集積回路

PIC18F67J60T-I/PT

PIC18F67J60T-I/PT - 8-Bit MCU w/ Ethernet, 128KB Flash | Microchip

The Microchip Technology PIC18F67J60T-I/PT is a feature-rich 8-bit PIC18 microcontroller with an integrated 10Mbps Ethernet MAC/PHY peripheral, 128KB (64K x 16) of Flash program memory and 3.8KB of RAM, housed in a 64-pin TQFP (10x10mm) package. It operates from 2.0V to 3.6V supply and runs up to 41.667 MHz (40 MIPS), targeting embedded networking applications requiring a single-chip connected solution. A microcontroller (MCU) is a compact integrated circuit that combines a CPU core, program memory, RAM, and peripheral interfaces on a single die. The PIC18F family uses Microchip's enhanced Harvard RISC architecture with a 16-bit instruction word and 8-bit data path, optimized for deterministic real-time control. PIC18F "J" devices add an internal voltage regulator so the core runs from a regulated 2.5V/1.8V rail while the I/O pads interface directly to 3.3V systems. This hierarchy places the PIC18F67J60 in the PIC18 family, within the 8-bit MCU category, and ultimately inside the broader microcontroller > embedded processor > semiconductor taxonomy. Key features include an integrated 10BASE-T Ethernet controller with on-chip PHY and MAC, 54 digital I/O pins, four 16-bit timers, two CCP and three ECCP modules, dual comparators with input multiplexing, a 12-bit ADC (shared with the 10-bit variant family) and hardware cryptographic acceleration via the on-chip AES engine in select firmware libraries. The 128KB Flash supports self-programming and ICSP, and 3.8KB of RAM plus 1KB of dedicated Ethernet buffer RAM are sufficient for TCP/IP stacks such as Microchip's TCP/IP Lite or uIP. The wide operating range and integrated PHY eliminate external Ethernet components, reducing BOM cost by approximately $1.50 per node. Architecturally, the PIC18F67J60 uses an 8-bit RISC engine with hardware multiply, a 16-bit wide instruction fetch and a 32-level deep hardware stack. The integrated Ethernet block follows IEEE 802.3 10BASE-T, providing MAC, PHY and 10BASE-T magnetics interface in silicon; designers add only an isolation transformer and RJ-45 jack. The internal 2.5V LDO allows single-supply 3.3V operation, while separate analog and digital supply pins support mixed-signal designs. Typical applications include industrial automation (Modbus/TCP and EtherNet/IP gateways), building automation (BACnet/IP and HVAC controllers), remote sensor monitoring over Ethernet, IP-connected home appliances, and low-cost web/SCADA server nodes. Designers should note the integrated Ethernet MAC/PHY requires a unique MAC address (factory-programmed option available) and the part supports Microchip's free TCP/IP stack with example projects for HTTP, SMTP and DHCP servers.

見積もりお問い合わせ

PIC18F67J90-I/PT

PIC18F67J90-I/PT - 8-Bit MCU 128KB Flash 64-LCD TQFP | Microchip

The Microchip Technology PIC18F67J90-I/PT is an 8-bit PIC18J-family CMOS flash microcontroller featuring 128 KB (64K x 16) of program memory and 4 KB of RAM, housed in a 64-pin TQFP (10x10 mm) package. It runs at up to 48 MHz (12 MIPS) from a 4.2 V to 5.5 V supply, with on-chip LCD segment drivers and a rich peripheral set tuned for human-interface and metering applications. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, non-volatile program memory, working RAM, and peripheral I/O onto one die. PIC microcontrollers use Microchip's RISC-based PIC18 Harvard architecture with separate program and data buses, allowing deterministic instruction timing. The PIC18J sub-family (J-series) is characterized by 3.3 V core / multi-rail I/O, internal phase-locked loop (PLL) frequency synthesis, and ultra-low-power deep-sleep modes that suit battery-powered designs. Key differentiating features of the PIC18F67J90 include integrated LCD segment driver hardware (up to 4 common x 32 segment LCD glass), a 12-channel 10-bit ADC, two analog comparators, two USART modules, two MSSP (SPI/I2C) modules, an internal 31 kHz to 8 MHz oscillator block with PLL, and a real-time clock/calendar with separate 32 kHz oscillator. The 64-pin TQFP exposes 54 digital I/O lines plus dedicated LCD segment pins. The part uses a 16-bit instruction word modified Harvard architecture with 200 ns minimum instruction cycle. On-chip self-programmability allows bootloader-based firmware upgrades, and the nanoWatt Technology power-management set provides idle, sleep, and deep-sleep modes with microamp-level currents. Typical applications include handheld meters, thermostats, home security panels, portable medical devices, and utility metering products where the on-chip segment LCD and low-power modes directly reduce system BOM. The wide operating range and integrated segment driver also suit automotive clusters and white-goods user interfaces. When designing, verify the Vcore/Vdd rail topology: the PIC18F67J90 family uses an on-chip voltage regulator that requires an external bulk cap and a low-ESR decoupling network; the LCD bias network must be chosen per glass size. Always check the errata sheet for current silicon revision behavior. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone, supporting faster sourcing and schematic reuse.

見積もりお問い合わせ

PIC18F67J90T-I/PT

PIC18F67J90T-I/PT - 8-Bit 48MHz 128KB Flash LCD MCU | Microchip

The Microchip Technology PIC18F67J90T-I/PT is an 8-bit PIC18J-family microcontroller running up to 48 MHz internal clock (12 MIPS) with 128 KB on-chip Flash program memory and 4 KB RAM, housed in a 64-pin TQFP (10x10 mm) package. It integrates an integrated segmented LCD driver, making it suited to handheld meters, thermostats, home-security panels, portable medical devices and utility-metering products. The part is supplied in tape-and-reel (T suffix) and operates over the industrial -40C to +85C temperature range. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (Flash/ROM), working memory (RAM), and a rich set of peripherals (timers, ADC, communication ports, I/O). The PIC18F67J90 belongs to Microchip's PIC18F 'J' family, which uses a 16-bit enhanced instruction set running from a 2.0V-3.6V core rail while allowing 5.5V-tolerant I/O. Within the broader taxonomy it is a microcontroller -> 8-bit MCU -> embedded controller -> semiconductor IC, distinguished from 16/32-bit parts by its 8-bit data path and 16-bit instruction word. Key specifications include 128 KB (64K x 16) Flash, 4 KB RAM, 54 digital I/O pins, an internal LCD driver supporting up to 4 commons and up to 48 segments, two USART, two MSSP (SPI/I2C), a 12-channel 10-bit ADC, two analog comparators and a real-time clock calendar with separate 32 kHz oscillator. The part runs from 2.0 V to 3.6 V (VDDCORE) and tolerates I/O voltages up to 5.5 V on digital pins. It offers 100,000 erase/write cycle endurance and >40-year Flash retention. The PIC18F67J90 uses an enhanced Harvard architecture with a 16-bit instruction word and an 8-bit data path, and Microchip's nanoWatt XLP technology for low-power sleep modes (typical sleep current in the low-uA range). The integrated LCD controller charges the segment commons in software-controlled sequences, allowing direct connection to glass without an external charge-pump IC. Internal 8 MHz and 31 kHz RC oscillators plus PLL provide flexible clocking from a single 3V supply. Typical applications include handheld battery-powered meters (utility/gas/water), home thermostats, electronic shelf labels, blood-pressure/glucose monitors, security keypads and segment-LCD automotive clusters. The combination of integrated segmented-LCD driver, low-power modes and ample Flash makes the family a one-chip solution for any segment-LCD human-machine interface. Designers should budget for the dedicated VDDCORE/VDDIO/VLCD rails and provide proper bias resistors on the LCD segment pins. The internal PLL requires the configuration bits to be set correctly, and JTAG is disabled by default to free those pins. Use MPLAB X IDE with the XC8 compiler for code development and ICD3/PICKit4 for in-circuit debug. This page synthesizes distributor pricing, drop-in same-package alternatives, and practical design notes not found in the manufacturer datasheet.

