集積回路

サブカテゴリ

📁 ADC/DAC 3,100+ 製品 📁 アンプIC 1,900+ 製品 📁 オーディオコーデック 18 製品 📁 オーディオIC 2 製品 📁 クロック＆タイミング 670+ 製品 📁 Comparator ICs 1 製品 📁 DSP 1,100+ 製品 📁 データ収集IC 2 製品 📁 デジタルポテンショメータ 4 製品 📁 ディスプレイドライバ＆コントローラ 1 製品 📁 FPGA & CPLD 7,300+ 製品 📁 インターフェースIC 3,400+ 製品 📁 LEDドライバ 1 製品 📁 ロジックIC 460+ 製品 📁 メモリIC 870+ 製品 📁 マイクロコントローラ 20,000+ 製品 📁 マイクロプロセッサ 4 製品 📁 モータドライバ 1 製品 📁 その他 1 製品 📁 Sensor and Detector Interfaces 1 製品 📁 専用IC 15 製品 📁 ビデオIC 14 製品

製品 (39,000+)

INA186A3IDCKR - 40V Bidirectional Current Sense Amp | TI
INA186A3IDCKR

INA186A3IDCKR - 40V Bidirectional Current Sense Amp | TI

The Texas Instruments INA186A3IDCKR is a 40 V, bidirectional, high-precision, low-power, zero-drift current-sense amplifier in a 6-pin SC-70 (DCK) package. The A3 gain variant sets the fixed internal gain to 100 V/V, and the device accepts common-mode voltages from -0.2 V to +40 V independently of the supply rail. A current-sense amplifier (CSA, also called a current-shunt monitor) is an analog IC that measures the small differential voltage developed across a shunt resistor in series with a load, and converts it to a ground-referenced output voltage proportional to load current. CSAs sit in the signal-chain hierarchy: shunt resistor -> current-sense amplifier -> ADC / MCU / comparator, and they are essential building blocks in the power-management sub-system for accurate telemetry and protection. Key features include a low offset voltage enabled by the zero-drift chopper architecture, picoamp-level input bias current that supports large shunt values for microamp measurements, a low quiescent current (typically tens of microamps) suitable for always-on battery monitoring, an integrated ENABLE pin for power gating, and rail-to-rail output swing for full-scale ADC input utilization. The A3 fixed gain of 100 V/V provides 20 mV/V sensitivity. The architecture combines a precision chopper-stabilized input stage with an internal gain-setting resistor network, eliminating the external gain resistors required by discrete difference-amplifier implementations. The high common-mode rejection and picoamp bias allow designers to use larger sense resistors for better signal-to-noise without measurable loading error. Typical applications include battery-cell monitoring in battery management systems (BMS), USB-C current advertisement and overcurrent protection, motor-phase current sensing in BLDC drivers, solar MPPT input-current telemetry, and precision 24 V industrial-sensor rails. Design tip: pick the A1/A2/A3/A4/A5 gain variant by matching your full-scale shunt voltage to the ADC input range; keep the shunt Kelvin-connected to the IN+/IN- pins and use a 4-wire layout to preserve CMRR at high dV/dt. This page consolidates authorized-distributor pricing for the INA186A3IDCKR, true drop-in alternatives in the same SC-70-6 footprint, and PCB design guidance that goes beyond the manufacturer datasheet.

見積もり お問い合わせ
INA188ID - 36V Zero-Drift Instrumentation Amplifier | Texas Instruments
INA188ID

INA188ID - 36V Zero-Drift Instrumentation Amplifier | Texas Instruments

The Texas Instruments INA188ID is a single-channel, 36 V zero-drift instrumentation amplifier with rail-to-rail output, selectable gain from 1 to 1000, and an 8-pin SOIC package. It provides a gain of 1 + (50 kΩ/RG), allowing one external resistor to set the gain while preserving the established instrumentation-amplifier connection. According to the Texas Instruments product page, the INA188ID is intended for precision signal measurement and sensor conditioning, including temperature sensing and bridge-based measurements, and is specified over a -40°C to +125°C temperature range. An instrumentation amplifier is a specialized differential amplifier that measures a small voltage difference between two inputs while offering high input impedance, common-mode rejection, and gain accuracy. The INA188 belongs to the zero-drift instrumentation-amplifier family, a subtype of precision analog amplifiers used for sensor interfaces, current measurement, biomedical instrumentation, and industrial process control. Its internal auto-zeroing techniques reduce offset voltage and offset drift, making it more suitable for slowly varying precision signals than a conventional amplifier whose offset moves with temperature. Key features include a 36 V maximum supply voltage, rail-to-rail output operation, gains from 1 to 1000, and a maximum input offset voltage of 55 µV as reported by the comparative distributor data. The reference pin supports output level shifting in single-supply systems and offset calibration. A single gain-setting resistor simplifies design-in, while the zero-drift architecture addresses offset stability in temperature, bridge, and slow-current-measurement systems. The 8-pin SOIC package also supports conventional surface-mount assembly. The gain relationship G = 1 + (50 kΩ/RG) allows the sensor interface to be scaled without an active gain network. For example, a 1 kΩ gain resistor produces a nominal gain of 51, while a 50 Ω resistor produces a nominal gain of 1001 before rounding and standard gain-error considerations are applied. The reference input provides an additional analog node for systems that cannot shift their output entirely in the analog domain. Designers should preserve the instrumentation-amplifier grounding and input-common-mode requirements when evaluating usable signal range. Typical uses include strain-gauge and load-cell bridges, RTD and thermocouple signal conditioning, precision current-shunt measurements, battery monitoring, and low-level sensor acquisition. The INA188ID is particularly appropriate when low offset and low drift matter more than wideband response. In bridge systems, its differential input arrangement and adjustable gain can amplify the small bridge imbalance while limiting sensitivity to common-mode voltage. In battery-powered equipment, the reference pin can place the output within the usable range of a single-supply analog-to-digital converter. The primary design consideration is ensuring that input and output common-mode voltages remain inside the device's operating limits at every gain and supply condition. Gain-set resistor tolerance contributes directly to gain accuracy, so precision resistors may be required for calibrated measurements. Input filtering, source impedance, reference-pin routing, and exposed-area thermal management should also be evaluated before production release. This product page consolidates manufacturer specifications, verified distributor pricing, package details, comparison data, and practical design guidance. It also distinguishes verified drop-in candidates from broader functional alternatives so engineers can assess footprint, gain-setting, voltage-range, and precision differences before changing a production design.

見積もり お問い合わせ
INA188IDR - 36V Zero-Drift Instrumentation Amplifier | Texas Instruments (Tape & Reel)
INA188IDR

INA188IDR - 36V Zero-Drift Instrumentation Amplifier | Texas Instruments (Tape & Reel)

