. Confirm processor voltage, peripheral clock, and thermal conditions through the datasheet.

🧩

Embedded Data Acquisition

The TMS320BC51PZ100 can support embedded data-acquisition systems that combine sensor conditioning, sampled-data processing, and host communication in one programmable processor. Its 16-bit fixed-point format is well matched to many legacy acquisition algorithms, and the 50 MIPS rating allows filtering and numerical preprocessing without relying solely on an external processor. The 100-LQFP package supports a broad interface arrangement, including memory and peripheral connections. When repairing or qualifying a same-family substitute, check conversion timing, serial framing, interrupt priorities, and bus timing, not merely the nominal clock. Because the part is obsolete, request supply condition and traceability through the Request a Quote form.

What is the TMS320BC51PZ100?
The TMS320BC51PZ100 is a Texas Instruments 16-bit fixed-point digital signal processor rated at 100 MHz and 50 MIPS. It is packaged in a 100-lead LQFP measuring 14 x 14 mm and is intended for embedded filtering, communications, control, audio, and instrumentation applications. The manufacturer classifies the device as obsolete, so it is primarily relevant to maintenance, repair, and previously designed embedded systems rather than new product development.
What are the key specifications of TMS320BC51PZ100 that engineers should know?
The principal TMS320BC51PZ100 specifications are a 100 MHz maximum clock, 50 MIPS instruction throughput, 16-bit processing format, and 100-LQFP package. The device is a fixed-point digital signal processor with a commercial temperature grade and a square gull-wing surface-mount package measuring 14 x 14 mm. According to the Texas Instruments product information and distributor records, the part is obsolete and marked ROHS3 compliant. Detailed voltage, memory, and pin-function limits must be taken from the manufacturer datasheet.
Where can I download the TMS320BC51PZ100 datasheet PDF?
The TMS320BC51PZ100 datasheet can be downloaded through the linked Texas Instruments documentation or the AllDataSheet datasheet page on this product page. The manufacturer datasheet is the controlling source for the complete pin description, electrical characteristics, memory organization, peripheral operation, timing, and application information. The available search record identifies a 91-page document, but no revision identifier is shown, so the PDF itself should be checked before using a specific revision for design or repair documentation.
Where can I find the TMS320BC51PZ100 pinout?
The complete 100-pin assignment must be taken from the pin-description table in the Texas Instruments TMS320BC51PZ100 datasheet; the commercial search results confirm the 100-LQFP package but do not reproduce individual terminal names. Use the manufacturer table when assigning PCB tracks, especially for clock, memory, serial-port, parallel-interface, power, and ground pins. Do not infer pin compatibility from the square package shape alone, because package dimensions do not establish identical peripheral or signal routing.
Is the TMS320BC51PZ100 still active?
No. The TMS320BC51PZ100 is classified as obsolete in the available product and distributor records. Existing industrial, communications, audio, and control systems may still contain the device, but long-term continuity depends on residual inventory and independent sourcing. For new designs, select a currently supported processor and budget for firmware migration rather than treating an obsolete stock channel as a product-lifecycle commitment.
What is the difference between fixed-point and floating-point processing for TMS320BC51PZ100?
The TMS320BC51PZ100 is identified as a 16-bit fixed-point DSP, so numerical scaling and integer arithmetic are central to its operation. A floating-point alternative may avoid many scaling procedures but can change instruction behavior, memory use, timing, and firmware structure. According to the manufacturer product classification, the target processor uses fixed-point processing. A replacement must therefore be validated at the algorithm level rather than selected solely from clock frequency or package dimensions.
Where can I buy TMS320BC51PZ100 online?
Use the Request a Quote form on this page to request TMS320BC51PZ100 availability, condition, lot traceability, and a quotation. Because the manufacturer classifies the part as obsolete, supply may depend on remaining factory or channel inventory rather than an active production roadmap. Ask the supplier to identify the exact MPN, package, date code, and any documented test or inspection status before committing the component to a maintenance order.
