マイクロコントローラ

製品 (18756)

DSPIC33CH128MP508-I/PT - Dual-Core 16-Bit DSC, 80-TQFP | Microchip
DSPIC33CH128MP508-I/PT

DSPIC33CH128MP508-I/PT - Dual-Core 16-Bit DSC, 80-TQFP | Microchip

The Microchip Technology DSPIC33CH128MP508-I/PT is a high-performance dual-core 16-bit Digital Signal Controller (DSC) combining two independent dsPIC DSC cores (one master, one slave) on a single die, delivered in an 80-pin TQFP (12x12 mm) package with 0.5 mm pitch. The master core and slave core each operate at up to 200 MHz, with 152 KB of Flash memory (128 KB master + 24 KB slave) and 16 KB of RAM supporting complex closed-loop algorithms in real time. A Digital Signal Controller (DSC) is a hybrid MCU+DSP architecture that combines a microcontroller's deterministic control peripherals with a digital signal processor's MAC engine and SIMD instructions; in the 33CH family this is extended into a dual-core topology where the master runs the application/control loop while the slave executes time-critical math such as high-resolution PWM control loops or proprietary algorithm code. Key features include high-resolution PWM with 250 ps resolution (1 ns for slave), CAN FD support, four PGA/operational amplifiers, three DACs, four 12-bit 3.5 MSPS ADC modules, and a peripheral trigger generator (PTG). Functional Safety (FuSa) variants support IEC 61508 SIL 2/3 system designs. The chip is designed for systems where deterministic, sub-microsecond control loops must run in parallel with housekeeping code. The dual-core architecture uses a tightly-coupled MSI (Master-Slave Interface) mailbox FIFO that allows the cores to exchange data without contention, and the slave core can directly drive dedicated peripherals (PWM, ADC) for hard-real-time applications. Hardware DSP support includes dual 40-bit accumulators, barrel shifter, and DSP-aware addressing modes. Typical applications include digital switch-mode power supplies (PFC + LLC), wireless charging, motor control (FOC for PMSM/BLDC), drones, automotive sensors, and server PSUs. The functional safety variant is targeted at ISO 26262 systems. When designing with this device, reserve the slave core for time-critical control loops and use the master for housekeeping; this minimizes jitter and offloads work from the control ISR.

見積もり お問い合わせ
DSPIC33CH128MP508T-I/PT - Dual-Core 200MHz DSC, 152KB Flash | Microchip
DSPIC33CH128MP508T-I/PT

DSPIC33CH128MP508T-I/PT - Dual-Core 200MHz DSC, 152KB Flash | Microchip

The Microchip DSPIC33CH128MP508T-I/PT is a 16-bit dual-core Digital Signal Controller (DSC) combining a 180 MHz master core and 200 MHz slave core with 152 KB of Flash and CAN FD, housed in an 80-pin TQFP (12x12 mm) package. It integrates two independent dsPIC33C cores on a single die, enabling partitioning of real-time control loops and housekeeping tasks into physically separate processors for deterministic multi-motor or multi-converter designs. A Digital Signal Controller (DSC) is a hybrid device that combines the deterministic interrupt response and peripherals of a microcontroller (MCU) with the multiply-accumulate (MAC) engine, barrel shifter, and DSP library support of a Digital Signal Processor (DSP). The dsPIC33CH family extends this concept by adding a second on-chip dsPIC core, allowing complex control tasks such as field-oriented control (FOC) of multiple motors, digital power conversion, and functional-safety housekeeping to coexist on a single silicon die. In the broader taxonomy the part sits as: DSC -> microcontroller -> embedded processor -> semiconductor IC. Key features include 152 KB Flash program memory organized as 128 KB on the master core plus 24 KB shared with the slave core, CAN FD peripheral for high-throughput automotive and industrial networking, high-resolution PWM with 250 ps edge placement, and integrated op amps and 12-bit ADC for sensor interfacing. The functional-safety (FuSa) capability targets ASIL-B / SIL-2 designs by allowing the two cores to run independent diagnostics in lock-step or split tasks for cross-checking. The device uses a 3.3 V CMOS process and offers 12-bit ADC with up to 3.5 MSPS sampling, multiple high-speed analog comparators, and a dedicated peripheral trigger generator that minimizes CPU load in tight control loops. The 80-pin TQFP provides 69 digital I/O plus analog channels, sufficient for multi-phase power stages or dual-axis drives without external GPIO expanders. Typical applications include high-performance digital power supplies, server and telecom SMPS, wireless charging transmitters, drones and eVTOL motor controllers, automotive sensors and DC-DC converters, and multi-axis industrial servo drives. The dual-core architecture specifically accelerates applications that previously required two separate MCUs and a communication bus. When designing with this part, ensure that the master and slave core firmware images are linked consistently and that the slave core is brought out of reset only after its program memory is loaded. Use the Microchip MPLAB X IDE with the XC-DSC compiler and the dsPIC33CH Motor Control or Digital Power plug-in modules for evaluation. This page synthesizes verified distributor pricing, drop-in same-package alternatives, and practical dual-core firmware design notes that go beyond the manufacturer datasheet.

