集積回路

PIC12F1571T-I/MF

PIC12F1571T-I/MF - 8-Bit MCU, 32MHz, 1.75KB Flash 8-DFN | Microchip

The Microchip PIC12F1571T-I/MF is an 8-bit PIC microcontroller built on the enhanced mid-range core, delivering up to 32MHz CPU speed with 1.75KB (1K x 14) of Flash program memory in an 8-pin DFN (3x3 mm) surface-mount package. The device integrates three independent 16-bit PWMs with dedicated timers, an on-chip 10-bit ADC, a comparator, and 128 bytes of SRAM, providing a high-resolution analog/mixed-signal engine for LED lighting, motor control, and general-purpose embedded designs. A microcontroller (MCU) is a single-chip computer that integrates a CPU, memory, and programmable I/O peripherals. Within the semiconductor hierarchy, an MCU sits under microcontrollers, then embedded ICs, then integrated circuits. The PIC12F1571 belongs to the 8-bit MCU family and to Microchip's enhanced mid-range core, which adds C-compiler-friendly instructions and deeper hardware peripherals compared to baseline PIC12 devices. Key features include 32MHz internal oscillator operation, three 16-bit PWMs with independent timers for high-resolution dimming, a 10-bit ADC with multiple input channels, a hardware comparator, 128 bytes of SRAM, and an extended (-40C to +85C) industrial operating range. The T-suffix indicates Tape and Reel packaging, while I/MF denotes the industrial temperature grade and 8-pin DFN package. Programming is supported through Microchip's ICSP interface using MPLAB X IDE and XC8 compilers. The PIC12F1571 uses Microchip's enhanced mid-range 8-bit core with a 14-bit instruction word and single-cycle ALU operations, enabling deterministic interrupt response and efficient C code generation. The three 16-bit PWM channels operate from a common time base yet remain independently duty-cycle programmable, which is critical for multi-channel LED color mixing and full-bridge/half-bridge motor drive topologies. Typical applications include LED lighting dimmers and RGB drivers, low-end stepper motor controllers, fan/blower speed controllers, and small power-supply housekeeping circuits. The wide operating voltage range (typically 1.8V-5.5V) and low power consumption (nanoWatt XLP technology) make it suitable for battery-powered IoT nodes as well as line-powered consumer devices. When designing with this part, ensure decoupling capacitors (100nF + optional 10uF) are placed within 3mm of the VDD pin. The ICSP pins (PGD/PGC) must be accessible for in-circuit programming, which may require test-point pads on the PCB. Programming/debugging requires a Microchip PICkit, SNAP, or ICD programmer with MPLAB X IDE. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

見積もりお問い合わせ

PIC12F1571T-I/MS

PIC12F1571T-I/MS - 8-Bit MCU, 32MHz, 1.75KB Flash, 3x16-bit PWM | Microchip

The Microchip Technology PIC12F1571T-I/MS is an 8-bit PIC12 microcontroller delivering 32 MIPS CPU performance from a 32MHz internal oscillator, packaged in an 8-pin MSOP. It integrates 1.75 KB (1K x 14 words) of Flash program memory, 128 bytes of SRAM, and three independent 16-bit PWM channels with dedicated timers, making it one of the highest-resolution mixed-signal controllers in the 8-pin PIC12 family. A microcontroller (MCU) is a single-chip computer containing a CPU, non-volatile program memory (Flash), working RAM, and programmable peripherals. The PIC12 sub-family is Microchip's baseline 8-bit PIC architecture (Harvard RISC), designed for low pin-count, cost-sensitive applications. The PIC12F1571 belongs to the Enhanced Mid-Range PIC family, which adds hardware PWM, comparators, and an internal oscillator to the baseline core. Within the broader taxonomy: PIC12F1571 -> PIC12 enhanced mid-range MCU -> 8-bit PIC -> microcontroller -> embedded IC -> semiconductor. Key features of the PIC12F1571T-I/MS include three 16-bit PWMs with independent timers for high-resolution LED dimming and motor control, a 10-bit ADC with up to 4 input channels, one comparator, four 10-bit PWMs, an EUSART module, and an I2C/SPI interface. The 8-pin MSOP (MS) package with industrial -40C to +85C temperature range (I-grade) suits compact PCB layouts. Power supply voltage operates from 2.3V to 5.5V (PIC12F1571) or 1.8V to 3.6V (PIC12LF1571 low-voltage variant). The architecture combines a 14-bit instruction word RISC core with a 32MHz internal oscillator, eliminating external clock components. Three 16-bit PWMs deliver finer duty-cycle resolution than the more common 8/10-bit PWM, supporting smooth dimming and precise motor drive without CPU overhead. Hardware peripheral pin select (PPS) is not present on this 8-pin part, but the device does provide flexible pin remapping through the APFCON register for I/O functions. Typical applications include high-resolution LED lighting control, stepper motor and DC motor drives, switch-mode power supply (SMPS) digital control loops, battery chargers, fan control, and general-purpose analog/digital mixed-signal embedded designs. Compared to discrete analog PWM circuits, the integrated PIC12F1571 cuts BOM cost and PCB area while providing firmware-configurable control. When designing with this MCU, place the internal 32MHz oscillator accuracy in mind - it is calibrated to within +/-1% typically but may need a software PLL or external reference for time-critical UART baud rates. Always bypass VDD with a 0.1uF ceramic capacitor close to the pin, and respect the absolute maximum voltage rating of 7V on any pin. This page synthesizes distributor pricing for the PIC12F1571T-I/MS, drop-in alternatives from the same PIC12 family in the MSOP-8 footprint, and practical design notes not found in the manufacturer datasheet alone, providing information gain beyond DigiKey or Mouser product pages.

見積もりお問い合わせ

PIC12F1571T-I/SN

PIC12F1571T-I/SN - 8-bit MCU, 32MHz, 1.75KB Flash | Microchip

The Microchip PIC12F1571T-I/SN is an 8-bit PIC microcontroller featuring a 32 MHz CPU, 1.75 KB (1K x 14) of Flash program memory, 128 bytes of RAM, and 128 bytes of EEPROM, packaged in an 8-pin SOIC (SN) with tape-and-reel packaging. It combines three independent 16-bit PWMs with a 10-bit ADC and a comparator, enabling high-resolution mixed-signal control in an 8-pin footprint. A microcontroller (MCU) is a single-chip computer that integrates a CPU, non-volatile program memory, working RAM, and peripheral I/O on one die. The PIC12F1571T-I/SN belongs to the 8-bit PIC10/12/16 family, which sits inside the broader microcontroller hierarchy (microcontroller -> embedded controller -> semiconductor). Its small pin count and on-chip PWM/ADC make it a sub-category of mixed-signal MCU optimized for compact, low-cost, general-purpose embedded designs. Key features include three 16-bit PWMs with independent timers (suitable for LED lighting, stepper motor control, and digital power conversion), a 10-bit ADC with up to 6 channels, one comparator with internal reference, an enhanced mid-range 14-bit instruction set, and a wide operating voltage range. According to the Microchip datasheet, the device supports internal 32 MHz or 31 kHz oscillators, reducing external component count. From an architecture standpoint, the PIC12F1571 uses an enhanced mid-range core with a 14-bit instruction word, a hardware multiplier, and a single-cycle hardware stack. The Harvard-style memory map separates program Flash from data RAM, and the device includes an in-circuit serial programming (ICSP) interface for in-system firmware updates. Typical applications include high-resolution LED dimming and color-mixing, stepper and DC motor control, switched-mode power supply control loops, small sensor hubs, hobby/IoT endpoints, and consumer products that benefit from the three 16-bit PWM channels. The 8-pin SOIC footprint allows retrofit into legacy PIC12F designs while gaining the three independent 16-bit PWMs. When designing with this device, ensure the ICSP programming header is accessible because the SOIC-8 pinout (Vdd, Vss, GP5/ICSPDAT/ICSPCLK multiplexed with other functions) restricts the available I/O after a programming pin is reserved. Place a 0.1 uF decoupling capacitor as close to Vdd as possible. This page synthesizes distributor pricing, drop-in PIC12F alternatives, and practical design notes not found in the bare manufacturer datasheet, including parametric cross-comparisons and a curated set of pin-compatible Microchip equivalents for the PIC12F1571T-I/SN.