The Texas Instruments INA188IDR is a single-channel, 36 V zero-drift instrumentation amplifier with rail-to-rail output, selectable gain from 1 to 1000, and an 8-pin SOIC package. It provides a gain of 1 + (50 kΩ/RG), allowing one external resistor to set the gain while preserving the established instrumentation-amplifier connection. According to the Texas Instruments product page, the INA188IDR is intended for precision signal measurement and sensor conditioning, including temperature sensing and bridge-based measurements, and is specified over a -40°C to +125°C temperature range. An instrumentation amplifier is a specialized differential amplifier that measures a small voltage difference between two inputs while offering high input impedance, common-mode rejection, and gain accuracy. The INA188 belongs to the zero-drift instrumentation-amplifier family, a subtype of precision analog amplifiers used for sensor interfaces, current measurement, biomedical instrumentation, and industrial process control. Its internal auto-zeroing techniques reduce offset voltage and offset drift, making it more suitable for slowly varying precision signals than a conventional amplifier whose offset moves with temperature. Key features include a 36 V maximum supply voltage, rail-to-rail output operation, gains from 1 to 1000, and a maximum input offset voltage of 55 µV as reported by the comparative distributor data. The reference pin supports output level shifting in single-supply systems and offset calibration. A single gain-setting resistor simplifies design-in, while the zero-drift architecture addresses offset stability in temperature, bridge, and slow-current-measurement systems. The 8-pin SOIC package also supports conventional surface-mount assembly. The gain relationship G = 1 + (50 kΩ/RG) allows the sensor interface to be scaled without an active gain network. For example, a 1 kΩ gain resistor produces a nominal gain of 51, while a 50 Ω resistor produces a nominal gain of 1001 before rounding and standard gain-error considerations are applied. The reference input provides an additional analog node for systems that cannot shift their output entirely in the analog domain. Designers should preserve the instrumentation-amplifier grounding and input-common-mode requirements when evaluating usable signal range. Typical uses include strain-gauge and load-cell bridges, RTD and thermocouple signal conditioning, precision current-shunt measurements, battery monitoring, and low-level sensor acquisition. The INA188IDR is particularly appropriate when low offset and low drift matter more than wideband response. In bridge systems, its differential input arrangement and adjustable gain can amplify the small bridge imbalance while limiting sensitivity to common-mode voltage. In battery-powered equipment, the reference pin can place the output within the usable range of a single-supply analog-to-digital converter. The primary design consideration is ensuring that input and output common-mode voltages remain inside the device's operating limits at every gain and supply condition. Gain-set resistor tolerance contributes directly to gain accuracy, so precision resistors may be required for calibrated measurements. Input filtering, source impedance, reference-pin routing, and exposed-area thermal management should also be evaluated before production release. This product page consolidates manufacturer specifications, verified distributor pricing, package details, comparison data, and practical design guidance. It also distinguishes verified drop-in candidates from broader functional alternatives so engineers can assess footprint, gain-setting, voltage-range, and precision differences before changing a production design.

見積もり お問い合わせ
INA188IDRJR - 36V Zero-Drift Instrumentation Amplifier | Texas Instruments
INA188IDRJR

INA188IDRJR - 36V Zero-Drift Instrumentation Amplifier | Texas Instruments

The Texas Instruments INA188IDRJR is a precision, zero-drift, rail-to-rail output, high-voltage instrumentation amplifier housed in an 8-pin SON (4x4 mm) package with an exposed thermal pad. It delivers 55 uV (max) input offset voltage, 0.2 uV/°C (max) input offset drift, and 104 dB (min) CMRR at gains of 10 or higher. The part operates from a wide 4 V to 36 V single supply (or ±2 V to ±18 V dual supply), accepting input signals up to the rails while swinging its output rail-to-rail. An instrumentation amplifier (INA) is a specialized differential amplifier designed for precise amplification of small differential signals in the presence of large common-mode voltages. Compared to a general-purpose op-amp built from three discrete amplifiers, an INA integrates the input buffer, gain stage, and difference amplifier into one laser-trimmed silicon block, achieving far higher common-mode rejection ratio (CMRR), lower offset drift, and far simpler single-resistor gain setting. INAs sit hierarchically inside the sensor signal-chain / analog front-end / mixed-signal IC family and are the building block of choice for bridge sensors, thermocouples, RTDs, and biomedical instrumentation. Key features include 12 nV/√Hz input voltage noise density at 1 kHz, 0.25 uVPP (0.1 Hz to 10 Hz) low-frequency noise, an industry-standard gain equation G = 1 + (50 kΩ / RG) settable from 1 V/V to 1000 V/V with a single external resistor, and a reference pin for level-shifting in single-supply operation or for offset calibration. The integrated zero-drift (chopper-stabilized) topology continuously nulls its own 1/f noise and offset, eliminating the need for periodic user calibration. The INA188 uses TI's proprietary auto-zero / chopper-stabilized architecture combined with thin-film resistor networks for the gain-setting feedback. This delivers near-ideal DC accuracy without the discrete capacitor or clock-noise artifacts of older chopper designs, while the 4 mm x 4 mm SON package exposes its complementary efficiency rating to standard SOIC-8 boards through its thermal pad. Typical applications include weigh scales and bridge sensor signal conditioning, thermocouple and RTD temperature measurement, medical instrumentation (ECG, EEG front ends), industrial process controls, and strain-gauge amplifier chains. The wide 4 V to 36 V supply range makes it a direct fit for industrial 24 V bus systems. When designing, place the gain-setting resistor close to the RG pins and add a 0.1 uF supply bypass capacitor on each supply pin; the exposed thermal pad must be soldered to a copper pad for rated thermal performance. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

見積もり お問い合わせ
INA190A1IRSWR - 40V Picoamp Current Sense Amp | TI
INA190A1IRSWR

INA190A1IRSWR - 40V Picoamp Current Sense Amp | TI

The Texas Instruments INA190A1IRSWR is a 40V bidirectional, zero-drift current sense amplifier (current-shunt monitor) with picoampere input bias current and an enable pin, housed in a 10-pin UQFN (RSV, 1.8 mm x 1.4 mm) package. It senses voltage drops across shunt resistors at common-mode voltages from -0.2 V to +40 V, independent of its 1.8 V-class low supply. A current sense amplifier is a specialized difference amplifier that measures the small voltage generated across a shunt resistor and converts it into a ground-referenced output signal. Within the power-management hierarchy, it sits between the shunt and an ADC or comparator, enabling precise current measurement for feedback, protection, and telemetry in systems from battery packs to industrial drives. Key features of the INA190 family include a very wide input common-mode range (-0.2 V to 40 V) that tolerates inductive kickback and reverse-battery events, ultra-low input bias current in the picoampere range that permits very small shunt resistors, and zero-drift architecture for near-DC accuracy. The INA190A1IRSWR offers an ENABLE pin for power-cycling in battery-powered designs and operates across -40C to +125C. Technically, the device uses a zero-drift (auto-zeroing) topology that eliminates offset drift over time and temperature, achieving precision far beyond conventional CMOS amplifiers. The low bias current allows shunts in the milliohm range without significant self-heating error, while the wide common-mode range permits high-side, low-side, and bidirectional sensing with a single supply. The voltage-output interface connects directly to ADCs without external conditioning. Typical applications include overcurrent protection in USB and battery-powered systems, precision current telemetry in notebooks and IoT devices, and closed-loop current feedback in industrial controls, where low shunt losses and accuracy at low supply voltages are essential. Design consideration: because the part supports a 1.8 V supply domain, verify the output swing and reference pin drive against your ADC input range to avoid clipping near the rails. This page synthesizes distributor pricing, drop-in alternatives, pinout guidance, and practical design notes not found in the manufacturer datasheet.

見積もり お問い合わせ
INA190A2IDDFR - 40V Bidirectional Current Sense Amp | TI
INA190A2IDDFR

