インターフェースIC
サブカテゴリ
製品 (1568)
TJA1463ATK/0Z - CAN SIC Transceiver, 8Mbit/s, Sleep | NXP
The NXP Semiconductors TJA1463ATK/0Z is a CAN Signal Improvement Capability (SIC) transceiver with Sleep mode, supporting CAN FD communication up to 8 Mbit/s and housed in a 14-pin HVSON (SOT1086-1) package. It implements the SIC behavior defined in CiA 601-4 and ISO 11898-2:2024 parameter set C, while remaining fully interoperable with classical CAN and CAN FD nodes defined by ISO 11898-2:2024 and SAE J2284-1 through J2284-5. The /0Z suffix denotes the tape-and-reel, 100% matte-tin lead-free, Pb-free, AEC-Q100-qualified automotive-grade ordering code. A CAN SIC (CAN Signal Improvement Capability) transceiver is a physical-layer device that sits between a CAN protocol controller and the differential CAN bus, translating the controller's TX/RX logic into the bus's dominant/recessive differential signaling. The "signal improvement" function actively damps the dominant-to-recessive edge ringing that traditionally limits CAN FD bus length and stub density, allowing larger topologies than classical HS-CAN. In the system hierarchy it belongs to: CAN transceiver -> network interface IC -> interface IC -> integrated circuit -> semiconductor. Key features include up to 8 Mbit/s CAN FD data rate, tight bit-timing symmetry enabling communication at 5 Mbit/s with a higher node count, an integrated low-power Sleep mode with remote wake-up via bus activity, a separate VIO supply pin for flexible MCU interfacing from 1.8V to 5V, an STB (standby) mode pin, and an ERR output pin that flags local and global bus failures. The HVSON-14 package provides a small PCB footprint with a thermal pad for improved dissipation in ECU environments. Architecturally the TJA1463ATK/0Z combines a high-speed differential bus driver/receiver pair, an internal slope-control/SIC current-shaping network, a low-drop VIO level shifter, a low-quiescent Sleep regulator with bus-wake comparator, and ESD protection rated to IEC 61000-4-2 on the bus pins. The SIC behavior is achieved without external components - just the standard CAN bus termination and a 5V or 3.3V VCC. Typical applications include automotive body controllers, ADAS sensor nodes (radar, lidar, camera ECUs), chassis and powertrain ECUs, battery management systems (BMS) and battery energy storage system (BESS) communication links, industrial CAN FD backbones, and any classical-CAN network that is being migrated to CAN FD with longer cables or more nodes than the legacy bus can support. When designing with this part, ensure VIO matches the host MCU supply, place the bus termination (typically 120 ohm at each bus end) within the recommended layout, and follow NXP's EMC and ESD layout guidance in the application notes. The Sleep pin and the VIO domain must be sequenced correctly to enter and exit Sleep cleanly. This page synthesizes distributor pricing, AEC-Q100 compliance status, drop-in pin-compatible alternatives in the TJA146x family, and practical CAN SIC design notes not consolidated in the manufacturer datasheet.
TJF1051T/3/1 - High-Speed CAN Transceiver SOIC-8 | NXP
The NXP TJF1051T/3/1 is a high-speed Controller Area Network (CAN) transceiver that serves as the physical interface between a CAN protocol controller and the differential CAN bus, supplied in an 8-pin SOIC package. It supports CAN data rates up to 1 Mbit/s (classical CAN) and the CAN FD (Flexible Data-rate) extension at higher bus speeds, with versions tailored to common microcontroller I/O voltages. The /3 suffix denotes a 5 V MCU interface variant where VIO is internally tied to VCC, so TXD/RXD logic levels are compatible with 5 V microcontrollers directly. A CAN transceiver is a physical-layer (PHY) device that converts digital logic from a microcontroller into the differential dominant/recessive signaling required by the ISO 11898 CAN bus standard. Inside the broader product taxonomy it sits beneath CAN interface ICs -> network interface ICs -> interface ICs -> integrated circuits. The TJF1051T belongs to NXP's family of third-generation high-speed CAN transceivers designed to replace the legacy TJA1051/PCA82C250/IFX1051LE predecessors while delivering enhanced electromagnetic compatibility and electrostatic discharge immunity. Key features of the TJF1051T/3/1 include improved EMC/ESD performance compared with earlier generations, ideal passive behavior on the CAN bus when supply voltage is removed (zero load with VCC = 0 V so the bus is not biased by the node), an S (Silent) pin for low-power listen-only mode, and bus-fault protection against automotive transients per ISO 7637. The differential bus pins (CANH, CANL) tolerate typical automotive battery and jump-start voltages present on 12 V systems. Internal architecture combines a high-speed differential driver/receiver pair with thermal shutdown, under-voltage detection on VCC/VIO, bus-dominant time-out protection, and an unpowered node detection that keeps the bus in recessive when the IC is off. Together these blocks implement the CAN physical layer defined in ISO 11898-2:2003, ISO 11898-5:2007 and the pending updated ISO 11898-2:2016 release, including the CAN FD frame format. Typical applications include body-control modules, powertrain networks, electric vehicle battery management (BMS) slave nodes, industrial CANopen and DeviceNet nodes, onboard chargers, and CAN-to-UART bridges for diagnostics. The /3 variant is the right choice when pairing with a 5 V microcontroller, while the non-/3 variant supports a separate VIO rail for 3.3 V MCUs. The TJF1051T/3/1 was developed as a pin-compatible, functionally equivalent upgrade for the TJA1051T/3 in existing automotive CAN networks, allowing reuse of proven PCB footprints. When designing, ensure the bus-termination topology and stub lengths follow ISO 11898-2 to maximize signal integrity at 1 Mbit/s and beyond. The Silent pin enables low-current standby and is required for partial-networking sleep modes. This page synthesizes NXP manufacturer specifications, distributor pricing tiers, cross-brand drop-in alternatives (TCAN1051, MCP2562FD, NCV7342), and practical PCB layout notes - content not compiled on the manufacturer product page alone.
TJF1051T/3/1J - High-Speed CAN Transceiver, SO-8 | NXP
The NXP TJF1051T/3/1J is a high-speed Controller Area Network (CAN) transceiver providing the physical interface between a CAN protocol controller and the differential two-wire CAN bus, packaged in an 8-pin SO (SOIC-8) surface-mount package. It supports data rates up to 5 Mbit/s and implements the CAN physical layer defined by ISO 11898-2:2003, ISO 11898-5:2007, and the pending ISO 11898-2:2016 update. A CAN transceiver is the analog front-end that converts the digital TXD/RXD logic levels of a microcontroller into the differential dominant/recessive signalling required on the CAN bus, while also providing ESD protection, bus fault tolerance, and common-mode rejection. The TJF1051T/3 family adds a VIO level-adapter supply pin that allows direct interfacing to microcontrollers with supply voltages from 3V to 5V, simplifying mixed-voltage designs where the MCU runs at 3.3V but the bus nodes may operate at 5V. Key features include an extremely low ElectroMagnetic Emission (EME) due to built-in slope control on the CANH/CANL outputs, a Silent mode (S) input for low-power bus monitoring without disturbing traffic, and high immunity to ElectroMagnetic Interference (EMI) on the bus lines. The device also includes thermal shutdown, bus dominant time-out protection, and an undervoltage detector on VCC and VIO, ensuring robust behaviour on harsh automotive or industrial bus networks. It is the pin-compatible successor to the TJA1051 with improved EMC behaviour and tighter parametric compliance with the ISO 11898-2:2016 specification. Typical applications include automotive body and chassis CAN nodes, industrial CANopen networks, building automation, and any MCU-to-CAN-bus interface requiring 3.3V or 5V logic compatibility with low EME and high EMI immunity. Compared with older TJA1050/TJA1040 designs, the TJF1051T/3 provides substantially reduced electromagnetic emissions, removing the need for external common-mode chokes in many layouts. When designing with this part, place the VIO decoupling capacitor as close as possible to pin 5 and ensure both VCC and VIO are present before TXD transitions are applied. The Silent mode pin must be tied LOW for normal operation or driven by the MCU when bus diagnostics or low-power standby states are required. The /1 JTR suffix indicates 2500-piece reel packaging.
