集積回路

サブカテゴリ

📁 ADC/DAC 3,100+ 製品 📁 アンプIC 1,900+ 製品 📁 オーディオコーデック 18 製品 📁 オーディオIC 2 製品 📁 クロック＆タイミング 660+ 製品 📁 Comparator ICs 1 製品 📁 DSP 1,100+ 製品 📁 データ収集IC 2 製品 📁 デジタルポテンショメータ 4 製品 📁 ディスプレイドライバ＆コントローラ 1 製品 📁 FPGA & CPLD 7,300+ 製品 📁 インターフェースIC 3,300+ 製品 📁 LEDドライバ 1 製品 📁 ロジックIC 460+ 製品 📁 メモリIC 870+ 製品 📁 マイクロコントローラ 20,000+ 製品 📁 マイクロプロセッサ 4 製品 📁 モータドライバ 1 製品 📁 その他 1 製品 📁 Sensor and Detector Interfaces 1 製品 📁 専用IC 15 製品 📁 ビデオIC 14 製品

製品 (39,000+)

LT1639IS - 1.2MHz Micropower Rail-to-Rail Op Amp | Analog Devices
LT1639IS

LT1639IS - 1.2MHz Micropower Rail-to-Rail Op Amp | Analog Devices

The Analog Devices LT1639IS is a low-power quad operational amplifier with rail-to-rail input and output capability, 1.2 MHz gain-bandwidth product, and 0.4 V/us slew rate. The device is supplied in a 14-pin surface-mount SO package and is designed for compact, low-voltage analog signal-conditioning systems. An operational amplifier is an active semiconductor component that uses external feedback to amplify voltage differences. The LT1639 belongs to the precision operational-amplifier family, combining low quiescent-current operation with over-the-top input and output capability. This makes it useful when the signal can move close to either supply rail while the circuit must remain compact and power efficient. The LT1639IS provides four amplifier channels in one 14-pin package. Its rail-to-rail input stage supports signal ranges near the positive and negative supply rails, while the rail-to-rail output stage improves output swing flexibility. The 1.2 MHz unity-gain bandwidth is suitable for low-frequency instrumentation, sensor interfaces, audio support circuits, buffer stages, and general-purpose analog signal conditioning. The 0.4 V/us slew rate supports moderate-amplitude signal transitions without requiring a high-speed amplifier. Because the LT1639 is intended for low-power applications, circuit design should account for supply voltage, load current, input common-mode range, output swing, noise, and stability. The SO package requires appropriate PCB land patterns and adequate thermal pathways when several channels operate continuously. Decoupling capacitors should be placed close to the supply pins, and feedback networks should be selected to preserve stability across the intended gain and load conditions. Typical uses include battery-powered sensing, low-voltage instrumentation, audio preamplification, analog filtering, ADC or DAC interface buffering, and portable measurement equipment. Its four-channel configuration reduces board area compared with separate single or dual amplifiers when the same amplifier family is used throughout a design. This product page combines the manufacturer product information, technical descriptions, package data, and practical design guidance into a focused reference for engineers evaluating the LT1639IS. It also records the available sourcing channel and identifies replacement candidates only when the package and functional requirements remain compatible.

見積もり お問い合わせ
LT1711CMS8#PBF - 4.5ns Rail-to-Rail Comparator | Analog Devices
LT1711CMS8#PBF

LT1711CMS8#PBF - 4.5ns Rail-to-Rail Comparator | Analog Devices

The Analog Devices LT1711CMS8#PBF is a single-channel UltraFast 4.5 ns comparator featuring rail-to-rail inputs, rail-to-rail complementary outputs and an output latch, packaged in an 8-pin MSOP (CMS8). It is specified over a single supply range of 2.4 V to 12 V (or dual supply ±2.4 V to ±6 V), drawing 17 mA typical quiescent supply current, and provides CMOS/TTL-compatible complementary outputs. A high-speed comparator is an analog building block that compares two input voltages and switches its output to a digital logic level as soon as the difference crosses zero. Within the broader component taxonomy, the LT1711 sits at the intersection of linear analog (high-speed input stage with rail-to-rail common-mode) and digital logic (latched complementary outputs). Its place in the signal chain is right at the boundary between the analog domain and the digital domain, where decisions must be made quickly and unambiguously - for example between a sensor front-end and an FPGA capture register. Three specifications define the part's character: a 4.5 ns propagation delay at 20 mV overdrive, rail-to-rail input common-mode range that accepts signals at both supply rails, and a built-in latch pin that allows the output state to be held transparent or frozen on command. The complementary outputs reduce external inversion logic, and TTL/CMOS compatibility lets the part drive either 3.3 V or 5 V logic without level shifters. The latch enables pipelined architectures where a high-to-low transition must be frozen while downstream logic processes a previous event. Internally, the LT1711 uses a high-speed differential input pair followed by a positive-feedback latch stage and complementary CMOS output drivers. The 4.5 ns figure is achieved at 20 mV overdrive; at 5 mV overdrive the delay increases modestly because the input stage must slew further through its linear region. The MSOP-8 package with exposed pad (when present on the same die family) keeps the thermal loop short and allows tight PCB layout for high-speed analog. Typical applications include high-speed instrumentation triggers, time-of-flight and LIDAR threshold detectors, line receivers and signal restoration in noisy backplane links, motor control current-sense zero-cross detection, and clock/data recovery decision circuits. The wide supply range makes it useful in both 3.3 V and 5 V systems. When designing with this part, place decoupling capacitors as close as possible to V+ and V- and keep input trace lengths short; the latch pin must be held low during the active compare window and pulsed high only when freezing the output is required.

見積もり お問い合わせ
LT1711CMS8#TRPBF - 4.5ns Rail-to-Rail Comparator w/ Latch | ADI | MSOP-8
LT1711CMS8#TRPBF

LT1711CMS8#TRPBF - 4.5ns Rail-to-Rail Comparator w/ Latch | ADI | MSOP-8

The Analog Devices LT1711CMS8#TRPBF is a 4.5ns UltraFast comparator featuring rail-to-rail inputs, rail-to-rail complementary outputs (TTL/CMOS compatible) and an internal output latch, housed in an 8-pin MSOP package. It is optimized for 3V and 5V power supplies and operates from a single supply of 2.4V to 12V or from dual supplies of ±2.4V to ±6V. A comparator (also called a voltage comparator) is a device that compares two analog input voltages and produces a binary digital output indicating which input is larger. It is the fundamental building block at the boundary between the analog and digital domains, used in level detection, threshold sensing, line receivers, peak detectors, clock-recovery circuits, and ADC front-ends. Comparators such as the LT1711 sit within the broader analog IC hierarchy as signal-conditioning ICs that bridge linear analog signal paths and high-speed digital logic families. Key specifications include a 4.5ns propagation delay at 20mV overdrive, 7ns at 5mV overdrive, 1.5mV maximum input offset voltage, and ±10mA output drive current. The output latch retains data when the LATCH pin is held high, with internal hysteresis to reject slow or noisy latch signals. Inputs can exceed the supply rails without phase reversal, which simplifies interfacing with bipolar sensor signals that swing beyond VCC. Architecturally, the LT1711 uses complementary N-channel/P-channel differential input stages to achieve true rail-to-rail input common-mode range, followed by a regenerative latch core that delivers sub-5ns decision times. The TTL/CMOS-compatible complementary outputs eliminate the need for an external level translator when driving 3.3V or 5V FPGAs, ASICs, or microcontrollers. Typical applications include high-speed automatic test equipment (ATE), window comparators for line receivers, peak/zero-crossing detectors, clock-recovery circuits, threshold detectors in instrumentation, fast analog-to-digital converter front-ends, and pulse-width measurement systems. The wide input range and latch function make it equally suited to single-supply battery-powered designs and split-rail industrial signal chains. When designing with the LT1711, place a 0.1µF bypass capacitor as close as possible to the supply pin and minimize input trace lengths to avoid coupling transients into the high-impedance differential pair. For sub-2ns edge fidelity, use a controlled-impedance output trace terminated at the destination logic input. The output latch pin should be tied low when unused, never left floating. This page synthesizes distributor pricing, drop-in alternatives in the same 8-MSOP footprint, and practical design notes not found in the manufacturer datasheet.