INA190A2IDDFR - 40V Bidirectional Current Sense Amp | TI

The Texas Instruments INA190A2IDDFR is a 40-V bidirectional, ultra-precise current-sense amplifier with picoamp-level input bias current and an integrated ENABLE pin, offered in an 8-pin TSOT-23 (DDF) package. The A2 gain option delivers a fixed 50 V/V transimpedance, supporting common-mode voltages from -0.2 V to +40 V independent of the supply rail. The zero-drift chopper-stabilized architecture keeps input offset voltage below 15 uV (typical 5 uV) and offset drift below 0.1 uV/C, which translates directly into accurate microamp-range current measurements when paired with a small shunt. A current-sense amplifier is an analog building block that converts a small differential voltage developed across a shunt resistor into a ground-referenced output voltage proportional to load current. The INA190 family belongs to the current-sense amplifier / instrumentation amplifier / signal-chain IC / analog IC taxonomy, sitting one level below general-purpose op-amps because it integrates a precision gain network and reference-stable input stage optimized for high common-mode rejection at high voltages. This category plays a central role in modern power management, where system optimization, telemetry, and closed-loop feedback demand accurate, low-latency current data. Key features include a 1.8-V to 5.5-V supply range, 65 uA typical quiescent current, 60 V common-mode transient immunity, and 40 kHz small-signal bandwidth. Output swings rail-to-rail and the device supports low-side, high-side, and bidirectional topologies, eliminating external protection circuitry in 12-V, 24-V, and 48-V industrial buses. The picoamp input bias current allows sense resistors up to tens of kilo-ohms, which is critical for monitoring sleep-mode current in battery-powered products without degrading accuracy. The zero-drift chopper architecture continuously nulls 1/f noise and thermal drift, yielding effectively DC-stable output over the full -40C to +125C operating range. The internal EN pin lets a microcontroller gate the supply current down to a sub-microamp leakage level, which is essential for always-on battery systems that must periodically wake to perform current sampling. Combined, these characteristics make the INA190A2 one of the lowest-noise, lowest-drift current-sense amplifiers in its class. Typical applications include USB-PD and Type-C cable-compensation, motor-control current loops, solar MPPT input monitors, battery-pack gas-gauging, and point-of-load telemetry in servers and telecom rectifiers. The fixed 50 V/V gain optimizes the part for low-current (sub-amp) measurements where the A1 (25 V/V) is too noisy and the A3 (100 V/V) or A4 (200 V/V) variants sacrifice dynamic range. A key design consideration is the trade-off between shunt resistance and dissipated power: choose a 50 V/V part when the load is typically below 1 A and milliohm shunts are preferred, and place the input capacitor network as close as possible to the IN+ and IN- pins to reject high-frequency transients on the common-mode bus. This page synthesizes distributor pricing, drop-in alternatives in the same TSOT-23-8 footprint, and practical design notes that go beyond the manufacturer datasheet to help engineers select, source, and qualify the INA190A2IDDFR for their next precision current-monitoring design.

見積もり お問い合わせ
INA210BQDCKRQ1 - AEC-Q100 26V Bi-Directional Current Sense Amp | TI
INA210BQDCKRQ1

INA210BQDCKRQ1 - AEC-Q100 26V Bi-Directional Current Sense Amp | TI

The Texas Instruments INA210BQDCKRQ1 is an AEC-Q100 qualified, 26 V, bi-directional, high-precision current sense amplifier (also called a current-shunt monitor) housed in a 6-pin SOT-SC70 (DCK) package. It senses voltage drops across shunt resistors at common-mode voltages from -0.3 V to 26 V, independent of the supply voltage, and delivers an analog output proportional to the sensed current with a fixed gain of 200 V/V. A current sense amplifier is a specialized analog building block that converts a small differential voltage developed across a current-sense (shunt) resistor into a ground-referenced, amplified output voltage. It sits in the signal chain between the shunt resistor (placed in series with the load) and the downstream ADC, microcontroller, or comparator, and belongs to the broader hierarchy of instrumentation amplifiers -> operational amplifiers -> analog ICs. Zero-drift chopper-stabilized topology enables the INA210 family to achieve microvolt-level offset and excellent common-mode rejection. Key features include a maximum offset voltage of 35 uV, a gain error of only 0.5 percent (max), and 40 kV/us slew rate, plus a 2.7 V to 26 V supply range with 65 uA typical quiescent current. The device offers bidirectional sensing (REF input allows positive or negative current measurement), operates from -40C to +125C, and integrates EMI filtering plus thermal shutdown. The SC70-6 package occupies roughly 2.1 mm x 1.45 mm of PCB area, ideal for compact automotive modules. The INA210 uses a chopper-stabilized input stage and precision thin-film resistors to achieve gain accuracy and ultra-low offset drift over temperature. Its high common-mode rejection ratio (CMRR) of 140 dB and the ability to operate with the input common-mode above V+ make it tolerant of inductive loads, motor inrush, and 12 V/24 V automotive transients such as load-dump. Typical applications include automotive body electronics (battery management, ECU power monitoring), motor control current loops, solenoid and valve actuation feedback, USB Type-C current advertisement (BC 1.2), and precision 48 V telecom/industrial rails. The combination of AEC-Q100 qualification, wide common-mode range, and small package makes it especially well-suited for safety-relevant automotive systems. When designing with this device, place the shunt resistor close to the input pins to minimize parasitic resistance, use Kelvin connection to the shunt, and add a small RC filter at the output to limit noise bandwidth. Choose the shunt value so that the maximum differential input (Vshunt_max = VSENSE_max / 200) does not exceed the linear input range, accounting for transient overloads. This page synthesizes distributor pricing, same-brand and cross-brand drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone.

見積もり お問い合わせ
INA2126P - Dual 36V Micropower Instrumentation Amplifier | Texas Instruments
INA2126P

INA2126P - Dual 36V Micropower Instrumentation Amplifier | Texas Instruments

The Texas Instruments INA2126P is a dual-channel, micropower precision instrumentation amplifier designed for accurate differential-signal acquisition. Each channel uses a two-op-amp architecture and consumes 175 µA of quiescent current, while the device operates from ±1.35 V to ±18 V, equivalent to a 36 V maximum total supply range. The INA2126P provides 250 µV offset performance and is supplied in a 16-pin PDIP package for through-hole PCB designs. An instrumentation amplifier is a specialized analog signal-conditioning IC that amplifies the voltage difference between two inputs while rejecting common-mode interference. The INA2126 family belongs to the instrumentation amplifier hierarchy, which includes differential amplifiers, low-noise analog amplifiers, and broader analog signal-chain ICs. Its differential-input architecture makes it suitable for sensor signals, bridge outputs, and other small-signal measurements where the wanted signal is small relative to an imposed common-mode voltage. The principal features of the INA2126P are its dual-channel configuration, 175 µA per channel quiescent current, 250 µV offset specification, and wide ±1.35 V to ±18 V operating range. Micropower consumption reduces the burden on portable and battery-powered systems, while the wide supply range supports both low-voltage portable instrumentation and higher-voltage industrial measurement systems. The differential architecture also helps preserve signal integrity when the input common-mode voltage is substantially larger than the differential signal being measured. The INA2126 family uses a two-op-amp instrumentation-amplifier topology to provide differential amplification with high input impedance and common-mode rejection. Because the device is intended for precision acquisition rather than high-bandwidth signal processing, designers should use the manufacturer-recommended gain-setting resistor and follow the datasheet layout guidance to minimize gain error and offset contributions. The 16-pin PDIP package favors through-hole prototyping, laboratory instrumentation, and industrial control boards where a surface-mount package is not required. Typical applications include portable sensor acquisition, strain-gauge and bridge excitation systems, battery-powered measurement equipment, industrial process monitoring, medical instrumentation, and low-power data-acquisition systems. In each case, the INA2126P provides a practical way to amplify a differential sensor signal while keeping channel quiescent current at 175 µA. Designers should confirm that input common-mode voltage, output swing, gain, bandwidth, and supply limits satisfy the specific measurement requirements. The primary design consideration is ensuring adequate output headroom and checking the gain-dependent bandwidth and input range. The 250 µV offset specification supports precise measurements, but resistor matching and layout still influence overall system accuracy. Input filtering and guarding can reduce high-frequency interference, while stable reference and excitation arrangements are important for bridge-based sensors. This product page combines the verified Texas Instruments product information, distributor availability references, pricing context, package details, and engineering selection guidance to provide a practical comparison point for engineers evaluating the INA2126P.

