TPS65988DDK - Dual-Port USB Type-C PD Controller | Texas Instruments
MPN: TPS65988DDK ✓ AktifTPS65988DDK Ringkasan
A USB Type-C and Power Delivery controller is a specialized power management IC that negotiates voltage, current, and role (source/sink) over the USB Type-C Configuration Channel (CC) lines using the USB PD protocol. Within the broader semiconductor hierarchy it sits inside the power management IC family, alongside LDOs, DC/DC converters, and battery chargers, but it is functionally distinct because it owns the protocol state machine, policy engine, and physical-layer (PHY) logic defined by the USB Implementers Forum. Pairing the PD controller with downstream power stages or load switches produces a complete USB-C port solution.
Key features of the TPS65988DDK include USB PD 3.0 compliance with fast role swap, integrated 5 A bidirectional power switches, support for DisplayPort and USB4 alternate modes, configurable boot or host-controlled modes, and I2C/SPI host interface for policy updates. Robust protection features include over-voltage, over-current, over-temperature, and reverse-current blocking on the VBUS path, allowing safe hot-plug behavior in laptops, docks, and monitors.
Typical applications include dual-port USB-C docking stations, Thunderbolt 4 / USB4 hosts, gaming monitors with USB-C input, industrial PCs, and any system that must route 20 V / 5 A from a Type-C connector while supporting alternate-mode video. The wide VBUS range and integrated mux control reduce external component count and simplify PCB layout for slim platforms.
When designing with the TPS65988DDK, careful attention must be paid to VBUS capacitance budgets (USB PD spec limits the inrush charge) and to CC-pin pull-up/pull-down choices that set the default role (sink vs source). Firmware configuration is typically supplied through external EEPROM, and GPIOs are reserved for control of external DC/DC converters and high-speed data muxes.
This page synthesizes distributor pricing, same-family drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone.
Alternatif penggantian untuk TPS65988DDK — paket yang sama, pin-pada-pin kompatibel. Bagian paket yang berbeda memerlukan kerja ulang PCB diabaikan.
TPS65988DHRSHR
✅ Drop-In📋 Alternatif referensi (tidak dalam katalog)
TPS65988DKRSHR
✅ Drop-In📋 Alternatif referensi (tidak dalam katalog)
TPS65988DDK Rating Maksimal & Karakteristik Listrik
| Fungsi | Dual-port USB Type-C and USB PD controller |
| USB Specification | USB Power Delivery 3.0 (USB-IF certified, TID# 1099) |
| Number of Type-C Ports | 2 |
| Operating Power Role | Source and Sink (DRP / dual-role capable) |
| Maximum VBUS Voltage | 20 V |
| Maximum VBUS Current | 5 A per port |
| Integrated Power Switches | 25 mOhm bidirectional FETs |
| Alternate Mode Support | DisplayPort, USB4 |
| Fast Role Swap | Supported |
| Host Interface | I2C / SPI |
| Configuration Mode | Configurable at boot or host-controlled |
| Paket | 56-VQFN (7x7 mm) |
| Rentang Suhu Kerja | -40C to +85C |
| Tipe Mounting | Surface Mount |
| Compliance | USB-IF certified PD3.0 (TID# 1099), RoHS compliant |
| Control of External Peripherals | DC/DC supplies, high-speed data muxes via GPIO |
Konfigurasi Pin TPS65988DDK
| Pin produk 1 | GND — Thermal pad and ground reference |
| Pin produk 2 | CC1_1 — Configuration Channel 1, port 1 |
| Pin produk 3 | CC2_1 — Configuration Channel 2, port 1 |
| Pin produk 4 | VBUS_1 — VBUS sense / power path, port 1 |
| Pin produk 5 | SRC_1 — Source path control, port 1 |
| Pin produk 6 | SNK_1 — Sink path control, port 1 |
| Pin produk 7 | GPO_1 — General purpose output 1 |
| Pin produk 8 | GPO_2 — General purpose output 2 |
| Pin produk 9 | I2C_SCL — I2C clock (host interface) |
| Pin produk 10 | I2C_SDA — I2C data (host interface) |
| Pin produk 11 | SPI_CLK — SPI clock (alternate interface) |
| Pin produk 12 | SPI_MOSI — SPI master-out slave-in |
| Pin produk 13 | SPI_MISO — SPI master-in slave-out |
| Pin produk 14 | SPI_CS — SPI chip select |
| Pin produk 15 | INT — Interrupt output (active low) to host |
| Pin produk 16 | RESET — Reset input (active low) |
| Pin produk 17 | EEPROM_SCL — External EEPROM I2C clock |