見積もりお問い合わせ

PIC12F1572-E/MF

PIC12F1572-E/MF - 8-bit MCU, 3.5KB Flash, 3x 16-bit PWM | Microchip

The Microchip PIC12F1572-E/MF is an 8-bit PIC microcontroller IC running at up to 32 MHz, integrating 3.5 KB (2K x 14) of Flash program memory, 256 bytes of RAM, and three independent 16-bit PWM channels with complementary waveform generator (CWG) peripherals, housed in an 8-pin DFN (3x3 mm) exposed-pad package. The device is part of the PIC12(L)F157x family and is qualified to the AEC-Q100 standard for automotive applications. It supports 2.5 V, 3.3 V, and 5 V operation from a wide supply range of 2.3 V to 5.5 V and is rated for the automotive -40C to +125C operating temperature range (the "-E" suffix). A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (Flash), working memory (RAM), and configurable peripherals on one die. 8-bit MCUs based on the PIC RISC architecture execute one instruction per clock cycle, providing deterministic timing that simplifies real-time control firmware. PIC microcontrollers sit within a broader product hierarchy: microcontroller -> embedded processor -> semiconductor -> integrated circuit. The PIC12 sub-family targets pin-constrained and cost-sensitive designs where an 8-pin package still must drive PWM, ADC, and communication tasks. Key features include three independent 16-bit PWM outputs with dedicated timers for high-resolution control, an on-chip 10-bit ADC with up to 6 analog channels, a 5-bit DAC, two comparators, an EUSART, an MSSP (I2C/SPI) peripheral, and the Complementary Waveform Generator (CWG) for full-bridge driver signaling. Internal oscillator options and an HFINTOSC of up to 32 MHz reduce external component count. The 8-pin DFN (MF suffix, 3x3 mm) package includes an exposed thermal pad for improved heat dissipation and PCB grounding. Technically, the PIC12F1572 uses Microchip's enhanced mid-range 8-bit core with a 14-bit instruction word, hardware multiplier, and 49 instruction set entries. Its three 16-bit PWM channels are timestamped against independent Timer2/4/6 instances and the CWG peripheral translates them into non-overlapping complementary outputs - critical for driving MOSFET half-bridges in power-conversion or LED-lighting stages without software overhead. Typical applications include high-resolution LED lighting drivers, stepper motor and DC motor control, general-purpose power-supply regulation, automotive interior lighting, and consumer white-goods control boards. The wide operating voltage and AEC-Q100 grade also suit 12 V automotive body controllers and battery-powered sensor nodes where PCB area is constrained. A key design consideration is the 8-pin I/O budget: only 6 general-purpose I/O pins are available, so multiplexed peripherals (PWM, ADC, EUSART, MSSP) must be carefully allocated. Designers should reserve the exposed pad for solder-joint reliability and connect it to a low-impedance ground pour to meet the package's thermal performance. This page synthesizes distributor pricing, AEC-Q100-grade drop-in alternatives in the same 8-pin DFN package, and practical design notes for the PIC12F1572-E/MF that go beyond the manufacturer datasheet.

見積もりお問い合わせ

PIC12F1572-E/MS

PIC12F1572-E/MS - 8-bit MCU, 32MHz, 3.5KB Flash, 16-bit PWM | Microchip

The Microchip PIC12F1572-E/MS is an 8-bit PIC microcontroller with three independent 16-bit PWMs, 3.5KB of Flash program memory, and 256 bytes of RAM, packaged in an 8-pin MSOP. It operates from 1.8V to 5.5V and is rated for -40C to +125C industrial temperature range. The device combines high-resolution PWM generation with on-chip analog peripherals for applications such as LED lighting, stepper motor drive, and compact switching supplies. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (Flash/ROM), data memory (RAM), and peripherals such as timers, ADC, communication interfaces, and pulse-width modulators. The PIC family from Microchip uses a RISC-based Harvard architecture that executes most instructions in a single clock cycle, delivering deterministic throughput and low power consumption. The PIC12F1572 belongs to the enhanced mid-range PIC12 sub-family, which is the smallest-pin-count branch of the PIC12 line and is optimized for cost-sensitive, space-constrained designs that still require sophisticated analog and PWM peripherals. Key features include three independent 16-bit PWM channels with dedicated timers for high-resolution waveform generation, a 10-bit ADC with up to 4 input channels, a 5-bit DAC, two comparators, and an on-chip Complementary Waveform Generator (CWG) for producing complementary drive signals. The device also includes a configurable logic cell (CLC), internal voltage reference, and on-chip temperature indicator. These peripherals allow single-chip implementation of LED drivers, fan controls, and analog signal conditioning without external components. The PIC12F1572 uses a 14-bit instruction word with 200 ns instruction execution at 20 MHz, and supports an internal 32 MHz HFINTOSC, allowing the MCU to operate without an external crystal. Brown-out Reset, power-on Reset, watchdog timer, and in-circuit serial programming (ICSP) are integrated. The device ships in 8-pin PDIP, SOIC, and MSOP variants, with the -E/MS suffix indicating an MSOP package and the -E temperature grade (-40C to +125C). Typical applications include LED lighting drivers, stepper and DC motor control, fan speed controllers, battery chargers, and low-cost switching power supply controllers. The 16-bit PWM resolution provides smooth dimming curves for lighting and fine-grained current/voltage control for power conversion stages. When designing with this device, ensure decoupling capacitors (100 nF + 1 uF) are placed within 5 mm of VDD, and unused pins must be configured as outputs or pulled to defined levels. The ICSP pins (PGD/PGC) share function with general-purpose I/O and require careful routing if in-circuit programming is needed.

見積もりお問い合わせ

PIC12F1572-E/P

PIC12F1572-E/P - 8-bit MCU, 32MHz, 3.5KB Flash, 8-PDIP | Microchip

The Microchip Technology PIC12F1572-E/P is an 8-bit enhanced mid-range PIC microcontroller with 3.5KB Flash program memory and 256 bytes RAM, packaged in an 8-pin PDIP (E/P) through-hole package. It runs up to 32MHz, delivers three independent 16-bit PWMs, integrates a 10-bit ADC with 4 channels, a 5-bit DAC, and a comparator, all in a single compact IC. According to the manufacturer datasheet (DS40001723D), the device combines 16-bit PWM, analog, and Core Independent Peripherals (CIPs) to support LED lighting, stepper motor drive, and general-purpose embedded applications. An 8-bit PIC microcontroller is a RISC-based CMOS processor optimized for low-cost, low-power embedded control. Within the PIC family hierarchy, PIC12 sits between the baseline PIC10 and the higher-pin-count PIC16/PIC18 families; PIC12F devices are 8-pin Flash variants aimed at space-constrained designs. The F1572 specifically extends PIC12 capability with three hardware 16-bit PWM channels, eliminating CPU overhead for high-resolution waveform generation. As a flash-based MCU, the program memory is in-circuit re-programmable, reducing development cost compared to older OTP PICs. Key features include 32MHz internal oscillator (8MHz with 4x PLL), 16-bit PWM with independent timers, a 10-bit ADC with 4 channels, a 5-bit DAC, one comparator, an Enhanced Universal Synchronous Asynchronous Receiver Transmitter (EUSART), and an 8-bit timer. The device operates from 1.8V to 5.5V with -40C to +125C extended temperature range, and supports low-power sleep modes ideal for battery-powered designs. The PIC12F1572-E/P uses Microchip's enhanced mid-range 8-bit core with 49 instructions and 200ns instruction cycle at 20MHz (62.5ns at 32MHz). Its Core Independent Peripherals (CIPs) such as the Configurable Logic Cell (CLC) and Complementary Waveform Generator (CWG) operate without CPU intervention, freeing the core for application logic. The CWG in particular simplifies dead-band control for half-bridge FET drivers in switching regulators and motor drives. Typical applications include LED lighting and color-mixing controllers (driven by the 16-bit PWMs and CWG), stepper motor controllers (using PWM + comparator feedback), compact DC-DC converters, and battery-powered sensor interfaces. The integrated comparator and 5-bit DAC allow closed-loop current or voltage control without external analog components. Industrial and consumer products with tight BOM cost targets are the most common fit. When designing with this device, mind that the E/P suffix denotes the -40C to +125C extended temperature grade in PDIP package. Programming is via ICSP on pins GP0/GP1; ensure those traces are accessible to the programmer header or test pads. For low-power designs, verify sleep-mode wakeup sources against your duty-cycle requirements. This page synthesizes verified distributor pricing, drop-in alternative cross-references, and practical design notes not collected in any single manufacturer PDF.