見積もり お問い合わせ
DSPIC33CH256MP205-E/M4 - Dual-Core 16-bit DSC, 328KB Flash | Microchip
DSPIC33CH256MP205-E/M4

DSPIC33CH256MP205-E/M4 - Dual-Core 16-bit DSC, 328KB Flash | Microchip

The Microchip Technology DSPIC33CH256MP205-E/M4 is a high-performance, dual-core 16-bit Digital Signal Controller (DSC) from the dsPIC33CH family, integrating a 100 MIPS main dsPIC DSC core and a 100 MIPS slave dsPIC DSC core in a single 48-pin UQFN (6x6 mm) package with exposed thermal pad. It features 328 KB of program Flash memory, 24 KB of SRAM, and CAN Flexible Data-Rate (CAN FD) support, and operates from a 3.0V to 3.6V supply with an automotive -40C to +125C (Grade 1) temperature range. A Digital Signal Controller (DSC) is a hybrid device that combines the deterministic interrupt response and rich peripheral set of a microcontroller with the computational throughput of a Digital Signal Processor (DSP). Positioned in the hierarchy microcontroller < DSC < DSP, the dsPIC33CH family targets real-time closed-loop control applications such as field-oriented motor control, digital power conversion, and high-performance sensor processing where math-intensive DSP routines and time-critical MCU housekeeping must coexist on the same silicon. Key features include dual independent cores that allow the slave to handle time-critical DSP loops (sensorless FOC, digital filtering, audio processing) while the master manages communication stacks (CAN FD, UART, SPI, I2C) and housekeeping. The on-chip 12-bit, 3.5 MSPS ADC, high-resolution PWM (250 ps edge resolution), and integrated op-amps reduce external component count, while hardware safety features such as live update Flash, ECC, and windowed watchdog support functional-safety (FuSa) system designs. The architecture uses a Harvard-bus dsPIC33 enhanced core with DSP engine, dual 16x16 MAC, single-cycle 40-bit accumulator, and zero-overhead loop control. The 100 MIPS per core delivers up to 200 MIPS aggregate throughput, supporting 2.4 GFLOPS theoretical DSP performance with low-latency deterministic interrupt response under 5 cycles. Typical applications include high-precision field-oriented motor control (PMSM, BLDC, ACIM), digital switched-mode power supplies with adaptive loop control, functional-safety automotive subsystems (chassis, EPS, braking), and industrial servo drives. The combination of dual cores and high-resolution PWM makes the part particularly well suited to time-critical feedback loops in both automotive (AEC-Q100) and industrial automation designs. When designing with this DSC, allocate DSP code to the slave core and the control plane to the master to fully exploit dual-core throughput. Decouple the 3.3V supply with low-ESR ceramic capacitors and connect the exposed pad (EP) to a continuous ground plane to meet the 1.5W power dissipation envelope. This page synthesizes distributor pricing, same-brand drop-in alternates, and practical design notes not found in the manufacturer datasheet.

