LT3669HUFD#PBF - 40V IO-Link Interface | Analog Devices
部品番号: LT3669HUFD#PBF ✓ 生産中| 数量 | 単価 | 小計 |
|---|---|---|
| 1 | $3.8294 | $3.83 |
| 10 | $3.8294 | $38.29 |
| 100 | $3.8294 | $382.94 |
| 500 | $3.8294 | $1,914.70 |
| 1,000 | $3.8294 | $3,829.40 |
LT3669HUFD#PBF 概要
An IO-Link transceiver is an interface IC that connects a microcontroller or sensor hub to an industrial point-to-point cable while combining digital communication and power delivery. In the hierarchy, the LT3669 is an IO-Link interface transceiver with integrated DC-DC converter and LDO. That integration reduces the number of separate supply blocks needed at a remote industrial sensor, actuator, or factory I/O node while retaining communication and power management in one device.
The main feature set includes compatibility with COM1, COM2, and COM3, operation from 40 V, a 16 V step-down switching-regulator output, an integrated 150 mA low-dropout regulator, and ±60 V cable-interface protection. Wake-up detection supports systems that must detect activity on a connected cable. A programmable power-on reset timer provides controlled startup behavior for downstream circuitry, which is useful when load power must become valid only after timing requirements are met.
Technically, the part combines three functional blocks in one surface-mount device: an IO-Link physical layer, a step-down switching regulator, and an LDO. The integrated supply architecture is especially useful in industrial systems where a higher-voltage bus powers a lower-voltage sensor. Its stated −40 °C to 150 °C operating range for the H-grade comparison result broadens environmental suitability, but designers should confirm all limits and derating requirements against the manufacturer datasheet before release.
Typical applications include IO-Link sensor masters, proximity and photoelectric sensors, industrial actuator interfaces, factory automation equipment, remote I/O modules, and motor or process-control systems. The single-transceiver configuration is appropriate when one cable segment must carry IO-Link data while receiving local regulated power.
Design the printed-circuit board with short, protected cable-side traces and place input, switching-regulator, and LDO capacitors according to the manufacturer layout guidance. Validate startup sequencing, exposed-pad thermal performance, surge operation, and fault behavior across the complete industrial supply and cable transient range.
This page consolidates verified manufacturer and distributor information, documented alternatives, interface functions, and design cautions into a procurement-oriented engineering reference without inferring unverified electrical or pin-level details.
ドロップイン代替品: LT3669HUFD#PBF — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
このシリーズのバリエーション
同一シリーズでドロップイン互換のモデル: LT3669HUFD#PBF （同一形状・フットプリント） — 相違点: Package, Product Type, Wake-Up Detect, Operating Temperature Range, Product Status.
クイック比較ツール — 並列比較する代替部品を選択:
LT3669EUFD#PBF
✅ ドロップイン✓ 在庫あり
$9.2 / 個
データシートを見る →LT3669EUFD-2#PBF
✅ ドロップイン✓ 在庫あり
$5.38 / 個
データシートを見る →LT3669HUFD-2#PBF
✅ ドロップイン✓ 在庫あり
$5.38 / 個
データシートを見る →LT3669HUFD#PBF 仕様
| Product Type | IO-Link transceiver with integrated step-down regulator and LDO |
| Transmitter/Receiver Count | 1 transmitter and 1 receiver |
| IO-Link Modes | COM1, COM2, and COM3 compatible |
| 電源電圧 | 7.5 V to 40 V |
| Cable Interface Protection | ±60 V |
| Integrated Step-Down Output | 16 V |
| Integrated LDO Output Current | 150 mA |
| Wake-Up Detect | Integrated |
| Power-On Reset | Programmable timer |
| 動作温度 | -40 °C to 150 °C |
| パッケージ | 28-pin QFN, 4 mm × 5 mm, exposed pad |
| 実装タイプ | Surface mount |
| Line Drivers | Rugged line drivers |
| Tube Packaging | Tube |
| RoHS | Details available; exact status not stated in verified snippets |
LT3669HUFD#PBF 28-pin qfn, 4 mm × 5 mm, exposed pad ピン配置ガイド
LT3669HUFD#PBF (28-pin qfn, 4 mm × 5 mm, exposed pad パッケージ) のピン配置。 ピン番号、機能、接続図はメーカーのデータシートで定義されています。正確なフットプリントとはんだ付けのガイドラインについては、データシートを参照してください。
詳細なピン配置データはありません: LT3669HUFD#PBF.
詳細は データシート をご参照ください。
主な用途
LT3669HUFD#PBF の用途: 6 件s: IO-Link Sensor Master Interface, Industrial Proximity Sensor Interface, Factory Actuator Interface, Remote I/O Module, Industrial Motor-Control Interface, Process-Control Sensor Node.
IO-Link Sensor Master Interface
The LT3669HUFD#PBF fits a point-to-point IO-Link master because it combines COM1, COM2, and COM3 compatibility with one transmitter and one receiver. Its 7.5 V to 40 V operating range supports industrial bus-derived systems, while the integrated 16 V step-down regulator and 150 mA LDO can organize local sensor power. The same QFN device also provides wake-up detection, helping the master recognize activity on a connected sensor cable. Cable protection must still be evaluated against the actual wiring length and surge environment.