見積もりお問い合わせ

PIC12F1572-E/SN

PIC12F1572-E/SN - 8-bit MCU, 32MHz, 3.5KB Flash, 16-bit PWM | Microchip

The Microchip Technology PIC12F1572-E/SN is an 8-bit PIC microcontroller with a 32MHz internal oscillator, 3.5KB (2K x 14) Flash program memory, 256 bytes RAM, and 128 bytes EEPROM, housed in an 8-pin SOIC (SN) package. It delivers up to 32MHz MIPS performance from an enhanced mid-range 8-bit core and combines 16-bit PWM peripherals with 10-bit ADC and a comparator on-chip. An 8-bit microcontroller (MCU) is a single-chip computer built around an 8-bit data path, used for embedded control tasks where simple deterministic logic, low cost, and low power outweigh raw computation. MCUs belong to the broader category of microcontrollers within integrated circuits, sitting alongside memory ICs and interface ICs in the semiconductor hierarchy. The PIC12F1572 occupies the small-package / low-pin-count end of this family, optimized for compact analog and lighting designs. Key features include three independent 16-bit PWM channels with dedicated timers for high-resolution control, six 10-bit ADC channels, one comparator, four 8-bit DAC references, and four I/O pins. The device supports 1.8V to 5.5V operation across -40C to +125C and includes an internal 32MHz oscillator configurable to multiple frequencies. Core-independent peripherals let the CPU sleep while PWM, ADC, and comparator continue running, reducing total system power. The architecture uses Microchip's enhanced mid-range 8-bit RISC core with 49 instructions and a 200ns instruction cycle at 20MHz, pipelined to deliver 32MHz (16 MIPS) throughput. The 16-bit PWM peripheral is generated from a separate timer base, providing edge-aligned and center-aligned modes with up to 16-bit resolution. This decoupling from the CPU allows precise motor and lighting control without software overhead. Typical applications include LED lighting drivers, stepper motor control, DC-DC converter control loops, battery chargers, and general-purpose analog signal conditioning. The 16-bit PWM with 10-bit ADC feedback is well-matched to closed-loop current regulation for LED drivers and small motor control. The wide 1.8V-5.5V supply range supports both lithium-ion and 5V regulated systems. When designing with this MCU, ensure that the ICSP programming pins (ICSPCLK/ICSPDAT) are accessible on the PCB for in-circuit programming and that the MCLR pull-up is correctly configured. Use MPLAB X IDE with the MPLAB XC8 C compiler, and a PICkit 4, ICD 4, or Snap programmer for development. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

見積もりお問い合わせ

PIC12F1572-I/MF

PIC12F1572-I/MF - 8-bit 32MHz MCU, 3.5KB Flash, 8-DFN | Microchip

The Microchip Technology PIC12F1572-I/MF is an 8-bit PIC microcontroller featuring a 32MHz CPU, 3.5KB (2K x 14) Flash program memory and 256 bytes of RAM, housed in a compact 8-pin DFN (3x3 mm) package. The device operates from 2.5V to 5.5V across the industrial -40C to +85C temperature range and integrates three independent 16-bit PWMs, a 10-bit ADC, a 5-bit DAC, two comparators and the Configurable Logic Cell (CLC) peripheral family. What is an 8-bit PIC microcontroller? An 8-bit PIC microcontroller is a RISC-based CMOS embedded controller that uses a Harvard architecture to execute instructions in a single cycle. PIC microcontrollers belong to the broader category of microcontrollers -> embedded controllers -> semiconductor ICs, and are widely used in cost- and power-sensitive designs where deterministic timing and small footprints matter. The PIC12F1572 specifically targets applications needing high-resolution PWM generation in an 8-pin footprint. Key features of the PIC12F1572 include three independent 16-bit PWMs with dedicated timers for high-resolution outputs (LED dimming, motor control), a 10-bit ADC with up to 6 channels, a 5-bit DAC for analog bias generation, two comparators, and CLC (Configurable Logic Cell) that allows on-chip combinational/sequential logic without external glue chips. The 8-pin DFN (3x3 mm) package makes it suitable for space-constrained PCB designs. Technically, the PIC12F1572 is built on Microchip's enhanced mid-range 8-bit core, delivering 32MHz operation (200ns instruction cycle) with 49 instructions and 16 hardware registers. The internal oscillator can be factory calibrated to +/-1% across 2.5V-5.5V and 0C-70C, simplifying designs by removing external crystals. Core Independent Peripherals (CIPs - PWMs, comparators, CLC) operate without CPU intervention, lowering software complexity and active power. Typical applications include LED lighting and color-mixing controllers (using the three 16-bit PWMs), stepper motor and DC motor drivers, digital power supplies (SMPS), battery chargers, fan speed controllers, and small appliance control boards. The combination of small footprint and high-resolution PWM uniquely suits solid-state lighting designs. When designing with this device, note the I (Industrial) temperature grade of -40C to +85C and confirm the 8-DFN package has adequate PCB thermal land and proper reflow profile per Microchip Application Note AN233. Use the MPLAB X IDE with XC8 compiler for code development; the PICkit or Snap programmer supports in-circuit debugging.

見積もりお問い合わせ

PIC12F1572-I/MS

PIC12F1572-I/MS - 8-bit MCU, 32MHz, 3.5KB Flash, 16-bit PWM | Microchip

The Microchip Technology PIC12F1572-I/MS is an 8-bit PIC microcontroller featuring three independent 16-bit PWMs, 3.5KB (2K x 14) of Flash program memory, and 256 bytes of RAM, housed in an 8-pin MSOP package. Operating from 1.8V to 5.5V at speeds up to 32MHz (125 ns instruction cycle), the part integrates core independent peripherals that include a 10-bit ADC, 5-bit DAC, two comparators, three 16-bit PWMs, a Complementary Waveform Generator (CWG), and a Configurable Logic Cell (CLC), enabling complex signal generation without external analog or timing ICs. An 8-bit microcontroller (MCU) is a single-chip computer that executes instructions from on-chip program memory through an 8-bit data path. The PIC12F1572 belongs to the PIC12F family (8-pin mid-range core), within the broader PIC® mid-range architecture, which itself falls under the 8-bit microcontroller category. As a CMOS flash-based MCU it sits in the semiconductor product hierarchy: microcontroller -> 8-bit MCU -> embedded controller -> integrated circuit. Key features include three 16-bit PWMs with independent timers, hardware CWG for complementary drive (useful for H-bridge and half-bridge switching), on-chip 5-bit DAC, an EUSART module for asynchronous serial communication, and nanoWatt XLP low-power technology with < 50 nA typical sleep current. The 10-bit ADC provides up to 4 input channels through an external MUX. The PIC12F1572 employs a Harvard RISC architecture with 49 instructions and a 14-bit instruction word; the Flash program memory supports self-programming via ICSP, allowing in-field firmware updates. The CWG and 16-bit PWMs are designed for high-resolution applications such as LED dimming, power-converter control, and stepper-motor drive waveforms where precise timing is critical. Typical applications include multi-channel LED lighting control, brushed DC motor and stepper motor drive, switch-mode power supply digital control loops, RGB color mixing, fan speed control, and consumer remote/HID devices. Compact 8-pin designs benefit when board area is constrained but PWM resolution and analog integration are still required. When designing with this MCU, ensure decoupling capacitors (100 nF and 10 uF) are placed within 4 mm of the VDD pin and that the ICSP programming pins (ICSPCLK/ICSPDAT) are reserved or routed to test pads. The internal 16 MHz HFINTOSC accuracy is approximately +/-2 percent over voltage and temperature, so applications requiring tight UART baud rates should use a crystal or the PLL multiplier. This page synthesizes distributor stock, parametric drop-in alternatives, and practical design notes drawn from the Microchip PIC12(L)F1571/2 datasheet to support sourcing, replacement and PCB-level decisions that the manufacturer datasheet alone does not cover.