What is the price of TMS320BC51PZ100?
Current commercial availability and the final delivered quotation should be requested through the Request a Quote form on this page. The TMS320BC51PZ100 is obsolete, and the available web records do not contain qualifying quantity-break pricing for this exact MPN. For budget planning, request the quantity needed, package form, condition, traceability requirements, and delivery schedule so that any residual inventory can be evaluated as a complete maintenance supply rather than as a generic catalog line.
What is the lead time for TMS320BC51PZ100?
The current lead time for TMS320BC51PZ100 should be confirmed through the Request a Quote form on this page. Because the device is obsolete, lead time depends on remaining lot size, traceability, inspection, and whether the seller has physical stock rather than a factory schedule. State the required quantity and target delivery date in the request, and ask for a written confirmation before treating the component as available for a production repair schedule.
Is TMS320BC51PZ100 in stock?
Stock status for TMS320BC51PZ100 should be requested through the Request a Quote form on this page. One distributor record mentions a quantity of 76, but that observation is not a guarantee of current inventory and does not establish lot traceability or condition. Request a fresh confirmation that includes the package form, date code, quantity, and testing status before scheduling installation or placing the order.
What can replace TMS320BC51PZ100?
A valid replacement for TMS320BC51PZ100 must satisfy four separate checks: package and land-pattern compatibility, electrical operating limits, peripheral and memory-interface compatibility, and firmware compatibility. The cross-reference searches did not identify a manufacturer-confirmed cross-brand drop-in replacement. Same-family speed variants can share the 100-LQFP architecture, but a clock-rate change alone does not guarantee drop-in equivalence. A processor migration may require new firmware, memory changes, and board-level verification.
Can TMS320C203PZ80 replace TMS320BC51PZ100?
The TMS320C203PZ80 should not be treated as a drop-in replacement merely because comparison information lists it with the same 100-LQFP package. The available comparison establishes package similarity, but it does not establish identical pin functions, memory interfaces, peripherals, voltage levels, or software behavior. Use the TMS320C203PZ80 only as a redesign candidate after comparing both datasheets and validating the complete board; use the Request a Quote form for a separate quotation.
TMS320BC51PZ100 vs TMS320VC5409PGE100 - which is better for a legacy DSP upgrade?
TMS320BC51PZ100 is preferable when preserving an existing 100 MHz, 16-bit fixed-point TMS320BC51 design is essential, whereas TMS320VC5409PGE100 should be evaluated as a different-generation platform with its own software and system requirements. The available comparison confirms that these are not automatically equivalent parts. Final selection depends on pin mapping, clocking, memory, peripherals, operating voltages, code compatibility, and the amount of redesign the project can accept.
When should I choose TMS320BC51PZ100 over a modern DSP or MCU?
Choose TMS320BC51PZ100 only when maintaining an existing board, reusing proven fixed-point firmware, or matching an unavailable legacy architecture outweighs the lifecycle risk. A modern DSP or microcontroller is generally preferable for new designs because it provides current documentation, ongoing availability, and newer development tools. For the target device, preserve the original memory map, interrupt model, peripherals, and timing assumptions, and request supply through the Request a Quote form before committing to a repair program.
Is TMS320BC51PZ100 suitable for industrial signal-processing equipment?
The TMS320BC51PZ100 can be suitable for maintaining legacy industrial signal-processing equipment because it combines a 100 MHz fixed-point DSP with a broad 100-LQFP interface package. Its commercial temperature grade and obsolete lifecycle status limit its attractiveness for new industrial platforms, however. Confirm the exact operating-temperature requirements, supply condition, and long-term availability from the manufacturer datasheet and the Request a Quote form before using it in safety-related or production-maintenance equipment.