TJF1052IT - Galvanically Isolated High-Speed CAN Transceiver | NXP
The NXP Semiconductors TJF1052IT is a galvanically isolated high-speed CAN transceiver that provides an isolated interface between a Controller Area Network (CAN) protocol controller and the physical two-wire CAN bus, delivered in a 16-pin SOIC package with 1 kV / 2.5 kVrms integrated isolation and 2 Mbps data rate support. According to NXP's product page, this part is specifically targeted at industrial applications where galvanic isolation barriers are required, eliminating the need for a separate digital isolator plus isolated DC-DC bias supply. A CAN transceiver is a physical-layer device that converts digital transmit/receive logic from a CAN controller into the differential voltage signaling required by the ISO 11898-2 CAN bus standard, and vice versa. The TJF1052IT integrates the transceiver with on-chip galvanic isolation, placing it in the hierarchy: physical-layer transceiver -> automotive/industrial bus interface -> CAN interface IC -> Interface IC. Integrated isolation removes the need for external optocouplers, isolation transformers, or digital isolator ICs, simplifying PCB layout and reducing BOM count in industrial CAN nodes. Key features include 2 Mbps CAN FD data rate support, 1 kVrms (variant /1Y) or 2500 Vrms (variant /2Y) isolation withstand voltage, 20 kV/us common-mode transient immunity (CMTI), and integrated isolated DC-DC bias supply so the bus-side node can be fully floating. Variants such as TJF1052IT/1Y, TJF1052IT/2Y, and TJF1052IT/5Y differ primarily in isolation voltage rating, with the /5Y variant qualified for functional safety contexts. The 16-SOIC wide-body (7.50 mm) package provides the clearance and creepage distances needed to meet reinforced insulation requirements. Typical applications include isolated industrial CAN nodes (PROFIBUS-style networks), PLCs, battery management systems, solar inverters, and any industrial control bus where the node must float at high common-mode voltage relative to the host. The device operates from a single 3.3 V or 5 V supply on the logic side and includes thermal shutdown, bus dominant time-out, and TXD/RXD logic pins compatible with standard CAN controllers. When designing with this part, ensure that the wide-body SOIC creepage/clearance around the package meets the end-equipment's pollution degree and over-voltage category. Designers do not need an external isolated bias supply, but should still include proper PCB edge plating and slot routing to preserve the integrated isolation rating. Use NXP's application note on isolated CAN node design for layout guidance.
TJF1052IT/1Y - Isolated High-Speed CAN Transceiver | NXP | 16-SOIC
The NXP TJF1052IT/1Y is a galvanically isolated high-speed CAN (Controller Area Network) transceiver housed in a 16-pin SOIC wide-body (7.50 mm width) package. Per the NXP datasheet, it provides 1000 Vrms of galvanic isolation between a CAN protocol controller and the physical two-wire CAN bus, delivering 2 Mbps data rate capability with 20 kV/µs common-mode transient immunity (CMTI). The device integrates NXP's proprietary isolation technology with the proven TJA1052 CAN physical layer, eliminating the need for a separate digital isolator and isolated DC-DC power supply on the bus side. A CAN transceiver (also called a CAN PHY) is the physical-layer interface between a CAN protocol controller and the differential CAN bus. In industrial systems, galvanic isolation between the low-voltage controller domain and the high-voltage bus domain protects sensitive microcontrollers from ground loops, surge events, and high common-mode voltages. The TJF1052i family extends the standard CAN transceiver by embedding this isolation barrier inside the IC, simplifying PCB layout and reducing BOM count compared to discrete isolator-plus-transceiver designs. Key features include integrated 1 kVrms isolation, 2 Mbps CAN FD (Flexible Data-rate) capability, low loop delay suitable for CAN FD frames, thermal protection, bus-dominant time-out, and a silent mode for selective wake-up. The device supports the ISO 11898-2 physical-layer standard and is specifically targeted at industrial automation, energy distribution, and medical equipment applications where reinforced isolation is mandatory. Internally, the TJF1052i combines a capacitive- or transformer-based isolation barrier with a CAN transceiver core on a single silicon die. The wide-body SOIC package provides the required creepage and clearance distances for 1 kVrms isolation, while the exposed pad aids thermal dissipation during sustained bus transmission. The result is a CAN transceiver that satisfies both functional isolation and basic insulation requirements in a single chip. Typical applications include industrial PLC communication modules, grid-tied smart-meter networking, photovoltaic inverter CAN buses, battery management system (BMS) communication links, electric-vehicle charging-station controllers, and isolated sensor networks in process automation. Designers reach for the TJF1052i when they need CAN connectivity in a high-voltage environment without the complexity of a multi-chip isolated solution. When designing with this part, mind the wide-body 7.50 mm SOIC footprint - it is wider than a standard 150-mil SOIC, so PCB land pattern and creepage must accommodate it. Also confirm that the upstream 5 V or 3.3 V controller rail is well decoupled; the isolated bus side derives its own internal supply through the on-chip isolation transformer/charge pump, so no external isolated supply is required.