見積もりお問い合わせ

PIC12F1572-I/P

PIC12F1572-I/P - 8-bit 32MHz 3.5KB Flash MCU 8-PDIP | Microchip

The Microchip Technology PIC12F1572-I/P is an 8-bit PIC microcontroller with an enhanced mid-range core, 32 MHz operation, 3.5 KB Flash program memory, 256 bytes RAM, and 128 bytes EEPROM, housed in an 8-pin PDIP through-hole package. It integrates three independent 16-bit PWMs, a 10-bit ADC with up to 4 channels, one 5-bit DAC, two comparators, a complementary waveform generator (CWG), and an 8-bit timer. The part is specified across 2.5V, 3.3V, and 5V rails at industrial temperature range -40C to +85C. A PIC12F-series microcontroller is an 8-bit reduced instruction set (RISC) device built around a Harvard architecture, used as a low-cost system-on-chip for embedded control. PIC12F devices sit at the low end of Microchip's PIC portfolio (PIC10F -> PIC12F -> PIC16F -> PIC18F) and target small pin-count applications that still need on-chip analog and PWM peripherals. They are widely used in consumer, industrial, and IoT products where 8 pins, a handful of analog inputs, and precise timing are sufficient. Key features that distinguish the PIC12F1572 include three 16-bit PWM channels with independent time bases, enabling high-resolution control of LED drivers, stepper motors, and switch-mode power supplies. The device also includes a complementary waveform generator for half-bridge and full-bridge drive without external logic, an on-chip temperature indicator, and eXtreme Low Power (XLP) sleep modes. According to the Microchip datasheet, the enhanced mid-range core delivers up to 49 instructions per cycle in select instructions versus 24 on baseline PIC cores, improving determinism for time-critical loops. Typical applications include high-resolution LED lighting, fan and pump speed control, battery chargers, small digital power conversion, sensor conditioning, and low-cost general-purpose control boards. The combination of three 16-bit PWMs, dual comparators, and a 10-bit ADC allows the PIC12F1572 to perform closed-loop control in a single chip. When designing with the PIC12F1572-I/P, choose the PDIP package for breadboarding, hand-soldered prototypes, and educational kits. For production, consider its surface-mount siblings (PIC12F1572-I/SN SOIC-8, PIC12F1572-I/MS MSOP-8) which share the same pinout and die. Always provide a 0.1uF decoupling capacitor on VDD and follow the datasheet's In-Circuit Serial Programming (ICSP) layout recommendations. This page synthesizes distributor pricing, drop-in alternative listings, and design notes not found in the manufacturer datasheet, giving engineers a faster path to part selection and PCB reuse.

見積もりお問い合わせ

PIC12F1572-I/RF

PIC12F1572-I/RF - 8-bit MCU, 32MHz, 3.5KB Flash, 16-bit PWM | Microchip

The Microchip PIC12F1572-I/RF is an 8-bit PIC12 family RISC microcontroller running at up to 32MHz with 3.5KB (2K x 14 words) of Flash program memory and 256 bytes of RAM, housed in an 8-pin UDFN (3x3 mm) package. It integrates three independent 16-bit PWM channels, six timers, a 10-bit ADC, a 5-bit DAC, two comparators, a complementary waveform generator (CWG), and the standard PIC12 core independent peripherals including BOR, POR and WDT. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, non-volatile program memory, working RAM, and peripheral subsystems into one IC. MCUs sit one level below microprocessors in the embedded hierarchy and are categorized by bus width (8-bit, 16-bit, 32-bit), Flash size, and integrated peripheral set. PIC12F-series parts target low-pin-count (8-pin) applications where PCB area, BOM count, and power budget are critical, making them a sweet spot for compact analog-and-control designs. Key differentiating features of the PIC12F1572-I/RF include the three 16-bit PWMs with independent time bases (uncommon in an 8-pin device), 4-channel 10-bit ADC with hardware capacitive voltage divider (CVD) support, complementary waveform generator for half-bridge / full-bridge / push-pull drive, and on-board 5-bit DAC usable as a programmable reference. The instruction set is enhanced mid-range with 200 ns instruction execution at 20 MHz oscillator. Typical applications include high-resolution LED dimming and color mixing, stepper motor microstepping control, switched-mode power supply control loops, sensor signal conditioning, low-cost fan/lighting control, and battery-powered portable instrumentation. The 8-pin UDFN footprint also makes it a strong fit for space-constrained wearables and IoT edge nodes. When designing with this device, note the UDFN package has an exposed thermal pad that must be soldered to the PCB ground pour for mechanical reliability. Decouple VDD with a 100 nF ceramic capacitor placed within 3 mm of the pin, and reserve an unused GPIO for in-system debug via the ICSP/ICD pins to retain code-development flexibility. This page synthesizes distributor pricing, drop-in PIC12 alternatives, and practical design notes not found in the manufacturer datasheet alone.

見積もりお問い合わせ

PIC12F1572-I/SN

PIC12F1572-I/SN - 8-Bit MCU, 32MHz, 3.5KB Flash | Microchip

The Microchip Technology PIC12F1572-I/SN is an 8-bit enhanced mid-range PIC microcontroller with 3.5KB (2K x 14) of Flash program memory, 256 bytes of RAM, and 32MHz internal oscillator speed, housed in an 8-pin SOIC (SN, 3.9mm body) package. It integrates three independent 16-bit PWMs, a 10-bit ADC with four channels, a 5-bit DAC, two comparators, a Complementary Waveform Generator (CWG), and an EUSART — all on a single 8-pin footprint. The industrial-grade -I temperature range supports -40C to +85C operation. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (Flash), data memory (RAM), and peripherals such as ADCs, timers, and communication interfaces. Within the broader embedded hierarchy, an 8-bit MCU belongs to the microcontroller category, which sits under microcontrollers and processors in the semiconductor taxonomy. The PIC12 family represents Microchip's compact, low-pin-count MCU line designed for cost-sensitive and space-constrained designs where minimal external components and small package size matter more than raw compute throughput. Key features that differentiate the PIC12F1572 include its three 16-bit PWMs with independent timers — uncommon in 8-pin MCUs — enabling precision control applications such as LED lighting fade/dimming, motor speed control, and switched-mode power supplies. The integrated CWG complements the PWMs by providing complementary outputs with programmable dead-band delay, ideal for driving half-bridges or full-bridges in motor drive and lighting applications. Combined with the 10-bit ADC and 5-bit DAC, the part can implement closed-loop analog control without external signal conditioning ICs. Architecturally, the PIC12F1572 uses Microchip's enhanced mid-range 8-bit RISC core, which executes most instructions in a single cycle (200ns at 20MHz, 125ns at 32MHz). The Harvard architecture separates program and data buses, and the C-compiler-optimized instruction set enables efficient code generation. The on-chip 32MHz high-precision internal oscillator eliminates the need for an external crystal in most designs, further reducing BOM cost and PCB area. Typical applications include LED lighting dimming and color-mixing drivers, small DC motor and stepper control, switched-mode power supply control loops, general-purpose timer/PWM replacement of discrete logic, and battery-powered IoT edge sensors requiring analog sensing plus PWM actuation. The 8-pin SOIC package suits hand-solderable prototyping and standard SMT assembly lines. When designing with this part, ensure the ICSP programming pins (ICSPCLK/ICSPDAT) are accessible on the PCB for in-circuit programming and debugging, and add a 0.1uF decoupling capacitor close to VDD. The 16-bit PWM resolution is preserved only when the system clock is fast enough — at low FOSC values, the effective PWM resolution decreases because each PWM step requires a clock cycle. This page synthesizes distributor pricing, drop-in alternatives drawn from the same Microchip PIC12F157x family, and practical design notes not consolidated in the manufacturer datasheet alone.

見積もりお問い合わせ

PIC12F1572T-I/MF

PIC12F1572T-I/MF - 8-bit MCU 32MHz 3.5KB Flash 8-DFN | Microchip

The Microchip Technology PIC12F1572T-I/MF is an 8-bit PIC microcontroller with a 32 MHz internal oscillator, 3.5 KB (2K x 14) of Flash program memory, 256 bytes of RAM, and a 5-bit DAC, packaged in an 8-pin DFN (3x3 mm) with exposed thermal pad for tape-and-reel shipping. A microcontroller (MCU) is a single-chip computer containing a CPU core, non-volatile program memory (typically Flash), working RAM, and a set of on-chip peripherals such as timers, ADC, comparators, PWM modules, and communication interfaces. The PIC12F1572 belongs to Microchip's PIC12 mid-range core family, which sits within the broader hierarchy 8-bit PIC -> mid-range core -> RISC MCU -> microcontroller -> semiconductor. The device is built on a CMOS process and integrates three independent 16-bit PWM channels with complementary waveform generation, which is uncommon in an 8-pin package. Key features include three 16-bit PWMs with independent timers, a 5-bit DAC, comparators, ADC, and Core Independent Peripherals (CIPs) that offload timing-critical logic from the CPU. The wide 2.5 V to 5.5 V supply range supports both 3.3 V and 5 V rails. The 8-DFN package gives a compact 3x3 mm footprint suitable for high-density designs and offers better thermal performance than equivalent leaded 8-pin parts. Architecturally, the device combines the standard PIC mid-range 14-bit instruction set with configurable logic cells and PWM steering to drive half-bridges and full-bridges for LED lighting, motor control, and switched-mode power supply applications. The high-resolution 16-bit PWMs are particularly useful where analog filter sizing or audible PWM noise is a concern. Typical applications include LED lighting color mixing and dimming, stepper motor and brushed DC motor control, digital power conversion, IoT edge nodes, and consumer electronics. The high PWM resolution also suits haptic drivers and Class-D audio amplifiers where PWM noise floor must be minimized. When designing with this MCU, ensure the 8-DFN exposed pad is soldered to a sufficient copper pour for thermal dissipation and ground return. Program and debug via the in-circuit serial programming (ICSP) interface with the PICkit or MPLAB Snap programmer. This page synthesizes distributor pricing, pin-compatible drop-in alternatives, and practical design notes that complement the manufacturer datasheet and gives engineers a single decision-ready reference.