見積もり お問い合わせ
LT1797CS5#TRMPBF - 10MHz Rail-to-Rail Op Amp | Analog Devices
LT1797CS5#TRMPBF

LT1797CS5#TRMPBF - 10MHz Rail-to-Rail Op Amp | Analog Devices

The LT1797CS5#TRMPBF is a unity-gain stable 10MHz operational amplifier from Analog Devices, housed in a compact 5-lead TSOT-23 package. It operates on all single and split supplies with a total voltage range of 2.7V to 12V, drawing only 1mA of quiescent current. The amplifier features rail-to-rail input and output, making it ideal for current sensing and other single-supply applications. An operational amplifier (op amp) is a high-gain voltage amplifier with differential inputs and a single-ended output. It is a fundamental building block in analog electronics, used in signal conditioning, filtering, and buffering. The LT1797 belongs to the class of general-purpose op amps, which are versatile components found in a wide range of applications from consumer electronics to industrial instrumentation. Key features of the LT1797 include a slew rate of 2.25V/μs, a gain-bandwidth product of 10MHz, and an input common-mode range that includes both rails. The input stage incorporates phase reversal protection, ensuring robust operation. The device is specified for the commercial temperature range of 0°C to 70°C, and the CS5 suffix indicates the SOT-23 package with lead-free finish. The LT1797 uses a bipolar process technology that provides low offset voltage and low noise, making it suitable for precision applications. The rail-to-rail input and output capability allows maximum dynamic range in low-voltage single-supply designs. The low quiescent current of 1mA makes it ideal for battery-powered portable devices. Typical applications include current sensing, portable instrumentation, battery-powered systems, and signal conditioning in industrial and automotive environments. The small TSOT-23 package saves board space, and the wide supply range allows operation from a single 3V or 5V supply or dual ±5V supplies. When designing with the LT1797, ensure proper decoupling of the power supply pins with 0.1μF ceramic capacitors placed close to the device. The rail-to-rail input stage requires attention to common-mode voltage limits to avoid phase reversal, although the device includes internal protection.

見積もり お問い合わせ
LT1801CDD - Dual 80MHz Rail-to-Rail Op Amp | Analog Devices
LT1801CDD

LT1801CDD - Dual 80MHz Rail-to-Rail Op Amp | Analog Devices

The Analog Devices LT1801CDD is a dual-channel, low-power, high-speed rail-to-rail input and output operational amplifier housed in an 8-pin DFN (3x3 mm) package with exposed pad. It delivers a gain-bandwidth product of 80 MHz and a slew rate of 25 V/us from a reduced supply current of approximately 2 mA per amplifier, making it well suited for portable, battery-powered and high-density PCB designs where both DC precision and AC speed are required. Background knowledge: an operational amplifier (op amp) is a DC-coupled, high-gain electronic voltage amplifier with differential inputs and a single-ended output that forms the basic building block of analog signal conditioning. Op amps sit within the broader hierarchy of linear integrated circuits -> amplifiers -> operational amplifiers. Rail-to-rail variants extend the input common-mode and output swing to within millivolts of each supply rail, removing the headroom loss of older single-supply designs and enabling full use of low-voltage ADC input ranges. Key features of the LT1801 include a low input offset voltage, low input bias current, rail-to-rail input and output swing, 25 V/us slew rate, 80 MHz gain-bandwidth product, and stable operation on supplies from 2.5 V to 12.6 V (single or dual). The exposed-pad DFN-8 package offers an exposed thermal pad that lowers theta_JA versus an SOIC-8 alternative, helping the part handle momentary short-circuit loads without thermal shutdown in space-constrained layouts. Architecturally, the LT1801 uses a complementary input stage that combines N-channel and P-channel differential pairs so the common-mode input range reaches both rails without crossover distortion at mid-supply. The output stage is a class AB rail-to-rail design that maintains low quiescent current while sourcing or sinking transient load currents required by the 25 V/us slew rate into 100 pF or more of cable capacitance. Typical applications include active filters, precision integrators, photodiode transimpedance amplifiers, ADC input buffers, DAC output buffers, portable instrumentation, and battery-powered signal-chain front ends. Design considerations focus on the exposed pad requiring solder connection to a ground copper pour for rated thermal performance, and the rail-to-rail input stage's slightly higher input bias current near the rails, which matters for very-high-impedance sensor interfaces.

見積もり お問い合わせ
LT1805CS - 85MHz Quad Rail-to-Rail Op Amp | Analog Devices
LT1805CS

LT1805CS - 85MHz Quad Rail-to-Rail Op Amp | Analog Devices

Analog Devices LT1805CS is a high-speed, low-power, quad operational amplifier with 85 MHz gain bandwidth, 100 V/µs slew rate, and rail-to-rail input and output operation in a 14-pin SOIC package. Its low 1 mA maximum quiescent current supports the LT1805 family’s combination of wide bandwidth and reduced supply consumption. An operational amplifier is an analog integrated circuit that amplifies the voltage difference between its inverting and non-inverting inputs. The LT1805 belongs to the operational-amplifier hierarchy, where rail-to-rail input and output capability allows operation close to the supply rails. This makes the device useful in signal chains requiring high speed, wide common-mode range, and flexible output swing. Principal features include an 85 MHz gain-bandwidth product, a 100 V/µs slew rate, a 120 MHz −3 dB frequency at unity gain, and 4.2 nV/√Hz broadband input voltage noise. The quad configuration integrates four amplifiers into one 14-pin SOIC, allowing multiple gain stages or differential channels to share a compact footprint while preserving consistent device characteristics. The LT1805 family is designed for low-power, high-speed analog signal processing. Rail-to-rail input operation extends the usable input range toward the positive and negative supply rails, while rail-to-rail output provides improved output swing for downstream circuits. Its high slew rate supports rapid signal transitions, although stability, load capability, and output-current limits must be evaluated against the intended operating conditions. Typical applications include low-level signal conditioning, instrumentation front ends, active filtering, data-acquisition channels, sensor amplification, and high-speed buffer stages. The quad organization is particularly useful when a system requires several amplifiers, such as instrumentation amplifiers, multichannel sensor interfaces, or gain stages distributed across an analog board. Design with the LT1805CS by confirming supply voltage, input and output common-mode limits, capacitive-load stability, and noise performance for every signal range. Place bypass capacitors close to the supply pins, keep sensitive input traces short, and account for the PCB’s ground return when evaluating noise. The manufacturer datasheet should guide the final compensation, grounding, and application-circuit choices. This product page combines the family-level operating characteristics, package information, application guidance, and sourcing workflow for the LT1805CS. It also distinguishes the exact orderable variants from broader LT1805 options so engineers can identify whether a proposed replacement preserves the required amplifier count, package, and electrical behavior.