TJF1052IT/5Y - Isolated CAN Transceiver 2Mbps 5kV | NXP
The NXP TJF1052IT/5Y is a galvanically isolated high-speed CAN (Controller Area Network) transceiver delivering 2 Mbps data rate across a 5000 Vrms isolation barrier in a 16-pin SOIC (7.50 mm) package. It integrates a CAN protocol controller interface, isolated power, and isolated bidirectional logic signals in a single IC, eliminating the need for external digital isolators, isolated DC-DC converters, and discrete CAN transceivers on the same PCB. An isolated CAN transceiver is a device that bridges a host microcontroller's CAN protocol controller to the physical two-wire differential CAN bus while maintaining galvanic isolation (no direct electrical connection) between the high-voltage bus side and the low-voltage logic side. This category sits within the broader hierarchy of CAN transceivers -> automotive/industrial bus transceivers -> interface ICs -> wired communication ICs. Galvanic isolation is required for safety, ground-loop elimination, and noise immunity when the bus operates at high common-mode voltages relative to the host controller. Key features of the TJF1052IT/5Y include 20 kV/us common-mode transient immunity (CMTI), integrated DC-DC isolation power, ±58 V bus fault protection, and thermal shutdown. The device supports the ISO 11898-2 standard CAN physical layer and is compatible with both classic CAN and CAN FD (Flexible Data-rate) frames up to 2 Mbps. Power dissipation is bounded by the SOIC-16W package's thermal resistance, making it suitable for industrial automation nodes and battery management system peripherals. Architecturally, the TJF1052IT/5Y combines an on-chip coreless-transformer isolation barrier, an isolated CAN physical layer, and a fully integrated isolated power supply. This single-chip integration replaces the typical 3-chip solution (CAN transceiver + digital isolator + isolated DC-DC), reducing BOM count, PCB area, and design complexity while improving reliability through fewer solder joints. Typical applications include industrial automation PLC fieldbus nodes, solar inverter CAN interfaces, battery management system (BMS) slave modules in e-mobility, and railway signaling where reinforced isolation is mandatory. The wide bus fault tolerance also makes it suitable for 24 V truck and 48 V mild-hybrid automotive environments. When designing with this device, note that the integrated isolation removes the requirement for optocouplers, but the PCB layout must still preserve the 5 kV creepage and clearance at the package level. Decoupling capacitors close to the VCC pins on both sides of the isolation barrier are critical for stable CAN signal integrity. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet. Engineers comparing isolated CAN transceivers will find cross-reference data, parametric tables, and design guidance consolidated for accelerated part selection and PCB reuse.
TLE6212XUMA1 - ABS/TC/ESC Sensor Interface IC | Infineon
The Infineon Technologies TLE6212XUMA1 is an automotive ABS, traction-control, and electronic-stability-control sensor interface IC with voltage input and voltage output functions, supplied in a 64-pin PG-LQFP package. The verified source data identifies it as an IC SENSOR FOR ABS/TC/ESC device and places it in the sensor and detector interface category. A sensor interface IC is an integrated circuit that connects physical or resistive sensing elements to an automotive control unit. In this product class, the interface device conditions sensor-related signals and supports communication between sensors and a controller. The TLE6212XUMA1 is associated with ABS, TC, and ESC systems, where accurate wheel-speed sensing is important for braking, traction, and vehicle stability control. Its voltage-input and voltage-output classification distinguishes it from purely digital sensor-interface devices. The verified distributor information confirms the device family and package, including the PG-LQFP-64 designation. Detailed electrical limits, internal architecture, supported sensor resistance, diagnostic behavior, supply range, and timing specifications were not included in the supplied verified data and must therefore be confirmed against the manufacturer datasheet before design release. The product is presented here with an explicit separation between verified facts and unavailable technical parameters. Typical automotive uses include ABS wheel-speed sensing, traction-control systems, electronic stability control, and vehicle motion-control electronic control units. The relevant design task is to verify that the selected sensor, wiring, connector, grounding, filtering, and diagnostic strategy all match the device requirements. Automotive production designs should also validate environmental, EMC, functional-safety, and supplier-specific requirements using the manufacturer’s official documentation. The PG-LQFP-64 package requires a PCB footprint, pin-1 orientation, exposed-pad or thermal-land treatment, and assembly process compatible with Infineon’s package drawing and recommended land pattern. Do not infer pin functions from the distributor category text alone; use the official TLE6212 datasheet and package drawing for schematic capture, PCB layout, and production inspection. This page consolidates the verified product identity, distributor availability references, package information, application context, and data gaps for engineering review. It is intended to support component selection and sourcing while avoiding unsupported claims about electrical performance, lifecycle status, pricing, or drop-in alternatives.
TLE6250PG - 1Mbaud CAN Transceiver | Infineon | DSO-8
Infineon Technologies TLE6250PG is a 1/1 high-speed CAN transceiver with 1 Mbaud operation, a 4.5 V to 5.5 V supply range, standby support, and an 8-pin DSO-8 package. The device interfaces a host controller with a high-speed CAN bus through one transmit driver and one receive comparator. According to the Infineon TLE6250 datasheet, it is intended for ISO 11898 systems and supports both automotive and industrial communication equipment. A CAN transceiver is an interface IC that converts logic-level transmit and receive signals into physical bus signals, then converts received bus states back into controller-compatible logic. In the product hierarchy, the TLE6250PG belongs to CAN transceivers, interface transceivers, interface ICs, and semiconductors. This position places it between a CAN controller or microcontroller and the differential CAN bus wiring. Key characteristics include one transmitter and one receiver, operation up to 1 Mbaud, a nominal 5 V supply range of 4.5 V to 5.5 V, and compatibility with high-speed CAN systems. The PG version is supplied in the compact DSO-8 outline identified by DigiKey as PG-DSO-8-16. The verified product listings also describe a cut-tape package option for TLE6250PG and identify it as a standard high-speed CAN interface IC. The transceiver separates the controller-side digital domain from the bus-side differential domain. Its TXD input accepts the controller's transmit command, while RXD provides the controller with a received bus state. STB provides standby control, and the remaining bus-side and supply pins connect the device to the CANH and CANL network. This division of responsibilities allows a host processor to use ordinary CMOS-compatible I/O while the transceiver handles the physical CAN bus levels. Typical applications include automotive body and comfort electronics, industrial automation controllers, CAN-connected sensors, engine-control modules, diagnostic equipment, and embedded CAN gateways. The 1 Mbaud rate is suitable for high-speed control and diagnostic networks, although actual bus length, termination, topology, and propagation delay must be considered when selecting cable length and bit rate. For PCB design, place the transceiver close to the CAN connector and preserve short, symmetrical CANH and CANL routing. Use the application information in the Infineon TLE6250 datasheet for decoupling and termination values. Avoid long stubs, maintain the required 120 ohm bus termination at both physical ends, and provide adequate creepage and clearance where automotive vibration, temperature, or transient requirements apply. This page consolidates verified manufacturer and distributor information, explicit data gaps, package details, sourcing links, and application guidance. It also distinguishes the TLE6250PG from related TLE6250 variants so engineers can verify standby, wake-up, and pin-level differences before committing a design to production.
TLE6250PGV33 - 1 Mbit/s CAN Transceiver | Infineon
The Infineon TLE6250PGV33 is a high-speed CAN transceiver for 12 V and 24 V automotive and industrial networks, supporting differential CAN communication at up to 1 Mbit/s in a PG-DSO-8 package. The device provides a 5 V transceiver supply, standby operation, RoHS-compliant construction, and compatibility with ISO 11898. A CAN transceiver is an interface IC that connects a host controller's digital CAN signals to a physical differential bus. It belongs to the CAN interface transceiver class, then network and bus interface ICs, and ultimately the broader semiconductor and communication-interface ecosystem. This conversion layer handles bus-level voltage signaling while allowing automotive or industrial control electronics to operate from logic-level pins. The TLE6250 family is optimized for high-speed differential-mode data transmission. According to the Infineon manufacturer datasheet, the transceivers are monolithic integrated circuits offered in PG-DSO-8 packaging with the same functionality as the bare-die versions. Their ISO 11898 compatibility makes them suitable for established CAN network architectures. Verified distributor information identifies the TLE6250PGV33 as an in-stock, 1 Mbit/s CAN transceiver with standby capability, a 5 V interface supply, automotive-temperature positioning, and a price beginning at $0.2485. The Infineon product listing for the related TLE6250G-V33 confirms 12 V and 24 V CAN compatibility, 1 Mbaud operation, ISO 11898 support, and EMC performance. Typical uses include automotive body-control modules, electronic control units, industrial automation controllers, CAN gateways, diagnostic interfaces, and distributed sensor networks. In these systems, the transceiver translates between CAN controller TXD and RXD signals and the bus's differential CANH and CANL conductors. Designers should verify the complete pin mapping, supply sequencing, bus termination, and transceiver-mode logic against the manufacturer datasheet before layout release. A common 120-ohm termination is normally placed at each end of the CAN bus, while the transceiver itself must be positioned to minimize differential-loop area and maintain controlled return-current paths. This page consolidates the verified manufacturer and distributor information, a pin-compatible replacement assessment, application guidance, and practical design notes that help engineers evaluate TLE6250PGV33 beyond a basic distributor listing.