見積もり お問い合わせ
INA2126U - 36V Dual Micropower Instrumentation Amplifier | Texas Instruments
INA2126U

INA2126U - 36V Dual Micropower Instrumentation Amplifier | Texas Instruments

The Texas Instruments INA2126U is a dual-channel, 36 V micropower precision instrumentation amplifier with 250 µV offset, 175 µA quiescent current per channel, and a 16-pin SOIC package. It supports a wide ±1.35 V to ±18 V operating range and is designed for accurate, low-noise differential-signal acquisition. The device provides a gain range of 5 to 10000, a typical gain-bandwidth product of 200 kHz, and a typical input noise density of 0.4 nV/√Hz at 1 kHz. An instrumentation amplifier is a precision analog signal-conditioning IC that converts a small differential input into a single-ended or differential output. Its internal gain stage rejects common-mode interference and permits accurate measurement of low-level sensor signals. In the product hierarchy, an instrumentation amplifier belongs to the amplifier IC family, specifically the precision measurement and signal-conditioning category. It is distinct from a general-purpose operational amplifier because it integrates input buffering, differential subtraction, and gain-setting resistors. The INA2126U combines a gain range of 5 to 10000 with low offset and low noise. Its 250 µV maximum input offset supports accurate measurements at relatively high gain, while the 0.4 nV/√Hz typical noise density helps preserve weak-signal information. Two amplifiers are provided in each package, making the device useful when a system needs two independent differential measurement channels without using two separate packages. The two-op-amp architecture keeps quiescent current to 175 µA per channel, which is important in battery-powered equipment. The 200 kHz typical gain-bandwidth product provides useful bandwidth for slow sensor signals rather than high-speed video or communications signals. An operating supply of ±1.35 V to ±18 V allows operation from low-voltage portable rails through ±15 V industrial measurement systems, subject to the device's 36 V maximum total supply range. Typical uses include battery-powered portable instrumentation, low-level bridge and transducer measurement, industrial sensor acquisition, precision current sensing, and differential signal conditioning. The dual-channel organization can support two sensors in one instrument, while the micropower operation reduces the effect of the amplifier on battery life. Input common-mode and output swing limits must still be checked against the intended sensor and supply rails. Designers should use the gain-setting resistors and input common-mode network specified by the manufacturer, keep sensitive input traces short, and provide suitable bypassing close to the supply pins. The input network must also avoid excessive imbalance between the differential inputs because that can affect common-mode rejection and gain accuracy. Output loading and downstream ADC acquisition time should be evaluated together. This page combines manufacturer specifications, verified distributor availability, and practical comparison guidance with same-package alternatives. It also identifies missing pricing, pin-definition, environmental, and compliance details instead of estimating them, supporting faster component selection for precision analog designs.

見積もり お問い合わせ
INA2128P - Dual Precision Instrumentation Amplifier | TI
INA2128P

INA2128P - Dual Precision Instrumentation Amplifier | TI

The Texas Instruments INA2128P is a dual, low-power instrumentation amplifier with two independent amplifiers, a gain range of 1 to 10,000, and a 200 kHz bandwidth at a gain of 100. The device is offered in a 16-pin PDIP package. Its precision characteristics include 50 uV maximum offset voltage, 0.5 uV/degree C maximum input offset drift, 5 nA maximum input bias current, and 120 dB minimum common-mode rejection. An instrumentation amplifier is a differential analog signal-conditioning IC that amplifies the voltage difference between two inputs while rejecting common-mode interference. In the signal-chain hierarchy, an instrumentation amplifier is a specialized amplifier, a precision analog front end, and an active analog integrated circuit. The INA2128P uses a three-op-amp arrangement and current-feedback input circuitry to preserve useful bandwidth even when relatively high gain is selected. A single external resistor sets the gain from 1 to 10,000, simplifying adjustment during design and calibration. The 200 kHz bandwidth available at gain 100 supports accurate amplification of sensors and low-frequency measurement signals without requiring the bandwidth of a high-speed instrumentation amplifier. Input protection extending to plus or minus 40 V also helps control fault energy applied to the input pins, although it does not eliminate the need for normal application-level protection. The INA2128P provides two amplifier circuits in one package, allowing a dual-channel design to reduce board area and component count. Its low offset voltage and low drift are particularly useful when the amplified differential signal is small relative to the measurement resolution. The specified 120 dB minimum common-mode rejection helps suppress noise and voltage that appears equally on both inputs, while the low 5 nA maximum input bias current suits high-impedance sources. Typical uses include bridge-sensor signal conditioning, portable instrumentation, biomedical measurement, industrial process monitoring, and two-channel sensor acquisition. The device can also amplify differential outputs from transducers where low offset and common-mode rejection are more important than wide-bandwidth conversion performance. Designers should follow the manufacturer datasheet for the gain-setting resistor, supply bypassing, input protection, and pin assignments. The power-supply range is plus or minus 18 V, so both positive and negative rails are permitted when the circuit requires bipolar input or output ranges. Decoupling capacitors should be placed close to the supply pins, and source impedance should remain compatible with the amplifier's bias-current and bias-voltage requirements. This page combines verified manufacturer and distributor information with package-aware alternatives, application guidance, and engineering-focused selection notes. It also separates verified INA2128P data from parameters that require confirmation in the full datasheet, helping engineers plan a board revision without treating incomplete data as guaranteed specifications.

見積もり お問い合わせ
INA2128PA - Dual Instrumentation Amplifier | Texas Instruments
INA2128PA

INA2128PA - Dual Instrumentation Amplifier | Texas Instruments

The Texas Instruments INA2128PA is a dual, low-power, general-purpose instrumentation amplifier with gains from 1 to 10,000, a 16-pin PDIP package, and operation over -40°C to +85°C. It uses a current-feedback input architecture to maintain a bandwidth of 200 kHz at a gain of 100, while providing low offset voltage, low offset drift, high common-mode rejection, and input protection to ±40 V. An instrumentation amplifier is a precision analog signal-conditioning IC that amplifies the difference between two input voltages while rejecting signals common to both inputs. Its internal three-op-amp architecture supports accurate differential measurements from low-level sensors. Within the broader semiconductor hierarchy, an instrumentation amplifier belongs to the amplifier IC and analog signal-conditioning categories, where it sits between a sensor or bridge and a measurement, control, or data-conversion system. Key features include a maximum offset voltage of 50 µV, maximum offset drift of 0.5 µV/°C, maximum input bias current of 5 nA, and minimum common-mode rejection of 120 dB. A single external resistor sets the gain from 1 to 10,000. The dual configuration provides two independent amplifier channels, allowing one package to serve differential measurements or multiple sensor inputs. The current-feedback input circuitry is the principal performance feature. Unlike a voltage-feedback instrumentation amplifier that loses bandwidth as gain increases, the INA2128 family retains useful bandwidth at high closed-loop gain; the specified bandwidth is 200 kHz at gain 100. The three-op-amp topology also makes the input bias-current behavior relatively insensitive to source impedance, which is valuable when the source is a strain gauge, thermocouple, bridge, or other high-impedance sensor. Typical applications include bridge-based pressure and load-cell measurements, biomedical instrumentation, current-loop sensing, precision data acquisition, and low-level differential signal conditioning. The ±40 V input protection expands the usable fault-tolerance range, but it does not permit operation beyond the device's stated supply-voltage ratings. Designers should still limit input transients and maintain common-mode voltage within the operating region described by the manufacturer datasheet. The primary design consideration is gain-setting resistor selection because the external resistor determines gain while also affecting bandwidth, noise, and allowable operating range. Place the gain-setting resistor close to the corresponding gain resistor pins, maintain symmetrical input routing, provide adequate supply bypassing, and use a stable reference ground. This page combines device specifications, application guidance, lifecycle information, and drop-in alternative evaluation for faster engineering selection. For a dual-channel instrumentation amplifier where PCB area is limited, the INA2128PA provides a direct fit in a 16-pin PDIP footprint. The through-hole package also supports prototype and industrial repair workflows where a surface-mount assembly process would add unnecessary handling complexity.

