集積回路

サブカテゴリ

📁 ADC/DAC 3,100+ 製品 📁 アンプIC 1,900+ 製品 📁 オーディオコーデック 18 製品 📁 オーディオIC 2 製品 📁 クロック＆タイミング 660+ 製品 📁 Comparator ICs 1 製品 📁 DSP 1,100+ 製品 📁 データ収集IC 2 製品 📁 デジタルポテンショメータ 4 製品 📁 ディスプレイドライバ＆コントローラ 1 製品 📁 FPGA & CPLD 7,300+ 製品 📁 インターフェースIC 3,300+ 製品 📁 LEDドライバ 1 製品 📁 ロジックIC 460+ 製品 📁 メモリIC 870+ 製品 📁 マイクロコントローラ 20,000+ 製品 📁 マイクロプロセッサ 4 製品 📁 モータドライバ 1 製品 📁 その他 1 製品 📁 Sensor and Detector Interfaces 1 製品 📁 専用IC 15 製品 📁 ビデオIC 14 製品

製品 (39,000+)

MC33079D - 15 MHz Low-Noise Quad Op Amp | onsemi
MC33079D

MC33079D - 15 MHz Low-Noise Quad Op Amp | onsemi

onsemi MC33079D is a low-noise, quad operational amplifier with four amplifiers in a 14-pin SOIC package. Its headline specifications are 4.5 nV/√Hz voltage-noise density, a 15 MHz gain-bandwidth product, and a 7 V/µs slew rate. The MC33079 uses bipolar input transistors and is intended for audio and data-signal processing applications requiring low noise, high-frequency response, low distortion, and stable operation. An operational amplifier, or op amp, is a high-gain differential amplifier whose external feedback defines its gain and bandwidth. Within the semiconductor hierarchy, an op amp belongs to the linear amplifier and analog signal-conditioning categories. It is used to amplify weak sensor signals, buffer high-impedance sources, implement active filters, and provide gain in audio and control paths. The MC33079 integrates four amplifiers in one package, reducing board area while providing consistent device-level matching. The MC33079D combines 4.5 nV/√Hz low-voltage-noise performance with a 15 MHz gain-bandwidth product. Its 7 V/µs slew rate supports faster large-signal transitions than slower general-purpose amplifiers. Additional features include 0.002% distortion, a large output-voltage swing, 2 kV ESD protection, and a macromodel for simulation. These characteristics make the device relevant to microphone preamplification, active audio crossover networks, audio buffer stages, and precision low-frequency signal conditioning. The bipolar architecture uses high-frequency PNP input transistors to provide low input-voltage noise. Because the amplifiers are not rail-to-rail, system designers should verify input common-mode range and output swing against the selected supply voltage. The listed operating-voltage range of 2.5 V to 15 V permits operation from low-voltage analog systems through conventional ±15 V bipolar supplies. The four amplifiers share a common package, although each output still requires suitable output-current and stability analysis for its load. Typical uses include four-channel audio buffering, low-level microphone amplification, active equalization, filtering, instrumentation interfaces, and general-purpose analog signal processing. In multi-amplifier designs, adjacent channels can implement gain, filtering, and drive functions without requiring four separate packages. The device can also serve in laboratory and industrial control circuits where low noise and a 15 MHz bandwidth are more important than rail-to-rail input or output operation. The primary design consideration is power-supply configuration. Decouple each supply connection with a local ceramic bypass capacitor, maintain a short return path, and place input and feedback components close to the relevant amplifier pins. Avoid using the quad amplifier merely because four circuits are required: confirm common-mode limits, output-swing headroom, capacitive-load stability, noise-gain bandwidth, and channel-to-channel layout symmetry before releasing the PCB. This product record combines the MC33079D manufacturer-datasheet specifications, package information, search queries, and cross-reference findings with practical design guidance. It also highlights genuine replacement constraints: a mechanically similar 14-pin SOIC amplifier is not automatically a drop-in replacement, so common-mode range, bias current, stability, noise, and exact pin assignment must be checked before substitution.

見積もり お問い合わせ
MC33079N - Low-Noise Quad Op Amp | STMicroelectronics | Audio
MC33079N

MC33079N - Low-Noise Quad Op Amp | STMicroelectronics | Audio

STMicroelectronics MC33079N is a monolithic quad operational amplifier designed for audio and general signal-processing applications, with four amplifiers in a 14-pin DIP package. Its headline characteristics are 4.5 nV/√Hz voltage noise, a 15 MHz gain-bandwidth product, and a 7 V/µs slew rate. The device is intended for designs that require low-noise signal amplification with sufficient bandwidth to handle audio signals and other low-frequency waveforms. An operational amplifier is a voltage-gain building block used throughout analog electronics. The MC33079 belongs to the op-amp hierarchy, where it provides amplification, buffering, filtering, and active gain for analog signals. Its four amplifiers share a common power supply in one package, allowing one quad device to implement several stages of an audio preamplifier, mixer, line amplifier, or measurement circuit while reducing board area. The MC33079N combines low voltage noise with high-frequency performance. The 4.5 nV/√Hz noise density supports low-noise audio amplification, while the 15 MHz gain-bandwidth product provides useful bandwidth for audio-frequency closed-loop designs. A 7 V/µs slew rate supports large-signal reproduction and reduces the likelihood of slew-rate distortion in higher-gain stages. The manufacturer also specifies very low distortion of 0.002%, along with strong phase and gain margins. Its four-circuit organization provides flexibility for mixed-signal layouts. Each amplifier can perform a separate function, such as input amplification, active filtering, buffering, or output drive, when the system does not require all four stages simultaneously. Since this is an analog integrated circuit, its performance depends on suitable bypass capacitors, stable feedback networks, appropriate source and load impedances, and careful consideration of common-mode and output-voltage limits. Typical uses include stereo and multichannel audio preamplification, active crossover networks, microphone and line-level signal conditioning, servo-control loops, and instrumentation requiring multiple amplifiers. The quad format can also reduce component count by replacing several individual single or dual amplifier packages. Where an existing amplifier section uses an equivalent 14-pin quad footprint, the MC33079N can serve as a focused upgrade for lower-noise audio operation after checking pin functions and operating limits. Design the supply rails to remain within the device's operating requirements and place the bypass capacitors close to the power pins. Keep feedback loops short, use resistors and capacitors suitable for the intended audio bandwidth, and verify stability with the selected gain and load. An oscilloscope measurement of output clipping, noise, and slew behavior can confirm that the overall circuit, rather than the op amp alone, meets the system specification. This page organizes the MC33079N's principal electrical characteristics, package details, application guidance, drop-in replacement options, and engineering trade-offs. It is designed to help engineers evaluate noise, bandwidth, slew rate, distortion, and compatibility before integrating the amplifier into an audio or precision analog design.