見積もり お問い合わせ
LT1882IS - Quad Picoamp Input Precision Op Amp | ADI
LT1882IS

LT1882IS - Quad Picoamp Input Precision Op Amp | ADI

Analog Devices LT1882IS is a four-circuit, rail-to-rail output precision operational amplifier with picoamp-class input bias current, a 1 MHz gain-bandwidth product, and a 0.4 V/µs slew rate. The device is packaged in a 14-pin SOIC and operates from single 2.7 V to 36 V supplies or dual ±18 V supplies. Its input offset voltage is trimmed below 50 µV, making it suitable for precision signal-conditioning systems that need low bias current, low offset, and rail-to-rail output swing. An operational amplifier, or op amp, is a high-gain analog building block used to amplify, buffer, filter, and compare small voltage signals. The LT1882 belongs to the precision operational amplifier category, which sits within analog ICs and broader semiconductor signal-conditioning systems. Its rail-to-rail output stage allows the output to approach the supply limits, while the picoamp input bias current reduces measurement errors when driving high-impedance sensors, photodiodes, and high-impedance feedback networks. Key features include four amplifiers in one package, a 1 MHz gain-bandwidth product, a 0.4 V/µs slew rate, input offset voltage trimmed to less than 50 µV, rail-to-rail output operation, and picoamp input bias current. These characteristics make the LT1882 particularly useful when a design requires precision DC behavior but does not need the higher speed of the LT1884 or LT1885. The manufacturer identifies thermocouple amplifiers, bridge-transducer conditioners, instrumentation amplifiers, battery-powered systems, and photodiode current amplifiers as representative applications. The LT1882 combines precision input characteristics with conservative speed and drive capability. Its lower bandwidth than the LT1884/LT1885 is intentional: reduced speed improves input-noise behavior, bias-current performance, and capacitive-load drive in exchange for slower slew and less bandwidth. Because all four channels share one package, designers can implement several gain stages, buffers, or active filters while controlling board area. Independent amplifiers can also be used for instrumentation front ends, although system-level offset and drift still require calibration when very high absolute accuracy is needed. Typical uses include thermocouple and low-level sensor conditioning, strain-gauge bridge signal amplification, precision current-to-voltage conversion for photodiodes, low-power instrumentation, and buffered sensor interfaces. In battery-powered equipment, the low input bias current can reduce demand on high-value precision resistors and sensitive transducers. The rail-to-rail output also improves usable signal swing in low-voltage systems, although headroom, output-current limits, and capacitive loading must be checked in the final operating condition. For PCB implementation, place each input and feedback component close to its associated amplifier pins, keep sensitive input traces short, and provide solid ground-plane continuity. Bypass the supply pins locally with the manufacturer-recommended ceramic capacitance. Avoid placing long parallel routes beneath sensitive amplifier inputs, because capacitive pickup can increase output noise or disturb bias-current measurements. Confirm output stability with the external load capacitance and feedback network used in the final circuit. This product page combines the manufacturer application positioning, package and performance characteristics, orderable-package details, and a focused replacement analysis. It also adds practical guidance for precision sensor interfaces, bridge conditioners, photodiode amplifiers, battery-powered systems, and instrumentation while clearly separating the LT1882 from higher-speed family members.

見積もり お問い合わせ
LT1885IS - Quad Precision Op Amp | Analog Devices
LT1885IS

LT1885IS - Quad Precision Op Amp | Analog Devices

Analog Devices LT1885IS is a four-circuit, precision operational amplifier with rail-to-rail output and picoamp-class input performance, offered in a 14-pin small-outline integrated-circuit package. The device combines input offset voltage trimmed below 50 µV with rail-to-rail output operation, making it suitable for instrumentation, sensor conditioning, and low-level signal-chain applications where accurate output swing and low input bias current are important. An operational amplifier, or op amp, is a high-gain differential amplifier used to amplify, buffer, filter, or control voltages. The LT1885 belongs to the precision operational-amplifier hierarchy, where input offset, input bias current, output swing, noise, and stability determine suitability for measurement systems. Its four amplifiers share one package while providing independent signal paths, reducing component count in multi-channel designs. The LT1885 family is designed for precision applications that benefit from rail-to-rail output operation. Rail-to-rail output allows the amplifier output to approach the available supply rails more closely than a conventional output stage, which can improve dynamic range in low-voltage systems. Picoamp-class input performance is particularly useful when measuring high-impedance sources because the amplifier contributes less input bias current to the measured node. According to the Analog Devices product information, the LT1884 and LT1885 op amps provide high-accuracy input performance while maintaining rail-to-rail output swing and faster response than other precision amplifiers. Input offset voltage is trimmed to less than 50 µV, supporting accurate conditioning of small differential signals. The LT1885IS contains four amplifiers, while the related LT1884 family is associated with dual-channel configurations. Typical uses include precision sensor interfaces, low-current measurement stages, current-to-voltage conversion, signal buffering, and multi-axis measurement systems. The four-channel organization is especially useful when four sensors require similar conditioning electronics or when symmetric analog channels are needed in an industrial, medical-instrumentation, or test-and-measurement system. Designers should verify supply voltage, input common-mode range, output swing under load, noise, gain-bandwidth product, and stability requirements against the manufacturer datasheet for the selected ordering code. Decoupling capacitors should be placed close to the supply pins, and sensitive high-impedance nodes should be protected from leakage, contamination, and electrostatic discharge. This product page organizes the LT1885IS family information with practical design considerations, qualified same-family alternatives, package details, and application guidance to support component selection and PCB planning.

見積もり お問い合わせ
LT1970AIFE#TRPBF - ±500mA Power Op Amp | Analog Devices
LT1970AIFE#TRPBF

LT1970AIFE#TRPBF - ±500mA Power Op Amp | Analog Devices

The Analog Devices LT1970AIFE#TRPBF is a ±500mA power operational amplifier with precise externally controlled current limiting, offered in a 20-pin TSSOP-EP package (5V to 36V supply range). It delivers independent 1%-accurate sourcing and sinking current limit thresholds via separate control voltages, and supports output current boosting through external power transistors. A power operational amplifier (power op amp) is a specialized high-current linear amplifier that combines the precision of a small-signal op amp with the drive capability of an output stage typically rated from hundreds of milliamps to several amps. Within the broader hierarchy, power op amps sit under operational amplifiers -> amplifiers -> analog ICs -> signal conditioning -> semiconductors. They are commonly used as programmable voltage or current sources, motor drivers, and audio amplifiers where a standard op amp cannot deliver sufficient load current. Key features include ±500mA minimum output current, 1.6 V/µs slew rate, independent adjustment of source and sink current limits, single or split supply operation from 5V to 36V total, and thermal shutdown. The exposed pad (TSSOP-EP) package provides a low thermal resistance path, which is critical for sustaining 500mA continuous output. The current-limit architecture uses two external programming voltages, enabling asymmetric sourcing and sinking limits for applications such as Class-AB audio or solenoid drive. Internally the LT1970A uses a bipolar output stage with a precision current-sense scheme that compares each external limit voltage against an internal VBE-referenced sense threshold. The 1% limit accuracy (improved from the LT1970's 2%) reduces output stage stress and enables tighter compliance envelopes in regulated current sources. Single-supply operation is supported by an internal charge pump, allowing the output to swing within a few hundred millivolts of each rail. Typical applications include programmable current sources, solenoid and valve drivers, audio amplifiers (Class A, B, AB), motor drivers, and transducer excitation. The TSSOP-EP footprint is well suited for compact industrial and instrumentation designs that require high current density on a small PCB. When designing with this part, dedicate a generous copper pour under the exposed pad to keep junction temperature within the 150°C absolute maximum. Decouple both supply rails close to the IC with 1µF X7R ceramics in parallel with 10µF bulk; the high output current makes supply-impedance-induced ringing a real concern. This page consolidates distributor pricing, drop-in same-package alternatives, application circuits, and PCB-level design notes that are not aggregated in the manufacturer datasheet alone.