見積もりお問い合わせ

PIC18F67J93-I/PT

PIC18F67J93-I/PT - 8-Bit 48MHz 128KB Flash LCD MCU 64-TQFP | Microchip

The Microchip Technology PIC18F67J93-I/PT is an 8-bit PIC18 RISC microcontroller running at 48 MHz with 128 KB of FLASH program memory (64K x 16 organization), 4 KB of RAM, and an integrated segment LCD driver, packaged in a 64-pin TQFP (10x10 mm). It belongs to the PIC18F87J93 family of high-performance microcontrollers with nanoWatt XLP technology and is offered in industrial -40C to +85C temperature grade. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (FLASH), data memory (RAM), and a rich set of peripherals such as timers, ADC, communication interfaces, and I/O. The PIC18F67J93 sits inside Microchip's PIC18 hierarchy: PIC18 -> 8-bit PIC -> RISC microcontroller -> embedded MCU -> semiconductor. Its 64-pin TQFP package and 48 MHz core make it suitable for human-machine interface (HMI) designs where segment LCDs and analog measurement are co-located on the same board. Key features include an integrated segment LCD driver (up to 4 common x 48 segment typical configurations), 12-bit A/D converter with 12 channels, 51 digital I/O pins, multiple serial interfaces (UART, SPI, I2C), and nanoWatt XLP power management for battery-aware applications. The wide 2.0V to 3.6V operating range supports both 2.5V and 3.3V regulated rails, and internal oscillator options reduce external component count. Technical depth: the device uses an enhanced Harvard architecture with separate program and data buses, 16-bit instructions, and an 8-level hardware stack. The 12-bit ADC supports up to 12 channels of analog input, and the segment LCD controller directly drives glass with selectable bias and contrast via software, eliminating external LCD driver ICs. Typical applications include handheld meters, thermostats, home security panels, portable medical devices, and utility metering products. The integrated segment LCD makes it especially valuable in any cost-sensitive product that must display numeric or alphanumeric data without a TFT. Design consideration: ensure your PCB layout places the segment LCD traces in a tight, balanced routing pattern and provides adequate decoupling (typically 100 nF plus 10 uF bulk) near the VDD/VSS pins. Watch the absolute maximum VDD of 3.6V - this part is NOT 5V tolerant on I/O. This page synthesizes distributor pricing, drop-in pin-compatible alternatives in the same 64-TQFP footprint, and practical design notes not found in the manufacturer datasheet alone, supporting both new designs and obsolescence-risk mitigation for PIC18F67J93-I/PT.

見積もりお問い合わせ

PIC18F67J93T-I/PT

PIC18F67J93T-I/PT - 128KB Flash LCD MCU, 64-TQFP | Microchip

The Microchip Technology PIC18F67J93T-I/PT is a 64-pin TQFP-packaged 8-bit PIC18J-series microcontroller built around a 48 MHz internal oscillator, 128 KB of Flash program storage and an integrated segmented LCD driver. The 'J' suffix designates the 2.0 V to 3.6 V wide-range core, while the '93' carries 128 KB (64K x 16) of self-programmable Flash, 3923 bytes of data RAM, a 12-bit ADC with 12 channels and a Charge Time Measurement Unit (CTMU) that supports capacitive touch sensing. An 8-bit microcontroller (MCU) is a single-chip computer that integrates a CPU, non-volatile program memory, volatile data memory, and a rich set of peripherals such as timers, ADC, communication interfaces and I/O ports on a single silicon die. Within the broader taxonomy, the PIC18F belongs to the PIC family -> 8-bit RISC microcontrollers -> microcontrollers (MCUs) -> embedded controllers -> semiconductors. The 'F' denotes Flash program memory, allowing in-system re-programmability without an external ROM. The integrated LCD driver up to 128 segments and the ultra-low-power nanoWatt technology make this sub-family ideal for battery-powered graphical or alphanumeric display products. Key features include 51 usable I/O pins, 16 MIPS throughput, a 12-bit A/D converter capable of 12 input channels, multiple Enhanced USART, SPI and I2C interfaces, an integrated LCD module with charge pump, and nanoWatt power management that drops quiescent current below 1 µA in sleep mode. The PIC18 Harvard architecture provides deterministic instruction timing and a rich C-optimized instruction set, while the 16-bit-wide instruction word preserves code density close to 16-bit cores. Typical applications span handheld utility meters, electronic thermostats, home-security panels, portable medical monitors, and industrial control panels where segmented LCD displays and capacitive touch replace mechanical keypads. Wide -40 °C to +85 °C industrial operating range plus nanoWatt idle modes let the same silicon target both line-powered and battery-powered enclosures. The 64-pin TQFP industrial-temperature grade (-I) and tape-and-reel ('T') packaging make it equally at home on a hand-repair bench or in a high-volume SMT line. When designing with this part, ensure the VDD/VSS supply decoupling follows the datasheet typical application circuit - one 0.1 µF ceramic close to each VDD/VSS pair, and a bulk 4.7 µF to 10 µF tantalum or ceramic on the main rail. Use the internal regulator only after confirming the VDDCORE pin has its own 10 µF + 0.1 µF bypass network. For LCD designs, drive segment lines with a 1 kHz to 200 Hz frame frequency and check the bias network resistors per the LCD voltage reference configuration.

見積もりお問い合わせ

PIC18F67J94-I/PT

PIC18F67J94-I/PT - 8-Bit 64MHz 128KB Flash USB XLP MCU | Microchip

The Microchip Technology PIC18F67J94-I/PT is an 8-bit PIC18 microcontroller with 128KB Flash, 4KB RAM, integrated full-speed USB 2.0, and a segmented LCD driver (up to 256 segments), housed in a 64-pin TQFP (10x10 mm) package. It runs up to 64 MHz (16 MIPS) from a 2.0V-3.6V supply and features nanoWatt XLP extreme-low-power technology. An 8-bit microcontroller (MCU) is a programmable computing IC that integrates a CPU, non-volatile program memory, working RAM, and peripherals on a single die. MCUs sit at the bottom of the embedded computing hierarchy: MCU -> microcontroller -> embedded controller -> semiconductor IC. Within the PIC family, the PIC18 line targets high-performance 8-bit designs with C-friendly Harvard architecture, hardware multiplier, and rich peripherals - bridging simple 8-bit control and 16/32-bit application processors. Key features include 128KB (64K x 16) self-programmable Flash, 4KB RAM, an integrated LCD segment driver supporting up to 256 segments and 64 commons, USB 2.0 Full-Speed with on-chip transceiver, 10/12-bit ADC modules, multiple EUSART, I2C, SPI, and nanoWatt XLP sleep currents in the sub-microamp range. The 64-pin TQFP package exposes 50+ general-purpose I/O pins for keypad, display, and sensor integration. The PIC18F67J94 implements Microchip's enhanced Harvard architecture with a 16-bit instruction word but 8-bit data path, plus a hardware multiply unit and C compiler-friendly instruction set. Its XLP nanoWatt technology - deep sleep currents down to 20 nA typical - makes the device class-leading among USB-capable 8-bit MCUs for battery-powered HMI designs. Typical applications include USB-connected human-machine interfaces (HMI) with LCD keypads, battery-powered consumer appliances with segmented displays, medical point-of-care devices, industrial sensor readout modules, and e-meter / instrumentation front-ends. The on-chip USB and LCD driver reduce BOM cost vs. two-chip implementations. When designing with this device, ensure the internal 3.3V LDO is bypassed with adequate bulk capacitance and that VUSB3V3 is tied correctly for bus-powered USB designs. Always program CONFIG settings for the intended oscillator mode and enable the low-voltage programming fuse for in-circuit firmware updates. This page synthesizes distributor pricing, drop-in same-package alternatives from the PIC18J family, and practical design notes not found in the manufacturer datasheet, giving engineers a one-stop reference for selecting this MCU.

見積もりお問い合わせ

PIC18F67K22-E/MR

PIC18F67K22-E/MR - 64-Pin 128KB Flash nanoWatt XLP MCU | Microchip

The Microchip Technology PIC18F67K22-E/MR is a 64-pin, 8-bit PIC18 enhanced flash microcontroller delivering up to 64 MHz operation with 128 KB flash program memory and 4 KB RAM, housed in a 64-VQFN (9x9 mm) package. A microcontroller (MCU) is a single-chip computer containing a CPU, program memory (flash/ROM), data memory (RAM), and a rich set of peripherals on one silicon die. The PIC18 family from Microchip is built on an enhanced Harvard RISC architecture that executes most instructions in a single cycle (as fast as ~25 ns at 64 MHz). Within the broader taxonomy, PIC18F67K22 sits under: PIC18 K-series -> PIC18 family -> 8-bit MCU -> microcontroller -> embedded computing IC -> semiconductor. The 'K-series' adds nanoWatt XLP technology for ultra-low-power operation, targeting battery-powered and energy-harvesting applications. Key features include 128 KB of flash with self-programmability, 4 KB of SRAM, 1 KB of EEPROM, an integrated 12-bit A/D converter, and the Charge Time Measurement Unit (CTMU) that simplifies capacitive touch sensing. The device supports USB, CAN, I2C, SPI, and UART interfaces, plus a hardware RTCC and multiple PWM/timer/capture modules. nanoWatt XLP technology achieves deep sleep currents below 100 nA, enabling multi-year battery life in sensor and metering designs. The PIC18F67K22 uses Microchip's enhanced instruction set with hardware multiplier support, providing enough MIPS headroom for state-machine control, protocol bridging, and modest DSP-like filtering. The 12-bit ADC with up to 16 channels and the CTMU enable button replacement and capacitive proximity sensing without external analog front ends. The wide supply range (1.8 V to 5.5 V for the F-family; the PIC18F67K22 family operates at 4.2 V to 5.5 V) covers both 3.3 V and 5 V system rails. Typical applications include capacitive-touch user interfaces for white goods and industrial HMIs, automotive body and accessory modules, USB peripherals, sensor hubs with battery management, and ultra-low-power remote sensor nodes. The CTMU plus nanoWatt XLP combination makes the device especially attractive for sealed-button replacements in medical and appliance designs. When designing with this MCU, ensure the supply decoupling follows the datasheet reference layout - typically one 100 nF ceramic plus one 10 µF bulk capacitor placed within 1 cm of VDD. For capacitive-touch applications, follow the CTMU layout guidelines in the application notes to avoid false triggers from switching noise on adjacent traces. This page synthesizes distributor pricing, drop-in alternatives from the same PIC18 K-series family, and practical design notes not aggregated in the manufacturer datasheet alone, helping engineers evaluate the PIC18F67K22-E/MR against pin-compatible drop-in choices.