見積もり お問い合わせ
MC33102P - Dual 100nA 1.7V/us Operational Amplifier | Onsemi
MC33102P

MC33102P - Dual 100nA 1.7V/us Operational Amplifier | Onsemi

The onsemi MC33102P is a dual operational amplifier with a two-state Sleep-Mode architecture, combining two amplifier channels in an 8-pin PDIP package. It is designed for low-power signal conditioning where the amplifier can remain in a low-power sleep state while waiting for an input signal and switch to an awake state when amplification is required. The device is specified as a micropower operational amplifier with 100 nA supply current, 1.7 V/us slew rate, and 4.6 MHz gain-bandwidth product. An operational amplifier is an active analog signal-conditioning component that uses high-gain differential amplification to increase the voltage level of a weak or small signal. A dual operational amplifier contains two amplifier sections in one package, allowing two related signals to be processed simultaneously while reducing board area. The MC33102P adds Sleep-Mode technology to this familiar amplifier function, making it useful in portable instruments, sensor interfaces, battery-powered systems, and other applications where standby consumption matters. The MC33102P's main features include dual general-purpose amplifier channels, a sleep-mode operating state, an awake-mode operating state, 100 nA supply current, 1.7 V/us slew rate, and 4.6 MHz gain-bandwidth product. The low supply current supports designs that spend significant time monitoring or waiting for a valid input. The sleep and awake states provide a mechanism to control when the amplifier is intended to respond to signal activity. The dual configuration allows the part to handle two amplifier functions in one package, such as signal conditioning for two sensor channels, an instrumentation front end, or gain stages around a comparator and data-conversion system. The 4.6 MHz gain-bandwidth product supports moderate-bandwidth applications, while the 1.7 V/us slew rate provides useful response for slowly varying and low-to-moderate-frequency analog signals. Its PDIP-8 package is suitable for conventional through-hole PCB assembly and prototyping. When designing around the MC33102P, check the input common-mode range, output swing, supply-voltage limits, stability requirements, and the meaning of the sleep-mode control behavior in the manufacturer datasheet. Place the device close to the signal source when handling high-impedance nodes, provide normal bypassing at the supply pins, and account for input bias-current errors and offset voltage when resolving low-level signals. This product page combines the MC33102P device identity, package information, operating characteristics, sourcing guidance, comparison framework, and practical design notes. The information is intended to help engineers confirm pin compatibility, assess the dual low-power amplifier architecture, and select a suitable replacement or design approach without treating a different package or electrical function as a drop-in substitute.

見積もり お問い合わせ
MC33121P - Low-Voltage SLIC Interface | Motorola | PBX
MC33121P

MC33121P - Low-Voltage SLIC Interface | Motorola | PBX

The Motorola MC33121P is a low-voltage Subscriber Line Interface Circuit (SLIC) designed to connect the four-wire side of a central office or PBX to a two-wire subscriber line in a 14-pin plastic DIP package. It provides battery feed, loop-termination AC impedance, hookswitch detection, adjustable transmit, receive, and transhybrid gains, and single or double fault indication. The verified MC33121P listing identifies a 14-PDIP package, while the available technical material specifies a minimum longitudinal balance of 58 dB. A Subscriber Line Interface Circuit, or SLIC, is an integrated telecommunications interface that replaces many discrete functions associated with a analog telephone line. In the broader hierarchy, it is a specialized line interface IC within interface ICs and telecommunications semiconductors. It bridges a central-office or PBX voice path and a subscriber loop while separating transmit and receive signals, supporting line termination, and exposing hookswitch and fault information to the surrounding codec or control electronics. The MC33121P integrates several line-facing functions into one device. Battery feed supplies the line, while proper loop termination establishes the intended AC impedance seen by the subscriber. Adjustable transmit, receive, and transhybrid gains allow the surrounding system to control voice-path levels and balance. Hookswitch detection reports line activity, and separate status outputs indicate single or double faults, reducing the number of external discrete monitoring elements. Transmit and receive signals are referenced to analog ground, while digital status and control signals are referenced to digital ground. This separation simplifies interconnection with codecs, filters, and digital control logic. The hookswitch and fault outputs are compatible with TTL/CMOS, and the power-down input permits local shutdown. These interface features make the MC33121P suitable for integrated access, subscriber-line, PBX, voice codec, and central-office interface designs. Typical uses include a PBX line card, a central-office subscriber interface, a two-wire telephone-line interface, a voice codec interface, a hookswitch monitor, and a line-fault indication circuit. In each case, the IC provides the physical subscriber-line interface while external circuitry handles codec conversion, call control, supervision, and system-level power management. Because this legacy device is a through-hole 14-pin DIP, it is most practical for legacy designs, repair assemblies, and industrial or telecommunications equipment that can accommodate through-hole leaded components. Designers should preserve separate analog and digital grounding paths and connect the device to the selected codec, filter, and line-conditioning network exactly as shown in the manufacturer application material. Before production use, verify the unavailable operating voltage, temperature range, loop-current limits, external-component values, and absolute maximum ratings against the manufacturer datasheet. Those parameters are not supplied in the verified excerpts and therefore cannot be safely inferred. This page consolidates verified distributor pricing, package information, interface functions, comparison fields, and practical implementation cautions. It also distinguishes documented MC33121P characteristics from unverified alternatives, avoiding unsupported claims that a different SLIC is truly pin-to-pin compatible.

見積もり お問い合わせ
MC33171D - 1.8MHz Low Power Single Op-Amp SOIC-8 | STMicroelectronics
MC33171D

MC33171D - 1.8MHz Low Power Single Op-Amp SOIC-8 | STMicroelectronics

The STMicroelectronics MC33171D is a low-power single bipolar operational amplifier fabricated with quality bipolar processing and innovative design concepts, housed in an 8-pin SOIC package. It operates at 180 uA per amplifier, delivers a 1.8 MHz gain bandwidth product and a 2.1 V/us slew rate, and supports supply operation from 3 V to 44 V single-supply (or split supplies). An operational amplifier (op-amp) is an analog building block within the broader hierarchy of amplifier ICs and linear semiconductors. It amplifies the voltage difference between its inverting and non-inverting inputs with high open-loop gain, and its behavior in a circuit is set almost entirely by external feedback components. General-purpose op-amps such as the MC33171 series sit at the entry level of this taxonomy, below precision, high-speed, and instrumentation amplifier families, yet they remain the workhorse of analog signal conditioning. Key features of the MC33171 include its exceptionally low 180 uA supply current per amplifier, which makes it attractive for battery-powered and energy-conscious designs. The bipolar fabrication (without JFET device technology) gives robust input behavior and predictable industry-standard single-op-amp pinout. The wide 3 V to 44 V supply range allows operation from single low-voltage rails or from higher industrial buses, and the device is particularly suited for single-supply operation although it can run from split supplies. Technically, the MC33171/72/74 monolithic series combines the low static current with usable AC performance: the 1.8 MHz bandwidth covers audio and low-frequency instrumentation needs, while the 2.1 V/us slew rate supports moderate-amplitude signal swings without excessive distortion at those frequencies. Typical applications include battery-powered portable instruments, sensor signal conditioning, active filters, transducer amplifiers, and low-frequency comparators or level shifters in industrial control, where low quiescent drain and wide supply tolerance matter more than ultra-high speed. A key design consideration: because it is optimized for low power rather than high speed, allow adequate settling margin in feedback networks and avoid pushing large output swings near the 1.8 MHz bandwidth limit to prevent slew-induced distortion. This page adds value beyond the manufacturer datasheet by consolidating cross-brand availability context, drop-in alternative guidance, practical design notes, and sourcing access through the Request a Quote form.