見積もり お問い合わせ
LT1970IFE - ±500mA Power Op Amp | Analog Devices
LT1970IFE

LT1970IFE - ±500mA Power Op Amp | Analog Devices

The Analog Devices (formerly Linear Technology) LT1970IFE is a ±500 mA power operational amplifier with precise externally controlled current limiting, housed in a 20-pin TSSOP-EP (FE) package with an exposed thermal pad. It supports single or split supply operation from 5 V to 36 V total supply voltage and provides separate control voltages for sourcing and sinking current-limit sense thresholds with 2 % accuracy, enabling programmable bidirectional current limiting without external sense resistors. A power op amp is a specialized operational amplifier designed to deliver output power levels orders of magnitude greater than a conventional op amp. Unlike a small-signal op amp that typically sources or sinks tens of milliamps, a power op amp integrates output stages capable of hundreds of milliamps to several amps, often with thermal protection, current limiting, and short-circuit handling. Power op amps sit hierarchically between op amps and power management ICs, frequently replacing discrete driver + MOSFET combinations in programmable current sources, motor drivers, and audio line drivers. The LT1970 specifically combines power-output stages with adjustable precision current limiting, making it a single-chip alternative to discrete driver designs. Key features include ±500 mA minimum output current, 2 % accurate independent source and sink current-limit programming via external control voltages, the ability to boost output current by adding external power transistors, single or split supply operation from 5 V to 36 V, and thermal shutdown with the exposed pad for low thermal resistance. The output stage swings to within ±2.5 V of either supply rail at full current. The architecture uses a precision input stage followed by a high-current output stage with separate current-sense paths. The sourcing and sinking current limits are independently programmed by two DC control voltages on the ILIM+ and ILIM- pins, allowing asymmetric profiles for charging supercapacitors or driving inductive loads. External boost transistors can multiply output current beyond 500 mA while preserving the precision current-limit function. Typical applications include programmable current sources for LED drivers, solenoid and actuator drivers, motor torque drivers, headphone amplifiers, programmable power supplies, and battery chargers. The wide supply range makes the LT1970 particularly suited to industrial 24 V bus systems and automotive 12 V/24 V loads. When designing with this device, place a 1 µF bypass capacitor close to each supply pin and use the exposed pad for thermal dissipation. For applications above 500 mA, ensure the external boost transistors are mounted on a thermally adequate footprint and that the current-limit control voltages remain stable across the operating temperature range. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes for the LT1970IFE that complement the official datasheet by adding cross-source comparisons and PCB-level guidance.

見積もり お問い合わせ
LT311AN8 - 30V, 200ns Voltage Comparator | Analog Devices
LT311AN8

LT311AN8 - 30V, 200ns Voltage Comparator | Analog Devices

The Analog Devices LT311AN8 is a general-purpose, single voltage comparator with a 5V to 30V single-supply range, differential input capability, and a fast 200 ns response time, housed in an 8-pin PDIP package. Verified distributor data identifies a maximum input offset voltage of 2 mV, while another supplier lists 1 mV at ±15 V; engineers should therefore verify the exact test conditions in the manufacturer datasheet before setting precision thresholds. A voltage comparator is an analog interface IC that compares two input voltages and produces a logic-level result indicating which input is higher. It belongs to the comparator hierarchy within interface and signal-conditioning semiconductors. Unlike a general-purpose operational amplifier used primarily for linear amplification, a comparator is optimized for fast saturation and switching, making it useful for threshold detection, sensor conditioning, pulse shaping, and control systems. The LT311AN8 combines a single comparator with an 8-pin through-hole package. The verified supply specifications include 5V to 30V operation and ±2.5 V to ±15 V dual-supply operation. A 200 ns response time supports applications requiring rapid transitions, while the stated bipolar input arrangement supports operation around ground and with bipolar supplies. Exact input common-mode limits, output-swing limits, hysteresis behavior, and latch configuration were not provided in the verified data and require datasheet confirmation. Typical circuit roles include monitoring a sensor output against a reference, detecting an overvoltage condition, converting a slowly changing analog level into a digital event, and generating a pulse when a threshold is crossed. Because a comparator output can change rapidly near its switching threshold, input noise, propagation delay, output-capacitance, and layout parasitics can affect system behavior. A stable reference and short feedback or hysteresis path may be needed when the input signal has appreciable noise or slow slew rate. The principal design consideration is to verify supply polarity, input range, output compatibility, and logic thresholds against the actual operating rail. Do not assume that the 30 V maximum supply rating permits inputs or outputs outside the device's specified common-mode and absolute-maximum limits. Confirm that downstream devices accept the electrical output levels and that the comparator's response time is adequate for the required timing margin. This page consolidates the verified distributor identity, package, supply, offset, response-time, and commercial-search data for LT311AN8. It also distinguishes verified facts from missing technical fields and avoids presenting unverified drop-in substitutes as guaranteed replacements, helping engineers evaluate the part with appropriate sourcing and validation caution.

見積もり お問い合わせ
LT318AH - 15MHz High-Speed Operational Amplifier | Analog Devices
LT318AH

LT318AH - 15MHz High-Speed Operational Amplifier | Analog Devices

The Analog Devices LT318AH is a standard general-purpose high-speed operational amplifier with one circuit, a nominal unity-gain bandwidth of 15 MHz, and an 8-lead round TO-5 through-hole package. The verified distributor information identifies the device as a high-speed operational amplifier, while the available product data also lists a 70 V/µs slew rate and approximately 5 mA supply current. Its military-grade designation and hermetic-style package make it relevant to precision analog, signal-conditioning, instrumentation, and test systems where bandwidth and transient response matter. An operational amplifier is an analog integrated circuit that uses high-gain feedback to amplify the difference between two input voltages. In the broader electronics hierarchy, the LT318AH is an operational amplifier, analog IC, and semiconductor. Its high bandwidth permits wider signal bandwidth than slower general-purpose amplifiers, while its slew rate determines how quickly the output can move through voltage changes. These characteristics make it useful in active filters, buffers, low-level signal chains, feedback control, and measurement circuits. The verified data identifies the LT318AH as a single-circuit amplifier with a 15 MHz nominal unity-gain bandwidth and 70 V/µs slew rate. The available distributor listing also reports approximately 0.5 µA maximum average input bias current in one marketplace result, while another product listing reports a 5 mA supply current. These figures should be checked against the manufacturer datasheet for the exact test conditions, supply voltage, temperature grade, and load conditions before final design sign-off. The device is packaged as an 8-terminal round TO-5/MDTALCAN through-hole package. Its leaded construction is mechanically distinct from modern surface-mount op amps, so PCB replacement must account for the original footprint, lead spacing, thermal requirements, and pin orientation. The verified sources disagree on some commercial and historical details, including temperature-grade descriptions and lifecycle status, so those fields remain qualification-dependent rather than inferred. Typical uses include high-speed instrumentation, precision signal buffering, active analog filtering, test-equipment input stages, and feedback loops requiring faster transient response than a conventional low-frequency precision amplifier. For new designs, verify the exact LT318AH datasheet, military qualification requirements, supply limits, input/output ranges, noise, bias current, stability configuration, and availability before committing the layout. The key design consideration is to verify the complete pinout and electrical limits in the manufacturer datasheet before layout or replacement. Decouple the supply pins locally, keep feedback traces short, and verify stability with the intended source and load. Because this is a through-hole TO-5 device, production cost, availability, and thermal performance may differ substantially from newer surface-mount alternatives. This page consolidates verified manufacturer and distributor information with explicit data gaps, practical application guidance, and drop-in replacement screening. It does not invent missing electrical values, lifecycle claims, qualification details, or cross-reference parts that were not established by the supplied evidence.