見積もりお問い合わせ

PIC12F1572T-I/RF

PIC12F1572T-I/RF - 8-Bit MCU, 32MHz, 3.5KB Flash, 8-UDFN | Microchip

The Microchip PIC12F1572T-I/RF is an 8-bit PIC microcontroller featuring a 32 MHz internal oscillator, 3.5 KB (2K x 14) of Flash program memory, 256 bytes of RAM, and an integrated 10-bit ADC with up to 4 channels, all housed in an 8-pin UDFN (3x3 mm) exposed-pad package with tape-and-reel packaging. It belongs to the PIC12(L)F157x family, which uniquely integrates three 16-bit PWM modules with independent timers alongside 5-bit and 10-bit DACs, making it purpose-built for cost-sensitive mixed-signal designs. An 8-bit PIC microcontroller (MCU) is a compact, low-power computing core built around Microchip's enhanced mid-range RISC architecture. The 8-bit MCU sits within the broader taxonomy of microcontrollers -> microcomputers -> embedded processors -> semiconductors, and is typically used for dedicated control tasks where low cost, deterministic timing, and minimal external component count are critical. The PIC12F1572 family targets general-purpose applications that previously required larger 14- or 20-pin MCUs but can now be implemented in an 8-pin footprint. Key differentiating specifications include three independent 16-bit PWMs (vs. the typical 8- or 10-bit PWM found in competing 8-pin MCUs), a 5-bit DAC and a 10-bit DAC on dedicated output pins, a complementary waveform generator (CWG), four 10-bit ADC channels, and two comparators. Operating voltage spans 2.3V to 5.5V across the -40C to +85C industrial range, with the 'F' (Flash) variant supporting in-circuit serial programming (ICSP) for field-upgradeable firmware. Architecturally, the device uses a Harvard RISC core with a single-cycle 49-instruction set, 14-bit instruction word, and hardware stack. The three 16-bit PWM channels share independent Timer2/4/6 sources and support edge- and center-aligned modes with dead-band control, enabling direct generation of high-resolution lighting, motor-control, and switch-mode power-supply waveforms without CPU intervention. Typical applications include LED lighting drivers (RGB, RGBA, and white-tuning), stepper motor control, isolated and non-isolated switch-mode power supplies, fan controls, battery chargers, and compact IoT sensor nodes. The combination of high-resolution PWM and integrated analog peripherals eliminates the need for external driver ICs in many cost-sensitive designs. When designing with the PIC12F1572T-I/RF, ensure the exposed pad (EP) on the UDFN package is soldered to a sufficient copper thermal/ground pour on the PCB - this is the device's primary ground connection. Programming requires a 5V-tolerant ICSP connection on ICSPCLK/ICSPDAT pins, and unused GPIO should be configured as outputs low to minimize quiescent current draw. This page synthesizes verified distributor pricing, drop-in alternatives, and application-specific design guidance not found in the standalone manufacturer datasheet, giving procurement and engineering teams a single source for parametric, supply-chain, and design data on PIC12F1572T-I/RF.

見積もりお問い合わせ

PIC12F1612-E/MF

PIC12F1612-E/MF - 8-bit MCU, 3.5KB Flash, 32MHz, 8-DFN | Microchip

The Microchip Technology PIC12F1612-E/MF is an 8-bit PIC microcontroller from the PIC12F family featuring a RISC architecture, 3.5KB of program Flash memory, and an 8-pin VDFN (DFN) exposed-pad package. The device runs at up to 32MHz clock speed with a wide operating voltage range of 2.5V to 5.5V, and integrates a 10-bit ADC, capture/compare/PWM (CCP), 24-bit Signal Measurement Timer (SMT), and zero-cross detect peripherals for embedded motor and general-purpose control applications. An 8-bit microcontroller (MCU) is a small, low-power computing device built around an 8-bit data path and integrated Flash program memory, peripherals, and a CPU core on a single die. The PIC12F1612 belongs to the PIC12F family, which sits within the broader PIC microcontroller hierarchy: 8-bit MCU -> PIC microcontroller -> Microchip MCU portfolio -> embedded computing devices. Low-pin-count PIC12F parts are designed for cost- and space-sensitive designs that still need hardware timers, ADC, and PWM. Key differentiating features of the PIC12F1612 include its on-chip 24-bit Signal Measurement Timer (rare in 8-pin MCUs), zero-cross detection logic for AC-line dimming, complementary waveform generator (CWG), numerically controlled oscillator (NCO), and configurable logic cell (CLC). These peripherals enable motor control, lighting, and signal conditioning without external components. The internal oscillator reduces BOM cost, and the wide 2.5V to 5.5V supply range supports both 3.3V and 5V system rails. The PIC12F1612 uses a Harvard-architecture RISC core with a single-cycle instruction set, enabling deterministic instruction timing. Its analog front-end pairs a 10-bit ADC with comparators and a fixed-voltage reference, while digital peripherals (CCP, CWG, NCO, CLC) provide flexible waveform synthesis. Code protection, low-voltage programming, and In-Circuit Serial Programming (ICSP) support simplify prototyping and field updates. Typical applications include low-end motor control (small DC and brushed motors), AC-line dimming with zero-cross detection, LED lighting and color mixing, sensor signal conditioning, and general-purpose embedded control in white goods, fans, and small appliances. The wide temperature range (-40C to +125C) and small footprint also suit automotive body and industrial sensor nodes. When designing with this part, route the exposed pad (EP) to a solid ground plane for thermal dissipation and electrical reference, and follow Microchip's DFN PCB layout guidelines for the 8-VDFN package. Programming via ICSP requires the standard PGD/PGC pin pair. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes that complement the manufacturer datasheet.

見積もりお問い合わせ

PIC12F1612-E/SN

PIC12F1612-E/SN - 8-bit 32MHz MCU, 3.5KB Flash | Microchip

The Microchip Technology PIC12F1612-E/SN is an 8-bit PIC RISC microcontroller with 32MHz internal oscillator, 3.5KB (2K x 14) Flash program memory, 256 bytes RAM, and 256 bytes data EEPROM in an 8-pin SOIC package. It operates from 2.5V to 5.5V and integrates 6 I/O pins, 6 timers, a 1-channel 8-bit DAC, and a 4-channel 10-bit ADC. The -E suffix denotes the extended industrial temperature grade of -40C to +125C, while /SN indicates the 8-pin SOIC (150-mil narrow-body) package. What is an 8-bit microcontroller? An 8-bit microcontroller is a small, self-contained computing core on a single IC that fetches, decodes, and executes 8-bit-wide instructions from on-chip Flash memory. PIC12-series parts belong to Microchip's baseline-and-mid-range 8-bit family, positioned hierarchically below PIC16 (mid-range) and PIC18 (enhanced) parts in the broader PIC taxonomy of microcontrollers -> embedded controllers -> semiconductor ICs. The PIC12F1612's distinctive value is on-chip motor-control peripherals such as 24-bit Signal Measurement Timer (SMT), Zero-Cross Detect (ZCD), and Complementary Waveform Generator (CWG), which are uncommon in this pin-count class. Key features include 3.5KB self-programmable Flash with 10,000 erase/write cycles, 256 bytes RAM, 256 bytes EEPROM, a 10-bit ADC with 4 channels and up to 100 ksps conversion rate, an 8-bit DAC, multiple timer modules including the 24-bit SMT for precise time measurement, and Capture/Compare/PWM (CCP) peripherals. The integrated Zero-Cross Detect simplifies AC-line sensing without external optocouplers, and the CWG generates complementary PWM waveforms for driving MOSFET half-bridges in low-power motor control. The PIC12F1612 uses Microchip's enhanced mid-range 8-bit CPU core with a 14-bit instruction word, single-cycle execution except for branches, and a hardware stack for fast context switching. The internal 32MHz oscillator is factory calibrated to +/-1% and supports a wide operating voltage range for both battery and 5V rail applications, while the integrated 4-channel 10-bit ADC enables direct sensor interfacing without external signal conditioning. Typical applications include small DC motor control in fans and pumps, AC-line dimming and zero-cross switching, LED lighting control with PWM and CWG outputs, battery-powered IoT sensor nodes, and general-purpose embedded control in appliances and consumer products. The combination of SMT, ZCD, and CWG peripherals in an 8-pin footprint is rare in the marketplace and is the primary reason engineers select this part over generic PIC12F alternatives. When designing with this device, take care to bypass VDD with a 100nF ceramic capacitor placed within 5mm of the pin, and ensure MCLR is pulled high through a 10k resistor for normal operation. The internal oscillator eliminates external crystals for most uses but may not suit USB or precise-timing applications, where a PIC16F or PIC18F part with an external oscillator is preferred. This page synthesizes distributor pricing, drop-in compatible alternatives from Microchip's PIC12 family, and practical design notes not aggregated on a single manufacturer or distributor page.