見積もり お問い合わせ
MC33171N - 2.1MHz Low-Power Op Amp | STMicroelectronics
MC33171N

MC33171N - 2.1MHz Low-Power Op Amp | STMicroelectronics

STMicroelectronics MC33171N is a single bipolar operational amplifier with a 2.1 MHz gain-bandwidth product, 2 V/us slew rate, 200 uA supply current, and a DIP-8 package. It supports single-supply operation from 4 V to 44 V, while its input common-mode range extends to the lower supply rail. These characteristics make the MC33171N suitable for low-power analog signal conditioning, industrial instrumentation, sensor interfaces, and general-purpose voltage amplification. An operational amplifier is an analog integrated circuit that uses high open-loop gain to amplify differences between two input voltages. The bipolar MC33171N belongs to the operational-amplifier, analog-IC, and semiconductor hierarchy. Its rail-to-rail input common-mode capability is particularly useful in single-supply systems because the input signal can approach the lower supply rail without requiring a negative power source. The principal features are a 2.1 MHz gain-bandwidth product, a 2 V/us slew rate, and a typical supply current of 200 uA. The 2.1 MHz bandwidth provides useful bandwidth for general-purpose analog stages, while the 2 V/us slew rate limits how quickly the output can follow large voltage changes. Low 200 uA consumption supports battery-powered and distributed instrumentation designs where amplifier power can dominate the system budget. The MC33171N uses a single bipolar amplifier architecture rather than a JFET-input implementation. This architecture combines low supply consumption with moderate operating speed and makes the device appropriate for continuous analog signal processing without the static bias current associated with higher-performance precision amplifiers. Its 4 V to 44 V single-supply range allows operation from conventional 5 V and 12 V rails as well as higher industrial supply voltages. Typical applications include low-frequency instrumentation amplifiers, current-sensor signal conditioning, buffered sensor outputs, industrial control inputs, and low-power analog measurement systems. The input common-mode range extending to the lower rail is valuable in systems powered from a single positive supply, where input signals can be close to ground. Gain and bandwidth should be selected together so that the closed-loop noise gain remains compatible with the 2.1 MHz gain-bandwidth product. A key design consideration is the relationship between supply voltage, output swing, and input range. Confirm that the required signal and output remain inside the operating limits before assigning a high closed-loop gain. Keep feedback routing short, place input and supply bypass capacitors close to their relevant pins, and avoid extending high-impedance input traces where leakage and interference can degrade accuracy. This product page combines the STMicroelectronics MC33171 operating characteristics with package guidance, pin assignments, application analysis, verified drop-in alternatives, and practical circuit-design notes. It is intended to help engineers select the amplifier, confirm footprint compatibility, and plan an efficient single-supply analog implementation.

見積もり お問い合わせ
MC33171P - 3-44V Low-Power Op Amp | onsemi | 8-PDIP
MC33171P

MC33171P - 3-44V Low-Power Op Amp | onsemi | 8-PDIP

onsemi MC33171P is a single, general-purpose operational amplifier with a 3.0 V to 44 V supply range, low 180 uA operating current per amplifier, 1.8 MHz gain-bandwidth product, and 2.1 V/us slew rate. The device is packaged in an 8-pin plastic dual in-line package (8-PDIP). Its bipolar input stage provides a practical alternative to JFET-input amplifiers in applications that do not require JFET characteristics. An operational amplifier is an analog integrated circuit that amplifies the voltage difference between its inverting and non-inverting inputs. The MC33171 belongs to the operational-amplifier hierarchy within analog and mixed-signal semiconductors. It can operate from a single supply or split supplies, allowing it to serve as a general-purpose amplifier, buffer, comparator, or active-filter building block in industrial, instrumentation, and control circuits. Key characteristics include the wide 3.0 V to 44 V operating range, 180 uA current consumption per amplifier, 1.8 MHz gain-bandwidth product, and 2.1 V/us slew rate. These values position the device for low-power, moderate-bandwidth signal conditioning where a larger package is acceptable and through-hole assembly is preferred. The 8-PDIP format also simplifies prototyping, breadboarding, repair, and manual production processes. The bipolar fabrication approach provides the stated bandwidth and slew-rate performance without JFET-device technology. Because the operating supply extends to 44 V, the amplifier can accommodate higher-voltage systems than conventional low-voltage operational amplifiers. Designers must still verify input and output common-mode limits against the selected supply configuration before using the amplifier outside its intended operating region. Typical uses include low-frequency sensor conditioning, buffered transducer interfaces, audio preamplification, industrial control signals, power-supply feedback monitoring, and active analog filters. The 1.8 MHz gain-bandwidth product is suitable for many audio and instrumentation stages, while the 2.1 V/us slew rate supports reasonably clean responses to moderate-amplitude step inputs. When designing a board around the MC33171P, maintain adequate input and output voltage headroom, bypass the supply pins close to the device, and route high-impedance input signals with minimal leakage and contamination. Stable operation also depends on the feedback network, source impedance, output loading, and application-specific settling requirements. This product page combines the manufacturer's MC33171 family documentation, distributor package information, search-focused technical data, and practical design guidance. It also distinguishes verified drop-in alternatives from broader equivalents that may require different packages, supply ranges, or performance checks before substitution.

見積もり お問い合わせ
MC33172D - Low-Power Dual Op Amp | STMicroelectronics
MC33172D

MC33172D - Low-Power Dual Op Amp | STMicroelectronics

The STMicroelectronics MC33172D is a low-power dual bipolar operational amplifier with two amplifier circuits, a gain-bandwidth product of 1.8 MHz, and an 8-pin SOIC package. It is designed for general-purpose signal conditioning applications where two independent amplifiers are useful in a single package. An operational amplifier is a voltage-controlled differential amplifier that compares two input voltages and amplifies their difference. Operational amplifiers form part of the broader analog IC and active-signal-processing hierarchy. The MC33172D uses bipolar transistor input stages and is suitable for functions such as buffering, gain amplification, comparisons, filtering, and instrumentation interfaces when configured with suitable external resistors and capacitors. Each MC33172D channel provides a practical combination of low power consumption and general-purpose signal handling. The device contains two amplifier circuits in one 8-SOIC package, reducing component count and board area in designs requiring paired amplification. Its listed maximum input offset voltage is 6.5 mV, while its unity-gain bandwidth is 1.8 MHz. These characteristics suit signal paths that do not require the very low offset, very high bandwidth, or very low noise associated with specialized precision amplifiers. The bipolar architecture is appropriate for low-frequency control, measurement, and conditioning circuits where the amplifier operates mainly in a closed-loop configuration. Noise, offset, input common-mode range, output swing, supply current, and stability characteristics must be checked against the actual signal amplitude and frequency before the device is used. Negative feedback, adequate output loading, and input-referenced compensation should follow the manufacturer's recommended application circuits. Typical applications include dual-axis sensor signal conditioning, active filtering, audio preamplification, threshold detection, low-frequency instrumentation, and general industrial control. Two channels can also implement differential or complementary signal processing when their inputs and outputs are configured appropriately. The 8-SOIC package is easy to assemble with conventional surface-mount production equipment and can simplify upgrades compared with discrete single-amplifier packages. Designers should verify the supported supply voltage, common-mode input range, output swing, input bias current, and operating temperature against the manufacturer's datasheet. Input and output voltages must remain within the electrical limits, and unused amplifier inputs should be biased rather than left floating. Stable feedback-network values are essential at higher frequencies. This product page combines package details, searchable technical questions, application guidance, and a drop-in comparison focused on practical amplifier selection. It helps engineers distinguish the dual bipolar MC33172D from higher-speed rail-to-rail alternatives before committing a circuit board to an 8-SOIC footprint.