見積もり お問い合わせ
LT318AJ8 - High-Speed Operational Amplifier | Analog Devices
LT318AJ8

LT318AJ8 - High-Speed Operational Amplifier | Analog Devices

The Analog Devices LT318AJ8 is a single-circuit, high-speed operational amplifier in an 8-pin CERDIP package. The verified product data identifies it as a standard general-purpose instrumentation amplifier building block with eight through-hole terminals and a commercial temperature grade. Its high-speed architecture is intended for precision signal paths where response speed and signal integrity matter more than micropower operation. An operational amplifier is an active analog device that uses high open-loop gain to amplify the difference between its inverting and non-inverting inputs. In the broader electronics hierarchy, it belongs to the operational-amplifier family, then to analog signal-conditioning ICs and semiconductors. Negative feedback commonly shapes closed-loop gain, while the amplifier supplies the output current needed to drive the external load. The LT318A family is specifically described by Analog Devices as a high-speed operational amplifier. That classification makes it relevant to instrumentation, measurement, buffering, and precision feedback systems. The available verified sources do not publish numerical gain-bandwidth, slew-rate, input-offset, supply-voltage, noise, or current figures, so those values must be taken directly from the manufacturer data sheet before sizing compensation, checking stability, or calculating noise performance. The J8 ordering code corresponds to the 8-pin CERDIP package shown by DigiKey and other distributors. A through-hole ceramic dual-inline package supports conventional PCB insertion and is distinct from surface-mount SOIC variants. The suffix should not be treated as an electrical grade or performance option by itself; confirm the complete family data and ordering information in the Analog Devices LT318A documentation. Typical uses include precision instrumentation signal conditioning, low-level analog amplification, active filtering, data-acquisition front ends, and feedback networks in measurement systems. These applications benefit from the device's stated high-speed characterization, but stability and bandwidth must be confirmed against the actual closed-loop circuit, source impedance, load, supply rails, and compensation network. The principal design consideration is that package compatibility alone does not guarantee replacement compatibility. Verify offset voltage, input bias current, slew rate, gain-bandwidth product, output swing, supply range, noise, and stability for any substitute. Decoupling, grounding, feedback-loop layout, and output-load conditions can affect performance as much as the nominal amplifier specifications. This page combines verified manufacturer and distributor information with package, sourcing, comparison, and design guidance. It distinguishes documented facts from missing numerical parameters and does not infer an electrical match where the supplied sources do not provide one.

見積もり お問い合わせ
LT318AN8#PBF - 15MHz 70V/us Op Amp | Analog Devices
LT318AN8#PBF

LT318AN8#PBF - 15MHz 70V/us Op Amp | Analog Devices

The Analog Devices LT318AN8#PBF is a single, general-purpose, high-speed operational amplifier with 15 MHz gain-bandwidth product, 70 V/us slew rate, and one circuit in an 8-pin PDIP package. The through-hole DIP format supports conventional PCB insertion and prototyping, while the leaded package is suited to instrumentation, signal-conditioning, and test systems. According to the manufacturer product page, the LT318A family is in production and begins at $3.46 per unit. A high-speed operational amplifier is a voltage-feedback amplifier designed to amplify small signal variations while maintaining useful bandwidth and slew performance. In the electronics hierarchy, an operational amplifier belongs to the amplifier-IC family and the broader semiconductor category. The LT318A's combination of bandwidth, slew rate, and general-purpose classification makes it relevant where signal response must be faster than that of conventional precision or low-noise amplifiers. The verified data identifies the LT318A as a 15 MHz high-speed amplifier with a 70 V/us slew rate. These two specifications describe different dynamic limits: gain-bandwidth product controls small-signal response, while slew rate controls how rapidly the output can move under large-signal conditions. The 8-DIP package measures 0.300 inches, or 7.62 mm, according to the distributor specification listing, and the product is supplied in a tube. The LT318AN8#PBF is categorized by DigiKey as a standard, general-purpose amplifier with one circuit. Its 8-terminal PDIP construction and through-hole form factor distinguish it from surface-mount operational amplifiers, making it useful where component insertion, socket use, or manual replacement is preferred. Because high-speed amplifiers can oscillate or produce unstable outputs when layout and compensation conditions are poor, feedback routing, grounding, bypassing, and load capacitance require careful attention. Typical uses include low-frequency instrumentation signal paths, laboratory test equipment, communications-related signal conditioning, analog control blocks, and educational or prototyping circuits. The verified data does not provide input-offset voltage, input-bias current, noise density, common-mode range, supply range, output swing, or stability-versus-capacitance values, so those specifications should be confirmed in the LT318A manufacturer datasheet before final design release. The principal design consideration is to preserve high-speed behavior without introducing excessive instability. Keep feedback components close to the amplifier, use a compact ground-return path, bypass supply pins at the circuit, and avoid long unprotected traces. If the load is capacitive or the feedback network is electrically long, compare the simulated result against the manufacturer's recommended compensation and stability guidance. This page combines the verified manufacturer and distributor metadata with a practical explanation of package, speed, sourcing, and design-selection questions. It also distinguishes confirmed LT318A attributes from parameters that still require datasheet verification, avoiding unsupported claims while helping engineers plan instrumentation and high-speed analog prototypes.

見積もり お問い合わせ
LT319AH - Dual Open-Collector Comparator | Analog Devices
LT319AH

LT319AH - Dual Open-Collector Comparator | Analog Devices

The Analog Devices LT319AH is a production dual comparator with two independent high-gain comparison channels, open-collector outputs, bipolar construction, and a 10-pin round TO-5 through-hole package. The verified distributor data identifies a commercial-grade part with an operating temperature range of 0°C to 70°C, bipolar technology, and dual supplies spanning ±2.5 V minimum to ±15 V maximum. Its 80 ns response figure and open-collector output make it useful for line-driver, threshold, and interface circuits. A comparator is an analog integrated circuit that compares two input voltages and produces a digital logic state indicating whether the non-inverting input is above or below the inverting input. The LT319AH belongs to the dual-comparator hierarchy, combining two similar channels in one package. Its open-collector outputs require an external pull-up resistor when the output must rise to a defined logic high. Verified product information describes the LT319AH as an improved relative to the LM119 family, with lower input offset voltage and offset current, higher voltage gain, guaranteed common-mode rejection, and input protection diodes. The identified response time is 80 ns, while one distributor result reports 150 nA input bias current. These features support applications that require fast decisions, predictable offset behavior, and protection at the inputs. The LT319AH is produced under the Analog Devices product family and has a listed starting price of $3.23 on the official product page. Commercial-grade operation from 0°C to 70°C supports cost-sensitive industrial and instrumentation designs when that temperature range is acceptable. Its through-hole TO-5 package is mechanically straightforward for legacy PCBs, test fixtures, and hand-assembled prototypes. Typical circuit roles include dual-threshold detection, pulse-width or timing comparison, low-level digital interfacing, and two-channel sensing. Because the outputs are open collector, designers should verify pull-up voltage, pull-up resistance, sink-current capability, input common-mode limits, and supply polarity before implementation. The separate ground arrangement should also follow the manufacturer’s connection guidance. For new layouts, a surface-mount alternative may be mechanically easier to automate, but changing packages requires a PCB redesign. For repair and legacy production, keeping the original TO-5 footprint and verifying the 10-pin connection order is more important than selecting a merely similar dual comparator. This page consolidates verified manufacturer information, distributor availability references, pricing context, package details, and practical procurement guidance for engineers evaluating the LT319AH. It does not infer a drop-in replacement where the provided evidence does not establish one.