見積もり お問い合わせ
DSPIC33CH256MP205-E/PT - Dual-Core 200MHz DSC, 256KB Flash | Microchip
DSPIC33CH256MP205-E/PT

DSPIC33CH256MP205-E/PT - Dual-Core 200MHz DSC, 256KB Flash | Microchip

The Microchip Technology DSPIC33CH256MP205-E/PT is a dual-core 16-bit Digital Signal Controller (DSC) that pairs a 100 MHz master dsPIC core with a 100 MHz slave dsPIC core in a single 48-pin TQFP package, delivering up to 200 MIPS combined DSP throughput for high-performance motor control, digital power conversion, and precision sensing applications. The device integrates 256 KB of program Flash memory, 32 KB of RAM on the master core, 24 KB of program Flash and 4 KB of RAM on the slave core, and is AEC-Q100 qualified for automotive deployment. It operates across a 3.0 V to 3.6 V supply range with 200 MHz maximum CPU clock speed on the master and 100 MHz on the slave, supporting industrial temperature grades of -40C to +125C. A Digital Signal Controller (DSC) is a microcontroller architecture that combines a 16-bit modified Harvard RISC CPU with a DSP engine, single-cycle MAC instructions, and dedicated motor-control peripherals. In the broader semiconductor taxonomy, a DSC sits between a generic microcontroller (MCU) and a full DSP - it offers deterministic interrupt latency, on-chip op-amps, comparators, high-resolution PWM, and encoder interfaces that pure microcontrollers lack, while providing more application integration than a standalone DSP. The dsPIC33CH family extends this concept with two cores in one die: the master runs the control loop and application code, while the slave handles time-critical sub-tasks such as closed-loop current sampling, allowing latency-critical work to be offloaded without disturbing the main loop. Key differentiating features include 8 high-resolution PWM channels with 250 ps resolution, 4 op-amps, 3 comparators with 32 ns response time, a 12-bit ADC at 3.5 Msps with 25 channels, 2 CAN FD controllers, 2 I2C, 3 SPI, 4 UART, and a Peripheral Trigger Generator for hardware event sequencing. The integrated charge time measurement unit (CTMU) supports capacitive touch sensing, and the configurable logic cell (CLC) replaces small external glue logic. Hardware safety features include a CRC engine, windowed watchdog timer, deadman timer, and lockable configuration bits, while Functional Safety (FuSa) documentation assists ISO 26262 system-level design. Typical applications span automotive mechatronic ECUs (Brushed, PMSM, and BLDC motor controllers), on-board chargers, industrial servo drives, intelligent power modules, multi-channel LED drivers, and medical analytical instruments. The 200 MHz maximum dual-core throughput supports Field-Oriented Control (FOC) loops on dual motors or cascaded power-conversion stages with cycle times well under 1 us. With the slave core absorbing housekeeping tasks such as debouncing, communication framing, or sensor diagnostics, system BOM is reduced and software modularity is improved. When designing with the DSPIC33CH256MP205-E/PT, take care to assign slave-core code to the dedicated slave bootloader region and use the master-to-slave mailbox register set for inter-core communication rather than shared globals. Decoupling the 3.3 V rail with at least one 100 nF X7R ceramic per VDD pin and a 10 uF bulk capacitor is mandatory for switching-noise immunity; the high-resolution PWM edge placement is sensitive to supply ripple.