見積もり お問い合わせ
MC33172N - Dual 44V Low-Power Op Amp | STMicroelectronics
MC33172N

MC33172N - Dual 44V Low-Power Op Amp | STMicroelectronics

The STMicroelectronics MC33172N is a dual bipolar operational amplifier designed for low-power signal conditioning from single or dual supplies. It provides two amplifiers in an 8-pin PDIP package, operates from +4 V to +44 V, or equivalently from ±2 V to ±22 V, and is specified for approximately 200 µA per amplifier. The device offers 2.1 MHz gain-bandwidth product and a 2 V/µs slew rate for a practical balance of speed, power consumption, and operating range. An operational amplifier is an analog signal-processing IC that amplifies the voltage difference between its two inputs while using feedback to control gain, bandwidth, and output behavior. The dual-amplifier configuration places two independent amplifiers in one package, reducing board area in audio, instrumentation, industrial control, and sensor-interface circuits. MC33172N belongs to the bipolar operational-amplifier family within the broader voltage-regulator-free analog IC and semiconductor hierarchy. The headline electrical characteristics are its dual-amplifier architecture, 2.1 MHz gain-bandwidth product, 2 V/µs slew rate, and low supply current of approximately 200 µA per amplifier. These specifications make the device suitable for signals that require more bandwidth than a micropower-only amplifier but do not demand the very high speed or rail-to-rail performance of newer CMOS families. Its wide supply range also allows operation from conventional ±15 V and ±22 V analog rails. The MC3x172 series uses a bipolar input and output architecture rather than JFET input. This family construction supports operation from very low positive supplies through relatively high industrial voltage rails. Because the amplifiers are specified for both single- and dual-supply operation, the same device can be used in grounded single-supply designs, where the signal is biased around the midpoint of the supply, or in conventional dual-rail systems. Typical applications include low-frequency audio amplification, instrumentation-amplifier input stages, industrial sensor buffers, general-purpose signal conditioning, and power-supply feedback or monitoring circuits. The 8-pin PDIP package is mechanically straightforward for through-hole assembly and prototype work. The relatively low 200 µA-per-amplifier supply current is particularly useful when each active channel must remain powered continuously within a multi-channel measurement system. The principal design consideration is common-mode and output-range behavior. Designers should calculate signal swing, input bias requirements, and the effect of load current before fixing external resistor values. Because this is a bipolar amplifier rather than a rail-to-rail CMOS amplifier, input and output headroom must be checked against the selected supply voltage. Stable operation also depends on correct feedback topology and suitable output-load isolation. This product page combines the manufacturer datasheet with practical guidance for supply selection, signal conditioning, PCB implementation, and replacement assessment. It also distinguishes true pin-and-footprint-compatible options from broader functional equivalents so engineers can make a replacement decision without treating a similar amplifier as an automatic drop-in substitute.

見積もり お問い合わせ
MC33174D - Low-Power Quad Bipolar Op Amp | STMicroelectronics
MC33174D

MC33174D - Low-Power Quad Bipolar Op Amp | STMicroelectronics

STMicroelectronics MC33174D is a low-power quad bipolar operational amplifier with 200 uA supply current per amplifier, 2.1 MHz gain-bandwidth product, and 2 V/us slew rate. The device is offered in a 14-pin SOIC package and supports single-supply operation from +4 V to +44 V. Its input common-mode range extends to the lower supply rail, making it useful in low-side sensing and single-supply signal chains. An operational amplifier, or op amp, is a high-gain analog building block used to amplify, buffer, filter, compare, and control voltage signals. MC33174D belongs to the broader amplifier IC, analog IC, and semiconductor hierarchies. Unlike an amplifier built around JFET input devices, this bipolar implementation combines low supply consumption with useful low-frequency bandwidth and slew performance for general-purpose analog signal conditioning. The four amplifiers provide flexible circuit partitioning for industrial instrumentation, sensor interfaces, active filters, and control loops. Key characteristics include 200 uA supply current per amplifier, 2.1 MHz gain-bandwidth product, and 2 V/us slew rate. The input common-mode range reaches the lower supply rail, which simplifies designs powered from a single positive rail while the signal approaches the lower operating limit. Operation from +4 V to +44 V gives the device broad supply-voltage flexibility. The 14-pin SOIC package supports conventional surface-mount assembly, while the quad channel count consolidates four amplifiers into one component. The manufacturer datasheet identifies the MC3x174 family as low-power bipolar operational amplifiers that combine low consumption with improved speed compared with basic general-purpose bipolar alternatives. Typical uses include low-side current sensing, buffered sensor outputs, precision signal conditioning, sample-and-hold circuits, active filters, and low-frequency control loops. The extended lower-rail common-mode capability is particularly valuable when a measurement begins near ground and the circuit has only one positive supply. Split-supply operation remains possible where bipolar signals or output swing are required. Designers should verify input and output voltage limits, common-mode range, output-load capability, and stability requirements against the manufacturer datasheet for the operating condition. Decoupling capacitors should be placed close to the supply pins, and each amplifier stage should be checked for output saturation during startup and overload transients. This page organizes the MC33174D specifications, package information, verified sourcing context, drop-in alternatives, comparison parameters, and application guidance into one engineering-focused reference. It also identifies the limits of the available cross-reference information so replacement decisions can be made without treating merely similar amplifier families as confirmed drop-in devices.

見積もり お問い合わせ
MC33174N - Low Power Quad Bipolar Op-Amp, 2.1MHz | STMicroelectronics
MC33174N

MC33174N - Low Power Quad Bipolar Op-Amp, 2.1MHz | STMicroelectronics

The STMicroelectronics MC33174N is a quad bipolar operational amplifier in a 14-pin PDIP package, combining a low supply consumption of 200 uA per amplifier with a gain-bandwidth product of 2.1 MHz and a slew rate of 2 V/uS, while operating from a single +4 V to +44 V rail. The input common-mode range extends down to the lower supply rail, which allows the four amplifiers to be used directly in single-supply systems where the signal sits near 0 V. An operational amplifier (op-amp) is a voltage-amplifier building block whose gain, bandwidth and accuracy are shaped by negative feedback around a high-gain differential input stage. The MC3x174 family is built with monolithic bipolar fabrication and provides four amplifiers in a single package, making it a member of the analog amplifier IC hierarchy: op-amp -> quad operational amplifier -> analog amplifier IC -> analog semiconductor. Because four amplifiers share one package, a quad device reduces board area, decoupling capacitor count and total part count compared with four discrete single amplifiers. Key features of the MC33174N include the 200 uA low-consumption bias current that suits battery-fed and low-leakage measurement systems, the 2.1 MHz gain-bandwidth product that supports audio-band and general instrumentation signal paths, and the 2 V/uS slew rate that limits large-signal distortion on fast transients. The wide +4 V to +44 V supply span covers industrial 24 V rails, telecom 48 V style environments and split-supply laboratory setups from a single part family, and the rail-to-rail-referenced input stage avoids the need for a mid-supply bias network. Technically, the MC33171/72/74 series uses quality bipolar fabrication with high open-loop gain and 2.1 V/uS slew rate without relying on JFET input devices, which keeps input bias current low and stable while preserving moderate input impedance. The monolithic quad arrangement also means a common die and a common bias network, so all four channels track closely in offset and bandwidth. Because the package is a through-hole PDIP-14 with generous lead spacing, the part is easy to prototype on perfboard and to socket in legacy industrial equipment where surface-mount footprints are impractical. Typical applications include low-power sensor signal conditioning on 24 V industrial loops, battery-powered portable instrumentation, active filters and audio input stages, and general-purpose amplification inside test and measurement equipment. The 44 V maximum supply also allows the part to sit directly behind a protected 24 V or 36 V field wiring with additional headroom for transients. When designing with the MC33174N, note that the amplifier is intended for single-supply operation from +4 V, and while the common-mode input range reaches the lower rail, the output swing and offset behavior near that rail still deserve checking against the signal range you need. Decouple the supply pins close to the package, keep feedback resistors in the same range so noise and offset match, and confirm the input common-mode window in your specific gain configuration before relying on signals close to ground. This page consolidates the manufacturer datasheet parameters, package and pinout detail, plus drop-in replacement candidates and practical design notes, so that you can qualify the MC33174N for a new design or an obsolescence-driven substitution without hunting through multiple documents.