| Pin produk 18 | EEPROM_SDA — External EEPROM I2C data |
| Pin produk 19 | VBUS_FRS — VBUS fast role swap sense |
| Pin produk 20 | AUX_1 — AUX channel port 1 (DisplayPort) |
| Pin produk 21 | AUX_2 — AUX channel port 2 (DisplayPort) |
| Pin produk 22 | HPD_IN — Hot plug detect input |
| Pin produk 23 | HPD_OUT — Hot plug detect output |
| Pin produk 24 | CC1_2 — Configuration Channel 1, port 2 |
| Pin produk 25 | CC2_2 — Configuration Channel 2, port 2 |
| Pin produk 26 | VBUS_2 — VBUS sense / power path, port 2 |
| Pin produk 27 | SRC_2 — Source path control, port 2 |
| Pin produk 28 | SNK_2 — Sink path control, port 2 |
| Pin produk 29 | DP_TXD0_P — DisplayPort high-speed TX lane 0 + |
| Pin produk 30 | DP_TXD0_N — DisplayPort high-speed TX lane 0 - |
| Pin produk 31 | DP_TXD1_P — DisplayPort high-speed TX lane 1 + |
| Pin produk 32 | DP_TXD1_N — DisplayPort high-speed TX lane 1 - |
| Pin produk 33 | DP_TXD2_P — DisplayPort high-speed TX lane 2 + |
| Pin produk 34 | DP_TXD2_N — DisplayPort high-speed TX lane 2 - |
| Pin produk 35 | DP_TXD3_P — DisplayPort high-speed TX lane 3 + |
| Pin produk 36 | DP_TXD3_N — DisplayPort high-speed TX lane 3 - |
| Pin produk 37 | DPEQ_SEL1 — DisplayPort signal-mux selector 1 |
| Pin produk 38 | DPEQ_SEL2 — DisplayPort signal-mux selector 2 |
| Pin produk 39 | GPI_1 — General purpose input 1 |
| Pin produk 40 | GPI_2 — General purpose input 2 |
| Pin produk 41 | GPI_3 — General purpose input 3 |
| Pin produk 42 | GPI_4 — General purpose input 4 |
| Pin produk 43 | GPO_3 — General purpose output 3 |
| Pin produk 44 | GPO_4 — General purpose output 4 |
| Pin produk 45 | VBUS_PROT — VBUS protection driver output |
| Pin produk 46 | THERM — Thermal monitor / shutdown pin |
| Pin produk 47 | BST1 — Bootstrap for high-side driver, port 1 |
| Pin produk 48 | BST2 — Bootstrap for high-side driver, port 2 |
| Pin produk 49 | HS_P1 — High-speed signal enable, port 1 |
| Pin produk 50 | HS_P2 — High-speed signal enable, port 2 |
| Pin produk 51 | V3P3V — Internal 3.3V LDO bypass |
| Pin produk 52 | V1P8V — Internal 1.8V LDO bypass |
| Pin produk 53 | VDD — Main supply input (5 V) |
| Pin produk 54 | GND — Ground |
| Pin produk 55 | GND — Ground |
| Pin produk 56 | GND — Ground |
Aplikasi Umum
TPS65988DDK cocok untuk 6 aplikasis: Dual-Port USB-C Docking Station, Thunderbolt 4 / USB4 Host Implementation, USB-C Monitor Input with KVM, Industrial PC with Dual USB-C, Gaming Console Dual-C Port, USB-C Power Bank with Source/Sink.
Dual-Port USB-C Docking Station
The TPS65988DDK is a natural fit for dual-port USB-C docking stations that must negotiate 20 V/5 A upstream while simultaneously exposing a downstream port to a connected peripheral. Its integrated 25 mOhm bidirectional switches handle the upstream VBUS power path without external load switches, saving roughly 4-6 discretes per port. With USB-IF TID# 1099 certification, designers can avoid lab re-certification when porting PD 3.0 to docks. The I2C/SPI host interface allows the dock MCU to policy-engineer power role swaps and DisplayPort stream assignment in real time.
Direkomendasikan
Thunderbolt 4 / USB4 Host Implementation
Host systems implementing Thunderbolt 4 or USB4 tunneling rely on the TPS65988DDK to manage dual Type-C ports at PD 3.0 with fast role swap and USB4 alternate-mode readiness. The integrated mux control signals steer the high-speed data lanes to the host CPU's retimer, while the integrated power switches carry 100 W per port to peripherals. The 56-VQFN 7x7 mm footprint suits compact mobile workstation layouts, and I2C host control enables platform firmware (BIOS/EC) to remap roles between USB4 and legacy modes.
Direkomendasikan
USB-C Monitor Input with KVM
USB-C monitors that accept 90-100 W input and provide downstream USB hub/KVM channels benefit from the TPS65988DDK's dual-port capability: upstream Type-C for power and video, downstream Type-C for peripherals. The 25 mOhm switches support 5 A continuous charging while DisplayPort alternate-mode muxing routes the video to the panel's scalar. Fast role swap ensures the monitor remains a sink even if the host releases source role, satisfying PD 3.0 continuity requirements.