見積もり お問い合わせ
INA2128U - Dual Precision Instrumentation Amplifier | TI
INA2128U

INA2128U - Dual Precision Instrumentation Amplifier | TI

The Texas Instruments INA2128U is a dual, low-power, general-purpose instrumentation amplifier packaged in a 16-pin SOIC. It uses a versatile three-op-amp architecture and current-feedback input circuitry to support broad bandwidth even at high gain. A single external gain-setting resistor provides gains from 1 to 10,000, while the two independent amplifier channels support simultaneous differential measurements or dual-channel sensing. An instrumentation amplifier is a specialized analog amplifier designed to measure small differential voltages accurately in the presence of large common-mode voltages. Its typical signal-chain hierarchy is differential input -> instrumentation amplifier -> precision analog measurement or control system. The INA2128U supports input-referenced and ground-referenced sensing, where unwanted signals common to both inputs are rejected while the differential component is amplified. The principal benefits of the INA2128U are its dual-channel configuration, selectable gain from 1 to 10,000, and bandwidth of 200 kHz at a gain of 100. Current-feedback input circuitry helps preserve usable bandwidth as gain increases. The low-power architecture is suitable for compact analog measurement systems, portable instrumentation, and industrial equipment where two precision analog channels must fit into a small board area. Internally, each channel follows a three-op-amp instrumentation-amplifier topology. Differential input currents are directed toward internal feedback paths, while a single external resistor establishes the gain relationship. Because the circuit supports both single-ended and differential input arrangements, engineers can adapt it to sensor bridges, shunt measurements, and bipolar input signals. The dual organization also allows synchronized acquisition of two related signals without requiring two separate packages. Typical uses include medical instrumentation, industrial sensor interfaces, battery-powered measurement equipment, current-shunt monitoring, and precision data-acquisition systems. Differential inputs are particularly useful when a sensor produces a small voltage riding on a larger common-mode voltage. Pairing the two channels can also support gain-and-offset measurement, comparator-style monitoring, or sampled systems requiring closely matched amplifier paths. A practical design must account for the external gain resistor, input and output settling, reference-ground connection, supply decoupling, and common-mode range. Place the gain-setting resistor close to the device and use the manufacturer's recommended layout and decoupling guidance. Maintain the input and output common-mode voltages within the operating limits, and verify system settling at the highest gain required by the measurement bandwidth. This product page organizes the manufacturer's functional description, package information, comparison considerations, and application guidance into one engineering-focused resource. It also identifies where pin-level and qualification details must be checked in the manufacturer datasheet before a new board is released to production.

見積もり お問い合わせ
INA2132U - Dual 36V Difference Amplifier | Texas Instruments
INA2132U

INA2132U - Dual 36V Difference Amplifier | Texas Instruments

The Texas Instruments INA2132U is a dual, low-power, single-supply difference amplifier operating from 2.7 V to 36 V and providing two matched amplifier channels in a 14-pin SOIC package. Its input stage supports common-mode voltages from -15 V to 28 V, while a minimum common-mode rejection ratio of 76 dB helps reject equal-magnitude signals applied to both inputs. The device operates over a -40 °C to 85 °C temperature range and is suitable for industrial measurement, sensing, and signal-conditioning systems. A difference amplifier measures the voltage between two input nodes rather than amplifying a single node relative to ground. In the signal-chain hierarchy, the INA2132U is a difference amplifier, which is a subtype of instrumentation amplifier, and ultimately belongs to the broader amplifier and analog signal-conditioning categories. The dual-channel configuration allows one package to handle two differential sensing channels while maintaining consistent amplifier characteristics between them. Key features include the 2.7 V to 36 V single-supply operating range, 76 dB minimum common-mode rejection, and a -40 °C to 85 °C industrial temperature rating. The low-power architecture is appropriate for systems in which every milliampere affects battery life, thermal rise, or analog headroom. A common-mode range extending below ground makes the device useful in shunt-monitoring systems where the signal may be referenced to a supply rail rather than to ground. The INA2132U is designed for differential measurements where the useful information is small compared with the common-mode voltage. Both amplifier channels are implemented in the same device, which supports matched measurements and reduces the number of external packages required. Its SOIC package also supports conventional surface-mount assembly, although exposed-pad thermal management is not specified in the available ordering information. Typical applications include high-side or low-side current sensing, bridge-sensor signal conditioning, battery monitoring, industrial process measurement, and differential voltage acquisition. When designing around this part, verify the signal amplitude, common-mode limits, and output-swing requirements against the application before committing the footprint. This page combines manufacturer product information, verified distributor pricing and availability, and engineering guidance that goes beyond a basic distributor listing. It also documents where additional datasheet parameters are required so engineers can distinguish confirmed values from information that must still be checked against the manufacturer datasheet.

見積もり お問い合わせ
INA2133U - Dual 1.5MHz Precision Difference Amplifier | TI
INA2133U

INA2133U - Dual 1.5MHz Precision Difference Amplifier | TI

Texas Instruments INA2133U is a dual-channel, unity-gain precision difference amplifier built around laser-trimmed precision resistor networks. The verified manufacturer information identifies a 1.5 MHz bandwidth, a maximum offset voltage of 450 µV, approximately 0.95 mA of power consumption, and a 14-pin SOIC package. These characteristics position the INA2133U as a high-speed instrumentation amplifier for measuring small differential signals superimposed on larger common-mode voltages. A difference amplifier is an analog signal-conditioning IC that subtracts two input voltages and amplifies the resulting differential component. In the broader electronics hierarchy, it belongs to the instrumentation-amplifier family, which sits within precision analog amplifiers, analog ICs, and semiconductors. Such devices are commonly used to reject common-mode interference, amplify sensor outputs, and preserve signal integrity between sensors and analog-to-digital converters. The INA2133U provides two precision difference amplifiers in one 14-pin SOIC package. Its 1.5 MHz bandwidth supports signal acquisition beyond very slow sensor applications, while the 450 µV maximum offset specification limits input-referred error during low-level measurements. The low 0.95 mA power figure also makes it relevant to compact industrial, communications, and test equipment where each milliampere affects thermal and power-budget requirements. According to the Texas Instruments product page, the device is designed for high-speed precision differential signal conditioning. Internally, the INA2133 combines a precision operational-amplifier core with an on-chip, laser-trimmed resistor network. The manufacturer describes the INA133 and INA2133 families as unity-gain difference amplifiers using high-slew-rate precision operational amplifiers. Laser trimming improves resistor matching and gain accuracy, while matched resistor temperature coefficients help preserve common-mode rejection and gain accuracy over temperature. The dual-channel implementation reduces package count when two independent differential measurements are required. Typical uses include current-sense and low-voltage bridge measurements, industrial sensor interfaces, communications-line signal conditioning, precision test equipment, and differential inputs to data converters. The 1.5 MHz bandwidth is particularly useful when the measured differential signal must be captured without the long settling delays associated with lower-bandwidth instrumentation amplifiers. The 450 µV offset specification should nevertheless be evaluated against the smallest signal amplitude that the application expects to measure. When designing around the INA2133U, check input common-mode range, output swing, supply voltage, gain configuration, and the input/output network required by the selected operating mode. Place the device close to the signal source, maintain short differential traces, and use a quiet return path so that connector or routing noise does not degrade the differential measurement. Decoupling capacitors should be positioned at the supply pins according to the manufacturer application guidance. This page combines the verified manufacturer specifications, current distributor availability, same-family drop-in options, application guidance, and practical design notes. It also distinguishes verified INA2133U characteristics from parameters that still require confirmation from the complete manufacturer datasheet or application-specific calculations.