見積もり お問い合わせ
MC33178D - Low-Power Low-Noise Dual Op Amp | onsemi
MC33178D

MC33178D - Low-Power Low-Noise Dual Op Amp | onsemi

onsemi MC33178D is a low-power, low-noise dual operational amplifier designed for audio and data-signal processing applications. It is a monolithic bipolar amplifier using high-frequency PNP input transistors, an architecture selected to provide low input offset voltage, low noise, and low distortion. The device is offered in an 8-pin SOIC package and contains two amplifier circuits, allowing it to support common signal-conditioning tasks in compact analog designs. An operational amplifier is a voltage-amplifying component that uses negative feedback to create controlled gain, filtering, buffering, and signal-conditioning functions. The dual-amplifier configuration places two amplifiers in one package, reducing board area and simplifying designs that require two related channels. Within the broader semiconductor hierarchy, MC33178D belongs to the operational-amplifier family, which is part of the wider analog integrated-circuit and signal-processing categories. The MC33178/9 family combines bipolar transistor implementation with PNP input devices and an NPN output stage. This combination is particularly relevant to audio and general-purpose data processing because the input architecture is intended to reduce offset and distortion while maintaining a practical low-noise operating approach. Its dual-channel organization also makes the device applicable to small-signal amplification, filtering, buffering, and related analog front-end functions. The part can be used where two amplifier channels are needed at the same signal level or operating condition. Typical use cases include audio signal conditioning, low-level sensor amplification, active filtering, buffering, and general analog signal processing. The low-noise characteristic makes it relevant to designs in which the amplifier must preserve a small input signal without adding substantial unwanted noise, while the low-distortion architecture supports cleaner waveform reproduction. When designing around MC33178D, begin by confirming the required input common-mode range, output swing, gain-bandwidth behavior, input offset voltage, input bias current, and supply-current limits against the manufacturer datasheet. Decoupling capacitors should be placed close to the supply pins, and sensitive-input routing should avoid nearby switching nodes and high-current return paths. This page combines the manufacturer family information with package, sourcing, comparison, and design guidance to support initial component evaluation and PCB planning. MC33178D is therefore suited to engineers seeking a compact, dual-channel, low-power bipolar op amp for audio or data-signal processing. Its strongest differentiators are the combined low-noise and low-distortion architecture, dual amplifier integration, and 8-pin SOIC implementation. Confirm the exact electrical limits and environmental ratings for the finished design before release to production.

見積もり お問い合わせ
MC33199D - ISO 9141 Automotive K-Line Interface | NXP
MC33199D

MC33199D - ISO 9141 Automotive K-Line Interface | NXP

The NXP MC33199D is an ISO 9141 automotive diagnostic serial interface circuit with one driver and one receiver, designed for a 4.5 V to 5.5 V supply and packaged in a 14-SOIC. The device connects a vehicle microcontroller to the special K and L lines of an ISO diagnostic port. It provides a bidirectional K-line driver, an L-line receiver used during wake-up sequences, short-circuit protection for the K line, and over-temperature protection. An ISO 9141 interface is a dedicated diagnostic communication interface within the broader automotive network. ISO 9141 uses separate K and L conductors rather than a conventional multidrop CAN bus. The K line carries the main diagnostic communication waveform, while the L line helps establish the wake-up sequence. The MC33199D functions as the physical-layer interface between a microcontroller UART and these vehicle-network lines. Key specifications include 1 driver and 1 receiver, a 4.5 V to 5.5 V operating supply range, ISO 9141 protocol support, and a 14-SOIC package measuring 3.90 mm wide. The K-line driver is bidirectional and protected against short circuits and excessive temperature. The L-line receiver supports the diagnostic wake-up sequence, allowing the host controller to recognize and respond to bus activity. The MC33199D simplifies implementation of an ISO 9141 diagnostic port because the MCU can communicate through ordinary serial logic levels while the IC handles the vehicle K and L lines. Its single-driver, single-receiver arrangement is appropriate for one diagnostic channel. Protection of the K-line output reduces the risk of damage from an inadvertent bus short, although the external vehicle wiring, pull-up network, connector, and transient environment still require careful engineering. Typical applications include automotive diagnostic interfaces, engine-control units, transmission controllers, body-control modules, garage-door and service-tool testers, and other embedded systems that emulate or access ISO 9141 diagnostic ports. The device is most appropriate for legacy diagnostic systems rather than new designs centered on CAN, CAN FD, or LIN. When designing around the MC33199D, verify the K-line and L-line interface network, supply decoupling, grounding, and protection required by the vehicle platform. The 5 V supply range excludes direct 3.3 V operation. Because the part is identified as obsolete in the available replacement information, engineers should also evaluate the NXP-recommended MC33660B replacement against footprint, protocol, timing, and protection requirements before committing to a redesign. This product summary consolidates the verified protocol, electrical, package, lifecycle, replacement, pricing-reference, and design information for engineers evaluating the MC33199D. It also distinguishes verified values from specifications that require confirmation from the manufacturer datasheet, avoiding unsupported assumptions about pin assignments or unqualified substitutes.

見積もり お問い合わせ
MC33201D - 12V Rail-to-Rail Operational Amplifier | onsemi
MC33201D

MC33201D - 12V Rail-to-Rail Operational Amplifier | onsemi

The onsemi MC33201D is a single-circuit, low-voltage, rail-to-rail input and output operational amplifier packaged in an 8-pin SOIC. It operates from a maximum 12 V supply, accepts input voltages up to 200 mV beyond either supply rail without output phase reversal, and produces an output that can swing to within 50 mV of each rail. These characteristics allow analog signals to use nearly the complete supply-voltage range. A rail-to-rail operational amplifier is an analog signal-conditioning amplifier whose input common-mode range and output voltage range extend close to the positive and negative supply rails. In the broader semiconductor hierarchy, an operational amplifier belongs to the amplifier IC and analog signal-processing categories. It can amplify sensor signals, buffer high-impedance sources, compare voltages, or integrate feedback networks around a single analog signal path. The MC33201D combines rail-to-rail input operation with low-noise, high-output-drive characteristics. Its input stage accepts common-mode signals beyond the nominal supply rails by as much as 200 mV without reversing the output polarity. Its output stage can approach each supply rail within 50 mV, improving usable output swing in low-voltage systems where conventional fixed-range amplifiers leave little headroom. The device is designed for low-voltage analog systems in which common-mode and output range are more important than using a larger, higher-voltage amplifier. Rail-to-rail behavior is particularly useful when a sensor output can move close to a low supply rail, when an ADC or DAC must be driven near the end of its input range, or when a bipolar signal must be handled with a single positive supply. The manufacturer documentation identifies the MC33201, MC33202, MC33204, NCV33201, NCV33202, and NCV33204 as members of the same operational-amplifier family. Typical uses include portable instrumentation, sensor interfaces, low-voltage audio paths, ADC input conditioning, current monitoring, and general-purpose signal amplification. In each case, the designer should verify input bias current, offset voltage, bandwidth, output-current capability, noise, stability, and operating-temperature limits against the manufacturer datasheet before fixing the circuit. The most important design consideration is to preserve the amplifier's stability and rail-to-rail performance. Keep feedback components close to the device, avoid excessive capacitive loading on the output, and account for common-mode behavior in the region where the input stage transitions between internal transistors. Decoupling capacitors should be connected directly between each supply pin and the appropriate ground reference. This product record combines the manufacturer family information with package, function, commercial, comparison, and application guidance. It also identifies same-footprint family options for designs that can tolerate their different input-offset characteristics, while making clear that final substitution requires electrical verification in the target circuit.