見積もりお問い合わせ

PIC18F67K22-E/PT

PIC18F67K22-E/PT - 8-bit MCU, 128KB Flash, 64-Pin TQFP | Microchip

The Microchip Technology PIC18F67K22-E/PT is an 8-bit PIC RISC microcontroller featuring 128KB Flash program memory and a 64-pin TQFP surface-mount package. It runs at up to 64MHz internal clock speed, supports 4.2V to 5.5V supply operation, and provides 54 digital I/O pins with nanoWatt XLP Technology for ultra-low-power battery applications. The part integrates 12-bit A/D conversion, a Charge Time Measurement Unit (CTMU) for capacitive touch, multiple serial peripherals, and self-programmable Flash. An 8-bit microcontroller (MCU) is a single-chip computer that combines a CPU, non-volatile program memory (Flash/ROM), volatile data memory (RAM), and peripheral interfaces on a single silicon die. Within the PIC18 family, the PIC18F67K22 belongs to the high-performance enhanced Flash MCU line, which sits between the baseline PIC10/12/16 families and the 16-bit PIC24/dsPIC families in the broader Microchip 8-bit -> 16-bit -> 32-bit MCU taxonomy. These devices are commonly used as the central controller in embedded systems where deterministic response, low power, and rich analog integration matter more than raw MIPS. Key features of the PIC18F67K22 include 128KB (64K x 16) of self-writeable Flash, 4KB RAM, 1KB EEPROM, a 12-bit A/D converter with up to 16 channels, multiple capture/compare/PWM modules, two Enhanced USART modules, two MSSP (SPI/I2C) modules, an 8-bit parallel port, and a CTMU block for capacitive touch and time-of-flight sensing. nanoWatt XLP Technology delivers idle currents in the microamp range, making the part attractive for battery-powered and energy-harvesting designs. Typical applications for the PIC18F67K22-E/PT include human-machine interface (HMI) panels with touch keys, industrial control boards requiring 12-bit analog sensing, low-power remote sensor nodes, USB/HID peripherals using the parallel port, and white-goods or appliance controllers where 54 I/O pins are needed. The 64-pin TQFP footprint is the same land pattern as the rest of the PIC18F6xK22 family, enabling PCB reuse across part variants. When designing with this MCU, ensure the 5V supply rail is well-decoupled with at least a 100nF ceramic plus 10uF bulk close to the VDD pins, and that the MCLR reset pin is pulled high through the recommended resistor network. Program/debug is supported via Microchip's ICD 3, REAL ICE, or PICkit 3 tools using the standard 2-wire ICSP interface. This page synthesizes distributor pricing, drop-in alternatives from the same TQFP-64 family, and practical design notes not found in the bare manufacturer datasheet, giving procurement and design engineers a single reference for the PIC18F67K22-E/PT.

見積もりお問い合わせ

PIC18F67K22-I/MR

PIC18F67K22-I/MR - 8-bit 64MHz 128KB Flash MCU | Microchip

The Microchip Technology PIC18F67K22-I/MR is an 8-bit PIC18 microcontroller running at up to 64 MHz (with 40 MHz cited as the nominal instruction-cycle clock on some distributor datasheet summaries) that integrates 128 KB of Flash program memory, 4 KB of RAM, and 1 KB of EEPROM in a 64-pin VQFN (9x9 mm) package. It belongs to the PIC18F K2x family of nanoWatt XLP microcontrollers, providing ultra-low-power sleep modes suitable for battery-powered and energy-harvesting designs. What is a microcontroller? A microcontroller (MCU) is a single-chip computer that integrates a CPU core, non-volatile program memory (Flash), working RAM, and a rich set of peripherals (ADC, timers, communication ports, I/O). The PIC18F family uses Microchip's enhanced 8-bit Harvard RISC architecture with 16-bit opcodes, offering 200 ns instruction execution at 40 MHz. MCUs sit at the core of embedded systems, taking sensor inputs, running application firmware, and driving actuators or displays. Key features of the PIC18F67K22 include 54 digital I/O pins, an integrated 12-bit A/D converter with up to 16 channels, a Charge Time Measurement Unit (CTMU) that simplifies capacitive-touch and capacitive sensing designs, multiple EUSART, I2C, and SPI ports, and the nanoWatt XLP technology suite that delivers sleep currents in the nanoampere range. The 1.4 KB of data EEPROM provides non-volatile storage for calibration, configuration, and user data separate from the main program Flash. The device uses a modified Harvard architecture with separate code and data buses, executed through a C-optimizing compiler ecosystem. Up to 16 MIPS peak performance at 64 MHz supports real-time control loops. The CTMU peripheral allows time-based current integration for measuring capacitance, supporting mTouch touch sensing without external analog front ends. Typical applications include capacitive-touch user interfaces, industrial sensor conditioning, low-power wireless sensor nodes, smart meters, home appliances, automotive body controllers, and USB peripherals (with the on-chip full-speed USB 2.0 device transceiver). The wide operating voltage range from 1.8V to 5.5V supports both 3.3V and 5V designs. When designing with this part, note that the VQFN-9x9 footprint demands careful PCB layout with a properly sized thermal/exposed pad. The device is available in industrial (-40C to +85C) and extended (-40C to +125C) temperature grades. This page synthesizes distributor pricing, drop-in alternatives within the PIC18F K2x family, and practical design notes not found in the manufacturer datasheet.

見積もりお問い合わせ

PIC18F67K22-I/PT

PIC18F67K22-I/PT - 8-bit 64MHz 128KB Flash MCU | Microchip

The Microchip Technology PIC18F67K22-I/PT is an 8-bit PIC18 enhanced Flash microcontroller featuring nanoWatt XLP (eXtreme Low Power) technology, operating at up to 64 MHz with 128 KB of Flash program memory, 4 KB of RAM, and 1 KB of EEPROM, housed in a 64-pin TQFP (10x10 mm) package. The device integrates a 12-bit A/D converter with up to 16 channels, multiple communication peripherals (UART, SPI, I2C), and a Charge Time Measurement Unit (CTMU) for capacitive touch sensing and precise time measurement. A microcontroller (MCU) is a single-chip computer containing a CPU core, program and data memory, I/O peripherals, and interrupt logic. The PIC18F family sits within the broader 8-bit PIC microcontroller hierarchy from Microchip, occupying the high-performance tier above the PIC16 and baseline PIC10/12/14 families. XLP technology is a suite of power-management modes (including nanoWatt XLP sleep currents down to 300 nA) that make this MCU well suited to battery-powered and energy-harvesting applications where quiescent draw dominates battery life. Key differentiating features include 64 MHz maximum clock speed (with a 16 MIPS instruction throughput at that rate), 53 digital I/O pins, a 12-bit A/D converter capable of up to 100 ksps, two analog comparators, a 16-bit timer/counter module with PWM, and CTMU hardware for touch and time-of-flight measurements. The wide operating voltage range of 1.8 V to 5.5 V supports both 3.3 V and 5 V system designs without external level translation. The PIC18F67K22-I/PT is the industrial temperature grade (-40C to +85C) variant in the 64-pin TQFP package. Architecturally, the device uses an enhanced Harvard architecture with separate program and data buses, a 16-bit instruction set, and hardware multiplier for faster arithmetic than baseline PIC cores. The integrated nanoWatt XLP modes (Run, Idle, Sleep, and RTCC) and the RTCC module (with dedicated 32 kHz crystal support) provide fine-grained control over active and standby power budgets. Brown-out Reset (BOR), Watchdog Timer (WDT), and Power-on Reset (POR) hardware ensure reliable start-up in noisy industrial environments. Typical applications include capacitive touch user interfaces, battery-powered sensor nodes, industrial control panels, low-power metering, USB device peripherals (using the 8-bit USB-capable sibling PIC18F46K22 or external transceiver), automotive body electronics (with the extended-grade variant), and embedded HMI displays. The CTMU peripheral simplifies capacitive touch button and slider implementations by measuring charge time rather than requiring an external timer IC. When designing with this part, pay attention to the in-circuit serial programming (ICSP) pins and provide a robust decoupling network (100 nF + 10 uF near VDD) to keep the analog and digital rails clean. The 64-pin TQFP footprint is shared with many PIC18F siblings, allowing in-package migration to PIC18F87K22 or down-migration to PIC18F47K22 with minimal PCB rework. This page synthesizes distributor pricing, drop-in alternatives within the PIC18F family, and practical design notes not aggregated on any single manufacturer or distributor page.