見積もりお問い合わせ

PIC12F1612-I/MF

PIC12F1612-I/MF - 8-bit MCU, 32MHz, 3.5KB Flash, 8-DFN | Microchip

The Microchip Technology PIC12F1612-I/MF is an 8-bit PIC microcontroller running up to 32 MHz, equipped with 3.5 KB (2K x 14) of Flash program memory, 256 bytes of SRAM, and 256 bytes of EEPROM, housed in an 8-pin DFN (3x3 mm) package. The device integrates core-independent peripherals such as a 10-bit ADC with Computation (ADCC), a 24-bit Signal Measurement Timer (SMT), Complementary Waveform Generator (CWG), Numerically Controlled Oscillator (NCO), and Configurable Logic Cells (CLC), enabling complex control tasks without CPU intervention. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, non-volatile program memory (typically Flash), working RAM, and a rich set of on-chip peripherals such as timers, ADC, communication interfaces, and I/O pins. The PIC12F1612 belongs to the PIC® 12F family of 8-bit microcontrollers, positioned in Microchip's mid-range PIC portfolio as an 8-pin compact MCU for embedded control of small motors, LED lighting, sensor signal conditioning, and general-purpose applications. Its position in the broader taxonomy is: PIC12F1612 -> PIC12F family -> 8-bit PIC MCU -> Microcontroller -> Semiconductor. Key features of the PIC12F1612 include six I/O pins sharing six peripheral functions, two 8-bit timers plus one 16-bit timer, a 10-bit ADC with oversampling and averaging, hardware limit timer, and zero-cross detection. The device operates from 2.5 V to 5.5 V and supports industrial temperature range of -40 °C to +85 °C. An internal 32 MHz oscillator with ±1 % accuracy eliminates the need for an external crystal in most designs, reducing BOM cost and PCB area. The architecture is built on Microchip's enhanced mid-range 8-bit core using a 14-bit instruction set, providing single-cycle operation for most instructions at 32 MHz (125 ns instruction cycle). On-chip peripherals like CWG and NCO offload waveform synthesis and frequency generation from the CPU, enabling deterministic hardware-driven control loops useful for motor drive, dimming, and pulse generation. The wide peripheral set allows a single MCU to replace multiple analog/discrete components. Typical applications include small DC motor and fan control, LED lighting dimming and color mixing, capacitive-touch user interfaces, sensor signal conditioning with hardware averaging, and compact consumer appliances. The 8-DFN 3x3 mm footprint makes it well-suited for space-constrained designs. When designing with the PIC12F1612, ensure proper decoupling (100 nF + 1 µF) close to VDD, and verify that the total I/O sink/source current budget (per-pin and per-port) is respected for LED or relay drive scenarios. Always check the latest PIC12F1612 errata document for known device issues during firmware development. This page synthesizes distributor pricing, drop-in alternative MCUs, and practical design notes not found in the manufacturer datasheet alone, helping engineers evaluate the PIC12F1612-I/MF against its PIC12F1571, PIC12F1572, and PIC12F1501 siblings, as well as automotive-grade -Q variants.

見積もりお問い合わせ

PIC12F1612-I/P

PIC12F1612-I/P - 8-Bit MCU, 3.5KB Flash, 32MHz | Microchip

The Microchip Technology PIC12F1612-I/P is an 8-bit PIC microcontroller with 3.5KB Flash, 256 bytes RAM, and a 32MHz internal oscillator, housed in an 8-pin PDIP through-hole package. It operates from 2.5V to 5.5V and integrates peripherals including a 10-bit ADC, CCP, 24-bit SMT (Signal Measurement Timer), Zero-Cross Detection, and a complementary waveform generator. A PIC microcontroller is a compact, RISC-based 8-bit microprocessor with on-chip Flash, RAM, and peripherals, designed for embedded control tasks. PIC12F16xx devices sit at the low end of the PIC12 family hierarchy, which is part of the broader Microchip 8-bit MCU portfolio spanning PIC10, PIC12, PIC16, and PIC18 families. These tiny MCUs are optimized for cost-sensitive, low-pin-count applications where a full 28- or 40-pin device is overkill. Key features of the PIC12F1612 include 3.5KB (2K x 14) self-programmable Flash program memory, 256 bytes of RAM, 6 I/O pins, an enhanced mid-range 14-bit instruction set, and a 32MHz internal oscillator that eliminates the need for an external crystal. Additional capabilities include a 10-bit ADC with up to 8 channels, 2 PWM modules, I2C and SPI, and a 24-bit SMT for precision timing. The device uses Microchip's enhanced mid-range core with a 14-bit instruction word, supporting interrupts, hardware stack, and 49 instructions. The internal 32MHz oscillator delivers 8 MIPS performance, suitable for motor control loops, LED dimming, and simple state machines without an external clock component. Typical applications include small motor control (BLDC, stepper), general-purpose embedded control, IoT edge nodes, fan control, LED lighting, and consumer appliances. The Zero-Cross Detection and 24-bit SMT make it well-suited for AC line-voltage control and energy metering. When designing with this MCU, allocate at least 1.5KB of Flash for bootloader and application code, use the internal 32MHz oscillator to minimize BOM, and place a 0.1uF decoupling capacitor as close as possible to VDD. The -I/P industrial temperature grade supports -40C to +85C operation. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet, providing engineers with a single decision-ready reference for selecting and sourcing the PIC12F1612-I/P.

見積もりお問い合わせ

PIC12F1612T-I/MF

PIC12F1612T-I/MF - 8-bit MCU, 3.5KB Flash, 32MHz | Microchip

The Microchip Technology PIC12F1612T-I/MF is an 8-bit PIC microcontroller featuring 3.5KB Flash program memory, 256 bytes of RAM, and a 32 MHz internal oscillator, housed in an 8-pin VDFN (Dual Flat No-lead) exposed-pad package. The "T" suffix denotes tape-and-reel packaging, "I" indicates the industrial temperature grade (-40C to +85C), and "MF" specifies the 8-pin VDFN package with an exposed thermal pad. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (Flash), working memory (RAM), and programmable I/O peripherals. The PIC12 family belongs to Microchip's 8-bit mid-range core architecture, sitting within the broader taxonomy of embedded microcontrollers -> microcontrollers -> microprocessors -> semiconductors. The PIC12F1612 specifically targets low pin-count applications where compact size, integrated peripherals, and low power are critical. Key differentiating features include on-chip 10-bit Analog-to-Digital Conversion (ADC), Capture/Compare/PWM (CCP) modules, 24-bit Signal Measurement Timer (SMT), Zero-Cross Detection, and Math Accelerator peripherals. These integrated features reduce external component count and BOM cost while supporting applications such as small motor control, LED driving, and sensor signal conditioning. The device operates from 2.3V to 5.5V across the industrial temperature range, providing flexibility for both 3.3V and 5V system designs. The internal 32 MHz oscillator eliminates the need for an external crystal in cost-sensitive designs, and the exposed thermal pad enhances power dissipation for applications running at higher clock rates or in thermally constrained enclosures. Typical applications include small DC motor control (fans, blowers, valve actuators), LED lighting control, sensor interface boards, low-cost consumer appliances, and general-purpose embedded control. The combination of compact 8-pin packaging and rich peripheral integration makes it well suited for space-constrained designs. A key design consideration is the exposed pad on the VDFN package, which must be soldered to the PCB ground plane to meet the specified thermal performance. For applications requiring more memory or peripherals, designers should evaluate the PIC12F1613 or PIC16F1614/1618 variants in larger pin-count packages. This page synthesizes distributor pricing, drop-in alternative cross-references, and practical PCB design notes for the PIC12F1612T-I/MF that are not consolidated on any single manufacturer or distributor page, providing actionable information for both design engineers and component buyers.