見積もり お問い合わせ
DSPIC33CH256MP205-I/PT - Dual-Core 16-bit DSC 256KB Flash TQFP-48 | Microchip
DSPIC33CH256MP205-I/PT

DSPIC33CH256MP205-I/PT - Dual-Core 16-bit DSC 256KB Flash TQFP-48 | Microchip

The Microchip DSPIC33CH256MP205-I/PT is a dual-core 16-bit digital signal controller (DSC) from the dsPIC33CH family, integrating a 100 MIPS master core and a 90 MIPS slave core on a single die. It ships with 256 KB of Flash memory and 32 KB of RAM, packaged in a 48-pin TQFP (7x7 mm) surface-mount footprint and operates from a 3.0V to 3.6V supply. The dual-core architecture lets one core execute real-time motor-control and DSP loops while the other handles communication stacks, housekeeping, or custom logic, removing the need for an external companion MCU. A DSC (digital signal controller) is a hybrid device that combines a microcontroller's deterministic peripheral set with a DSP engine's MAC unit and SIMD instructions. In the taxonomy of microelectronics, a DSC sits between a microcontroller (MCU) and a digital signal processor (DSP), inheriting DSP-grade multiply-accumulate throughput while retaining on-chip ADCs, PWMs, and communication peripherals. This positions the dsPIC33CH family as a power management and motor-control optimized MCU/DSP hybrid for high-end embedded designs. Key specifications include 200 MHz maximum CPU clock on the master (180 MHz on the slave), 8 DMA channels for low-overhead data movement, 5 general-purpose timers, dual 16-bit high-resolution PWM generators with 250 ps resolution, CAN FD peripheral, integrated op-amps and comparators for current sensing, and a 12-bit ADC with up to 3.5 MSPS sampling. Functional-safety hardware (ISO 26262-ready features) and live-update Flash support round out the integrated peripherals, enabling closed-loop FOC motor control, digital power conversion, and wireless charging at high switching frequencies. Architecturally the device pairs a 16-bit dsPIC core with single-cycle MAC, a barrel shifter, and a 40-bit accumulator, achieving 100 MIPS sustained throughput at 200 MHz. The slave core exposes its own peripherals and program memory, allowing designers to partition firmware into real-time and non-real-time domains for improved isolation and certification paths. Hardware interlocks between cores and shared peripheral semaphores simplify inter-core messaging without software arbitration overhead. Typical applications include field-oriented control (FOC) of PMSM/BLDC motors for industrial drives, on-board EV chargers and DC/DC converters using digital control loops, fan and pump control, server and telecom switched-mode power supplies (SMPS), digital illumination, and functional-safety robotics where two independent compute domains are required. The wide operating temperature range of -40C to +85C (industrial) suits outdoor and factory-floor deployments. When designing with this DSC, allocate separate linker sections for the master and slave images, plan inter-core FIFOs and shared RAM carefully, and provide adequate bulk decoupling close to the AVDD/VDD pins to keep switching noise away from the analog front end. Compared with a single-core MCU plus external DSP coprocessor, the integrated dual-core topology reduces PCB area, lowers BOM cost, and shortens BOM risk on multi-source motor-control designs. This page synthesizes distributor pricing, dual-core peripheral trade-offs, and drop-in same-package alternatives that are not aggregated in the manufacturer datasheet, including pin-to-pin variants for memory size and temperature grade.

見積もり お問い合わせ
DSPIC33CH256MP205T-I/PT - Dual-Core 16-bit DSC, 256KB Flash | Microchip
DSPIC33CH256MP205T-I/PT