見積もり お問い合わせ
LT319AN - Dual 80ns Comparator, 14-PDIP | Analog Devices
LT319AN

LT319AN - Dual 80ns Comparator, 14-PDIP | Analog Devices

The Analog Devices LT319AN is a dual, general-purpose comparator with a guaranteed maximum 0.5 mV input offset voltage, 80 ns response time, 25 mA output drive capability, and operation from a single 5 V supply. It is packaged in a 14-pin PDIP. The LT319AN is the leaded, non-automotive-temperature designation associated with the LT319A dual-comparator family. A comparator is an integrated circuit that compares two input voltages and produces a logic-level output indicating which input is higher. As a dual comparator, the LT319AN contains two independent comparison channels in one package. This dual-channel structure places the device in the comparator hierarchy: comparator > analog comparator > linear integrated circuit > semiconductor. It is useful when a system needs fast threshold detection, signal conditioning, or differential logic conversion. The LT319A family is described by Analog Devices as an improved version of the LM119 dual comparator. Its key advantages include lower input offset voltage and offset current, higher voltage gain, guaranteed common-mode rejection, and input protection diodes. The maximum 0.5 mV offset specification reduces ambiguity near the switching threshold, while the 80 ns response time supports high-speed decision-making. The 25 mA output drive capability allows the outputs to interface with suitable TTL-compatible circuitry. Operation from a single 5 V supply simplifies the power architecture in TTL and mixed-signal systems. The 14-pin PDIP package also supports conventional through-hole assembly and prototyping. Because output behavior and input common-mode limits depend on the supply configuration, designers should consult the manufacturer datasheet before using the device outside its stated operating conditions. The separate ground arrangement discussed for the LT319A family can also assist system-ground isolation where applicable. Typical uses include high-speed threshold detection, pulse-width and timing measurements, zero-cross detection, signal conditioning, and two-channel sensing. One comparator channel can compare a sensor signal with a reference while the other performs an independent threshold or differential decision. The fast 80 ns response helps minimize propagation delay in timing-sensitive systems, and the 0.5 mV maximum input offset improves threshold repeatability. Layout should keep input and output paths short, provide a stable return path, and avoid routing sensitive input traces beside high-current switching nodes. Input protection diodes require attention when signals can exceed the supply rails. Designers should also account for output rise and fall time, supply bypassing, and input common-mode range when interpreting the 80 ns response specification. This page combines the verified manufacturer and distributor information with practical application guidance, sourcing details, comparison data, and design notes. It distinguishes explicitly verified LT319AN characteristics from parameters that still require confirmation from the official LT319A datasheet.

見積もり お問い合わせ
LT319AN#PBF - 80ns Dual Comparator, 14-PDIP | Analog Devices
LT319AN#PBF

LT319AN#PBF - 80ns Dual Comparator, 14-PDIP | Analog Devices

The Analog Devices LT319AN#PBF is a dual general-purpose comparator with an 80 ns response time, open-collector outputs, and a 14-pin PDIP package. It operates from a single 5 V supply or from supply voltages spanning ±15 V. The device contains two independent comparison channels and is specified with a maximum input offset voltage of 0.5 mV, 25 mA output drive capability, and input protection diodes. A comparator is a high-gain analog signal-conditioning IC that evaluates two input voltages and produces a digital logic result indicating which input is higher. The LT319A belongs to the comparator hierarchy, which supports general-purpose analog and mixed-signal systems: comparator -> analog signal IC -> integrated circuit -> semiconductor. Its open-collector output requires an external pull-up resistor and can interface with systems using open-collector, open-emitter, or TTL-compatible signaling. Key features include two comparators per package, an 80 ns response time, a guaranteed maximum 0.5 mV input offset voltage, and 25 mA output drive capability. The single 5 V operating capability is useful for low-voltage logic systems, while the ±15 V supply capability supports higher-voltage analog and industrial control circuits. Input protection diodes help limit input stress, although external protection and supply-decoupling checks remain necessary in the final design. The LT319A architecture is intended for threshold detection, level translation, pulse generation, and high-speed switching decisions. Because the outputs are open collector, the output high level depends on the pull-up network and system voltage rather than an internal active pull-up. This makes the device adaptable to different logic families, but it also requires correct resistor selection and confirmation that the driven node meets the timing and current requirements of the receiving circuit. Typical applications include industrial control and automation, sensor threshold detection, pulse-width and timing circuits, level conversion, waveform conditioning, and embedded control systems. The 14-pin PDIP package is mechanically straightforward for through-hole assembly, prototyping, and repair. Its dual-channel configuration also reduces package count when two independent decisions are required in one circuit. When designing around the LT319AN#PBF, verify supply polarity, common-mode input limits, output pull-up values, and the maximum transition rate required by the downstream logic. Place bypass capacitors close to the supply pins and keep comparator input traces short to reduce noise pickup. The open-collector outputs can pull a logic node low but cannot source current, so a suitable pull-up resistor is mandatory. This page combines verified manufacturer and distributor data with practical comparator design guidance, application fit, package information, and drop-in replacement considerations for engineers evaluating the LT319AN#PBF.

見積もり お問い合わせ
LT3669EUFD#PBF - IO-Link Transceiver with Buck/LDO | Analog Devices
LT3669EUFD#PBF

LT3669EUFD#PBF - IO-Link Transceiver with Buck/LDO | Analog Devices

The Analog Devices LT3669EUFD#PBF is an industrial IO-Link transceiver with an integrated step-down switching regulator and low-dropout linear regulator in a 28-QFN package. It combines wake-up detect functionality, a programmable power-on reset timer, and externally adjustable transmitter current limit and slew rate. The device is identified as a single transmitter/receiver IO-Link interface solution for industrial sensor and actuator systems. An IO-Link transceiver is a specialized interface IC that connects sensors, actuators, and industrial equipment using power and communication lines. The LT3669 integrates that interface function with local power conversion, allowing a system designer to provide both the IO-Link communication path and regulated auxiliary power from one device. Its architecture belongs to the transceiver, interface IC, power-management IC, and embedded industrial-control hierarchy. The principal verified features include a 28-pin QFN surface-mount package, integrated step-down regulator and LDO, wake-up detect, programmable power-on reset timing, and adjustable transmitter current limit and slew rate. The manufacturer describes the LT3669 family as recommended for new designs. These features make it useful in industrial IO-Link master or sensor interfaces where space, local power, fault handling, and deterministic startup behavior matter. The device can be used in industrial automation equipment, factory sensor nodes, actuator interfaces, process-control systems, and IO-Link-compatible sensor modules. The integrated power regulators reduce the number of separate support components, while wake-up detection can help a connected system recognize a remote device state. The programmable power-on reset timer provides additional control during system startup and recovery. When designing around the LT3669EUFD#PBF, engineers should verify the exact electrical limits, pin functions, regulator settings, and external component values against the official LT3669/LT3669-2 datasheet. The QFN package also requires careful PCB layout and thermal management. The integrated switching regulator can introduce layout-dependent EMI and high-current paths, so input decoupling, switching-loop minimization, and exposed-pad thermal design should be reviewed before production. This product page combines the verified Analog Devices product information, distributor listings, and practical engineering guidance. It is intended to help engineers identify the correct IO-Link transceiver, compare package and lifecycle information, locate the datasheet, and plan a robust industrial interface implementation. The target MPN includes the E suffix and PBF lead-free ordering designation; variant and package details should be confirmed against the manufacturer documentation before substituting or upgrading. LT3669EUFD#PBF is best suited to compact industrial IO-Link systems where communication, auxiliary power, wake-up detection, and programmable startup behavior are integrated in a single 28-QFN device. Use the manufacturer datasheet as the authority for final electrical, thermal, timing, and application values.