見積もりお問い合わせ

PIC12F1822-E/MF

PIC12F1822-E/MF - 8-Bit 32MHz XLP MCU 3.5KB Flash | Microchip

The Microchip PIC12F1822-E/MF is an 8-bit PIC microcontroller from the PIC12F family built on Microchip's enhanced mid-range core, featuring 3.5KB (2K x 14) of Flash program memory, 128 bytes of SRAM, and 256 bytes of EEPROM, packaged in an 8-pin DFN (3x3 mm) industrial-grade enclosure. It operates from 1.8V to 5.5V supply, runs at up to 32 MHz internal oscillator, and integrates nanoWatt XLP (eXtreme Low Power) technology that drops quiescent current to roughly 20 nA in sleep mode. An 8-bit microcontroller (MCU) is a small single-chip computer built around an 8-bit data path; it is the simplest member of the microcontroller hierarchy, sitting below 16-bit MCUs, 32-bit ARM Cortex-M MCUs, and microprocessors. The PIC12F1822 belongs to Microchip's 8-bit PIC microcontroller family, which uses a RISC Harvard architecture and is widely deployed in low-cost, low-power embedded control tasks. Within the broader taxonomy: PIC12F -> PIC10/12/16 family -> 8-bit MCU -> microcontroller -> embedded processor -> semiconductor. Key features include six I/O pins, an integrated 32 MHz internal oscillator with 4x PLL option, 10-bit ADC with up to 8 channels, multiple PWM and enhanced PWM modules, an EUSART, an MSSP (I2C/SPI) module, and an on-chip temperature indicator. The device offers configurable internal pull-ups, interrupt-on-change pins, and a watchdog timer for safety-critical applications. Peripherals are individually enabled via the PMD (Peripheral Module Disable) registers to minimize dynamic power consumption. The PIC12F1822 is implemented in a low-power CMOS process, with supply current scaling linearly with clock speed. The architecture supports 49 instructions, a 16-level hardware stack with overflow/underflow reset, and direct/indirect/relative addressing modes. In-circuit debugging is available via the ICSP interface using PICkit 3, MPLAB ICD 3, or the optional AC244043/AC244044 headers, removing the need for an external debug header. Typical applications include battery-powered sensor nodes, low-end remote controls, LED lighting controllers, energy-harvesting devices, household appliances, and portable medical accessories. The combination of tiny DFN-8 footprint and nanoWatt XLP sleep currents makes it especially attractive for coin-cell and energy-harvesting designs. Designers should choose this part when a sub-$1 MCU with deep-sleep current below 50 nA, 6 usable I/O lines, and a 3x3 mm PCB footprint is needed. Note that the Extended (E) temperature grade spans -40C to +125C, so for cost-sensitive commercial-only designs the -I/MF variant can be considered instead. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone. It is intended as a technical reference complementing the Microchip PIC12F1822 datasheet (DS40001413G).

見積もりお問い合わせ

PIC12F1822-E/P

PIC12F1822-E/P - 8-bit MCU, 3.5KB Flash, 32MHz, 8-PDIP | Microchip

The Microchip Technology PIC12F1822-E/P is an 8-bit RISC microcontroller from the PIC12F family featuring 3.5 KB of FLASH program memory, 128 bytes of RAM, and 256 bytes of EEPROM, housed in an 8-pin PDIP (through-hole) package. The device operates from 1.8 V to 5.5 V (per the family datasheet) and runs at up to 32 MHz internal oscillator speed, delivering 49 instructions with a 16-level hardware stack and 8-bit data path. An 8-bit microcontroller (MCU) is a single-chip computer with an 8-bit data bus, integrating a CPU, non-volatile program storage (FLASH/ROM), working memory (RAM), and peripherals. The PIC12F1822 belongs to the PIC12F sub-family -> PIC10/12/16 family -> PIC microcontrollers -> 8-bit microcontrollers -> microcontroller (MCU) -> embedded processor -> integrated circuit hierarchy. It is specifically engineered for low-pin-count, ultra-low-power applications using Microchip's nanoWatt XLP technology, which can reduce sleep current to ~20 nA. Key features include 6 bidirectional I/O pins, four 10-bit ADC channels (shared with I/O), one 5-bit DAC, two comparators, five timers, capture/compare/PWM modules, EUSART, MSSP (I2C/SPI), and integrated ICD (in-circuit debug) support. The 32 MHz internal oscillator provides 8 MIPS throughput. Brown-out Reset (BOR), Power-On Reset (POR), and Watchdog Timer (WDT) provide embedded robustness. Compared to the older PIC12F615/PIC12F508, the PIC12F1822 adds a richer peripheral set and CIP (Core Independent Peripherals). Typical applications include battery-powered sensor nodes, LED control, consumer appliance user-interface boards, and low-cost logic-replacement modules where size and power are critical. The integrated CIP peripherals (e.g., PWM, ADC, comparator) let designers replace discrete analog blocks with deterministic on-chip silicon, reducing BOM cost. When designing with this part, place a 100 nF decoupling capacitor as close to VDD as possible and respect the ICD signal-pin layout (PGC/PGD on RA0/RA1) to enable in-circuit debug via PICkit 3 or MPLAB Snap. The device supports the ICSP programming interface through the same pins. This page synthesizes verified distributor pricing, drop-in compatible alternatives (same 8-pin PDIP footprint), and practical design notes that augment the manufacturer datasheet.

見積もりお問い合わせ

PIC12F1822-I/SN

PIC12F1822-I/SN - 8-Bit XLP MCU, 3.5KB Flash, 32MHz | Microchip

The Microchip Technology PIC12F1822-I/SN is an 8-bit PIC® XLP™ microcontroller featuring a 32MHz internal oscillator, 3.5KB (2K x 14 words) of Flash program memory, 128 bytes of RAM, and 256 bytes of EEPROM, housed in an 8-pin SOIC (SN) package. It belongs to the enhanced mid-range PIC12 family and integrates six general-purpose I/O pins plus one input-only pin, making it suitable for compact, low-pin-count designs. An 8-bit microcontroller (MCU) is a single-chip computer that integrates a CPU, program memory (Flash/ROM), data memory (RAM), non-volatile storage (EEPROM), and peripheral interfaces onto one silicon die. The PIC12F1822 uses Microchip's RISC-based PIC architecture with 200 ns instruction execution, a single-cycle oscillator, and nanoWatt XLP technology. Within the product hierarchy, this places it as: 8-bit MCU -> microcontroller -> embedded processor -> semiconductor. The XLP nanoWatt feature set enables ultra-low sleep currents below 50 nA typical, which is critical for battery-powered applications. Key features include 6 I/O pins with individual direction control, an internal 32MHz oscillator (selectable from 31kHz to 32MHz via software), a 10-bit ADC with up to 8 channels, two 8-bit timers plus one 16-bit timer, enhanced PWM modules (ECCP + CCP), hardware USART, I2C, and SPI peripherals, and an integrated temperature indicator. It also supports capacitive-touch sensing via the mTouch™ peripheral and includes an on-chip debug interface. Typical applications include battery-powered sensor nodes, IoT end devices, LED lighting controllers, consumer appliance user-interface controllers, smart-home sensor hubs, and hobbyist/Maker projects using the Curiosity development board. Designers benefit from in-circuit serial programming (ICSP) for low-voltage programming and debug without a separate header. When designing with this part, ensure VDD decoupling with 100nF ceramic capacitors close to the supply pin. For ICSP, dedicate pins to ICSPCLK and ICSPDAT, and avoid placing large capacitors on those lines. The wide 1.8V-5.5V operating range allows direct Li-ion battery operation.