見積もり お問い合わせ
INA2133UA - Dual 1.5MHz Difference Amplifier | Texas Instruments
INA2133UA

INA2133UA - Dual 1.5MHz Difference Amplifier | Texas Instruments

Texas Instruments INA2133UA is a dual, unity-gain precision difference amplifier with 1.5 MHz bandwidth, 450 µV maximum offset voltage, and approximately 0.95 mA power consumption. The device is supplied in a 14-pin SOIC package and is intended for measuring small differential signals in the presence of large common-mode voltages. Its two amplifier channels support independent differential measurements when board space, power, and signal conditioning requirements favor integration. A difference amplifier is a specialized amplifier IC that subtracts two input voltages and amplifies the resulting differential signal. Its internal resistor network establishes the gain and improves common-mode rejection when the paired resistors track closely over temperature. The INA2133 belongs to the difference-amplifier hierarchy, where precision difference amplifier is a subtype of instrumentation amplifier and analog signal-conditioning IC. The manufacturer describes the INA2133 as a high-speed, precision difference amplifier built from a precision operational amplifier and a laser-trimmed resistor network. The INA2133UA provides a maximum input offset voltage of 450 µV, low offset-voltage drift, and maximum gain error of 0.05%. Its 1.5 MHz bandwidth supports higher-frequency signal paths than a slow precision difference amplifier while retaining the gain accuracy required for bridge and sensor measurements. The integrated resistor network is designed for accurate gain and high common-mode rejection. Excellent resistor temperature-coefficient tracking helps maintain gain accuracy and common-mode rejection over temperature. The dual configuration allows two matched differential channels in one package, reducing board area compared with two separate single-channel devices. The manufacturer also offers the related INA133 family in the same high-speed precision difference-amplifier datasheet. Typical uses include bridge-transducer signal extraction, differential sensor measurement, current-shunt monitoring, instrumentation, and factory-automation signal conditioning. The device is particularly suitable when a small differential voltage must be measured in the presence of a larger common-mode voltage and when a unity-gain difference-amplifier implementation would otherwise require several passive and active components. Design the input network, output reference, supply bypassing, and grounding to preserve common-mode rejection and bandwidth. Keep input and feedback routes compact, place bypass capacitors close to the supply pins, and use a low-noise reference for applications that require an output referenced to ground or another system voltage. Confirm the complete pin assignment and operating limits against the manufacturer datasheet before layout release. This product page combines the manufacturer device description, package and ordering information, sourcing availability, strict drop-in alternative screening, and practical design guidance. It also distinguishes directly verifiable INA2133UA characteristics from parameters that require confirmation against the complete manufacturer datasheet before a new design is released.

見積もり お問い合わせ
INA2134PA - Dual 0dB Audio Differential Receiver | Texas Instruments
INA2134PA

INA2134PA - Dual 0dB Audio Differential Receiver | Texas Instruments

The Texas Instruments INA2134PA is a dual audio differential line receiver with a fixed gain of 1 V/V, low distortion of 0.0005% at 1 kHz, and a 14 V/µs slew rate. The device is supplied in a 14-pin PDIP package for through-hole audio and instrumentation designs. Each channel uses high-performance operational amplifiers with on-chip precision resistors to convert balanced differential inputs into single-ended audio signals. An audio differential line receiver is a specialized amplifier stage that rejects common-mode noise present on balanced signal pairs while preserving the wanted differential audio voltage. Its place in the signal-chain hierarchy is differential receiver → balanced audio input amplifier → analog signal-conditioning front end. This makes the INA2134PA particularly useful when a stereo source uses balanced left and right channels but the downstream circuitry requires ground-referenced, single-ended audio signals. Key performance characteristics include a fixed 0 dB voltage gain, 90 dB minimum CMRR, 2.9 mA maximum quiescent current, and operation from -18 V to +18 V. According to the TI INA134 and INA2134 datasheet, the receiver combines low distortion with fast settling and wide output-voltage swing. The 14 V/µs slew rate supports accurate reproduction of high-level, high-frequency transients rather than clipping them under moderate loading. The INA2134PA contains two independent receiver channels and internal precision gain-setting resistors. On-chip resistors reduce component count and help maintain consistent channel-to-channel gain without requiring external matched networks. Its differential architecture is useful for rejecting ground-potential differences and coupled interference present between a source and the receiving equipment, especially in professional audio, instrumentation, and industrial control systems. Typical uses include stereo balanced-to-unbalanced conversion, audio measurement front ends, line-level signal conditioning, and instrumentation amplifiers. Because the gain is fixed at 1 V/V, downstream stages must provide any required attenuation or additional amplification. The device is also appropriate for prototypes, repairs, and legacy equipment where a standard 14-pin PDIP footprint and through-hole assembly are preferred over a surface-mount package. When laying out the receiver, connect the balanced input conductors to their assigned differential inputs and route the outputs to the following analog stage with short traces and a stable ground reference. Decouple each supply rail close to the device, keep input and output nodes away from switching-current paths, and verify the output swing against the selected load. This page also organizes package, electrical, and replacement information for faster component selection.

見積もり お問い合わせ
INA2134UA - 0dB Audio Differential Receiver | Texas Instruments
INA2134UA

INA2134UA - 0dB Audio Differential Receiver | Texas Instruments

The Texas Instruments INA2134UA is a dual-channel audio differential line receiver with a fixed 1 V/V gain, low distortion, and high slew rate, housed in a 14-pin SOIC package. The receiver is designed for professional audio and other balanced-signal applications where common-mode rejection and signal integrity are important. A differential receiver is an analog signal-conditioning circuit that accepts a pair of complementary or balanced inputs and produces a single output proportional to their difference. The INA2134 family uses high-performance operational amplifiers with on-chip precision resistors. This integrated approach simplifies balanced audio input design and reduces the need for external matched resistor networks. Its differential architecture is part of the broader special-purpose amplifier and signal-conditioning IC hierarchy. The INA2134UA provides 0.0005% distortion at 1 kHz, a 14 V/µs slew rate, and a fixed gain of 1 V/V. The manufacturer specifies a wide supply range of ±18 V and low quiescent current of 2.9 mA maximum. Its high common-mode rejection helps reject shared noise and interference on balanced audio lines, while fast settling and slew-rate performance support dynamic audio signals. The device is offered in single and dual versions, with INA2134UA providing two receiver channels. The 14-pin SOIC package provides a practical surface-mount option for balanced audio preamplifiers, mixer stages, instrument interfaces, and other low-frequency analog systems. The INA2134UA is also specified for operation from -40°C to +85°C, covering the extended industrial temperature range. When using the INA2134UA, preserve the balanced signal path and connect the appropriate input and output decoupling capacitors close to the device pins. Verify source impedance, output loading, cable termination, and common-mode voltage before finalizing the analog layout. Proper grounding and symmetrical routing are important for maximizing common-mode rejection and minimizing distortion. This product page combines the manufacturer specifications, sourcing guidance, drop-in alternatives, application fit, and practical PCB considerations to support faster component selection and design review. It is intended to help engineers identify the correct package, compare suitable alternatives, and implement a stable balanced-audio front end without treating the receiver as a general-purpose precision amplifier.