TLE6251DS - 1 Mbaud CAN Transceiver | Infineon
The Infineon TLE6251DS is a high-speed CAN transceiver operating up to 1 Mbaud in a PG-DSO-8 package, with ISO 11898-2 and ISO 11898-5 compliance for automotive and industrial networks. The verified source data identifies bus wake-up capability, differential transmission and reception, a 4.75 V to 5.25 V supply range, standby operation, and suitability for automotive temperature conditions. Its 5 V interface serves as the physical-layer bridge between a CAN protocol controller and the differential CANH and CANL bus conductors. A CAN transceiver is a physical-layer interface IC that converts logic-level TXD and RXD signals into balanced bus signals and converts received bus states back into a controller-readable signal. Within the hierarchy of interface ICs, CAN transceivers connect digital communication controllers to robust wired networks. They must combine high-speed differential signaling, common-mode rejection, bus fault tolerance, low standby demand, and wake-up capability for dependable vehicle and industrial communication. Key verified features include operation to 1 Mbaud, compatibility with ISO 11898-2 and ISO 11898-5, a nominal 5 V architecture, and bus wake-up support. The automotive positioning is significant because designers can evaluate the part for vehicle network nodes, but the supplied evidence does not state its exact transceiver count, ESD rating, loop-delay limits, standby current, or junction-temperature limits. Those parameters must be checked in the manufacturer datasheet before final circuit qualification. The TLE6251DS is intended to sit between a host CAN controller and a two-wire CAN bus. Its TXD input accepts controller signaling, while RXD provides receive-state information to the controller. Differential bus operation reduces sensitivity to common-mode noise relative to a single-ended interface. When bus wake-up is required, a qualified network supervisor, termination network, and supply arrangement must support the transceiver's low-power behavior; exact timing values are unavailable in the verified dataset. Typical uses include automotive body and powertrain control modules, industrial automation controllers, vehicle gateways, distributed sensors, embedded CAN nodes, and diagnostic equipment. For a new high-speed CAN design, use ISO 11898-2 or ISO 11898-5 as the governing system requirement and verify physical-layer timing against the selected controller. Do not substitute a transceiver solely by SOIC-8 package fit; standby, wake-up, fault behavior, and pin functions must also match. The principal design check is the complete signal path: controller timing, transceiver propagation delay, bus length and topology, termination, common-mode environment, decoupling, and grounding. Place the device close to the bus connector and controller interface, provide the datasheet-required supply bypassing, and route CANH and CANL as a compact differential pair away from switching nodes. This page consolidates the verified manufacturer description, distributor specifications, price observation, and cross-reference findings into an engineering-oriented selection record. It also distinguishes verified facts from missing electrical details and identifies replacement candidates that still require manufacturer-based pin and timing validation.
TLE6251DST - 1 Mbps CAN Transceiver | Infineon | Automotive
The Infineon TLE6251DST is a 1 Mbps high-speed CAN transceiver with bus wake-up, supplied from 4.75 V to 5.25 V and packaged in an 8-pin PG-DSO-8 surface-mount package. It provides one CAN transmitter and one receiver, full-duplex operation, and 200 mV receiver hysteresis for noise-tolerant bus signaling. The component is designed to interface a CAN protocol controller with a physical CAN bus in automotive and industrial systems. A CAN transceiver is an interface IC that converts logic-level signals from a CAN controller into differential bus signals and converts received differential bus signals back into logic levels. In the product hierarchy, the TLE6251DST belongs to the CAN transceiver class, then network interface ICs, then interface ICs and semiconductors. Its high operating temperature range of -40°C to +150°C also supports demanding vehicle and industrial environments. Key characteristics include support for the CAN protocol at up to 1 Mbaud, full-duplex communication, 200 mV receiver hysteresis, and bus wake-up functionality. Bus wake-up allows a low-power node to detect activity on the CAN bus and signal the host controller, helping reduce overall vehicle energy consumption. The 8-pin PG-DSO-8 package also offers a compact footprint for automotive electronics modules. The TLE6251D is positioned as a high-speed CAN physical-layer interface compatible with ISO 11898-2 and ISO 11898-5, as identified by Infineon's official product page. These references describe CAN physical-layer behavior, while the device itself bridges the digital controller and physical bus. Its 4.75 V to 5.25 V supply range suits regulated 5 V automotive electronics. Typical uses include powertrain and body-control modules, electric-vehicle control units, industrial automation controllers, robotics, and diagnostic equipment. In each case, the transceiver handles the physical CAN layer while a microcontroller or dedicated CAN controller handles frames, arbitration, error handling, and higher-level protocols. PCB design must preserve the CAN bus differential symmetry and provide appropriate termination and common-mode behavior. The transceiver's wake-up function should also be evaluated against the host's low-power strategy, because incorrect sleep-mode configuration can prevent remote bus activity from waking the node. This page consolidates the verified Infineon specifications, distributor availability references, application guidance, and drop-in comparison information into a design-focused component reference. It also distinguishes verified electrical facts from specifications that require confirmation from the manufacturer datasheet.
TLE6251DSXT - 1Mbit/s CAN Transceiver | Infineon
The Infineon TLE6251DSXT is a high-speed CAN transceiver rated for differential-mode data transmission and reception up to 1 Mbaud in a PG-DSO-8 surface-mount package. Designed for automotive and industrial networks, it provides the physical-layer interface between a CAN protocol controller and the differential CANH and CANL bus conductors. The related TLE6251DS family also supports bus wake-up and is identified by Infineon as compatible with ISO 11898-2 and ISO 11898-5. A CAN transceiver is an interface IC that converts logic-level TXD and RXD signals used by a CAN controller into the differential voltage used on a CAN bus, while converting received bus levels back into a controller-compatible signal. Within the hierarchy of CAN interface ICs, transceivers, network interfaces, and semiconductors, the device bridges digital controller logic and a robust differential physical layer. The verified product information identifies a maximum signaling rate of 1 Mbaud, CAN TX/RX operation, standby capability, 5 V automotive supply context, and bus-wake-up functionality. These features suit conventional high-speed CAN networks in vehicle electronics, industrial automation, embedded control, and diagnostic systems. The monolithic PG-DSO-8 implementation also consolidates the bus interface into a compact surface-mount footprint. TLE6251DSXT is the orderable suffix associated with the TLE6251DS device family. Because the suffix encodes ordering and packaging information, engineers should confirm the exact package, pin assignment, temperature grade, and tape orientation against the Infineon ordering information before releasing production artwork or a BOM. The verified sources do not provide every electrical limit or order-code detail needed for a complete component qualification record. In an automotive ECU, the transceiver sits beside a CAN controller and connects its TXD and RXD pins to CANH and CANL. The controller emits frames, the transceiver drives the differential bus, and received dominant or recessive states return through RXD. This arrangement isolates the controller from the physical signaling conditions while supporting network communication at up to 1 Mbaud. PCB implementation should follow the manufacturer layout guidance, provide a low-impedance connection between transceiver and bus connector, and place protection or filtering components where they do not distort edge rates. The CAN bus also requires correct termination, common-mode margin, and topology control. Exact voltage limits, loop-delay limits, and EMC test conditions should be taken from the manufacturer datasheet rather than inferred from the family description. This page combines verified manufacturer and distributor information, same-footprint replacement constraints, practical interface guidance, and transparent data gaps. It is intended to accelerate component identification and first-pass design review while directing engineers to authoritative documentation for final electrical, environmental, and qualification decisions.