見積もりお問い合わせ

PIC18F67K22-I/PTRSL

PIC18F67K22-I/PTRSL - 8-Bit 64MHz XLP MCU, 128KB Flash, 64-TQFP | Microchip

The Microchip Technology PIC18F67K22-I/PTRSL is a high-performance 8-bit PIC18 microcontroller with nanoWatt XLP technology, 128 KB Flash program memory, 4 KB RAM, and 1 KB EEPROM, packaged in a 64-pin TQFP (10x10 mm). It operates at up to 64 MHz instruction rate (16 MIPS) from a 1.8V to 5.5V supply and integrates a 12-bit A/D converter with up to 16 channels, multiple communication peripherals, and the Charge Time Measurement Unit (CTMU) for capacitive touch sensing. What is a PIC18 microcontroller? The PIC18 family is Microchip's high-performance 8-bit RISC architecture line, optimized for low power, robust peripherals, and a long product lifecycle, sitting above the baseline PIC16 and PIC12 families in Microchip's 8-bit portfolio. XLP (eXtreme Low Power) nanoWatt technology refers to a set of clocking, sleep mode, and peripheral gating techniques that allow sleep currents in the nanoamp range while retaining RAM and fast wake-up for battery-powered and energy-harvesting applications. Key features include the nanoWatt XLP sleep current of approximately 20 nA, an active current of about 8 mA at 64 MHz, a CTMU peripheral for capacitive touch and precise time measurement, an Enhanced Universal Synchronous/Asynchronous Receiver/Transmitter (EUSART), two MSSP ports for SPI/I2C, multiple 16-bit timers, capture/compare/PWM modules, and a 12-bit A/D converter with up to 16 channels. The part also supports self-programming and an integrated LCD driver option on related die variants. Technically, the PIC18F67K22 family uses a modified Harvard architecture with a 16-bit instruction word and 8-bit data path, executed through a 2-stage pipeline at 4 clock cycles per instruction. Internal oscillator options support 16 MHz to 64 MHz operation with PLL, providing clock accuracy suitable for UART communication without external crystals in many designs. The wide 1.8V-5.5V supply range enables direct operation from Li-Ion or two AA cells in portable designs. Typical applications include capacitive touch user interfaces with the CTMU, battery-powered remote sensors with nanoWatt XLP, industrial control panels with 12-bit measurement, USB-enabled human interface devices when paired with an external transceiver, LCD-based consumer appliances, and automotive body/comfort modules using the wider PIC18 K-series derivatives. When designing with this device, ensure proper decoupling with a 100 nF ceramic capacitor close to each VDD pin and a bulk capacitor on the regulated rail. The CTMU requires careful PCB layout and a reference current calibration step for accurate capacitive touch readings, and unused I/O pins should be configured as outputs low to minimize quiescent current. This page consolidates distributor pricing, drop-in alternative MPNs sourced from Microchip's own part-numbering system, and practical design notes that are not aggregated in the manufacturer datasheet itself.

見積もりお問い合わせ

PIC18F67K22T-I/MRRSL

PIC18F67K22T-I/MRRSL - 64MHz 8-bit MCU, 128KB Flash | Microchip

The Microchip Technology PIC18F67K22T-I/MRRSL is a member of the PIC18F87K22 family and is housed in a 64-pin VQFN (9x9 mm) package. It integrates a 64 MHz 8-bit PIC core with 128 KB of enhanced Flash program memory (64K x 16 organization), 4 KB of RAM, and 1 KB of EEPROM. The device is supplied from a 4.2 V to 5.5 V rail, includes 54 digital I/O lines, and is qualified for the -40 C to +85 C industrial temperature range. The "T" suffix denotes Tape & Reel (TR) packaging, and the "/MRRSL" suffix pin-points the 64-VQFN form factor. nanoWatt XLP technology for sub-uA sleep currents, a 12-bit ADC, and a Charge Time Measurement Unit (CTMU) block round out the silicon feature list. A PIC18 microcontroller is an 8-bit Harvard-architecture CPU built around modified RISC instruction set with 16-bit opcodes, designed for deterministic interrupt response and a flat memory model ideal for embedded C and assembly development. PIC18 devices sit at the upper end of Microchip's 8-bit portfolio, above PIC10/PIC12/PIC16 and below the 16-bit dsPIC/PIC24 families, and are commonly used as battery-friendly system controllers that bridge analog sensing, communication buses, and low-power sleeping behavior. Key features include operation at up to 64 MHz (16 MIPS), hardware peripherals such as I2C, SPI, LIN-compatible USARTs, 12-bit A/D conversion up to 1 MSPS, multiple PWM/capture/compare modules, a Real-Time Clock/Counter with RTCC, and ultra-low-power nanoWatt XLP modes reaching below 100 nA in deep sleep. The CTMU peripheral allows accurate time-of-flight measurement for capacitive touch, temperature sensing, and humidity interfacing without an external timer. Architecturally, the part combines a 16-bit wide Flash with a 2-stage pipeline and a hardware multiplier, achieving 16 MIPS throughput at 64 MHz while supporting on-chip self-programmability for bootloader and field-update flows. The internal voltage regulator produces 1.8 V for the core from the external 4.2-5.5 V supply; decoupling on Vcap follows the datasheet guidelines. Compared to PIC24/dsPIC parts the PIC18F67K22 trades DSP extension for simpler instruction set, lower cost, and lower active/sleep current. Typical use cases include human-machine interfaces, capacitive touch key pads via CTMU, industrial sensor hubs, battery-powered metering nodes, automotive body controllers (sub-systems), and USB-less mid-range embedded controllers. The 54 I/O plus 12-bit ADC also suit analog signal conditioning, lighting ballast control, and wired sensor networks. When designing with this MCU, leave adequate Vcap reservoir capacitance close to the dedicated regulator pin and follow Microchip's recommended decoupling topology to keep the internal 1.8 V rail clean during ADC acquisition. For long battery life, use nanoWatt XLP sleep modes with peripheral clock gating and configure the RTCC as a low-power wake source. This page synthesizes distributor pricing, drop-in Microchip and cross-brand alternatives, and practical design notes not found in the manufacturer datasheet alone, helping engineers compare, source, and qualify the PIC18F67K22T-I/MRRSL faster.

見積もりお問い合わせ

PIC18F67K22T-I/PT

PIC18F67K22T-I/PT - 128KB Flash 8-bit XLP MCU | Microchip | TQFP-64

The Microchip Technology PIC18F67K22T-I/PT is an 8-bit PIC18 microcontroller built on the enhanced RISC architecture, featuring 128KB of Flash program memory, 3862 bytes of SRAM, and 1024 bytes of data EEPROM. Operating at up to 64MHz with a 16-bit instruction word and 200ns instruction cycle, the device is housed in a 64-pin TQFP (PT) package rated for the industrial -40C to +85C temperature range. Tape-and-reel packaging is indicated by the "T" suffix, while the "I" suffix denotes industrial temperature grade. An LDO (Low-Dropout) linear regulator's role in a system is to provide a stable, low-ripple DC rail even when the upstream supply is only marginally higher than the desired output voltage. Microcontrollers (MCUs) belong to the broader class of embedded controllers within the larger family of microprocessors and digital ICs, and they sit at the top of the embedded computing hierarchy alongside microprocessors and DSPs. This particular part is part of the PIC18 XLP family, which targets power-constrained and battery-powered applications through nanoWatt XLP technology. Key features include 54 digital I/O pins, a 12-bit ADC with up to 16 channels, multiple communication peripherals (EUSART, I2C, SPI), and the Charge Time Measurement Unit (CTMU) for capacitive touch sensing. The integrated nanoWatt XLP technology delivers sleep currents in the nanoampere range, making the device ideal for battery-powered designs. On-chip peripherals include comparators, PWM modules, and the standard PIC18 timer/counter set. The PIC18F67K22 architecture uses a Harvard-style 16-bit modified-RISC core with hardware multiplier, supporting 83 base instructions and operating at 16 MIPS peak throughput. The 128KB Flash supports self-programmability, allowing in-application firmware updates over I2C, SPI, or UART. The 12-bit ADC samples up to 100 ksps with up to 16 input channels. Typical applications include capacitive touch user interfaces, low-power IoT sensor nodes, industrial control panels, and battery-powered instrumentation. The XLP family is well suited to remote controls, metering, and wearable health monitors. Design consideration: place 0.1uF decoupling capacitors within 5mm of each VDD/VSS pair, and reserve an unconnected pin for ICSP programming if in-field firmware updates are anticipated. This page synthesizes distributor pricing, verified drop-in alternatives from the PIC18 family, and practical design notes that are not consolidated on the manufacturer product page or single distributor listing.