見積もり お問い合わせ
INA2137UA - Dual ±6dB Audio Receiver | Texas Instruments
INA2137UA

INA2137UA - Dual ±6dB Audio Receiver | Texas Instruments

The Texas Instruments INA2137UA is a dual audio differential line receiver with selectable fixed gains of +6 dB and -6 dB, a 14-pin SOIC package, and operation from dual ±18 V supplies. It combines high-performance operational amplifiers with on-chip precision resistors to recover balanced audio signals and reject common-mode interference. An audio differential line receiver is a specialized analog interface that converts a balanced, differential input into a single-ended audio signal. Its functional position is input conditioning: line receiver, differential receiver, analog signal conditioner, and interface IC. Differential reception is particularly useful when two conductors carry the same signal in opposite polarity, allowing common-mode noise to be rejected before the signal reaches an audio-processing or amplification stage. Key features include low distortion of 0.0005% at 1 kHz, a slew rate of 14 V/µs, a fast settling time of 0.01%, and high common-mode rejection of 90 dB. The maximum quiescent current is 2.9 mA, while the wide ±18 V supply range supports conventional professional and consumer audio rails. Each receiver can provide a fixed gain of 1/2 or 2, corresponding to -6 dB or +6 dB. The internal precision-resistor network provides repeatable gain without requiring external gain-setting resistors. This simplifies board design and reduces tolerance-related gain errors. High slew rate preserves large-signal dynamic range in music and speech paths, while low distortion minimizes added harmonic content. The 90 dB CMRR specification helps attenuate hum and interference picked up equally by both input conductors. Typical applications include balanced professional-audio inputs, consumer audio equipment, active speaker systems, audio mixers, and instrumentation interfaces. The dual-channel configuration accommodates left and right channels in one package. The 14-pin SOIC also offers a practical standard footprint for through-hole assembly and conventional surface-mount production. When designing a board around the INA2137UA, preserve the balanced input topology and keep input and return paths appropriately routed. Check output swing, input common-mode range, and gain configuration against the intended signal amplitude. Decoupling capacitors should be placed close to the supply pins, while unused inputs require appropriate treatment according to the manufacturer pin-description table. This product overview combines the device's audio-performance figures, package information, pin and footprint considerations, replacement guidance, and application-level design guidance to support faster component evaluation and board-level implementation.

見積もり お問い合わせ
INA213BQDCKRQ1 - 26V Bidirectional Current-Sense IC | TI
INA213BQDCKRQ1

INA213BQDCKRQ1 - 26V Bidirectional Current-Sense IC | TI

The Texas Instruments INA213BQDCKRQ1 is an AEC-Q100 automotive-grade, voltage-output, bidirectional current-shunt monitor rated for common-mode voltages from -0.3V to 26V, packaged in a 6-pin SC-70 DCK package. The device is designed to amplify the small differential voltage produced across a current-sense shunt and convert it into a ground-referenced analog voltage for measurement and control. A current-sense amplifier, also called a current-shunt monitor, is a specialized instrumentation amplifier that measures current indirectly from the voltage drop across a precision shunt resistor. INA213-Q1 belongs to the voltage-output current-shunt-monitor family within instrumentation amplifiers and power-measurement ICs. Its bidirectional measurement supports both positive and negative current flow, making it suitable for motor, battery, automotive, and industrial power-control systems. Verified manufacturer and distributor data identify the INA213BQDCKRQ1 as a 26V, AEC-Q100, high-precision current-sense amplifier. The device supports low-side or high-side measurement, and the official part page identifies the DCK package as a 6-pin SOT-SC70 package. The automotive-grade ordering suffix is consistent with the AEC-Q100 qualification stated by Texas Instruments. The INA21x-Q1 family is intended for applications requiring accurate current measurement across a shunt while the sensed node may sit at a substantially different voltage from the measurement ground. This allows current monitoring in batteries, motor-control systems, electronic loads, power supplies, and automotive electrical systems without placing the shunt at ground potential. The output voltage must remain within the device's valid operating and output limits, so the system designer should verify supply, common-mode, shunt, and output-headroom constraints from the manufacturer datasheet. Typical uses include bidirectional battery-current measurement, DC motor current sensing, solenoid and actuator monitoring, power-supply load current reporting, industrial control input sensing, and automotive load diagnostics. Because the part is bidirectional, it can report charge and discharge current with one signal path rather than requiring separate positive and negative measurement channels. The primary design consideration is the relationship between shunt resistance, sensed current, amplifier gain, input range, and output swing. A higher shunt resistance produces a larger differential signal and can improve measurement resolution, but it also increases power dissipation in the shunt. The PCB should keep the high-current shunt path separate from sensitive input traces, use a low-error reference resistor network, and provide stable supply bypassing close to the device. This page combines verified source data with engineering guidance while clearly identifying parameters that require confirmation from the manufacturer datasheet.

見積もり お問い合わせ
INA2141P - Dual G=10/100 Instrumentation Amplifier | Texas Instruments
INA2141P

INA2141P - Dual G=10/100 Instrumentation Amplifier | Texas Instruments

The Texas Instruments INA2141P is a dual, low-power instrumentation amplifier offering selectable gains of 10 and 100 in a 16-pin plastic DIP package. Each amplifier combines low offset voltage, low drift, high common-mode rejection, current-feedback input circuitry, and wide bandwidth for precision analog signal conditioning. The INA2141P is designed for applications that require accurate amplification of differential signals in the presence of substantial common-mode voltage. An instrumentation amplifier is a specialized analog amplifier optimized for measuring low-level differential signals, such as sensor outputs, while rejecting common-mode noise and voltage. Unlike a general-purpose operational amplifier, an instrumentation amplifier provides high input impedance, consistent gain accuracy, and strong common-mode rejection in a single integrated circuit. The INA2141 family is a dual instrumentation amplifier, so one package can process two independent channels. The INA2141P supports two fixed gain settings, 10 and 100, and uses current-feedback input circuitry to maintain bandwidth at higher gain. The manufacturer datasheet states that bandwidth reaches 200 kHz at a gain of 100. Low offset voltage is specified at 50 µV maximum, with maximum drift of 0.5 µV/°C and gain accuracy of ±0.05%. Common-mode rejection reaches 117 dB minimum at a gain of 100. The device accepts supply voltages as low as ±2.25 V and operates with supplies up to ±18 V. Input protection extends to ±40 V, helping the amplifier withstand overload conditions in sensor interfaces and industrial measurement systems. Quiescent current is approximately 750 µA per amplifier, making the device suitable for low-power and battery-operated instrumentation. Typical uses include bridge-sensor and pressure-transducer interfaces, medical monitoring, industrial process measurement, current-loop sensing, and laboratory instrumentation. Because the INA2141P is a dual amplifier, it is especially useful for paired sensors or two-stage measurement systems where board area and power consumption are important. Designers should verify the gain-setting resistor configuration, reference-voltage implementation, input common-mode range, and supply headroom against the datasheet before layout. Decoupling capacitors should be placed close to the supply pins, and the analog input traces should be routed away from switching nodes. The manufacturer datasheet also provides application guidance for gain selection, bandwidth, and input protection. This page combines the verified manufacturer and distributor information for INA2141P with package-level guidance, application context, and design considerations that help engineers evaluate the device alongside alternative instrumentation-amplifier implementations.

見積もり お問い合わせ
INA2141U - Dual 100V/µs Instrumentation Amplifier | Texas Instruments
INA2141U

INA2141U - Dual 100V/µs Instrumentation Amplifier | Texas Instruments

The Texas Instruments INA2141U is a dual-channel, low-power instrumentation amplifier with selectable gains of 10 and 100, 4 V/µs slew rate, and 1 MHz gain-bandwidth product, housed in a 16-pin SOIC (DW) package. Each channel offers a maximum input offset voltage of 50 µV, maximum offset drift of 0.5 µV/°C, and typical gain accuracy of ±0.05%. The devices support bipolar supplies up to ±18 V and include input protection to ±40 V. An instrumentation amplifier is a precision analog signal-conditioning IC that amplifies the differential voltage between two inputs while rejecting common-mode interference. Its internal architecture provides high input impedance, accurate resistor-based gain, and strong common-mode rejection. In the electronic-component hierarchy, the INA2141U is a dual instrumentation amplifier within the broader amplifier IC and signal-conditioning categories. Key features include a low maximum input bias current of 5 nA and a minimum common-mode rejection ratio of 117 dB. These characteristics suit sensor interfaces where source impedance, thermocouple voltages, and small bridge signals must be measured accurately. The low-power design also supports battery-powered instrumentation and compact test equipment where amplifier efficiency and low bias current influence overall system error. The internal gain architecture offers a choice of 10 or 100 to match both moderate and high-sensitivity measurement ranges. A 1 MHz gain-bandwidth product supports signal bandwidth required by many industrial, medical, and laboratory systems, while the 4 V/µs slew rate improves large-signal response. Maximum input offset voltage of 50 µV and drift of 0.5 µV/°C limit errors in low-level DC measurements. Typical uses include bridge excitation and readout, pressure and strain-gauge amplification, biopotential front ends, battery-powered sensor modules, current-shunt measurements, and precision data-acquisition systems. The 16-pin SOIC package allows conventional surface-mount assembly, while the dual-channel configuration can reduce board area when two differential inputs must be conditioned. Designers should use the manufacturer pin-description table to assign input, feedback, reference, power, and output connections. Input filtering, reference-grounding, and supply-bypass placement require care because parasitic resistance can degrade CMRR and offset performance. Input protection ratings should not be interpreted as a substitute for external surge protection in hazardous or high-energy systems. This page consolidates the key INA2141U specifications, verified package information, application guidance, and confirmed replacement references into a practical engineering comparison. It also distinguishes direct pin-compatible options from related INA214x devices whose gain and channel characteristics differ.