TLE6251GNT - High-Speed CAN Transceiver | Infineon
The Infineon TLE6251GNT is a 1/1 high-speed CAN transceiver with wake detection, supplied in the PG-DSO-14-13 14-pin SOIC package. The verified source data identifies a 4.75 V to 5.25 V supply range and an operating temperature range of -40 °C to +150 °C. Its interface role places it between a CAN protocol controller and a physical CAN bus, while the listed 1/1 transceiver classification indicates one transmitter and one receiver channel. A CAN transceiver is an interface IC that converts logic-level signals from a CAN controller into the differential electrical signaling used on a CAN bus, then converts received bus signals back into controller-compatible logic. The TLE6251GNT therefore belongs to the CAN interface IC, transceiver, interface IC, and semiconductor hierarchy. Wake detection is specifically named in the manufacturer-oriented search result, supporting use in systems that require bus wake-up behavior. The verified data identifies the device as a high-speed CAN transceiver and a 1/1 transceiver with PG-DSO-14-13 packaging. The distributor listing also describes the part as associated with Infineon Technologies and Rochester Electronics. These details are useful for board-level sourcing and footprint matching, although electrical limits beyond the supplied voltage and temperature data are not available in the provided verification payload. Typical CAN applications include industrial automation equipment, automotive electronics, embedded controllers, factory communication networks, and distributed sensor or actuator systems. In these systems, the transceiver provides the physical-layer interface while the CAN controller handles protocol framing, arbitration, error handling, and message processing. A suitable companion MCU or CAN controller must be selected with compatible logic levels and CAN timing. Designers should verify the complete pinout, recommended external components, bus termination, loopback behavior, fault handling, and electrical limits from the manufacturer datasheet before final release. The package and pin compatibility of any substitute must be checked against the exact device variant rather than inferred only from a similar product family name. This page synthesizes the verified distributor and search results with a traceable source list and explicitly marks unspecified parameters rather than estimating them. It is intended to support initial component identification, sourcing comparison, and engineering review; it does not replace the complete Infineon datasheet or application-specific qualification.
TLE6255G - 33kbit/s Single-Wire CAN Transceiver | Infineon
The Infineon TLE6255G is a single-wire CAN transceiver rated for bus speeds up to 33 kbit/s, with a high-speed mode extending operation to 100 kbit/s, a typical 28 V supply range, and operation up to 125 °C in a P-DSO-14-9 package. It is designed for low-speed vehicle communication networks where one conductor carries both transmit and receive functions. A single-wire CAN transceiver is an automotive network interface that combines a CAN controller-facing logic interface with the physical-layer driver and receiver used on a SWCAN bus. In the broader electronics hierarchy, it belongs to the CAN transceiver family, interface IC category, and automotive communication semiconductor ecosystem. Its purpose is to connect digital control electronics to a wired vehicle network while converting logic signals into a robust bus waveform and returning the received bus state to the controller. The verified feature data identifies excellent EMC performance, a 33 kbit/s normal bus-speed limit, a 100 kbit/s high-speed-mode limit, a 28 V typical operating-supply range, and an ambient operation range extending to 125 °C. These characteristics make the device relevant to body, comfort, lighting, seat, and other low-speed automotive networks. The high-speed mode provides additional flexibility when a network requires faster communication than the standard single-wire mode supports. The TLE6255G is packaged as PG-DSO-14-9 and is identified by distributors as a one-channel full CANbus transceiver. Its automotive-oriented electrical interface is intended to bridge a controller or MCU with the vehicle’s single-wire CAN network. System designers should still verify the exact electrical limits, pin functions, bus timing, termination or biasing arrangement, and application circuit against the manufacturer datasheet before releasing a production PCB. Typical implementations place the transceiver beside an automotive MCU or CAN controller and connect its logic interface to that controller while routing the single-wire bus pin to the vehicle network. Because external networks introduce wiring length, protection, grounding, and electromagnetic-compatibility constraints, PCB trace routing and connector protection are as important as nominal logic compatibility. The 125 °C ambient capability is useful in demanding vehicle environments, subject to the package and board-level thermal limits documented by Infineon. A key design consideration is to preserve the manufacturer’s recommended decoupling and bus-interface layout. Keep the transceiver close to its supply and signal-routing paths, use a stable ground reference, and validate waveform integrity with the intended bus load and cable harness. Do not assume that a logically similar CAN transceiver is a drop-in replacement unless its package, pinout, supply behavior, bus timing, and protection characteristics have been independently checked. This page consolidates the verified TLE6255G search results, package and feature information, application guidance, and verification notes into a practical product reference. It does not invent electrical limits or pricing that were absent from the supplied source data; unavailable values are explicitly marked for engineering follow-up.
TLE6286G - LIN Transceiver with LDO | Infineon Technologies
The Infineon Technologies TLE6286G is a LIN transceiver with an integrated standard voltage regulator, supplied in a PG-DSO-16-11 package. It combines a single-wire LIN bus transceiver with regulator control and supports LIN transmission rates up to 20 kBaud. The verified source data identifies the device as compatible with the LIN specification and ISO 9141 functions, while also providing a low-current sleep mode and a short-circuit-proof regulator output. A LIN transceiver is an interface IC that connects a low-cost, single-wire vehicle network to a host microcontroller. LIN, or Local Interconnect Network, belongs to the broader automotive communication hierarchy: LIN transceiver -> wired vehicle-network interface -> automotive electronics. Integrating the transceiver and a standard voltage regulator can reduce the number of discrete components in a LIN slave node while providing a controlled supply for the local interface electronics. The principal verified features include a maximum transmission rate of 20 kBaud, LIN and ISO 9141 compatibility, very low sleep-mode current consumption, a regulator control output, and short-circuit-proof behavior. The TLE6286G is categorized by DigiKey as a half-LIN-bus transceiver. The combination is suited to distributed vehicle systems where a microcontroller requires local bus communication and a stabilized supply rail. Technically, the TLE6286G integrates two closely related functions on one die: the physical-layer LIN transceiver and a standard voltage regulator. The single-wire bus interface handles communication up to 20 kBaud, while the regulator section supports the node's local supply requirements. Exact input-voltage, output-voltage, current, and timing values were not present in the supplied search excerpts and therefore remain marked as data needed rather than being inferred. Typical applications include LIN slave nodes in body and comfort systems, door and seat modules, climate-control interfaces, ambient-sensing nodes, and other low-bandwidth automotive electronics. The integrated regulator output can support local circuitry when the node also needs a controlled supply, although the final capacitor, load, and thermal design must follow the manufacturer datasheet. A key design consideration is that the regulator and transceiver share a compact DSO-16 footprint, making decoupling, exposed-pad thermal management, and bus-EMI layout essential. Designers should also verify LIN waveform timing, wake-up behavior, supply tolerances, and fault-mode behavior against the manufacturer datasheet before releasing production hardware. This page combines verified distributor and manufacturer-result data with practical selection guidance, packaging information, technical comparison points, and engineering design notes. It also distinguishes explicitly confirmed specifications from electrical values that require confirmation from the full Infineon Technologies datasheet.