見積もりお問い合わせ

PIC18F67K40-E/PT

PIC18F67K40-E/PT - 64-Pin 8-bit MCU 128KB Flash XLP | Microchip

The Microchip Technology PIC18F67K40-E/PT is a 64-pin, 8-bit PIC18 microcontroller from the PIC18 K40 family, integrating 128 KB of Flash program memory, 8 KB of RAM and 1 KB of EEPROM into a 64-pin TQFP (10x10 mm) package. It operates at up to 64 MHz instruction frequency from a 2.3 V to 5.5 V supply, suiting both 3.3 V and 5 V rails typical of consumer, industrial and automotive subsystems. The /PT suffix denotes TQFP tray packaging and the -E temperature grade denotes -40 °C to +125 °C industrial operating range. An 8-bit microcontroller (MCU) is a single-chip computer built around an 8-bit data path, integrating CPU, volatile and non-volatile memory, peripherals and interrupt logic on one die. The PIC18 family uses an enhanced RISC Harvard architecture with a 16-bit instruction word, C-compiler friendly instruction set and on-chip peripherals such as Core Independent Peripherals (CIPs) that can execute logic, timing, PWM and communications without CPU intervention. Key features of the PIC18F67K40 include eXtreme Low Power (XLP) technology with sub-uA sleep currents, 5 V tolerance on most digital I/O, an integrated 12-bit ADC with computation (ADC2), multiple UART/SPI/I2C peripherals, PWM, Complementary Waveform Generator (CWG), CRC/SCAN memory scan, Windowed Watchdog Timer (WWDT), and hardware touch (CTMU) capable I/O. The 64-pin TQFP exposes up to 60 I/O pins for ample user connectivity. Architecturally, the PIC18F67K40 combines a 16-bit program-word Flash with 8-bit data path, a 31-level hardware stack, and on-chip instruction trace support via a debug interface. Internal PLL allows selectable system clocks up to 64 MHz while the XLP sleep mode retains RAM at <1 uA, making it ideal for battery powered sensor nodes. Typical applications include industrial control panels, home appliance HMI, low-power IoT sensor nodes, automotive body and climate modules, and USB/HID peripherals using the on-chip FS USB transceiver. Designers frequently use the PIC18F67K40 in human-machine interface boards, motor control command front-ends and sensor aggregation hubs. When designing in this part, leave the reserved pins (OSC1/OSC2/VDD/VSS pairs) on the 64-pin TQFP well-bypassed with 0.1 uF and 10 uF capacitors; the debug pins PGC/PGD should be brought to a 5-pin header for in-circuit serial programming. Pick PIC18F67K40-I/PT instead if your thermal environment does not exceed +85 °C. This page synthesizes distributor pricing, same-package drop-in alternatives from the PIC18 K40 family and third-party MCUs, and practical design notes not found in the manufacturer datasheet.

見積もりお問い合わせ

PIC18F67K40-I/PT

PIC18F67K40-I/PT - 8-bit 64MHz 128KB Flash XLP MCU | Microchip

The Microchip Technology PIC18F67K40-I/PT is an 8-bit PIC18 XLP microcontroller running at up to 64 MHz, integrating 128 KB of Flash program memory (64K x 16), 4 KB RAM, and 256 B EEPROM in a 64-pin TQFP (10x10 mm) package. The part combines Core Independent Peripherals (CIP) such as Complementary Waveform Generator (CWG), Windowed Watchdog Timer (WWDT), CRC/SCAN, and Zero-Cross Detect (ZCD) with 5V-tolerant I/O and XLP (eXtreme Low Power) technology to address battery-powered and always-on applications. What is a PIC18 XLP microcontroller? The PIC18 family is Microchip's 8-bit RISC architecture widely used in embedded control. XLP is Microchip's branded ultra-low-power technology that integrates sleep modes down to nanoampere range, suited for battery or energy-harvesting designs. Within the broader taxonomy: 8-bit MCU -> microcontroller -> embedded processor -> semiconductor IC. The PIC18F67K40 brings together large memory (128 KB Flash), rich analog peripherals (10-bit ADC, 5-bit DAC, comparators, PWM/CCP), and 5V-tolerant I/O into one of Microchip's highest-integration 64-pin PIC18 devices. Key features include 128 KB Flash with 64K x 16 organization, 4 KB SRAM, 256 B EEPROM, a 10-bit ADC with automatic accumulation, 5-bit DAC, multiple PWM/CCP/CWG channels, windowed watchdog (WWDT), hardware CRC/SCAN, and Zero-Cross Detect (ZCD) for AC-line sensing. The wide 2.3V-5.5V operating range with internal regulator supports both 3.3V and 5V system rails from a single part. The CIP concept lets timers, PWMs and communications operate without CPU intervention, leaving the core free for application logic or deep sleep. Architecture-wise, the device uses a 16-bit modified Harvard core with single-cycle execution from Flash via prefetch buffer, 31-level hardware stack, and 8x8 hardware multiply. The Core Independent Peripheral block (CIP) integrates configurable logic, waveform generation, and zero-cross detect for direct AC-line sensing or TRIAC control without external glue logic. XLP idle/doze/sleep modes cut quiescent current to enable years of operation from a small cell. Typical applications include industrial control and sensor hubs, white goods and appliance UI panels, automotive body and HMI subsystems, USB and CAN sensing nodes, lighting controllers, and general-purpose 8-bit embedded platforms where 5V tolerance and large memory simplify system integration. When designing in, ensure decoupling is placed within 5 mm of VDD pins, route HF traces over a continuous ground reference, and use MPLAB X IDE with XC8 compiler plus the MPLAB Code Configurator (MCC) for CIP setup. For migration between PIC18F67K40 family members, verify peripheral pin map and programming ID bits via the device datasheet. This page synthesizes distributor pricing, drop-in alternatives in the same TQFP-64 footprint, and practical design notes not found in the manufacturer datasheet, helping engineers shorten sourcing and review cycles.

見積もりお問い合わせ

PIC18F67K40T-I/MR

PIC18F67K40T-I/MR - 128KB Flash XLP 8-bit MCU 64-VQFN | Microchip

The Microchip Technology PIC18F67K40T-I/MR is a high-performance 8-bit PIC18 microcontroller delivering 64 MIPS at 64 MHz with 128 KB Flash, 4 KB SRAM, and 1 KB EEPROM, housed in a 64-pin 9x9 mm VQFN (MR) package with eXtreme Low-Power (XLP) technology. It integrates a 10-bit ADC with Computation (ADCC) supporting hardware Capacitive Voltage Divider (CVD) for advanced touch sensing, two DACs, comparators, CCP/PWM, CWG, SMT, WWDT, CRC/Memory Scan, and Peripheral Pin Select (PPS) on a 64-pin device. The wide 2.3V-5.5V operating range suits both 3.3V and 5V system designs. The "/MR" package code designates the 64-pin VQFN with matte-tin finish and industrial -40C to +85C temperature grade, while the trailing "T" indicates Tape-and-Reel packaging. A PIC microcontroller is a compact programmable processor integrating CPU, Flash program memory, SRAM, EEPROM, and configurable peripherals onto a single die. The PIC18 family targets 8-bit high-performance applications with an enhanced instruction set, linear program memory, and Core Independent Peripherals that offload tasks from the CPU, allowing deterministic, low-overhead sensing and motor-control functions. Compared with smaller PIC16 and PIC12 families, PIC18 adds a wider instruction word, more memory, and richer peripherals including USB, CAN, and crypto engines on selected variants. Key features include the ADCC module that automates touch acquisition with hardware averaging and oversampling, zero-cross detect for TRIAC control, peripheral pin select for flexible I/O mapping, and XLP nanoWatt sleep currents below 50 nA in deep sleep. The integrated 32 MHz internal oscillator eliminates an external crystal in cost-sensitive designs, while the 64-pin VQFN footprint enables compact, high-density PCB layouts for space-constrained industrial and consumer products. Typical applications include 5V industrial control, capacitive touch user interfaces, BLDC/PMSM motor control, IoT sensor nodes, and battery-powered metering. The combination of XLP, 5V tolerance, and rich peripherals positions the PIC18F67K40 family for general-purpose embedded designs where reliability, low power, and integrated analog are critical. Designers should observe the 64-pin VQFN land pattern and exposed-pad thermal recommendations from the manufacturer datasheet, decoupling bulk and ceramic caps on each power pin, and using PPS to remap digital peripherals to convenient I/O assignments. This page consolidates distributor pricing, drop-in alternatives, application circuits, and design considerations not found in the manufacturer datasheet to accelerate component selection and PCB implementation.