見積もり お問い合わせ
INA2143U - 5-V/µs Dual Precision Difference Amplifier | TI
INA2143U

INA2143U - 5-V/µs Dual Precision Difference Amplifier | TI

The Texas Instruments INA2143U is a dual high-speed precision difference amplifier featuring 5 V/µs slew rate, 250 µV offset, selectable gain settings of 10 or 0.1, and a 14-pin SOIC package. The device is intended for systems that measure small voltage differences and require amplified differential outputs. A difference amplifier is a specialized operational-amplifier circuit that compares voltages applied to its inverting and non-inverting inputs and amplifies the voltage between them. This method helps reject signals that appear equally on both inputs, making difference amplifiers useful within measurement, instrumentation, analog-control, and signal-conditioning systems. The INA2143U belongs to the amplifier IC category and combines two precision difference amplifiers in one package. Key features include a 5 V/µs slew rate, 250 µV offset, gain options of 10 and 0.1, dual-channel operation, and an operating temperature range of -55°C to 125°C. The 5 V/µs slew rate allows the output to respond quickly to input-voltage changes, while the selectable gain provides flexibility for different differential-signal levels. Each channel can support the two stated gain configurations. The INA2143U combines two difference amplifiers in a single 14-pin SOIC (D) package, reducing board area when two differential channels are required. Its high-speed and precision positioning makes it applicable to fast analog signal conditioning, where the main design objective is to preserve the relationship between two input voltages while converting the differential signal into a single-ended output. Typical applications include current-sense amplifier front ends, differential sensor interfaces, bridge-based measurement circuits, industrial instrumentation, and analog control systems. In a current-sense design, the amplifier processes the voltage generated across a sense resistor rather than the full supply voltage. In a bridge or differential sensor interface, it rejects common-mode voltage and preserves the smaller differential component being measured. Designers should use the manufacturer pin-description table when assigning traces and power connections, and they should verify signal amplitudes against the selected gain of 10 or 0.1. PCB placement should minimize resistive and capacitive pickup around the differential inputs, while supply bypassing should follow the connection and capacitor recommendations in the manufacturer datasheet. This page combines the confirmed INA2143U operating characteristics with practical selection guidance, application context, package information, and drop-in replacement validation. It distinguishes confirmed device attributes from parameters that require confirmation from the complete manufacturer datasheet, helping engineers plan sourcing and circuit design with fewer assumption-driven steps.

見積もり お問い合わせ
INA217AIP - Low-Noise Instrumentation Amplifier | Texas Instruments
INA217AIP

INA217AIP - Low-Noise Instrumentation Amplifier | Texas Instruments

The Texas Instruments INA217AIP is a low-noise, low-distortion monolithic instrumentation amplifier in an 8-pin PDIP package. It accepts a 4.5 V to 18 V supply, provides a typical gain of 3 V/V, features 250 µV input offset voltage, and supports a slew rate of 15 V/µs with 3.4 MHz bandwidth. An instrumentation amplifier is a specialized amplifier optimized for measuring low-level differential signals. Its internal signal path rejects common-mode noise while amplifying the voltage difference between two inputs. The INA217 belongs to the instrumentation amplifier, differential amplifier, analog amplifier, and signal-conditioning IC hierarchy, making it suitable for precision sensor conditioning, balanced audio, industrial measurement, and medical instrumentation. The device uses current-feedback circuitry to provide wide bandwidth and strong dynamic response over a broad gain range. Its distortion-cancellation architecture is intended to maintain low distortion even at higher gain. The manufacturer identifies near-theoretical noise performance for a 200 Ω source impedance, making balanced low-impedance microphone signals a primary use case. The monolithic implementation also provides differential inputs, low noise, and low distortion in one package. INA217AIP is identified as a replacement for the SSM2017 and is available with the same DIP-8 and wide-body SOL-16 pin arrangements. The DIP-8 format is useful when an existing instrument-amplifier layout must be retained. Its 15 V/µs slew rate supports high-level audio stages, while differential input handling improves rejection of common-mode interference in measurement systems. Typical applications include professional microphone preamplification, low-level bridge or transducer signal conditioning, industrial process measurement, and medical monitoring. In a microphone circuit, the part processes the differential output of a balanced capsule while rejecting much of the shared noise appearing on both signal conductors. Its low-noise, low-distortion characteristics help preserve the signal-to-noise ratio of the source. When designing around INA217AIP, preserve the pin arrangement of the original SSM2017 layout and follow the manufacturer datasheet for gain-setting resistors, supply bypass capacitors, and output drive requirements. Check input common-mode range, output swing, and source impedance at the selected gain because instrumentation amplifiers can become input-voltage-range constrained even when their bandwidth remains adequate. This product page combines the manufacturer electrical description, package information, compatible-device context, and application-level engineering guidance. It also distinguishes direct replacements from alternatives that require different packages, helping designers evaluate PCB reuse, signal bandwidth, and noise performance before committing to a component.

見積もり お問い合わせ
INA2181 26V Dual-Channel Current Sense Amp | TI | Gain 20 V/V
INA2181A1IDGSR

INA2181 26V Dual-Channel Current Sense Amp | TI | Gain 20 V/V

The Texas Instruments INA2181 (e.g., INA2181A1IDGSR) is a 26V, dual-channel, bidirectional, 350kHz voltage-output current sense amplifier in a 10-pin VSSOP (DGS) package, part of the cost-optimized INAx181 family. It senses voltage drops across shunt resistors on low- or high-side rails and outputs a ground-referenced analog voltage proportional to load current. A current sense amplifier (also called a current-shunt monitor) is a specialized difference amplifier that extracts a small differential shunt voltage riding on a large common-mode voltage and converts it to a ground-referenced single-ended signal. Within the signal chain hierarchy it sits between the shunt resistor and an ADC or comparator, serving as a front-end element of power management and battery monitoring systems. Key features include a wide 2.7V to 26V common-mode range that is independent of the 2.7V to 5.5V supply, 350kHz bandwidth for fast load-transient monitoring, bidirectional operation with a reference pin for charging/discharging current measurement, and factory-calibrated gain options (A1 = 20 V/V, A2 = 50 V/V, A3 = 100 V/V, A4 = 500 V/V) that eliminate gain-setting resistors. The zero-drift architecture delivers low offset for small shunt voltages. The dual channels share one package, halving board area versus two single-channel monitors such as the INA181. Rail-to-rail output swings close to the supply rails, maximizing ADC dynamic range. All device options are specified from -40C to +125C. Typical applications include battery current monitoring in portable and industrial equipment, DC motor drive phase and bus current sensing, telecom and server power supply current telemetry, and load-current supervision in 12V/24V rails feeding TI C2000 or MSPM0 MCUs. Design tip: keep the shunt voltage in the 10 mV to 100 mV range at full load - large enough to swamp offset error, small enough to limit shunt power dissipation. Route Kelvin sense traces directly to the shunt pads to preserve accuracy.

見積もり お問い合わせ