見積もり お問い合わせ
LT3669EUFD#TRPBF - IO-Link Transceiver | Analog Devices
LT3669EUFD#TRPBF

LT3669EUFD#TRPBF - IO-Link Transceiver | Analog Devices

The Analog Devices LT3669EUFD#TRPBF is an industrial IO-Link transceiver with an integrated step-down switching regulator and low-dropout regulator, housed in a 28-QFN surface-mount package. The verified product listing identifies a 4 mm by 5 mm package and tape-and-reel ordering code TRPBF. Its integrated power architecture supports IO-Link sensor or actuator interfaces while reducing the number of external power-conversion stages required around the field device. An IO-Link transceiver is an industrial interface IC that connects a controller to sensors or actuators using IO-Link communication. In the broader hierarchy, it belongs to interface ICs and industrial fieldbus connectivity. The LT3669 family combines physical-layer signaling, wake-up detection, programmable power-on reset timing, and local power regulation so a compact sensor or actuator can be powered and communicated with in one assembly. According to the Analog Devices product page, LT3669 and LT3669-2 are recommended for new designs. The manufacturer datasheet also identifies wake-up detect and a programmable power-on reset timer. The transceiver's transmitter current limit and slew rate are externally adjustable, allowing the interface behavior to be matched to the connected industrial load and cable environment. The verified data does not provide numerical values for those adjustments. The integrated step-down regulator supplies a lower-voltage rail efficiently, while the LDO supports a cleaner local supply. Combining both functions with the IO-Link transceiver can simplify PCB area in industrial sensors, proximity devices, and actuator modules. The trade-off is a more specialized IC whose external component values, current limits, timing, and thermal performance must be selected together rather than as separate power-stage designs. The LT3669 family is suitable for factory automation, industrial sensing, actuator control, and fieldbus-connected modules where IO-Link power and communication share one interface device. The 28-QFN package requires careful PCB layout and adequate thermal design, particularly when the internal switching regulator operates at higher load. The manufacturer product page lists LT3669 and LT3669-2 as recommended for new designs, while the exact LT3669EUFD#TRPBF lifecycle status should be confirmed against current authorized-channel inventory. This page combines verified distributor listings, manufacturer positioning, package information, and practical design guidance for engineers evaluating the LT3669EUFD#TRPBF. Numeric electrical limits, pricing tiers, and detailed pin functions not present in the supplied source data are intentionally marked as data needed rather than inferred.

見積もり お問い合わせ
LT3669EUFD-2#PBF - IO-Link Transceiver with Integrated Buck Regulator and LDO | Analog Devices
LT3669EUFD-2#PBF

LT3669EUFD-2#PBF - IO-Link Transceiver with Integrated Buck Regulator and LDO | Analog Devices

The Analog Devices LT3669EUFD-2#PBF is an IO-Link transceiver with an integrated step-down switching regulator and low-dropout linear regulator, designed for industrial interface applications and housed in a 28-pin QFN package. The LT3669-2 version supports an external catch diode and up to 300 mA switching-regulator load current according to the Analog Devices product page. The device combines one IO-Link transmitter and one receiver with wake-up detection and a programmable power-on reset timer, reducing the need for separate interface and power-management circuitry. An IO-Link transceiver is a specialized industrial interface IC that connects compatible sensors and actuators to a point-to-point communication link. The LT3669 combines this interface function with power conversion, placing the component in the broader hierarchy of industrial interface IC, transceiver, power-management IC, and semiconductor. Its integrated regulator can supply the connected IO-Link device while the transceiver handles wake-up, communication, and fault-related interface behavior. Key features identified in the verified Analog Devices material include one transmitter and one receiver, a 7.5 V to 40 V supply range, and a -40°C to +125°C operating-temperature range for the LT3669 comparison result. The LT3669-2 uses an external catch diode rather than the integrated catch diode used in the LT3669, making the external-diode distinction important when comparing versions. The manufacturer describes the LT3669 family as recommended for new designs. The switching-regulator and LDO architecture can simplify industrial sensor or actuator boards by reducing external power-conversion component count. The programmable power-on reset timer supports controlled startup sequencing, while wake-up detection helps the system respond to connected-device activity. Current limit and transmitter slew rate are externally adjustable according to the manufacturer datasheet, allowing board-level optimization for the intended interface load and cable environment. Typical applications include IO-Link sensors, proximity and position sensors, industrial actuators, factory automation equipment, and distributed industrial control systems. The wide 7.5 V to 40 V supply range is relevant for 24 V industrial environments, while the integrated regulator architecture is useful where board space and component count matter. The exact external diode, capacitor, resistor, and layout requirements must follow the Analog Devices datasheet. When designing a board around the LT3669EUFD-2#PBF, confirm the external catch-diode selection, regulator compensation, output capacitance, and exposed-pad thermal implementation against the manufacturer guidance. Keep sensitive communication and power-return paths short, and provide adequate copper area for the 28-QFN package. Verify the selected sensor or actuator’s IO-Link current, wake-up behavior, and electrical timing before finalizing the power budget. This page consolidates the verified manufacturer and distributor information, distinguishes the LT3669 and LT3669-2 external-diode distinction, and provides design-oriented guidance. Current pricing and availability remain distributor-dependent and should be checked for the exact suffix and order quantity.

見積もり お問い合わせ
LT3669EUFD-2#TRPBF - IO-Link Transceiver with Dual Regulators
LT3669EUFD-2#TRPBF

LT3669EUFD-2#TRPBF - IO-Link Transceiver with Dual Regulators

The Analog Devices LT3669EUFD-2#TRPBF is a 1/1 IO-Link industrial transceiver with an integrated step-down switching regulator and low-dropout regulator, housed in a 28-lead 4 mm by 5 mm QFN package. The verified product data identifies the device for surface mounting and reel-and-tape handling, with an operating temperature range of -40°C to 125°C. Its integrated power architecture supports the sensor-side requirements of IO-Link industrial connections while reducing the number of external supply components. An IO-Link transceiver is an interface IC that connects a microcontroller or PLC-side controller to an industrial point-to-point sensor or actuator link. IO-Link adds standardized digital communication and wake-up or power-control capabilities beyond a conventional simple sensor output. The LT3669 family combines that physical-layer interface with power-conversion functions, placing the transceiver, switching regulator, and LDO in one package. Verified features include 1/1 transceiver operation, IO-Link functionality, integrated step-down regulation, integrated LDO operation, wake-up detection, and a programmable power-on reset timer for the LT3669 family. The Analog Devices LT3669-2 is listed for up to 300 mA load current and requires an external catch diode, whereas the LT3669 variant integrates the catch diode and is listed for up to 100 mA load current. The 28-QFN (4x5) exposed-pad package is designed for surface-mount assembly and can provide a compact solution where both signal interface and local power conversion are required. The exposed pad also supports thermal conduction into the PCB, although actual thermal performance depends on copper area, board construction, ambient temperature, and load. Use the manufacturer datasheet for pin functions, recommended external components, electrical limits, timing, and layout details before finalizing a design. Typical applications include IO-Link sensors, industrial proximity and level sensors, factory automation equipment, PLC-connected actuators, and other 24 V industrial fieldbus nodes. The LT3669EUFD-2#TRPBF is most appropriate when a compact 28-QFN footprint, integrated regulators, and the LT3669-2 external-catch-diode architecture fit the system specification. Design attention should focus on correct pin mapping, regulator stability, catch-diode selection, exposed-pad thermal management, and separation between sensitive communication traces and switching-power paths. The verified distributor record identifies the part as a 28-QFN (4x5) IO-Link transceiver, but detailed application limits and package dimensions must be confirmed from the official Analog Devices documentation. This product data combines the verified manufacturer and distributor identity, package information, family-level functional description, commercial source links, and practical design guidance into an engineering-oriented reference for IO-Link transceiver and power-management design.