見積もり お問い合わせ
MC33202D - Dual Rail-to-Rail Op Amp | onsemi
MC33202D

MC33202D - Dual Rail-to-Rail Op Amp | onsemi

The onsemi MC33202D is a dual rail-to-rail operational amplifier designed for low-voltage operation from 1.8 V to 12 V, supplied in an 8-pin SOIC package. The MC33202D contains two amplifier channels, supports rail-to-rail operation at both the input and output stages, and is specified for an ambient temperature range of -40°C to +105°C. These characteristics position it for compact, low-voltage signal-conditioning systems requiring one package to implement two analog channels. An operational amplifier is an analog integrated circuit that compares an input signal with a feedback-defined reference and amplifies the difference between them. In the broader hierarchy, the MC33202D belongs to the operational-amplifier class, then to the amplifier-IC category, and ultimately to the semiconductor and signal-processing markets. Rail-to-rail input operation allows the input common-mode range to extend toward the supply rails, while rail-to-rail output operation improves dynamic range when the output must approach either supply limit. The primary headline features are the 1.8 V to 12 V supply range, dual-channel configuration, and rail-to-rail input and output capability. The 8-pin SOIC package provides a conventional surface-mount footprint suitable for standard PCB assembly methods. Its -40°C to +105°C temperature range makes it relevant to industrial, instrumentation, communications, and consumer applications that require operation across an extended temperature span. MC33202D belongs to the MC33201/MC33202/MC33204 family of low-voltage, rail-to-rail operational amplifiers. The family architecture is intended for low-voltage analog systems in which signal levels may occupy much of the available supply range. Because the device is supplied in a dual amplifier configuration, a complete two-channel circuit can be implemented without selecting two separate single-channel packages, reducing board area and simplifying component procurement. Typical applications include sensor-signal conditioning, low-voltage audio and communications paths, transducer amplification, general-purpose voltage amplification, and dual-channel filtering or feedback networks. For instrumentation applications, the rail-to-rail input characteristic can reduce the need for additional mid-supply biasing when signals vary over a broad range. In communications systems, the low operating voltage can simplify compatibility with modern low-voltage supply rails. Design the surrounding decoupling, input common-mode range, output load, and stability network carefully. Place the power-bypass capacitor close to the supply pins, maintain the device within its specified supply-voltage and temperature limits, and verify the intended feedback topology across the required signal bandwidth. The manufacturer datasheet should be used as the controlling reference for electrical characteristics, limit values, and test conditions. This page organizes the MC33202D datasheet information, pin-compatible replacement candidates, package details, and engineering guidance in a form that helps designers evaluate the amplifier, compare drop-in options, and plan an 8-pin SOIC implementation without relying on generic amplifier-selection advice.

見積もり お問い合わせ
MC33204P - Quad Rail-to-Rail 1.8V Op Amp | onsemi
MC33204P

MC33204P - Quad Rail-to-Rail 1.8V Op Amp | onsemi

onsemi MC33204P is a four-circuit rail-to-rail operational amplifier designed for low-voltage signal conditioning and general-purpose analog systems. It operates from 1.8 V to 12 V and is packaged in a 14-pin plastic dual in-line package. The quad configuration provides four amplifiers in one device, reducing board area and simplifying designs that require several matched low-voltage signal stages. Rail-to-rail input and output operation allows the amplifier to use most of the available supply voltage. An operational amplifier is an analog integrated circuit that uses high-gain differential feedback to amplify small voltage differences between its inputs. The MC33204P belongs to the MC33201/MC33202/MC33204 family of low-voltage rail-to-rail amplifiers. Its differential input stage supports input voltages that may extend beyond the supply rails, while the output stage can approach both rails. This makes it useful where signal levels occupy a significant portion of the supply range. According to the onsemi product page, inputs can be driven as high as 200 mV beyond the supply rails without phase reversal on the outputs, and the output can swing within 50 mV of each rail. These figures are particularly useful when designing from a 1.8 V or 3.3 V rail. The four-amplifier arrangement supports independent gain stages, sensor interfaces, filters, comparators, and active feedback networks without requiring four separate packages. The common-mode input range is a defining feature of this amplifier family. Rail-to-rail input behavior lets a sensor output remain in the usable input range even when it approaches a supply rail. Output swing close to the rails increases the available dynamic range and can reduce the need for an additional output-biasing stage. Designers must still verify signal levels, output-load conditions, stability, and gain bandwidth for the selected operating point. Typical uses include portable sensor interfaces, industrial control and instrumentation, battery-powered monitoring, low-voltage data acquisition, active filters, and general analog signal conditioning. The quad package is particularly suitable when four similar amplifier functions are required. It can also support mixed functions, such as one buffer, two gain stages, and one comparator, although each channel's loading and stability requirements should be evaluated independently. For layout, route input and feedback connections away from output and supply paths to reduce coupling. Place bypassing capacitors close to the supply pins and maintain the feedback network close to the amplifier. Confirm the gain-bandwidth product and stability requirements for the intended closed-loop gain, especially when driving capacitive loads or operating with long PCB traces. This page combines the manufacturer specifications, package information, cross-reference findings, application guidance, and engineering trade-offs needed to evaluate the MC33204P for a new analog design. It also highlights where the quad pin-compatible LM348 may be considered and where its rail-to-rail performance must be checked before substitution.

見積もり お問い合わせ
MC33215BE - Voice-Switched Speakerphone IC | NXP
MC33215BE

MC33215BE - Voice-Switched Speakerphone IC | NXP

The NXP Semiconductors MC33215BE is a voice-switched speakerphone circuit, also identified as a telecom interface IC, in a 42-pin shrink dual inline package. The device integrates one voice-switched speakerphone circuit and is intended for telephone, intercom, and voice-communication equipment requiring local voice switching and speakerphone operation. Its specified operating temperature range is -20°C to 70°C. A speakerphone circuit is a voice-processing and interface category that connects a telephone or communications line to a microphone, loudspeaker, and related analog voice circuitry. Within the system hierarchy, the MC33215BE is a telecom interface IC, a type of integrated circuit used to translate and control analog voice signals between line and audio endpoints. Its 42-pin package provides the external connections needed for power, line interface, microphone, speaker, control, and signal-conditioning networks. The MC33215BE consolidates one complete voice-switched speakerphone function into a single IC rather than requiring several separate switching and interface blocks. This integration can simplify a telephone-terminal layout while reducing the number of separate active devices required for voice-path control. Designers should still use the manufacturer datasheet when assigning external networks, signal levels, supply limits, and control behavior to individual pins. The 42-pin shrink DIP package is suited to through-hole assembly and makes the MC33215BE attractive for legacy telephone equipment, handsets, intercom stations, and voice-terminal products assembled by insertion rather than surface-mount automation. Its package dimensions and lead spacing must match the board footprint, while adequate clearance should be maintained around neighboring analog components to reduce noise coupling and accidental soldering bridges. Typical applications include analog telephones, speakerphone terminals, intercom equipment, voice messaging appliances, and compact telephone-answering accessories. The device is also relevant to industrial voice panels and communications equipment that operates from -20°C to 70°C and needs a dedicated circuit for switching between microphone and loudspeaker voice paths. System-level EMC, line-interface protection, and audio feedback control remain separate design responsibilities. When designing around the MC33215BE, identify every external component by its datasheet reference and verify the selected package orientation before layout release. Do not infer pin functions from neighboring devices or generic telecom interfaces. Review the manufacturer application circuit for recommended coupling, filtering, and grounding arrangements, then verify the complete analog path on the assembled board. This page consolidates the confirmed device identity, package, temperature range, and circuit count with application guidance, sourcing answers, and engineering notes. It also clearly distinguishes confirmed manufacturer-facing information from parameters that must be obtained from the MC33215BE datasheet before schematic capture or production release.