DSPIC33CH256MP205T-I/PT - Dual-Core 16-bit DSC, 256KB Flash | Microchip

The Microchip Technology DSPIC33CH256MP205T-I/PT is a dual-core 16-bit Digital Signal Controller (DSC) in the dsPIC33CH family, pairing a 100 MIPS main core with a 200 MHz slave core for high-performance, deterministic motor control. The device integrates 256 KB of Flash program memory and 32 KB of general-purpose SRAM, plus 16 KB of dedicated slave-core RAM, all in a 48-pin TQFP (PT) surface-mount package measuring 7x7 mm. A Digital Signal Controller (DSC) is a hybrid microcontroller that combines the deterministic interrupt response of an MCU with the high-throughput math capability of a DSP. As part of the broader 16-bit DSC -> microcontroller -> embedded controller -> semiconductor taxonomy, the dsPIC33CH family targets safety-critical real-time control, where a dedicated slave core can execute time-critical control loops while the main core runs communication stacks, user interfaces, and housekeeping. Key features include dual 16-bit dsPIC DSC cores, four 16-bit high-resolution PWM channels with 1 ns resolution for precision motor drives, integrated CAN FD peripheral, six UART, two SPI, and two I2C interfaces, plus a 12-bit ADC with up to 24 channels. The integrated peripherals also include six 16-bit timers, eight DMA channels, and a Peripheral Trigger Generator (PTG) for hardware state machines. Functional-safety features such as a Windowed Watchdog Timer (WWDT), Deadman Timer (DMT), and lockable configuration make the device suitable for ASIL-B/SIL-2 capable systems. Architecturally, the main and slave cores communicate through dedicated shared-memory regions and a hardware mailbox, allowing the slave to be deployed as a tightly coupled control coprocessor. The device supports motor-control profiles including Field-Oriented Control (FOC) of PMSM/BLDC motors, peak-current-mode power conversion, and digital PFC, all of which benefit from the 1 ns PWM edge placement and dual-core determinism. Typical applications include high-performance BLDC/PMSM motor drives, field-oriented control servo drives, automotive sensor interfaces, and digital switched-mode power supplies. Compared with a single-core DSC, the dedicated slave core offloads the control loop to remove software jitter and free main-core bandwidth for diagnostics and connectivity. Designers should budget for a robust 3.3 V decoupling network (10 uF + 100 nF near VDD) and, when used in motor-drive hardware, ensure the PWM-to-FET gate-drive timing budget accounts for the 1 ns high-resolution edge placement. The slave-core code is loaded via the main core at boot, so inter-core handshaking must be validated against the published mailbox protocol. This page consolidates Microchip datasheet parameters, XAIPART distributor pricing, drop-in alternative cross-references, and practical design guidance not available on the manufacturer datasheet alone.

見積もり お問い合わせ
DSPIC33CH256MP206-E/MR - Dual-Core 200MHz DSC, 328KB Flash | Microchip
DSPIC33CH256MP206-E/MR

DSPIC33CH256MP206-E/MR - Dual-Core 200MHz DSC, 328KB Flash | Microchip

The Microchip Technology DSPIC33CH256MP206-E/MR is a high-performance dual-core 16-bit Digital Signal Controller (DSC) that pairs a 200 MHz main core and a 200 MHz slave core, delivering up to 100 MIPS per core in a 64-pin QFN (9x9 mm) package with exposed thermal pad. The device integrates 328 kB of Flash program memory (PRAM) and 64 kB of RAM, making it suitable for functional-safety and high-end motor control applications. A Digital Signal Controller (DSC) is a class of microcontroller that fuses a microcontroller's deterministic I/O and interrupt handling with a digital signal processor's (DSP) single-cycle MAC, barrel shifter, and saturating arithmetic. The dsPIC33CH family extends the DSC concept with a true dual-core architecture where the slave core executes time-critical control loops while the main core handles communication, housekeeping, and application logic. This hierarchy—DSC under microcontroller, both under embedded processor—maps cleanly into the broader taxonomy of microcontrollers and DSPs. Key features include 328 kB Flash, 64 kB RAM, dual dsPIC DSC cores running at 180 MHz (main) and 200 MHz (slave), 100 MIPS per core DSP throughput, a high-resolution PWM module suited to precision motor drives, and on-chip functional-safety diagnostics (FuSa). The 64-QFN exposed-pad package provides low thermal resistance and a compact 9x9 mm footprint ideal for space-constrained motor-control PCBs. Typical applications include field-oriented control (FOC) of PMSM/BLDC motors, digital power conversion, automotive sensor-fusion, and functional-safety systems up to ASIL-B. The dual-core partitioning lets the slave handle the current-control loop at microsecond intervals while the main core services CAN-FD, run diagnostics, and updates the user interface. When designing, allocate the slave-core's tightly bounded cycles for the torque loop, and keep the main core's bus bandwidth above 50 percent during housekeeping to avoid stalls. Note the -E suffix designates the -40C to +125C automotive temperature grade; the -I suffix variant is industrial -40C to +85C. This page combines verified distributor pricing, package-level drop-in alternatives, and practical dual-core firmware notes that go beyond the manufacturer datasheet, giving procurement and engineering teams one place to evaluate the DSPIC33CH256MP206-E/MR.