TLE7250VSJ - 2 Mbit/s CAN FD Transceiver, PG-DSO-8 | Infineon
The Infineon TLE7250VSJ is a high-speed CAN FD transceiver supporting data rates up to 2 Mbit/s, compliant with ISO 11898-2 and housed in a PG-DSO-8 package. It features a digital supply input V_IO and a power-save mode, and is designed to fulfill the enhanced physical layer requirements of CAN FD networks used in automotive body, chassis and powertrain ECUs. According to the Infineon datasheet, the TLE7250V family (TLE7250VLE and TLE7250VSJ) meets or exceeds ISO 11898-2 requirements and supports data rates up to 2 Mbit/s with optimized slew rates for large HS-CAN networks. A CAN transceiver is a physical-layer interface IC that sits between a CAN protocol controller and the differential CAN bus wires (CANH, CANL). It converts single-ended TXD/RXD logic levels from the microcontroller into differential bus voltages defined by ISO 11898-2, and vice versa for reception. The TLE7250VSJ's optimized slew rate limits electromagnetic emission (EME) while preserving signal integrity at 2 Mbit/s, making it suitable for mixed-supply HS-CAN networks where 5 V microcontrollers and 3.3 V MCUs coexist on the same bus. Key features include low EME / high EMI immunity, an integrated V_IO supply input for direct interfacing with 3.3 V or 5 V microcontrollers without level shifters, three operating modes (normal, receive-only, power-save) selectable via NEN and NRM pins, AEC-Q100 qualification for automotive use, and RoHS-compliant halogen-free PG-DSO-8 packaging. Built on Infineon Smart Power Technology (SPT), the device integrates strong ESD and electromagnetic immunity on-chip. Typical applications include automotive gateway ECUs, body control modules, powertrain CAN networks, ADAS sensor CAN buses, and industrial CAN FD nodes. The PG-DSO-8 package supports automated optical inspection (AOI) of solder joints, simplifying automotive-grade manufacturing. When designing the bus termination, ensure 120 ohm termination at each end of the CAN segment and place decoupling capacitors close to VCC and V_IO pins to maintain EMI performance. This page synthesizes distributor pricing, drop-in alternatives and application notes not found in the manufacturer datasheet, helping engineers select, source and lay out the TLE7250VSJ quickly for automotive CAN FD designs.
TLE7259-2GU - 20 kbaud LIN Transceiver | Infineon
The Infineon TLE7259-2GU is a single-channel LIN transceiver for in-vehicle networks, operating from 7 V to 27 V with one driver and one receiver. It supports data rates from 2.4 kBaud to 20 kBaud according to the SAE J2602 standard and is packaged in an 8-pin SOIC, designated PG-DSO-8. A LIN transceiver is the physical-layer interface between a microcontroller or LIN protocol controller and the vehicle's LIN bus. The TLE7259-2GU converts controller-side serial signals into LIN bus levels, receives bus signals for the controller, and provides the electrical characteristics required by an in-vehicle network. It belongs to the broader hierarchy of interface IC, transceiver, communications transceiver, and automotive network interface. The TLE7259-2GU is a follow-up product to the TLE7259-2GE and provides the same functions and pin compatibility. Verified data identifies it as a full-duplex, single-transceiver device with a 10.4 kBaud listed data rate in distributor listings, while the manufacturer datasheet describes operation from 2.4 kBaud to 10.4 kBaud according to SAE J2602. The distinction matters because the TLE7259-2GU is specifically positioned for the stated LIN network range rather than a general-purpose CAN interface. The device is intended for automotive electronic control units, body modules, door modules, seat modules, lighting controllers, sensor interfaces, and other low-speed vehicle-network nodes. Its 8-pin SOIC package supports conventional surface-mount assembly, while the 7 V to 27 V supply range matches the verified component specification. The operating temperature range is listed as -40 C to 150 C in the verified GlobalSpecs data, making it relevant to automotive temperature environments. For PCB design, preserve the verified pin compatibility with the TLE7259-2GE and place the transceiver close to the LIN bus connection. The LIN bus requires an appropriate transceiver-level bus interface, protection strategy, and decoupling arrangement defined by the surrounding vehicle-network design. The TLE7259-2GU is a surface-mount SMD device in cut-reel packaging according to the verified source data. Use the manufacturer datasheet for exact pin names, application circuitry, electrical limits, and external-component recommendations before releasing a design. This product page combines verified specifications, source links, package information, and application context for engineers evaluating the TLE7259-2GU. It also distinguishes the TLE7259-2GU from merely functional interface alternatives and highlights the importance of confirming pin compatibility, supply range, protocol, and automotive requirements during substitution.
TLE7259-3LE - 20 kbps LIN Automotive Transceiver | Infineon
The Infineon TLE7259-3LE is an automotive LIN transceiver supporting data rates from 2.4 kbps to 20 kbps, with an 8 μA sleep current and integrated wake-up and protection features. It is designed for in-vehicle networks and operates from a 5.5 V to 27 V supply range in an 8-pin PG-TSON surface-mount package. A LIN transceiver, also called a Local Interconnect Network physical-layer interface, connects a vehicle’s protocol controller to the physical LIN bus. It combines a bus driver, receiver, wake-up logic, and protection functions into one device. In the vehicle electronics hierarchy, the TLE7259-3LE belongs to the interface-IC family and connects low-rate serial-control networks to modules such as door controls, seat controls, lighting modules, and body-control systems. The verified TLE7259-3 features include a 20 kbps maximum data rate, an 8 μA sleep current, and high EMC performance for LIN networks. Its integrated wake-up and protection features support low-power body-network operation and robust communication in electrically demanding vehicle environments. The 5.5 V to 27 V operating supply range allows use in conventional automotive electrical systems where transient and EMI conditions must be considered. The device provides a physical bus-driver interface between the LIN protocol controller and the LIN bus. At the protocol level, the host controller handles framing, addressing, and higher-layer messaging, while the transceiver translates digital controller signals into LIN bus levels and returns received bus information through RXD. The integrated protection and wake-up functions reduce the need for separate interface circuitry, although external network protection and layout practices still matter in production designs. Typical uses include LIN door modules, central locking, window and seat controls, ambient-lighting controllers, climate-control peripherals, body-control units, and other low-cost automotive subnetworks. The TLE7259-3LE is most appropriate when the design needs LIN communication between a low-rate embedded controller and distributed vehicle peripherals. For PCB implementation, place the transceiver near the LIN connector or bus routing point, keep the LIN trace short and isolated from sensitive analog and high-speed digital signals, and provide the external pull-up and bus capacitance required by the application. Verify sleep-current behavior, bus timing, wake-up polarity, EMC performance, and supply decoupling against the manufacturer datasheet. This page combines verified manufacturer specifications, sourcing context, application guidance, and drop-in-replacement analysis. It is intended to help engineers evaluate the TLE7259-3LE for automotive LIN designs while clearly separating verified values from information that still requires design-specific verification.