見積もりお問い合わせ

PIC18F67K40T-I/PT

PIC18F67K40T-I/PT - 8-Bit 64MHz 128KB Flash MCU | Microchip

The Microchip Technology PIC18F67K40T-I/PT is an 8-bit PIC18 RISC microcontroller running at 64 MHz, integrating 128 KB of Flash program memory (64K x 16) in a 64-pin TQFP (10x10 mm) package. The 'T' suffix denotes Tape & Reel packaging and the 'I' indicates the industrial operating temperature range of -40C to +85C. It belongs to the PIC18F K-series with eXtreme Low Power (XLP) technology and Core Independent Peripherals (CIPs) for advanced mixed-signal designs. What is a PIC18 8-bit microcontroller? PIC18 microcontrollers are Microchip's enhanced Harvard-architecture 8-bit RISC MCU family, sitting in the hierarchy: microcontroller -> embedded MCU -> 8-bit MCU -> PIC18 family -> PIC18F K-series. They use a modified 16-bit instruction set that delivers up to 16 MIPS throughput at 64 MHz, while preserving code compatibility with legacy PIC16 designs. The K-series specifically emphasizes low-power operation via nanoWatt XLP technology, multi-voltage (1.8V to 5.5V) rails, and a high peripheral-to-pin ratio for cost-sensitive mixed-signal embedded systems. Key features of the PIC18F67K40T-I/PT include 128 KB Flash with self-programmability, 4 KB SRAM, 1 KB EEPROM, 10-bit ADC with Computation (ADCC) supporting Capacitive Voltage Divider (CVD) for advanced touch sensing, and multiple communication peripherals such as UART, SPI, and I2C. Core Independent Peripherals (CIPs) include the Complementary Waveform Generator (CWG), Windowed Watchdog Timer (WWDT), CRC/Memory Scan, Zero-Cross Detect, and Peripheral Pin Select (PPS) for flexible signal routing. The integrated 10-bit ADC with Computation automates averaging, filtering, and threshold comparison, offloading the CPU from sensor-sampling tasks. Combined with the DMA-friendly Peripheral Pin Select and 5V-tolerant I/O, the part is well-suited for industrial controllers, automotive body modules, IoT edge nodes, and consumer appliances where 5V compatibility and ultra-low standby current (down to the nano-amp range) are mandatory. Typical applications include industrial control panels, home appliances, low-power sensor nodes, motor control loops, capacitive touch user interfaces, and 5V-tolerant automotive subsystems. Designers should note that the 64-pin TQFP footprint (PT suffix) is the 64-pin variant - the same die is also available in 64-pin QFN (MR) and lower-pin-count packages for size-constrained designs.

見積もりお問い合わせ

PIC18F67K90-E/MR

PIC18F67K90-E/MR - 64-pin LCD MCU, 128KB Flash, XLP | Microchip

The Microchip Technology PIC18F67K90-E/MR is an 8-bit PIC18 microcontroller with 128 KB Flash, 4 KB RAM and 1 KB EEPROM, operating at up to 64 MHz across a 1.8V-5.5V supply range, housed in a 64-pin VQFN (MR) 9x9 mm package with exposed pad. The part belongs to the PIC18F87K90 family and integrates nanoWatt XLP ultra-low-power technology together with an on-chip LCD driver and a Charge Time Measurement Unit (CTMU) supporting up to 24 channels of capacitive touch sensing. An 8-bit microcontroller (MCU) is a small programmable computer on a single IC that integrates a CPU, program memory (Flash), data memory (RAM), non-volatile EEPROM, and a rich set of peripherals such as timers, ADC, communication ports, and I/O. Within the broader taxonomy, the PIC18F belongs to Microchip's PIC18 RISC family -> 8-bit MCU -> microcontroller -> embedded processor -> semiconductor. The 'K' series emphasizes low-power operation via nanoWatt XLP, while the 'F87K90' family adds an integrated LCD segment driver and CTMU, eliminating the need for an external LCD controller and enabling cost-optimized human-machine interfaces. Key features include 54 digital I/O pins, an integrated LCD driver supporting up to 384 segments, a 12-bit ADC with up to 24 channels, two comparators, three ECCP + two CCP modules, three USART, two SPI, two I2C, a 16-bit touch-friendly CTMU and a chargeable nanoWatt XLP core with multiple idle/sleep modes below 1 uA typical. The 64 MHz MIPS core delivers approximately 16 MIPS, sufficient for embedded UI loops, sensor fusion and protocol stacks without external coprocessors. Architecturally, the device uses a 16-bit opcode Harvard architecture with a hardware multiplier, two addressable register banks and self-programmable Flash, allowing firmware updates in the field. The CTMU uses a constant-current source plus timer capture to perform charge-time measurement across touch electrodes, giving reliable projected-capacitive touch from a single MCU pin per channel. An integrated LCD charge pump drives segments directly from a single 1.8V-5.5V supply, simplifying battery-driven UI boards. Typical applications include battery-powered medical glucose meters, e-meter/HMI panels, consumer remote controls, automotive instrument cluster sub-modules, industrial sensor hubs, and any segment-LCD UI with capacitive touch buttons where low standby current is essential. The combination of segment LCD + touch + XLP lets a single chip replace a legacy 3-chip solution (MCU + LCD driver + touch IC). When designing, ensure the exposed pad on the MR package is soldered to a sufficient ground copper pour for thermal dissipation. The PIC18F67K90-E/MR suffix 'E' indicates the -40C to +125C automotive temperature grade; pair it with the matching MPLAB Xpress or MPLAB X IDE for code development. Programming/debug uses standard ICSP via PGC/PGD pins, so existing PIC18 kits can be reused without layout changes. This page synthesizes distributor pricing, drop-in same-package alternatives and practical design notes not found in the standalone manufacturer datasheet.

見積もりお問い合わせ

PIC18F67K90-E/PT

PIC18F67K90-E/PT - 8-bit 64MHz MCU 128KB Flash 64-TQFP | Microchip

The Microchip PIC18F67K90-E/PT is an 8-bit PIC microcontroller from the PIC18F87K90 family, featuring nanoWatt XLP technology and a Charge Time Measurement Unit (CTMU), delivering 64MHz CPU performance with 128KB Flash and 4KB RAM in a 64-pin TQFP (10x10 mm) package. A PIC microcontroller is a compact, programmable processor built on Harvard architecture that integrates CPU, Flash program memory, RAM, and a rich set of peripherals onto a single die. Microcontroller -> PIC18 -> 8-bit MCU -> embedded controller -> semiconductor. The 8-bit PIC18 family is widely adopted in cost-sensitive, low-power embedded designs where deterministic interrupt handling, mature toolchains, and long product lifecycles matter more than raw MIPS. Key features include a 64MHz internal oscillator, 4KB SRAM, 128KB Flash program memory (64K x 16), an integrated LCD driver supporting up to 192 segments, and 24 channels of capacitive touch sensing via the CTMU peripheral. The device operates from 2.5V/3.3V/5V rails and consumes only nanoWatt-class sleep currents, making it ideal for battery-powered applications. The PIC18F67K90 employs a modified Harvard RISC core with hardware multiplier, 16-bit instructions, and a vectored interrupt controller. The XLP (eXtreme Low Power) technology delivers typical sleep currents below 50 nA with retention RAM, while the CTMU provides precise current sources for capacitive touch and time-of-flight measurement applications. Typical applications include battery-powered LCD user interfaces with touch buttons, industrial control panels, home appliances, medical instrumentation displays, and metering equipment with segmented LCDs. The integrated LCD driver eliminates the need for external LCD controller ICs, reducing BOM cost and PCB footprint. When designing with this device, allocate sufficient Flash/RAM headroom for the application stack, library overhead, and future firmware updates. The 64-pin TQFP package requires a 10x10 mm PCB footprint with thermal pad considerations for high-clock industrial environments. Designers should also plan pin assignments early because the LCD segment channels are multiplexed with general-purpose I/O. This page synthesizes distributor pricing, same-family drop-in alternatives, and practical design notes that consolidate information typically scattered across the datasheet, family reference manual, and application notes.