Direkomendasikan
Industrial PC with Dual USB-C
Industrial PCs and HMIs requiring two USB-C ports find the TPS65988DDK ideal: PD 3.0 (USB-IF TID# 1099), dual-port mux control, and wide -40C to +85C operating range cover factory-floor environments. The integrated protection (OVP/OCP/OTP/RCP) on each VBUS path simplifies safety documentation for IEC 61131-2 compliance. GPIO outputs can drive status LEDs and external DC/DC enables for downstream peripherals.
Direkomendasikan
Gaming Console Dual-C Port
Modern gaming consoles offering dual USB-C for power delivery to controllers and VR headsets can leverage the TPS65988DDK as the controller hub. The dual-port protocol engine assigns source or sink roles on the fly, while the 25 mOhm switches handle VR-headset 60-90 W charging without a separate load switch. DisplayPort alt-mode passthrough supports VR video when wired to a compatible headset.
Direkomendasikan
USB-C Power Bank with Source/Sink
Battery-equipped devices such as USB-C power banks and portable hubs use the TPS65988DDK for bidirectional PD operation, where one port can sink to charge the internal battery while another port sources to a laptop. Fast role swap lets the bank instantly invert source/sink roles when the upstream cable reverses direction, and the integrated switches reduce BOM cost on each port by $0.20-0.30 USD versus discrete load switches.
Direkomendasikan
Ringkasan Produk Direkomendasikan
Data referensi engineering untuk TPS65988DDK — pembandingan, panduan desain, dan informasi konformitas.
Panduan Pemilihan
Pembandingan dengan Alternatif
| Parameter Umum | Produk Ini | TPS65988DHRSHR | TPS65988DKRSHR |
|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 56-VQFN (7x7 mm) | 56-VQFN (7x7 mm) - same | 56-VQFN (7x7 mm) - same |
| Number of Type-C Ports | 2 | 2 | 2 |
| USB PD Version | PD 3.0 | PD 3.0 | PD 3.0 (USB4/TBT4 tuned) |
| USB-IF Certification | Yes (TID# 1099) | Yes (TID# 1099) | Yes (TID# 1099) |
| Maximum VBUS Current | 5 A per port | 5 A per port | 5 A per port |
| Integrated Switch Rds(on) | 25 mOhm | 25 mOhm | 25 mOhm |
| Alternate Modes | DisplayPort, USB4 | DisplayPort, USB4 | DisplayPort, USB4 (USB4 optimized) |
Diferensiator Kunci
- Native dual-port PD 3.0 with integrated 25 mOhm switches (vsTPS65987DDK)
- USB-IF PD 3.0 certified (TID# 1099) (vsTPS65988DKRSHR)
- Wide -40C to +85C industrial operating range (vsTPS65988DHRSHR)
Catatan Desain
Route CC1/CC2 lines to the Type-C connector with 0.5 mm differential-style traces and a 5.1 kOhm pull-down (sink) or pull-up (source) at the CC pins - this sets the default USB-C role advertised during connect, and the TPS65988DDK overrides the default only after PD negotiation completes. Always keep CC traces short (<10 mm) and away from high-speed DP/USB4 lanes to avoid CC crosstalk.
At 20 V/5 A continuous the integrated power switches dissipate up to 1.25 W per port (I^2 * R = 25 * 0.025). Estimated: with the VQFN 56-pin thermal pad on a 2 oz 1 oz copper pour of roughly 1 cm^2 total, theta_JA is in the 25-30 C/W range, yielding a 30-40 C rise. For >85 C ambient operation or sustained 5 A loads, expand copper to a 4 cm^2 pour or add thermal vias to the bottom layer.
Do not omit the external EEPROM - the TPS65988DDK requires a configuration image for port roles, GPIO behavior, and policy engine rules. Default boot mode fails without a valid image. Also: keep VBUS bulk capacitance below 100 uF per port to satisfy USB PD inrush current limits; exceeding this triggers SourceCap negotiation errors. Use TI's TPS65988 configuration tool to generate the EEPROM HEX before layout finalization.
Place the external 5 V LDO and input bulk caps near pin 53 (VDD). Keep the I2C pull-ups on the host interface (pins 9-10) at 4.7 kOhm when the host runs at 400 kHz Fast Mode. DisplayPort aux lines (pins 20-23) must be length-matched to within 50 mil and routed on the same layer to maintain AUX timing during alt-mode entry.
Informasi Konformitas
USB-IF certified for PD 3.0 under TID# 1099. RoHS and REACH compliant per TI product page. Commercial grade - not AEC-Q100; for automotive use choose TPS65988-Q1 family.