見積もりお問い合わせ

PIC12F1822T-E/MF

PIC12F1822T-E/MF - 8-bit MCU, 3.5KB Flash, 32MHz, DFN-8

The Microchip Technology PIC12F1822T-E/MF is an 8-bit enhanced mid-range PIC12 microcontroller built on nanoWatt XLP (eXtreme Low Power) technology, delivering 32 MHz performance from a 3.5 KB Flash program memory and 128 B SRAM in an 8-pin DFN-EP package on tape-and-reel. According to the Microchip product family brief, the PIC12F1822 family integrates a precision 32 MHz internal oscillator, 10-bit ADC with computation (ADC2), up to four PWM modules, and configurable logic cells that replace simple external glue logic. What is an 8-bit PIC microcontroller? An 8-bit PIC microcontroller is a RISC-based CMOS microcomputer from Microchip Technology that executes one instruction per cycle (typically 200 ns at 20 MHz, 125 ns at 32 MHz) and is part of the broader microcontroller > microcomputer > embedded IC hierarchy. The PIC12 sub-family targets ultra-small pin-count (8-pin and 14-pin) applications where board space, low quiescent current, and integrated peripherals matter more than raw computational throughput. Key features of the PIC12F1822T-E/MF include 3.5 KB self-programmable Flash with 256 B EEPROM, 128 B RAM, six I/O pins plus one input-only pin, and a 32 MHz internal oscillator accurate to within ±1% across voltage and temperature. Peripherals include a 10-bit ADC, two 8-bit timers and one 16-bit timer, enhanced USART, MSSP (SPI/I2C), up to four 10-bit PWM outputs with complementary and dead-band control, and configurable logic cells (CLC) that implement combinational/sequential logic in hardware. The architecture uses a 14-bit instruction word with an 8-level hardware stack, 32-byte access bank for fast SFR access, and a vectored interrupt controller with context save-on-entry. The XLP technology delivers typical sleep currents below 20 nA at 1.8 V, watchdog timer currents around 400 nA, and active currents around 50 µA/MIPS at 1 MHz / 1.8 V, making the part attractive for battery-powered and energy-harvesting designs. Typical applications include automotive sensor interfaces (the -E suffix denotes -40°C to +125°C automotive temperature grade), low-power IoT sensor nodes, LED lighting controllers, consumer appliance user interfaces, and small motor-control loops using the integrated PWM and CLC blocks. The wide 1.8 V to 5.5 V operating range allows direct connection to 2-cell battery stacks or 5 V rails without external level shifting. When designing with the PIC12F1822T-E/MF, leverage the integrated 32 MHz oscillator to avoid external crystals, reserve one I/O for ICSP programming, and place a 0.1 µF decoupling capacitor within 5 mm of the VDD pin. The DFN-EP exposed pad must be soldered to a thermal pad on the PCB for proper thermal dissipation. This page synthesizes distributor pricing, drop-in alternatives from the PIC12 family, and practical design notes not found in the manufacturer datasheet.

見積もりお問い合わせ

PIC12F1822T-I/MF

PIC12F1822T-I/MF - 8-bit 32MHz 3.5KB Flash MCU | Microchip

The Microchip PIC12F1822T-I/MF is an 8-bit PIC microcontroller from the PIC12 enhanced mid-range lineup, featuring 3.5KB (2K x 14) of Flash program memory, 128 bytes of RAM, and 256 bytes of EEPROM in a compact 8-pin DFN (3x3 mm) package. It executes instructions at 200 ns (5 MIPS at 32 MHz) while supporting a wide 1.8V to 5.5V operating voltage range and consuming as little as 20 nA in sleep mode, making it one of Microchip's nanoWatt XLP eXtreme Low-Power family members. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program and data memory, peripherals, and I/O onto one silicon die. The PIC family falls under the broader hierarchy: 8-bit microcontroller -> microcontroller -> embedded processor -> semiconductor. MCUs run firmware stored in non-volatile memory and target deterministic real-time control tasks, in contrast to microprocessors that require external memory and run operating systems. The PIC12 sub-family targets low-pin-count, cost-sensitive, battery-powered designs where smallest PCB footprint and lowest quiescent current are critical. Key features include an integrated 32 MHz internal oscillator (no external crystal required), 6 I/O pins, four 10-bit ADC channels, two PWM modules, three timers, an Enhanced Universal Synchronous Asynchronous Receiver Transmitter (EUSART), and an MSSP module supporting SPI and I2C. The on-chip debugger and ICSP programming interface eliminate external debug headers on basic designs, and a Peripheral Pin Select (PPS) remaps digital peripherals to any I/O pin. The PIC12F1822 architecture uses a 14-bit instruction word RISC core with a hardware stack and 32-level deep interrupt priority, enabling deterministic interrupt response. Internal voltage reference, comparators, and a configurable logic cell (CLC) allow analog signal conditioning without external components, while nanoWatt XLP technology provides multiple low-power modes (sleep, dozing, peripheral module disable) for energy harvesting and coin-cell applications. Typical applications include IoT sensor nodes, battery-powered remote controls, wearable health monitors, LED lighting controllers, low-end motor control (small DC fans and BLDC drivers), white goods user-interface boards, and consumer peripherals. Industrial uses include 4-20 mA loop-powered sensor transmitters, HVAC damper actuators, and small appliance control boards. When designing with this device, derate the maximum clock frequency linearly below 2.3V to 16 MHz. Place a 0.1 uF decoupling capacitor within 3 mm of VDD and a 10 uF bulk capacitor near the package. Avoid using the ICSP pins as high-current outputs because the in-circuit debugger shares those pads. This page consolidates distributor pricing, drop-in same-package alternatives, application circuits, and design notes that complement the manufacturer datasheet.

見積もりお問い合わせ

サブカテゴリ

製品 (38,000+)

PIC12F1571T-I/MF - 8-Bit MCU, 32MHz, 1.75KB Flash 8-DFN | Microchip

PIC12F1571T-I/MS - 8-Bit MCU, 32MHz, 1.75KB Flash, 3x16-bit PWM | Microchip

PIC12F1571T-I/SN - 8-bit MCU, 32MHz, 1.75KB Flash | Microchip

PIC12F1572-E/MF - 8-bit MCU, 3.5KB Flash, 3x 16-bit PWM | Microchip

PIC12F1572-E/MS - 8-bit MCU, 32MHz, 3.5KB Flash, 16-bit PWM | Microchip

PIC12F1572-E/P - 8-bit MCU, 32MHz, 3.5KB Flash, 8-PDIP | Microchip

PIC12F1572-E/SN - 8-bit MCU, 32MHz, 3.5KB Flash, 16-bit PWM | Microchip

PIC12F1572-I/MF - 8-bit 32MHz MCU, 3.5KB Flash, 8-DFN | Microchip

PIC12F1572-I/MS - 8-bit MCU, 32MHz, 3.5KB Flash, 16-bit PWM | Microchip

PIC12F1572-I/P - 8-bit 32MHz 3.5KB Flash MCU 8-PDIP | Microchip

PIC12F1572-I/RF - 8-bit MCU, 32MHz, 3.5KB Flash, 16-bit PWM | Microchip

PIC12F1572-I/SN - 8-Bit MCU, 32MHz, 3.5KB Flash | Microchip

PIC12F1572T-I/MF - 8-bit MCU 32MHz 3.5KB Flash 8-DFN | Microchip

PIC12F1572T-I/RF - 8-Bit MCU, 32MHz, 3.5KB Flash, 8-UDFN | Microchip

PIC12F1612-E/MF - 8-bit MCU, 3.5KB Flash, 32MHz, 8-DFN | Microchip

PIC12F1612-E/SN - 8-bit 32MHz MCU, 3.5KB Flash | Microchip

PIC12F1612-I/MF - 8-bit MCU, 32MHz, 3.5KB Flash, 8-DFN | Microchip

PIC12F1612-I/P - 8-Bit MCU, 3.5KB Flash, 32MHz | Microchip

PIC12F1612T-I/MF - 8-bit MCU, 3.5KB Flash, 32MHz | Microchip

PIC12F1822-E/MF - 8-Bit 32MHz XLP MCU 3.5KB Flash | Microchip

PIC12F1822-E/P - 8-bit MCU, 3.5KB Flash, 32MHz, 8-PDIP | Microchip

PIC12F1822-I/SN - 8-Bit XLP MCU, 3.5KB Flash, 32MHz | Microchip

PIC12F1822T-E/MF - 8-bit MCU, 3.5KB Flash, 32MHz, DFN-8

PIC12F1822T-I/MF - 8-bit 32MHz 3.5KB Flash MCU | Microchip