見積もり お問い合わせ
MC33290D - ISO 9141 K-Line Serial Link Interface | NXP
MC33290D

MC33290D - ISO 9141 K-Line Serial Link Interface | NXP

The NXP (formerly Freescale) MC33290D is an ISO 9141 K-Line serial link bus interface IC housed in an 8-pin SOIC package, designed for bidirectional half-duplex communication between a vehicle's on-board microcontroller and off-board diagnostic equipment. The device is specified for an 8 V to 18 V supply range, with internal bus driver protection against sustained shorts and overtemperature conditions, and operates across -40 C to +125 C ambient temperature typical of under-hood automotive environments. An ISO K-Line transceiver is a specialized automotive interface device that converts logic-level UART signals into a single-wire, current-driven bus waveform compliant with the ISO 9141 physical-layer definition. Within the broader hierarchy, K-Line transceivers sit below CAN/LIN transceivers and above raw UART bridges as a legacy but still-required physical layer for emissions-related OBD-II communication defined by CARB and EU regulatory frameworks. Key features include a single-wire K-Line bus driver capable of sourcing and sinking bus current, internal thermal shutdown with hysteresis, integrated bus short-to-ground and short-to-battery protection on the bus pin, a wide operating voltage range to tolerate automotive load-dump transients, and a logic-level RX/TX interface that connects directly to a microcontroller UART. The IC's diagnostic mode draws minimal current when the bus is recessive, preserving quiescent power on always-on battery paths. Architecturally, the MC33290D integrates a high-side driver and a low-side driver on the K-Line bus pin, with a comparator-based receiver that distinguishes dominant (logic 0) and recessive (logic 1) bus states. A charge pump is not required because the device operates from the vehicle's nominal 12 V supply, simplifying BOM and PCB area. Typical applications include OBD-II diagnostic interfaces, scan-tool interfaces in service-bay equipment, ECU flashing stations, body controllers communicating with diagnostic testers, and aftermarket telematics units reading ECU K-Line parameters. A key design consideration is that the K-Line bus pin must be terminated with an external pull-up resistor to VBAT and protected against reverse battery by an external diode or smart power path. This is optional: the IC already includes internal bus protection, but external TVS diodes are recommended for production hardware. This page consolidates distributor pricing, drop-in alternatives, and design notes not found in the manufacturer datasheet to accelerate part selection for automotive diagnostic designs.

見積もり お問い合わせ
MC33388D - Fault-Tolerant CAN Interface | NXP | Automotive
MC33388D

MC33388D - Fault-Tolerant CAN Interface | NXP | Automotive

The NXP Semiconductors MC33388D is an automotive fault-tolerant CAN physical-layer interface with a 4.75 V to 5.25 V supply range, 5 mA supply current, and a 14-pin SOIC package. It supports differential CAN operation, ground shifts up to 1.5 V, dominant-state detection, receiver-mode control, failure detection, wake-up logic, slope control, and driver protection. These features position the device as a CAN physical-layer interface for automotive body-electronics multiplexing systems where ground-offset tolerance and fault resilience are important. A CAN physical-layer interface, also called a CAN transceiver, is the circuit that connects a CAN controller or host logic to a differential CAN bus. It belongs to the network-interface hierarchy: CAN transceiver to CAN physical layer to network interface IC to communication semiconductor. Unlike a controller-only device, the MC33388D handles bus-level signaling, driver protection, bus-state monitoring, and fault-oriented control functions required by demanding automotive environments. Verified product information identifies the MC33388D as an automotive fault-tolerant CAN interface and lists its 4.75 V to 5.25 V operating supply range, 5 mA supply current, and 14-SOIC package. Differential operation allows communication despite ground shifts up to 1.5 V and is intended to reduce radio-frequency-interference disturbances. The package also provides dedicated receiver-mode control, mux and failure-detection signals, standby and enable controls, wake-up inhibit, error indication, and slope-control functions. The device's architecture separates CAN bus-side signaling from logic-side control while adding automotive fault tolerance around the physical interface. Its 5 mA supply-current specification supports power-conscious body modules, while the 5 V supply range fits conventional automotive electronics. Ground-shift tolerance is particularly valuable when the transceiver and CAN controller reference different ground potentials or when common-mode voltage varies in body-network installations. Typical uses include automotive body-control modules, door and lighting controllers, seat and occupant-system electronics, climate-control nodes, sensing modules, and other distributed vehicle systems connected by a CAN bus. The fault-tolerant interface can also support industrial CAN equipment when its electrical ratings, automotive qualification status, availability, and lifecycle requirements have been verified for the target environment. Before layout, confirm the exact pin mapping and recommended external network in the manufacturer datasheet. Place the CAN bus-side network and protection components close to the transceiver pins, maintain a continuous ground reference where the architecture permits, and verify termination, common-mode voltage, bus-fault behavior, and timing in the final vehicle network. The available web results do not provide verified pricing, complete electrical limits, or a confirmed package drawing, so those details remain marked as data needed rather than inferred.

見積もり お問い合わせ
MC33390D - J1850 Class B Serial Transceiver | NXP
MC33390D

MC33390D - J1850 Class B Serial Transceiver | NXP

NXP Semiconductors MC33390D is a Class B serial transceiver designed for bi-directional, half-duplex data communications on an automotive SAE J1850 single-wire bus. The device operates from a 9 V to 16 V supply, supports data rates up to 10.4 kbps, and provides one driver and one receiver in an 8-SOIC package. Its primary function is to interface an on-board vehicle microcontroller directly with the J1850 Class B network. A serial transceiver is an interface IC that combines a transmitter and receiver so a host controller can exchange logic-level data with a physical bus. The MC33390D belongs to the automotive network-interface layer, where it translates between the controller interface and the electrical signaling required by the SAE J1850 Class B bus. This single-wire network arrangement reduces wiring complexity while supporting bidirectional communication over one physical conductor. The verified MC33390D specifications identify a 1/1 transceiver configuration, a 9 V to 16 V supply range, and operation at 10.4 kbps. These figures position the device for low-speed vehicle body and comfort systems rather than high-bandwidth automotive Ethernet. The 8-SOIC package is offered in tube packaging according to the available distributor specification, and the listed lead-free status states that the part contains lead. Typical automotive uses include body-control modules, instrument-cluster interfaces, door and lighting controllers, climate-control electronics, and other embedded vehicle systems that communicate through J1850 Class B. The MC33390D is most appropriate when the system already uses a J1850 network and requires a physical-layer transceiver between that bus and an on-board microcontroller. Designers must account for automotive transient immunity, grounding, bus termination, connector protection, and the voltage limits of the external MCU interface. The available verification data does not expose the complete pin-name mapping, absolute maximum ratings, ESD ratings, or recommended external-component values. Those details must be confirmed in the official NXP datasheet before schematic release or PCB sign-off. This page consolidates the verified manufacturer, distributor, and octopart records with package information, sourcing fields, application context, and a strict assessment of available drop-in alternatives. It distinguishes confirmed parameters from information requiring datasheet verification so procurement and engineering teams can make evidence-based decisions.

見積もり お問い合わせ
MC33399D - LIN Bus Half Transceiver | NXP | Automotive
MC33399D

MC33399D - LIN Bus Half Transceiver | NXP | Automotive

The NXP Semiconductors MC33399D is an automotive LIN bus physical-layer transceiver packaged in an 8-pin SOIC with a 0.154-inch, 3.90 mm body width. The verified product listing identifies the device as a one-transceiver, half-duplex LINbus interface, placing it in the hierarchy of LIN transceivers, physical-layer interface ICs, interface ICs, and automotive semiconductor devices. A LIN bus is a low-cost, single-wire communication network commonly used between automotive electronic control units. The MC33399D provides the physical interface needed to connect a host controller or microcontroller to that network. Its half-duplex arrangement supports bidirectional communication over the LIN conductor while allowing the host-side logic to manage request and response sequencing. The NXP listing identifies the part as an automotive LIN physical-layer transceiver, and a verified technical result associates it with the LIN transceiver category and AEC-Q100 automotive qualification. The MC33399D is supplied in an 8-SOIC package according to DigiKey, while distributor information specifies a body width of 0.154 inches, or 3.90 mm. This surface-mount format supports compact automotive electronic modules while retaining a widely used package family. The product is intended for vehicle electronic control units, body electronics, sensor interfaces, door modules, lighting controllers, and other low-speed distributed automotive systems. The primary design consideration is that LIN transceivers operate in a physically different environment from conventional high-speed interfaces. The bus is slower than CAN or Ethernet, but its single-wire topology, long cable runs, automotive transients, ground offsets, and shared-network behavior require careful PCB implementation. The transceiver should be placed near the connector or protected interface path, with its external protection and bus-connection components selected using the manufacturer datasheet and the vehicle platform requirements. Because the supplied web evidence establishes the MC33399D identity, interface role, automotive qualification association, and 8-SOIC package, but does not provide complete electrical limits, timing values, pin names, or a verified numeric price, those details remain intentionally unasserted. Engineers should download the manufacturer datasheet and validate absolute maximum ratings, supply limits, logic thresholds, LIN bus parameters, termination, protection, and recommended external components before schematic or PCB release. This page combines verified distributor information, source-traceable specifications, procurement guidance, interface-design considerations, and clearly qualified replacement analysis. It distinguishes documented facts from unavailable parameters so that an MC33399D design decision can be made without turning unverified values into engineering assumptions.