Data referensi engineering untuk TMS320BC51PZ100 — pembandingan, panduan desain, dan informasi konformitas.

Panduan Pemilihan

Choose the original TMS320BC51PZ100 when an established system must retain its exact processor speed, timing behavior, and supply identity, particularly during qualified maintenance. A same-family 100 MHz variant is the closest choice when its complete pin and electrical characteristics match. A 120 MHz option may improve compute margin but requires renewed worst-case timing and thermal validation; an 80 MHz option reduces compute margin by 20% and may miss real-time deadlines. None of these family variants should be selected solely from package dimensions. For a new design, prefer a currently supported DSP because the target is obsolete. For a functional redesign, TMS320C203PZ80 and TMS320VC5409PGE100 may serve as investigation starting points, but they require complete pin, electrical, peripheral, memory, and firmware review rather than a drop-in assumption.

Pembandingan dengan Alternatif

Parameter Umum Produk Ini TMS320BC51PZP100 TMS320BC51PZP120 TMS320BC51PZP80 TMS320BC51PZP60
Brand Texas Instruments Texas Instruments Texas Instruments Texas Instruments Texas Instruments
Package 100-LQFP (14 x 14 mm) 100-LQFP (14 x 14 mm) 100-LQFP (14 x 14 mm) 100-LQFP (14 x 14 mm) 100-LQFP (14 x 14 mm)
Maximum Clock Frequency 100 MHz 100 MHz 120 MHz 80 MHz 60 MHz
Clock Difference From Target 0 MHz 0 MHz +20 MHz (+20%) -20 MHz (-20%) -40 MHz (-40%)
Processor Type 16-bit fixed-point DSP TMS320BC51 fixed-point DSP TMS320BC51 fixed-point DSP TMS320BC51 fixed-point DSP TMS320BC51 fixed-point DSP
Number of Terminals 100 100 100 100 100

Diferensiator Kunci

  • Exact nominal clock match within the TMS320BC51 family (vsTMS320BC51PZP100)
  • Lower clock deviation than higher-speed family options (vsTMS320BC51PZP120)
  • Higher nominal clock than the 80 MHz family option (vsTMS320BC51PZP80)

Catatan Desain

Do not treat a same-package processor as electrically and functionally interchangeable. Before replacing TMS320BC51PZ100, compare the manufacturer pin-description tables for power, ground, clocks, memory, serial interfaces, interrupts, and unused terminals. A 100-LQFP outline alone does not prove that all peripheral functions or software timing remain identical.

Validate clock quality, memory timing, and serial-interface timing on the assembled board rather than relying only on nominal clock ratings. The processor's 100 MHz rating corresponds to a 10 ns nominal clock period, but real timing margins depend on trace loading, external component tolerances, memory wait states, and bus activity. Compare oscilloscope measurements at the relevant processor and peripheral pins before approving a speed-grade substitution.

Check junction temperature and supply dissipation against the manufacturer datasheet after identifying the actual core and I/O voltage values. The 100-LQFP package provides substantial thermal copper area, but its thermal performance still depends on board copper, airflow, and neighboring heat sources. Use a temperature margin appropriate for the equipment's ambient range and obtain the complete electrical limits from the datasheet before conducting thermal testing.

Preserve the original component footprint, exposed power connections, and decoupling strategy when repairing a populated board. Place the replacement only after checking pin-1 orientation and soldering temperature limits for the package and assembly. Because complete pin functions are not reproduced in the commercial listings, use the manufacturer pin-description table to confirm every connection before applying power.

Informasi Konformitas

RoHS
Compliant
REACH
Unknown
AEC-Q100
Not Applicable
Bebas Logam Lengket
Unknown
Bebas Halogena
Unknown
Mineral Konflik
Unknown

The distributor product record identifies the TMS320BC51PZ100 as ROHS3 Compliant. No additional REACH, lead-free, halogen-free, conflict-minerals, or automotive qualification information was identified.

Data disahkan pada: 2026-11-14 — data disahkan dan disusun oleh tim engineering komponen XAIPART

Pencarian Terkait

TMS320BC51PZ100 TMS320BC51PZ100 datasheet TMS320BC51PZ100 datasheet pdf TMS320BC51PZ100 pinout TMS320BC51PZ100 specifications TMS320BC51PZ100 equivalent TMS320BC51PZ100 replacement TMS320BC51PZ100 cross reference TMS320BC51PZ100 price TMS320BC51PZ100 stock Texas Instruments TMS320BC51PZ100 TMS320BC51PZ100 100MHz 50 MIPS TMS320BC51PZ100 100-LQFP footprint TMS320BC51PZ100 industrial DSP TMS320BC51PZ100 vs TMS320C203PZ80

Komponen dan Istilah Terkait

Texas Instruments TMS320BC51PZ100 TMS320BC51PZP100 TMS320BC51PZP120 TMS320BC51PZP80 TMS320BC51PZP60 TMS320C203PZ80 TMS320VC5409PGE100 digital signal processor DSP fixed-point processor 16-bit processor TMS320 architecture signal processing embedded processing 100 MHz clock 50 MIPS throughput 100-LQFP LFQFP QFP package family surface-mount technology SMD industrial signal conditioning communications modem processing RoHS ROHS3 Compliant
Kutipan Cepat RFQ
Isi detail lengkap — tim penjualan kami akan membalas dalam 24 jam
Nomor Part Manufaktur Paket QTY Harga Target Lengkap
✓
Kutipan telah disubmit!

Kami akan membalas email Anda dalam 24 jam

1
RFQ Dikirim
2
Kutipan Diterima
3
Order Ditempatkan
4
Pembayaran
5
Dikirim
6
Dikirim
Lihat Detil RFQ