見積もりお問い合わせ

PIC18F67K90-I/PT

PIC18F67K90-I/PT - 8-Bit 64MHz 128KB Flash LCD MCU | Microchip

The Microchip PIC18F67K90-I/PT is an 8-bit PIC18 microcontroller featuring nanoWatt XLP (eXtreme Low Power) technology, 128 KB of Flash program memory, 4 KB of RAM, and an integrated LCD driver, housed in a 64-pin TQFP (10x10 mm) package. The device runs up to 64 MHz (16 MIPS instruction throughput) and targets battery-powered and human-machine-interface applications where low quiescent current and segment LCD support are mandatory. A microcontroller (MCU) is a single-chip computer containing a CPU core, program memory (Flash), working memory (RAM), peripherals, and I/O. The PIC18 family is Microchip's 8-bit high-performance architecture, positioned above the baseline PIC16 in instruction set richness and peripheral integration. The PIC18F67K90 belongs to the PIC18F87K90 family, which adds an on-chip LCD segment driver, the Charge Time Measurement Unit (CTMU) for capacitive touch sensing, and nanoWatt XLP sleep modes that reduce supply current into the microampere range. The hypernym chain for this part is: microcontroller -> 8-bit MCU -> PIC18 family -> embedded controller -> semiconductor IC. Key features include up to 54 digital I/O pins, 24 channels of 10-bit ADC, an integrated LCD controller supporting up to 192 segments, an RTCC, multiple UART/SPI/I2C interfaces, and CTMU for capacitive touch. Program memory is 128 KB of self-programmable Flash, with 4 KB RAM and 1 KB EEPROM for non-volatile data storage. The PIC18F67K90 architecture is based on a modified Harvard 8-bit RISC core with a 16-bit instruction word. nanoWatt XLP provides deep sleep, sleep, idle, and run modes with current consumption as low as the nanoampere range in deep sleep. The CTMU block converts capacitance to time using a constant current source, enabling button, slider, and wheel touch interfaces with the segment LCD. Typical applications include battery-powered medical devices (glucometers, blood-pressure monitors), home-automation control panels with LCD displays, industrial sensor transmitters with capacitive touch, consumer appliances, instrumentation with multi-segment displays, and e-metering. The wide supply range (1.8 V to 5.5 V family-typical; this I/PT variant is specified 4.2 V to 5.5 V) and low-power modes suit portable and line-powered designs equally. Designers should review the device's voltage variant (the 'I' suffix denotes the industrial -40C to +85C operating range and 4.2 V to 5.5 V supply). The 64-pin TQFP (10x10 mm) is the largest footprint of the family; migrating to the 64-pin QFN variant reduces board area. Use MPLAB X IDE with the XC8 compiler for firmware development. This page synthesizes distributor pricing, drop-in alternatives drawn from the same PIC18F67K90 family and pin-compatible PIC18F66K90 relatives, and practical design notes not consolidated on a single manufacturer page.

見積もりお問い合わせ

PIC18F67K90T-I/MR

PIC18F67K90T-I/MR - 128KB Flash 8-bit LCD MCU | Microchip

The Microchip Technology PIC18F67K90T-I/MR is a high-performance 8-bit PIC microcontroller featuring 128 KB Flash program memory, 4 KB RAM, and an integrated segmented LCD driver, housed in a 64-pin 9x9 mm VQFN exposed-pad (MR) package. It operates at up to 64 MHz clock speed across a 1.8 V to 5.5 V supply range and includes 54 I/O pins, nanoWatt eXtreme Low Power (XLP) technology, and a Charge Time Measurement Unit (CTMU) for capacitive touch sensing. An 8-bit microcontroller (MCU) is a single-chip computer that integrates a CPU, program memory (Flash), data memory (RAM), and peripherals on one die. PIC18F-series devices sit in Microchip's high-tier 8-bit family, positioned above baseline PIC16 parts and below the 16-bit dsPIC line, and are widely used where deterministic real-time control, low power, and rich on-chip peripherals matter more than raw MHz. The 'K90' sub-family adds segmented LCD drive and ultra-low-power XLP sleep modes, making the device a strong fit for battery-powered human-machine interface (HMI) products. Key features of the PIC18F67K90T-I/MR include 24 channels of 10-bit ADC, two I2C, two SPI, two USART (with LIN support) interfaces, a 16-bit timer/counter array, and a real-time clock calendar with battery backup mode. The integrated LCD driver supports up to 192 segments with contrast control, eliminating the need for an external LCD controller and reducing BOM cost in HMI designs. The CTMU enables 24 channels of capacitive touch measurement for buttons, sliders, and proximity sensing. Architecturally, the device uses Microchip's enhanced PIC18 RISC core with a modified Harvard bus and 16-bit opcodes, providing single-cycle instruction execution at 16 MIPS (64 MHz). Self-programmability under software control, dual oscillator blocks with fail-safe clock switching, and an extended instruction set with hardware multiply make the part well-suited to applications combining UI rendering, communication, and sensor processing on a single chip. The XLP technology delivers sleep currents under 100 nA typical and RTC run currents under 800 nA. Typical applications include battery-powered medical devices (glucose meters, infusion pumps), industrial control panels with LCD HMI, smart thermostats, wearable fitness trackers, home automation controllers, and automotive accessory clusters. The integrated LCD driver is the primary draw for products that need glass displays without an external charge-pump or controller IC. When designing with this MCU, pay close attention to the VQFN exposed-pad PCB land pattern. The thermal pad must be soldered to a properly sized copper pour to meet the thermal specifications and to provide the low-impedance ground return required by the analog and LCD subsystems. The supply decoupling network should use a 100 nF X7R bypass on each VDD/VSS pair as close to the package as possible, with a 10 uF bulk cap on the main rail. A high-precision external 32.768 kHz crystal is recommended when using the RTC calendar function. This page synthesizes distributor pricing, drop-in same-package alternatives from Microchip's own FFF alternates, and practical PCB/thermal design notes that go beyond the data-checklist style of the manufacturer datasheet, helping engineers evaluate the part for next-generation HMI designs.

見積もりお問い合わせ

PIC18F67K90T-I/MRRSL

PIC18F67K90T-I/MRRSL - 8-Bit 64MHz MCU 128KB Flash 64-VQFN | Microchip

The Microchip Technology PIC18F67K90T-I/MRRSL is a member of the PIC PIC XLP 18K family of 8-bit microcontrollers delivering 64 MIPS of CPU throughput at 64 MHz, with 128 KB of Flash program memory (64K x 16 organization), 4 KB of SRAM, and 1 KB of EEPROM, all integrated in a 64-pin Very-thin QFN (VQFN) 9 x 9 mm package with exposed thermal pad. It supports 53 digital I/O lines and operates across a wide 1.8 V to 5.5 V supply range, including the conventional 2.5 V, 3.3 V, and 5 V rails used in industrial and consumer designs. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, non-volatile program memory, volatile data memory, peripherals, and digital I/O onto one die. The PIC18 architecture is an enhanced 8-bit RISC Harvard core with 16-bit instruction words and 8-bit data paths, and it sits within the broader hierarchy: PIC18 -> 8-bit PIC -> microcontroller -> embedded controller -> semiconductor. The XLP 18K sub-family adds nanoWatt XLP low-power technology for energy-sensitive and battery-driven applications. Key features of the PIC18F67K90T-I/MRRSL include an integrated LCD driver with up to 192 segments suitable for character and segment displays, a Charge Time Measurement Unit (CTMU) for capacitive touch sensing across up to 24 channels, a 12-bit A/D converter with multiple input channels, three analog comparators, two USART, two MSSP (I2C/SPI), an 11-channel PWM / 11 timers block, a Real-Time Clock and Calendar (RTCC), and standard supervisory functions (POR, BOR, WDT). 64 MHz operation at low voltage extends to industrial-grade -40 C to +85 C (I suffix). The device employs a pipelined Harvard architecture with hardware multiply, table reads/writes, and a 31-level hardware stack, allowing deterministic interrupt response and efficient C compilation. Its nanoWatt XLP implementation supports deep sleep modes with sub-uA currents, making it attractive for line-powered and energy-harvesting designs where average power budget, not peak performance, is the gating constraint. Typical applications include battery-powered human-machine interface panels with segment LCD plus capacitive touch, e-meter and home-automation user interfaces, medical dosing pumps, industrial control keypads, white-goods user interface boards, and any sub-100-MIPS embedded design requiring segment displays alongside touch buttons. The wide 1.8 V to 5.5 V supply also supports direct Li-ion / two-AA operation without external regulators, simplifying the bill of materials. When laying out this VQFN-64 with exposed pad, the EP must be soldered to a continuous ground copper pour to achieve the datasheet thermal resistance; otherwise junction temperature rises quickly and the device may throttle or fail. Use the PIC18F87K90 family datasheet as the canonical reference for peripheral mapping, RTCC crystal selection, and CTMU calibration constants. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone.