見積もり お問い合わせ
MC33502P - 1-7V Dual Rail-to-Rail Op Amp | onsemi
MC33502P

MC33502P - 1-7V Dual Rail-to-Rail Op Amp | onsemi

onsemi MC33502P is a dual operational amplifier designed for low-voltage signal-processing applications, with two amplifier circuits in an 8-pin PDIP package. It operates from 1 V to 7 V, supports rail-to-rail operation at both the input and output, and can swing its output to within 50 mV of either supply rail. These characteristics make it useful where the usable signal range must extend close to the positive and negative supply limits. An operational amplifier is an analog signal-conditioning component that uses differential input voltage to control an amplified output voltage. The dual-amplifier configuration provides two independent amplifiers in one package, reducing component count on boards that require two gain stages, buffers, comparators, or active-filter channels. In the MC33502P, rail-to-rail inputs help preserve signal range in single-supply systems, while the rail-to-rail output improves the available output swing. The principal features of the MC33502P are its 1 V to 7 V supply range, dual-circuit configuration, rail-to-rail input and output operation, and output capability within 50 mV of the rails. The 8-pin PDIP package supports conventional through-hole PCB assembly and is useful for prototypes, educational designs, and legacy equipment. Its dual topology also allows the two channels to operate in inverting, non-inverting, buffer, comparator, and filter configurations, subject to the operating limits in the manufacturer datasheet. At low supply voltages, amplifier headroom becomes a central design constraint. The MC33502P is intended for circuits operating from 1 V to 7 V, allowing it to serve portable sensors, low-voltage analog interfaces, battery-powered instruments, and mixed-signal embedded systems. Because a rail-to-rail output still does not reach the ideal supply rails, designers should account for the stated 50 mV output-swing limit when defining logic thresholds or low-amplitude signal ranges. Typical applications include low-voltage sensor conditioning, active filtering, microphone or audio preamplification, transducers with limited supply voltage, and general-purpose dual-stage amplification. The device can also implement two independent buffer channels where low quiescent consumption and compact through-hole assembly are useful. For new high-density products, the older PDIP format should be weighed against newer surface-mount dual op amps that can offer lower board area and automated assembly. When designing around the MC33502P, begin by checking the required input common-mode range, output load, gain-bandwidth behavior, slew rate, noise, and stability for the selected configuration. Keep feedback resistors and compensation components close to their associated pins, provide adequate input and output decoupling, and avoid driving capacitive loads without stability analysis. Review the manufacturer datasheet for the exact dual-pinout, electrical limits, and recommended operating conditions before releasing a production schematic.

見積もり お問い合わせ
MC33742DWR2 - SBC with HS-CAN Transceiver, SPI | NXP
MC33742DWR2

MC33742DWR2 - SBC with HS-CAN Transceiver, SPI | NXP

The NXP MC33742DWR2 is a System Basis Chip (SBC-E-HS) that integrates a 1 Mbps CAN 2.0-compliant high-speed CAN transceiver, a fixed 5.0 V low-dropout voltage regulator, a second external pass-transistor regulator, SPI control up to 4.0 MHz, and full automotive diagnostic and protection features, all packaged in a 28-pin SOIC (DW) wide-body surface-mount outline. The internal LDO delivers 5.0 V with current limiting and over-temperature pre-warning, while the auxiliary regulator drives an external PNP/Darlingtons for higher current loads. The CAN bus pins support bus-dominant time-out, thermal shutdown, and bus-failure diagnostics per ISO 11898-2/5. A System Basis Chip (SBC) is a multi-function automotive power-and-interface IC that consolidates a voltage regulator, CAN/LIN transceivers, watchdog, and SPI control into a single package - reducing PCB area in body, chassis, and powertrain ECUs versus discrete implementations. Architecturally the MC33742DWR2 sits between a discrete 5V regulator plus separate CAN transceiver and a full MCU integration, providing the regulator, bus driver, and housekeeping functions while leaving the host microcontroller external. Key features include 1 Mbps CAN bus interface with bus diagnostics, SPI control at frequencies up to 4.0 MHz, a 5.0 V fixed LDO with current limiting, over-temperature prewarning and reset, plus an auxiliary regulator through an external pass element. The device is designed to operate in automotive -40C to +125C ambient, supports wake-up via CAN bus or external signal, and provides protected bus pins tolerant to -27 V to +40 V. Typical applications include automotive body control modules, HVAC and instrument-cluster ECUs, door/seat/lighting modules, CAN node power conditioning, and industrial CAN-based distributed I/O. The 1 Mbps bus speed and integrated diagnostics suit on-vehicle networks requiring real-time fault reporting. When designing with this device, bypass the internal regulator with low-ESR ceramic and bulk capacitors sized for the load step, and keep the CAN bus stubs short to meet ISO 11898 signal-integrity margins. A series resistor on the bus may be needed to limit slew rate in non-isolated test setups. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes that are not consolidated on the manufacturer datasheet, including cross-brand options and AEO-optimized selection guidance for engineers.

見積もり お問い合わせ
MC33793D - Byte-Wide DSI Sensor Interface | NXP | 16-SOIC
MC33793D

MC33793D - Byte-Wide DSI Sensor Interface | NXP | 16-SOIC

The NXP Semiconductors MC33793D is a slave Distributed System Interface (DSI) sensor interface with a byte-wide parallel interface, optimized for connecting sensors such as accelerometers to an automotive or industrial controller. The device is offered in a 16-pin SOIC package and is supplied in a tube according to the verified distributor data. A Distributed System Interface, commonly abbreviated DSI, is a byte-wide serial bus intended for sensor communication. In the broader electronics hierarchy, a DSI sensor interface is an interface IC, a communications interface, and ultimately a semiconductor. MC33793D supports a sensor-oriented slave role and contains circuits that can power compatible sensors and digitize their analog output, reducing the amount of discrete conditioning circuitry required around a sensor. The verified product information identifies the MC33793D as a 16-SOIC device with logic inputs and logic outputs. Its byte-wide interface provides a structured pathway for transferring sensor data, while its sensor-specific integration can simplify implementations that would otherwise require separate analog-to-digital conversion, sensor excitation, and communication logic. The tube packaging also suits production processes that handle through-hole SOIC devices conventionally rather than reel-fed surface-mount assembly. The MC33793D family was originally associated with Motorola, Inc., and the part is currently listed by NXP USA Inc. through DigiKey. Historical search results also identify the MC33793 as a slave DSI device optimized for sensor interfacing. Because the supplied evidence does not expose detailed electrical timing, supply-voltage, sensor-excitation, conversion-resolution, or environmental limits, those values must be confirmed in the manufacturer datasheet before a new design is released. Typical uses include automotive accelerometer sensing, industrial motion and condition monitoring, and embedded systems that need a dedicated sensor-interface function close to the sensing element. In such designs, the interface helps consolidate sensor excitation and analog digitization while presenting a byte-oriented data path to the supervising electronics. Designers should verify the exact pin functions, recommended sensor interface, supply requirements, and signal timing from the MC33793 datasheet before layout release. PCB placement should preserve the manufacturer's guidance for sensor excitation and analog signal routing, while software and bus timing should be checked against the controller's DSI implementation. This page consolidates the verified package, interface, packaging, sourcing, and manufacturer-history information for MC33793D, adds practical application and design guidance, and clearly separates confirmed facts from electrical details that require datasheet verification.

見積もり お問い合わせ