おすすめ
Industrial Proximity Sensor Interface
A proximity or photoelectric sensor node can use the LT3669HUFD#PBF to combine IO-Link communication and regulated auxiliary power in a compact 28-QFN implementation. The integrated 16 V step-down output and 150 mA LDO reduce the number of discrete supply blocks needed near the sensor interface. With operation extending to 150 °C in verified comparison data, the H-grade device is relevant to high-temperature industrial installations. Final sensor current, cable voltage drop, and startup timing must be checked against the selected sensor and cable specification.
おすすめ
Factory Actuator Interface
The LT3669HUFD#PBF is appropriate for actuator interface electronics that need robust IO-Link data communication and local power regulation. Its rugged line drivers and verified ±60 V cable-interface protection suit industrial connection requirements better than a general-purpose logic interface. The integrated power blocks can support auxiliary circuitry without requiring a separate step-down converter and 150 mA LDO. Designers must account for inductive loads, contactor transients, grounding, and any protection components required outside the transceiver.
おすすめ
Remote I/O Module
In a compact remote I/O module, the LT3669HUFD#PBF can combine one IO-Link channel with regulated local power and timed startup. Wake-up detect can support activity-based behavior, while the programmable power-on reset timer can sequence downstream loads after the interface stabilizes. The 28-QFN format preserves board area compared with separate PHY, switching regulator, and LDO implementations. The module should still provide tested surge and ESD networks at the cable boundary and adequate copper thermal management beneath the exposed pad.
おすすめ
Industrial Motor-Control Interface
The LT3669HUFD#PBF can serve as the communication and local supply block in motor-control electronics that expose IO-Link accessories. Its integrated 16 V step-down regulator and 150 mA LDO organize lower-voltage control power, while COM1, COM2, and COM3 compatibility allows deployment across supported IO-Link modes. The stated −40 °C to 150 °C range is valuable near power stages, although the complete assembly must remain within component and enclosure limits. Keep noisy switching-node copper away from cable inputs and sensitive control returns.
おすすめ
Process-Control Sensor Node
For process-control sensor nodes, the LT3669HUFD#PBF offers IO-Link connectivity together with integrated local power conversion. The device's 7.5 V to 40 V operating range can simplify architecture where power arrives from an industrial field bus, and the 150 mA LDO can supply low-power sensing electronics. Wake-up detect and programmable power-on reset provide useful control behavior for remote nodes. Accurate measurement performance remains dependent on sensor excitation, grounding, filtering, and isolation rather than the integrated interface regulator alone.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: LT3669HUFD#PBF — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | LT3669EUFD#PBF | LT3669EUFD-2#PBF | LT3669HUFD-2#PBF |
|---|---|---|---|---|
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Package | QFN-28 with exposed pad | QFN-28 with exposed pad | QFN-28 with exposed pad | QFN-28, 4 mm × 5 mm |
| Product Type | IO-Link transceiver with integrated step-down regulator and LDO | IO-Link transceiver with integrated step-down regulator and LDO | LT3669-2 IO-Link transceiver | LT3669-2 IO-Link transceiver |
主な差別化要因
- Higher verified temperature ceiling than the E-grade option （vs LT3669EUFD#PBF)
- Combines IO-Link, 16 V step-down conversion, and 150 mA LDO functions （vs LT3669HUFD-2#PBF)
- Documented 28-QFN industrial interface package （vs LT3669EUFD#PBF)
設計ノート
Follow the current Analog Devices LT3669 datasheet layout for the 28-QFN exposed pad, input capacitors, 16 V step-down output, LDO output, and cable-side pins. Keep the switching node compact and away from the IO-Link receive path, because coupling from a high-dV/dt node can corrupt communication. Provide uninterrupted ground and thermal-pad vias, use short high-current return paths, and keep external cable-protection components close to the connector. The verified snippets do not include a recommended land pattern, so this record does not invent one.
Estimated: assess the regulator's thermal burden from P = (VIN - VOUT) × ILOAD using the final minimum bus voltage, regulated output, and worst-case load. For example, at 40 V input, 16 V output, and a hypothetical 150 mA load, the ideal buck-converter loss input is approximately 3.6 W before switching, conduction, and efficiency losses; this is an engineering estimate, not a verified datasheet value. Verify inductor saturation, capacitor ripple current, current limit, startup behavior, and the exposed-pad thermal margin with actual component data.
Do not assume that a shared LT3669 suffix proves pin-for-pin interchangeability. The -2 family variants may differ in timing or reset behavior, and the E versus H grade can change the maximum operating temperature from 150 °C to 125 °C. Before replacing LT3669HUFD#PBF, compare every package pin, exposed-pad connection, supply limits, IO-Link thresholds, regulator compensation requirements, output currents, reset timing, and package drawing in the current manufacturer datasheets.
The verified ±60 V cable-interface protection rating is not permission to remove external surge and ESD protection. Industrial cables can impose transients beyond normal supply conditions, so retain the protection network specified by Analog Devices, connect it close to the cable entry, and provide a low-impedance chassis or signal-ground return. Validate wake-up behavior, retry logic, and downstream reset timing with the worst-case cable, sensor capacitance, and power interruptions rather than only bench conditions.
コンプライアンス情報
A comparison page mentions RoHS details, but the supplied verified snippets do not state a definitive compliance result. The PBF suffix and #PBF lead-free finish notation are present in the MPN, but lead-free, halogen-free, REACH, AEC-Q100, and conflict-minerals status are not explicitly established by the provided text.