見積もり お問い合わせ
DSPIC33CH256MP206-E/PT - Dual-Core 16-bit DSC, 256KB Flash | Microchip
DSPIC33CH256MP206-E/PT

DSPIC33CH256MP206-E/PT - Dual-Core 16-bit DSC, 256KB Flash | Microchip

The Microchip DSPIC33CH256MP206-E/PT is a 16-bit dual-core digital signal controller (DSC) from the dsPIC33CH family, featuring a primary core running up to 200 MHz and a slave core at 180 MHz with 328 KB of Flash program memory, housed in a 64-pin TQFP (10x10 mm) package. The device integrates a DSP engine, 64 KB of RAM (32 KB + 16 KB dedicated slave core RAM), and AEC-Q100 qualification for automotive functional-safety applications. A digital signal controller (DSC) is a hybrid architecture combining a microcontroller (MCU) with a digital signal processor (DSP) on a single die. DSCs occupy the middle ground between general-purpose MCUs and dedicated DSPs, providing deterministic real-time control plus high-throughput signal processing. Within the Microchip taxonomy, the dsPIC33CH family sits at the top of the dsPIC33 line, using the dual-core topology to separate time-critical control loops (on the slave core) from communication and supervisory tasks (on the primary core), which simplifies software partitioning for functional-safety (FuSa) designs. Key features of the DSPIC33CH256MP206 include up to 53 user I/O pins, twelve 16-bit PWM channels with 250 ps resolution for precision motor control, twelve 12-bit ADC modules with up to 34 input channels at 3.5 Msps, four 12-bit DAC channels, multiple UART/SPI/I2C interfaces, and CAN-FD support. The on-chip DSP engine accelerates math operations via single-cycle MAC instructions, enabling closed-loop control rates well above 1 MHz without CPU offload. The dual-core design allows the slave core to handle latency-critical tasks such as field-oriented control (FOC) commutation loops in motor drives, while the primary core runs the state machine, communication stacks, and diagnostics. The device supports 3.0 V to 3.6 V single-supply operation, internal oscillator with PLL, and the full -40 C to +125 C automotive temperature range (E-temp). Functional-safety hardware (dual watchdog, ECC on Flash, memory BIST) eases ISO 26262 and IEC 61508 certification paths. Typical applications include high-performance brushless DC (BLDC) and permanent-magnet synchronous motor (PMSM) drives, on-board EV chargers, automotive LED matrix drivers, digital power conversion (totem-pole PFC, LLC), and industrial servo drives. The combination of dual-core partitioning and dedicated motor-control peripherals makes this part a strong fit for ASIL-B/C designs where a single-core MCU cannot meet the loop-rate and diagnostic-coverage targets simultaneously. When designing with this DSC, allocate GPIO and peripheral channels early because the 64-pin TQFP has fewer pins than the 80-pin TQFP variant in the same family. The dual cores must be programmed with separate firmware images - the slave core boots first from a PRAM region configured by the master, so linker-script and boot-loader design requires attention. This page synthesizes distributor pricing, drop-in Microchip alternates, AEC-Q100 notes, and dual-core firmware-design guidance that goes beyond the manufacturer datasheet summary.