見積もり お問い合わせ
LT3669HUFD#PBF - 40V IO-Link Interface | Analog Devices
LT3669HUFD#PBF

LT3669HUFD#PBF - 40V IO-Link Interface | Analog Devices

The Analog Devices LT3669HUFD#PBF is an industrial IO-Link transceiver with integrated 16 V step-down and 150 mA LDO functions, operating from a 7.5 V to 40 V supply in a 28-pin QFN package. It combines one IO-Link physical-layer channel, protected line-driver outputs, wake-up detection, and a programmable power-on reset timer. The verified product information identifies ±60 V cable-interface protection and rugged line drivers for industrial sensor and actuator cabling. An IO-Link transceiver is an interface IC that connects a microcontroller or sensor hub to an industrial point-to-point cable while combining digital communication and power delivery. In the hierarchy, the LT3669 is an IO-Link interface transceiver with integrated DC-DC converter and LDO. That integration reduces the number of separate supply blocks needed at a remote industrial sensor, actuator, or factory I/O node while retaining communication and power management in one device. The main feature set includes compatibility with COM1, COM2, and COM3, operation from 40 V, a 16 V step-down switching-regulator output, an integrated 150 mA low-dropout regulator, and ±60 V cable-interface protection. Wake-up detection supports systems that must detect activity on a connected cable. A programmable power-on reset timer provides controlled startup behavior for downstream circuitry, which is useful when load power must become valid only after timing requirements are met. Technically, the part combines three functional blocks in one surface-mount device: an IO-Link physical layer, a step-down switching regulator, and an LDO. The integrated supply architecture is especially useful in industrial systems where a higher-voltage bus powers a lower-voltage sensor. Its stated −40 °C to 150 °C operating range for the H-grade comparison result broadens environmental suitability, but designers should confirm all limits and derating requirements against the manufacturer datasheet before release. Typical applications include IO-Link sensor masters, proximity and photoelectric sensors, industrial actuator interfaces, factory automation equipment, remote I/O modules, and motor or process-control systems. The single-transceiver configuration is appropriate when one cable segment must carry IO-Link data while receiving local regulated power. Design the printed-circuit board with short, protected cable-side traces and place input, switching-regulator, and LDO capacitors according to the manufacturer layout guidance. Validate startup sequencing, exposed-pad thermal performance, surge operation, and fault behavior across the complete industrial supply and cable transient range. This page consolidates verified manufacturer and distributor information, documented alternatives, interface functions, and design cautions into a procurement-oriented engineering reference without inferring unverified electrical or pin-level details.

見積もり お問い合わせ
LT3669HUFD#TRPBF - Integrated IO-Link Power | Analog Devices
LT3669HUFD#TRPBF

LT3669HUFD#TRPBF - Integrated IO-Link Power | Analog Devices

The Analog Devices LT3669HUFD#TRPBF is a single-channel industrial IO-Link transceiver with an integrated step-down switching regulator and low-dropout linear regulator, housed in a 28-pin QFN package with an exposed pad. The verified product data identifies a 4 mm by 5 mm package, while detailed operating, current, voltage, timing, and pin-function values were not included in the supplied records and must be confirmed in the manufacturer datasheet. An IO-Link transceiver is a specialized industrial interface that combines a physical-layer data channel with sensor or actuator support circuitry. This device additionally manages local power requirements, making it useful when an IO-Link node needs both communications and regulated power without using separate power-conversion stages. In system terms, it belongs to the interface-IC hierarchy while also incorporating DC-DC converter and linear-regulator functions. The LT3669 family is described by Analog Devices as an industrial transceiver with an integrated step-down regulator, LDO, wake-up detection, and a programmable power-on reset timer. The transmitter current limit and slew rate are externally adjustable, allowing the designer to tune output behavior for the connected IO-Link master, cable, load, and application timing. These functional details distinguish it from a basic digital line-driver or receiver. The LT3669 family is available in LT3669 and LT3669-2 versions, with LT3669-2 identified by the manufacturer as recommended for new designs. The supplied distributor record confirms that the target is supplied in a 28-QFN 4 mm by 5 mm surface-mount package. The exposed thermal pad should be connected according to the datasheet land pattern and thermal recommendations rather than treated as an unused pin. Typical uses include industrial IO-Link sensor interfaces, factory automation nodes, proximity and light-sensor links, actuator connections, and compact industrial control modules. The integrated regulators can simplify power partitioning, while the transceiver supports communication between a master and an IO-Link-compatible peripheral. Actual operating limits and timing must be checked against the complete datasheet before design release. For robust implementation, preserve the recommended input and output capacitors, follow the exposed-pad land pattern, validate adjustable current-limit and slew-rate settings, and check reset or wake-up timing against the system power sequence. This page combines verified manufacturer and distributor information with explicit data-gap markers rather than estimating electrical performance. This page consolidates verified sourcing, package information, lifecycle guidance, application context, and replacement guidance that are not consolidated in a raw distributor listing. LT3669 family options are distinguished carefully, while unverified competitor equivalents are excluded.

見積もり お問い合わせ
LT3669HUFD-2#PBF - Integrated IO-Link Interface | Analog Devices
LT3669HUFD-2#PBF

LT3669HUFD-2#PBF - Integrated IO-Link Interface | Analog Devices

The Analog Devices LT3669HUFD-2#PBF is an industrial IO-Link transceiver with an integrated step-down switching regulator and low-dropout linear regulator, supplied in a 28-lead 4 mm by 5 mm plastic QFN package. The verified product information identifies its interface supply range as 7.5 V to 40 V. The LT3669-2 version supports a switching-regulator load current up to 300 mA and requires an external catch diode, unlike the base LT3669 version, which integrates the catch diode and supports up to 100 mA. An IO-Link transceiver is a specialized interface IC that connects an industrial sensor or actuator to a point-to-point IO-Link master. It combines the physical communication interface with local power-management functions, reducing the number of separate components required at the sensor end of an industrial link. This device also includes wake-up detection and a programmable power-on reset timer for managed sensor power behavior. Key features include the integrated step-down regulator, integrated LDO, IO-Link communication, wake-up detect, programmable power-on reset, and operation from a 7.5 V to 40 V interface supply. The LT3669-2 configuration is intended for designs requiring the higher 300 mA switching-regulator load capability. Its 28-QFN package is compact but requires careful layout and exposed-pad thermal management. According to the manufacturer product page, the LT3669 and LT3669-2 are recommended for new designs. The manufacturer also identifies the LT3669-2 as requiring an external catch diode, making circuit implementation distinct from the original LT3669. The available verified source set does not provide a complete electrical limit table, pin-by-pin mapping, compliance declarations, or pricing tiers beyond the manufacturer's listed starting price. Typical uses include proximity sensors, photoelectric sensors, industrial actuators, decentralized IO-Link sensor nodes, factory automation equipment, and other 24 V industrial sensing systems. The local regulators can power sensor electronics while the transceiver handles wake-up communication with the IO-Link master. When designing the circuit, follow the manufacturer datasheet for the external catch diode, inductor, capacitors, exposed-pad layout, and decoupling values. Treat the 4 mm by 5 mm QFN thermal pad as a heat-spreading structure and verify copper area, via count, and temperature rise against the actual regulator dissipation. This page combines verified manufacturer and distributor information with replacement evidence, interface guidance, and design cautions that are not consolidated on a basic distributor listing. It separates confirmed LT3669-2 differences from specifications that still require the complete datasheet or design-specific validation.

見積もり お問い合わせ