見積もりお問い合わせ

PIC18F67K90T-I/PT

PIC18F67K90T-I/PT - 64MHz 8-bit PIC MCU 128KB Flash LCD TQFP-64

The Microchip Technology PIC18F67K90T-I/PT is an 8-bit PIC microcontroller operating at up to 64 MHz with 128 KB of Flash program memory and 4 KB of RAM, housed in a 64-pin TQFP (10x10 mm) package. It belongs to the PIC18F87K90 family and integrates an LCD driver, nanoWatt XLP ultra-low-power technology, a 12-bit ADC, and a Charge Time Measurement Unit (CTMU) module. An 8-bit microcontroller (MCU) is a single-chip computer that integrates a CPU, non-volatile program memory (Flash/ROM), volatile data memory (RAM), and a configurable set of peripheral interfaces into one package. Within the MCU hierarchy, this part is a CISC Harvard-architecture device in the PIC18 family, optimized for low-power embedded control with on-chip LCD driving. It uses a Flash-based program store allowing in-system re-programming and is widely deployed where battery life, an integrated glass driver, and rich I/O are critical. Key specifications include 128 KB (64K x 16) of Flash program memory, 4 KB of RAM, a maximum CPU clock of 64 MHz (16 MIPS instruction throughput), an operating voltage range of 1.8 V to 5.5 V (with the wider 4.2 V to 5.5 V datasheet band for full peripheral operation), 54 digital I/O pins, a 12-bit A/D converter, and an integrated LCD driver supporting up to 64 segments. The 'T' suffix denotes Tape & Reel packaging and the 'I' suffix denotes the industrial -40 C to +85 C operating temperature grade. The PIC18F67K90 uses Microchip's nanoWatt XLP technology, achieving sleep currents in the nanoamp range, making it suitable for battery-powered applications. The CTMU module enables capacitive touch sensing using the LCD electrodes, allowing touch-button interfaces on the same glass as the display. Hardware CRC, mTouch capacitive touch libraries, and RTCC with timestamp round out the on-chip feature set. Typical applications include battery-powered LCD instrumentation, household appliances with touch interfaces, medical glucose/infusion meters, industrial HMI panels, security keypads with displays, and any portable device that combines a segmented LCD with capacitive buttons. The integrated peripherals eliminate the need for an external LCD driver and a separate touch controller, reducing both BOM cost and PCB footprint. Designers should review the PIC18F87K90 family datasheet for the specific pinout, segment-channel mapping, and CTMU calibration procedure. The TQFP-64 land pattern is compatible with the wider PIC18F87K90 family (PIC18F87K90, PIC18F57K90), enabling a single PCB layout to accept multiple density variants.

見積もりお問い合わせ

PIC18F8310-E/PT

PIC18F8310-E/PT - 8KB Flash 70 I/O MCU | Microchip 80-TQFP

The Microchip PIC18F8310-E/PT is an 8-bit PIC microcontroller featuring 8 KB Flash program memory (4K x 16), 768 bytes of RAM, and 70 general-purpose I/O pins, housed in an 80-pin TQFP package. Operating at up to 25 MHz from a 5V supply, the device belongs to the PIC18F8310/8410 family that targets manufacturing equipment, instrumentation and monitoring, data acquisition, power conditioning, environmental monitoring, telecom, and consumer applications. What is an 8-bit PIC microcontroller? A microcontroller (MCU) is a single-chip computer that integrates a CPU, memory (Flash for program storage and RAM for working data), peripherals, and I/O. The PIC18F family uses an enhanced 8-bit RISC architecture with 16-bit wide instructions and Harvard bus design, sitting in the hierarchy: 8-bit MCU -> microcontroller -> embedded processor -> semiconductor. The 'F' in PIC18F denotes Flash program memory, enabling in-system reprogramming via ICSP (In-Circuit Serial Programming). Key features include the nanoWatt Technology power management suite for active and sleep current reduction, internal oscillator options that reduce external component count, and the 70 I/O lines that support multiple communication peripherals. The PIC18F8310 differs from the smaller-pin PIC18F6310 (64-pin) and PIC18F6410 (64-pin) siblings primarily by offering more I/O lines and the larger TQFP-80 footprint required for full peripheral parallelism. The device uses a 16-bit modified Harvard architecture with separate program and data buses, a hardware multiplier, and an 8-bit ALU. It supports the enhanced instruction set common across PIC18F families, plus peripheral modules including timers, capture/compare/PWM, USART, MSSP (SPI/I2C), and a 10-bit ADC. The -E temperature grade extends the operating range from -40C to +125C, making it suitable for industrial and extended-environment designs. Typical applications span industrial control panels, sensor conditioning boards, HVAC controls, low-cost motor drives, and serial-interface human-machine interface (HMI) modules. The 70 I/O support many parallel keypad/LED matrix designs without external I/O expanders, and the 8 KB Flash accommodates USB CDC firmware, MODBUS slave stacks, or simple RTOS kernels. Design considerations: provide a 0.1 uF decoupling capacitor near each VDD/VSS pair, route MCLR through a proper reset circuit, and verify oscillator configuration bits when migrating from prototype to production. For new designs, evaluate the newer PIC18F67K90 or PIC18F47K42 families which offer more memory and peripherals at lower cost. This page synthesizes distributor pricing, pin-to-pin drop-in alternatives, and practical design notes not consolidated in the manufacturer datasheet alone.

見積もりお問い合わせ

サブカテゴリ

製品 (32865)

PIC18F67J60T-I/PT - 8-Bit MCU w/ Ethernet, 128KB Flash | Microchip

PIC18F67J90-I/PT - 8-Bit MCU 128KB Flash 64-LCD TQFP | Microchip

PIC18F67J90T-I/PT - 8-Bit 48MHz 128KB Flash LCD MCU | Microchip

PIC18F67J93-I/PT - 8-Bit 48MHz 128KB Flash LCD MCU 64-TQFP | Microchip

PIC18F67J93T-I/PT - 128KB Flash LCD MCU, 64-TQFP | Microchip

PIC18F67J94-I/PT - 8-Bit 64MHz 128KB Flash USB XLP MCU | Microchip

PIC18F67K22-E/MR - 64-Pin 128KB Flash nanoWatt XLP MCU | Microchip

PIC18F67K22-E/PT - 8-bit MCU, 128KB Flash, 64-Pin TQFP | Microchip

PIC18F67K22-I/MR - 8-bit 64MHz 128KB Flash MCU | Microchip

PIC18F67K22-I/PT - 8-bit 64MHz 128KB Flash MCU | Microchip

PIC18F67K22-I/PTRSL - 8-Bit 64MHz XLP MCU, 128KB Flash, 64-TQFP | Microchip

PIC18F67K22T-I/MRRSL - 64MHz 8-bit MCU, 128KB Flash | Microchip

PIC18F67K22T-I/PT - 128KB Flash 8-bit XLP MCU | Microchip | TQFP-64

PIC18F67K40-E/PT - 64-Pin 8-bit MCU 128KB Flash XLP | Microchip

PIC18F67K40-I/PT - 8-bit 64MHz 128KB Flash XLP MCU | Microchip

PIC18F67K40T-I/MR - 128KB Flash XLP 8-bit MCU 64-VQFN | Microchip

PIC18F67K40T-I/PT - 8-Bit 64MHz 128KB Flash MCU | Microchip

PIC18F67K90-E/MR - 64-pin LCD MCU, 128KB Flash, XLP | Microchip

PIC18F67K90-E/PT - 8-bit 64MHz MCU 128KB Flash 64-TQFP | Microchip

PIC18F67K90-I/PT - 8-Bit 64MHz 128KB Flash LCD MCU | Microchip

PIC18F67K90T-I/MR - 128KB Flash 8-bit LCD MCU | Microchip

PIC18F67K90T-I/MRRSL - 8-Bit 64MHz MCU 128KB Flash 64-VQFN | Microchip

PIC18F67K90T-I/PT - 64MHz 8-bit PIC MCU 128KB Flash LCD TQFP-64

PIC18F8310-E/PT - 8KB Flash 70 I/O MCU | Microchip 80-TQFP