TLE7259G - 20 kBaud LIN Transceiver | Infineon | Automotive
The Infineon Technologies TLE7259G is an automotive LIN transceiver supporting data rates from 2.4 kBaud to 20 kBaud, with a specified 3.5 V to 5.5 V operating range, integrated wake-up functionality, and integrated protection features. It is packaged in an 8-pin SOIC and is intended for Local Interconnect Network nodes in in-vehicle communication systems. The verified source identifies the TLE7259G as a LIN transceiver, while several detailed electrical limits and pin assignments remain unavailable in the supplied data. A LIN transceiver is an interface IC that connects a microcontroller UART to a LIN bus. LIN, or Local Interconnect Network, is a low-cost, single-wire vehicle network commonly used for sensors, actuators, body electronics, and comfort systems. The transceiver translates logic-level signals between the host controller and the LIN physical bus, while wake-up and protection functions support reliable operation in electrically harsh environments. Its 20 kBaud maximum rate matches the source description for in-vehicle LIN networks. The key verified characteristics are the 2.4 kBaud-to-20 kBaud data-rate range, 3.5 V-to-5.5 V supply range, integrated wake-up, integrated protection, and 8-pin SOIC construction. These features make the device applicable to distributed vehicle nodes where a host MCU requires a standardized LIN physical layer. The source does not provide verified values for transceiver mode, sleep current, bus thresholds, propagation delay, ESD rating, or absolute maximum ratings, so those parameters are not inferred here. TLE7259G is most relevant to body and comfort modules, sensor interfaces, actuator controllers, door and window modules, climate-control systems, and other LIN subnets. The host microcontroller handles LIN frame generation and protocol timing; the transceiver supplies the physical-layer connection. Designers must confirm the complete LIN electrical specification, pinout, external components, supply sequencing, and protection requirements against the manufacturer datasheet before production release. For PCB implementation, place the transceiver close to the LIN bus connection and route the single-wire bus away from sensitive analog and high-speed digital signals. The LIN bus requires an appropriate pull-up arrangement and protection strategy; exact resistor and protection values should follow the verified datasheet and system-level EMC requirements. Keep the supply and ground return paths short, and verify the device's wake-up behavior in the intended low-power architecture. This page combines the verified TLE7259G source descriptions, pricing references, package information, and cross-reference findings with engineering selection context. The supplied data does not establish enough verified information to populate every electrical specification, complete pinout, lifecycle classification, or qualified drop-in alternative without risking an inaccurate replacement recommendation.
TLE7259GNT - 20kBd LIN Transceiver, P-DSO-8 | Infineon
Infineon Technologies TLE7259GNT is an automotive-grade LIN bus transceiver operating at 20 kBd in an 8-pin P-DSO-8 surface-mount package. Verified distributor data identifies a 1/1 transceiver arrangement, full LIN-bus operation, an 8-terminal gull-wing package, and an operating-temperature range of -40°C to 150°C. The device belongs to the LIN interface-transceiver category and converts between a host controller's logic-level UART signals and the physical LIN network. Its principal electrical values, including supply voltage limits, receiver hysteresis, output-driver details, and sleep or wake behavior, were not included in the supplied verified records and therefore require confirmation from the manufacturer datasheet before design release. The public parts database labels TLE7259GNT obsolete or end-of-life, although distributor listings remain available. Engineers should treat lifecycle status, stock, and sourcing conditions as time-sensitive rather than assuming broad future availability. TLE7259GNT is associated with automotive LIN subnets, body electronics, climate controls, seat modules, door modules, lighting controllers, and sensor gateways where a standardized low-speed serial bus connects distributed nodes. Its 20 kBd LIN rate is suitable for control and status traffic rather than high-bandwidth payloads. The package keeps the physical implementation compact, but successful deployment still depends on correct transceiver pin mapping, bus termination, reference-ground handling, ESD protection, decoupling, and compliance with the LIN network requirements used by the vehicle platform. This page summarizes verified distributor and database records, available sourcing information, documented package and protocol details, and the unresolved datasheet parameters that must be checked before substitution or PCB release.
TLE7259GT - 20 kBd LIN Transceiver | Infineon | Automotive
The Infineon TLE7259GT is a half-duplex LIN bus transceiver with one transmitter and one receiver, a 7 V to 27 V supply range, and a maximum transmission rate of 20 kBaud. The device is packaged for surface-mount assembly in an 8-pin DSO/SOIC-style package and is supplied in tape-and-reel packaging. It complies with LIN specification versions 1.3, 2.0, and 2.1, while also supporting the ISO 9141 K-line function. A LIN transceiver is an interface IC that connects a host microcontroller to a low-cost, single-wire automotive communication bus. LIN belongs to the broader CAN and automotive-network hierarchy: a CAN bus is a high-speed, multi-node network, while LIN uses a slower serial protocol optimized for cost-sensitive distributed vehicle subsystems. The TLE7259GT converts logic-level requests from a controller into LIN-bus signals and converts received bus levels into logic signals for the controller. The TLE7259GT supports transmission rates through 20 kBaud and includes LIN specification compatibility for versions 1.3, 2.0, and 2.1. Its 7 V to 27 V operating supply range accommodates vehicle battery environments. Additional cited features include K-line support under ISO 9141, very high ESD robustness, and very low electromagnetic emission. These characteristics make the device relevant to LIN nodes requiring protocol compatibility and strong protection against conducted or capacitive bus disturbances. Technically, the device combines a bus-side transmitter and receiver with the interface needed for an embedded host. A microcontroller can control bus dominance, monitor received frames, detect communication errors, and implement LIN scheduling. Because LIN commonly operates from a vehicle supply, the 27 V maximum operating voltage provides additional margin relative to 5 V transceiver packages, although the final design must still account for load dump and transient requirements at the wiring interface. Typical applications include body-control modules, door and seat controllers, climate-control panels, lighting controllers, automotive gateways, and other distributed electrical subsystems. The K-line function broadens its utility in diagnostic or legacy vehicle interfaces, while the 20 kBaud rate matches common LIN physical-layer implementations. Designers should verify bus termination, supply decoupling, transceiver sleep behavior, and protection requirements against the manufacturer datasheet before layout release. The LIN bus wiring is sensitive to ground offsets, capacitance, reflections, and ESD events, so PCB placement and vehicle harness design remain as important as the nominal IC specification. This product page consolidates verified specifications, sourcing context, application guidance, and strict drop-in replacement criteria. Where the supplied web evidence does not establish a complete pin map, pricing schedule, or lifecycle designation, those details remain explicitly unverified rather than being inferred.