見積もり お問い合わせ
DSPIC33CH256MP206-I/MR - 100MHz Dual-Core 16-bit DSC | Microchip
DSPIC33CH256MP206-I/MR

DSPIC33CH256MP206-I/MR - 100MHz Dual-Core 16-bit DSC | Microchip

The Microchip DSPIC33CH256MP206-I/MR is a dual-core 16-bit Digital Signal Controller (DSC) featuring a 100 MIPS main core and a 90 MIPS slave core, housed in a 64-pin QFN (9x9 mm) package with exposed pad. It integrates 256 KB of Flash program memory, 32 KB of SRAM, and a comprehensive DSP engine optimized for high-performance precision motor control and digital power conversion. A Digital Signal Controller is a hybrid device that combines the deterministic interrupt response and peripheral integration of a microcontroller with the computational throughput of a DSP engine. The dsPIC33CH family in particular is a dual-core architecture where one core (the slave) is dedicated to time-critical control loops while the other (the master) handles communication, housekeeping, and application logic. This architecture falls within the broader category of microcontrollers -> 16-bit MCUs -> DSC -> motor-control & power-conversion ICs. Key features of the DSPIC33CH256MP206 include dual 16-bit dsPIC DSC cores, integrated high-speed analog peripherals including 3 MSPS ADCs with up to 24 channels, multiple PWM channels with 250 ps resolution for fine-grained motor and power-conversion control, and dedicated CAN-FD and high-speed UART/SPI/I2C interfaces. The device operates from a 3.0 V to 3.6 V supply and is qualified for the industrial -40C to +85C temperature range. The dual-core partitioning enables latency-critical tasks such as field-oriented control (FOC) loops and digital PFC to run on the slave core at full 90 MIPS without interrupt jitter from the master core. The on-chip PRAM (peripheral RAM) shared between cores reduces inter-core communication latency compared with external mailbox implementations. This makes the DSPIC33CH family well suited to multi-loop motor drives and bridgeless totem-pole PFC converters where deterministic loop timing is essential. Typical applications include high-efficiency field-oriented control (FOC) motor drives, digital switch-mode power supplies including totem-pole PFC and LLC converters, automotive sensor fusion, industrial servo control, and digital lighting ballast control. The wide peripheral integration also makes it suitable for functional-safety implementations where a dedicated slave core can run safety diagnostics in parallel. When designing with this part, allocate Flash carefully: 256 KB is shared between both cores plus a system partition region. Use MPLAB X IDE with the dsPIC33CH plug-in for code generation and the XC-DSC compiler for DSP-aware optimization. The 9x9 mm QFN package requires thermal vias under the exposed pad to meet the datasheet's thermal resistance of approximately 23 C/W on a 4-layer JEDEC test board.

見積もり お問い合わせ
DSPIC33CH256MP206-I/PT - Dual-Core 100MHz DSC, 256KB Flash | Microchip
DSPIC33CH256MP206-I/PT