TLE7263E - Integrated CAN, LIN and LDO SBC | Infineon
The Infineon Technologies TLE7263E is an integrated HS-CAN, LIN, low-dropout regulator, and high-side switch system basis chip rated for a 13.5 V supply, housed in a PG-DSO-36-24 package. It provides a 5 V output rated at 150 mA, a standard 16-bit SPI interface, controller stop-mode support, and a 50 µA sleep mode. The integrated LIN transceiver includes a 30 kΩ pull-up resistor for fail-safe operation. A system basis chip is an automotive power and communication component that consolidates supply regulation, high-side switching, diagnostic interfaces, and network transceivers. In the hierarchy, this TLE7263E combines a LIN transceiver, high-speed CAN interface, two low-dropout voltage regulators, and a high-side switch to support centralized electrical architecture and body or comfort-system electronics. The principal verified features include compatibility with the LIN 2.0 specification and ISO 9141, a 13.5 V supply configuration, a 1 mA supply-current figure reported by a distributor index, and two integrated low-dropout regulators. The 16-bit SPI interface allows a host microcontroller to configure and monitor the system basis functions, while stop and sleep modes support reduced-power operating states. The TLE7263E consolidates several discrete automotive functions into one IC, reducing PCB area and the number of external network-interface components. Its 150 mA, 5 V regulator capability is suitable for low-power automotive loads, although it is not intended to power loads whose current exceeds that rating. The exposed-pad package also requires attention to PCB thermal design and copper placement. Typical uses include automotive body-control modules, door and seat controllers, climate-control electronics, lighting-control units, LIN-connected actuators, gateways combining LIN and CAN, and other low-voltage vehicle electronics. Designers should verify transceiver limits, regulator startup behavior, pin electrical limits, and watchdog operation directly against the manufacturer datasheet before production release. For layout, place the device close to protected vehicle-power entry, route high-current switched paths with adequate copper, and keep sensitive CAN and LIN nodes compact and isolated from switching edges. Confirm startup sequencing, diagnostic behavior, watchdog timing, and sleep-mode current in the target ECU environment. This page combines verified manufacturer-linked specifications, distributor package information, application guidance, and replacement-policy checks. It does not claim an unqualified drop-in alternative because the supplied cross-reference results did not verify five pin-compatible parts.
TLE7269G - Dual LIN Transceiver, 20 kBaud | Infineon
Infineon Technologies TLE7269G is a LIN 2.1-compliant dual LIN transceiver supporting data rates from 2.4 kBaud to 20 kBaud for in-vehicle networks. The device integrates wake-up and protection functions and is optimized for low electromagnetic interference and a sleep-mode current below 10 mA. It is supplied in a 14-pin PG-DSO package, also identified as PG-DSO-14-24 in distributor listings. A LIN transceiver, also called a LIN bus interface, belongs to the vehicle-network interface IC hierarchy and connects a microcontroller or cluster ECU to a low-speed serial network. It converts logic-level transmit and receive signals into physical LIN bus signals, while recovering incoming data for the host controller. The TLE7269G combines two LIN channels in one package, reducing board area where multiple vehicle subnets or redundant communication links are required. Key features include dual-channel operation, LIN 2.1 compliance, integrated wake-up capability, protection features, low EMI, and a sleep-mode current below 10 mA. Its data-rate range of 2.4 kBaud to 20 kBaud matches the operating range cited in the manufacturer datasheet. The very low leakage current on the bus pins also supports partially supplied LIN networks, helping nodes that remain unpowered avoid loading the active network. The TLE7269G is based on Infineon Smart Power Technology SPT, according to the manufacturer datasheet. This process combines digital control functions with automotive-grade power and interface robustness. The manufacturer specifically highlights excellent ESD robustness and high electromagnetic immunity, both important in vehicle electrical environments where cable-borne transients and radio-frequency coupling can disrupt low-speed communication. Typical uses include body-control modules, door and seat controllers, climate-control panels, lighting controllers, seat and door modules, and other ECUs connected through LIN subnets. The dual-channel configuration is particularly useful when an ECU needs two independent LIN endpoints or participates in more than one vehicle network segment. When designing around the TLE7269G, preserve the recommended external resistor, capacitor, and bus-termination arrangements from the manufacturer datasheet. Keep the LIN bus route away from sensitive analog signals and provide the required pull-up and wake-up components to avoid excessive bus loading. The low sleep current and bus leakage support low-power designs, but functional sleep and wake behavior must still be verified against the complete network topology. This page combines verified manufacturer and distributor facts with a focused comparison of the most relevant substitute candidates, application guidance, and practical interface-design notes. It distinguishes published characteristics from parameters that still require direct confirmation for a specific ordering code or design revision.
TLE8250G - 1 Mbit/s CAN Transceiver | Infineon | Automotive
The Infineon TLE8250G is a high-speed CAN transceiver with one transmitter and one receiver, data rates up to 1 Mbit/s, and ISO 11898-2 compliance in an eight-pin PG-DSO-8 surface-mount package. It serves as the physical-layer interface between a CAN protocol controller and a two-wire differential CAN bus. According to the Infineon product page and manufacturer datasheet, the device is designed for automotive and industrial networks, with low electromagnetic emissions and emissions-related interference, high electromagnetic immunity, and robust ESD protection. A CAN transceiver is a network interface IC within the broader communications-semiconductor hierarchy. It converts logic-level TXD and RXD signals into the differential CANH and CANL bus signals, then converts received bus levels back into a controller-compatible RXD signal. High-speed CAN is a two-wire differential network designed for robust, priority-based communication between electronic control units, where common-mode rejection and disturbance tolerance are central to reliable operation. The TLE8250G combines a 1 Mbit/s-capable CAN driver with a receiver interface and bus protection functions. Its symmetric CANH and CANL behavior supports low EMI in applications where electronic modules must coexist on a shared harness. The device supports partially supplied networks, an important characteristic for automotive systems where some nodes can be unpowered while others remain active. In power-down mode, receiver input resistors are switched off so the transceiver input becomes highly resistive, reducing unwanted loading of an inactive bus. Infineon Smart Power Technology combines bipolar and CMOS control circuitry with DMOS power devices on one monolithic circuit. The manufacturer describes this technology as supporting high ESD robustness and high electromagnetic immunity. The TLE8250G and its Smart Power Technology are stated to be AEC qualified. The transceiver also meets or exceeds ISO 11898-2 requirements and is offered in a RoHS-compliant PG-DSO-8 package, making it appropriate for electronic control units, body modules, gateways, sensors, and industrial automation interfaces. Use the TLE8250G when the PCB already expects an eight-pin PG-DSO-8 CAN interface and the bus operates at or below 1 Mbit/s. Designers should confirm the transceiver I/O voltage against their controller, preserve the CAN bus termination network, and follow the manufacturer’s layout guidance to minimize radiated emissions. Because only verified electrical limits, supply ranges, temperature ranges, and pin-level details are not included in the supplied search data, those values require confirmation in the manufacturer datasheet before release to production. The TLE8250G is also fully pin- and function-compatible with its Infineon predecessor, the TLE6250G, according to the verified manufacturer documentation. This predecessor relationship provides a documented upgrade path, but design reviews should still compare operating voltages, timing, transient immunity, and lifecycle requirements for the exact production variant. This page synthesizes manufacturer specifications, compatibility information, application guidance, and sourcing references that are not presented together on a distributor search page.