DSPIC33CH256MP206-I/PT - Dual-Core 100MHz DSC, 256KB Flash | Microchip

The Microchip DSPIC33CH256MP206-I/PT is a dual-core 16-bit Digital Signal Controller (DSC) that pairs a 90 MIPS main core with a 100 MIPS slave core on a single die, delivered in a 64-pin TQFP (PT) package. The device integrates 256 KB of Flash program memory plus 32 KB of auxiliary Flash for the slave core, 32 KB SRAM, and Microchip's dsPIC33C enhanced DSP engine with single-cycle MAC and dual 40-bit accumulators. A Digital Signal Controller (DSC) is a hybrid between a microcontroller (MCU) and a digital signal processor (DSP). It combines deterministic interrupt-driven control loops (typical of MCUs) with deterministic DSP throughput (typical of DSPs), making it well suited to applications such as field-oriented motor control (FOC), digital power conversion, and audio processing where both real-time control and high-rate signal math are required. Within Microchip's portfolio, DSCs sit between PIC MCUs and standalone dsPIC DSPs and target high-performance embedded control. Key features of the DSPIC33CH256MP206 include integrated functional-safety support for ISO 26262 and IEC 61508 designs, 8 KB shared PRAM between the two cores, up to 200 MHz PWM with high-resolution duty cycle and edge placement, dual 12-bit ADCs at up to 3.5 Msps with up to 24 channels, and high-speed comparators and op-amps for current sensing. The dual-core architecture enables partitioning of time-critical control (slave) from application and communication code (master), reducing jitter and easing firmware certification for safety-critical systems. The dsPIC33CH architecture uses a 16-bit Harvard bus with DSP extensions, separate instruction and data paths, and a tightly coupled DSP engine. The slave core's 100 MIPS and the master core's 90 MIPS performance support 32 kHz to 50 MHz FOC loops and Class-D audio amplification at >100 kHz switching frequencies, while peripheral triggers and DMA minimize CPU overhead and provide deterministic ISR latency. Typical applications include high-performance motor control (BLDC, PMSM, ACIM, SRM), digital power supplies (PFC, LLC, full-bridge), renewable-energy inverters, automotive sensor fusion, Class-D audio amplifiers, and functional-safety industrial drives. The integrated op-amps and comparators remove external analog front-end components. When laying out the board, dedicate a low-impedance ground return for the analog and power sections, keep the VCAP pin within 1 cm of its decoupling capacitor, and follow the recommended PCB layout in the family reference manual to meet the ADC SNR and PWM timing margins. This page synthesizes distributor pricing, dual-core drop-in alternatives, and practical dual-core design notes beyond what is found in the standalone dsPIC33CH family datasheet.

見積もり お問い合わせ
DSPIC33CH256MP208-E/PT - Dual-Core 100MHz 256KB DSC | Microchip
DSPIC33CH256MP208-E/PT

DSPIC33CH256MP208-E/PT - Dual-Core 100MHz 256KB DSC | Microchip

The Microchip DSPIC33CH256MP208-E/PT is a dual-core 16-bit Digital Signal Controller (DSC) combining a 90 MIPS master core and a 100 MIPS slave core in a single 80-pin TQFP (12x12 mm) package, qualified to the -40C to +125C extended (E) temperature range. The device integrates 328 KB of dual-partition Flash, 32 KB + 16 KB of RAM across the two cores, and high-resolution PWM with CAN Flexible Data-Rate (CAN FD) support for advanced digital power, motor control, and functional-safety (FuSa) applications. What is a digital signal controller? A DSC is a hybrid architecture that combines the deterministic interrupt response and peripheral set of a microcontroller (MCU) with the multiply-accumulate (MAC) throughput of a digital signal processor (DSP). Within the broader taxonomy, the dsPIC33CH sits at the apex of the dsPIC33 family, supporting asymmetric dual-core operation where the slave core offloads time-critical control loops (digital power, field-oriented motor control) while the master core runs the application stack, communications, and housekeeping. This dual-core partitioning is unique in the DSC market and targets ISO 26262 ASIL-B and IEC 61508 SIL-2 functional-safety designs. Key specifications include 180/200 MHz maximum operating frequency across the two cores (90/100 MIPS instruction throughput), 12-bit ADC with up to 3.5 MSps, configurable logic cells, 8-channel high-resolution PWM with 250 ps resolution, and on-chip op-amps and comparators for analog signal conditioning. The device also features a crypto engine, secure boot, and immutable root-of-trust for connected industrial applications. The dsPIC33CH architecture uses a Harvard bus with independent X and Y data paths feeding a single-cycle MAC engine on each core, allowing closed-loop control periods below 1 us. Hardware support for field-oriented control (FOC) of PMSM, BLDC, and ACIM motors is provided through the integrated PWM, ADC, and quadrature encoder interface, eliminating the need for an external FPGA or ASIC in many motor drives. Typical applications include digital switch-mode power supplies (PFC + LLC or totem-pole), high-performance motor control (FOC for servo drives, e-bikes, drones, appliances), wireless charging transmitters, and functional-safety industrial controllers. The dual-core topology maps cleanly onto safety architectures where one core performs the safety diagnostic self-test while the other runs the application. When designing with this device, allocate the slave core to deterministic tasks (control loops, ADC sampling, PWM update) and reserve the master core for communications and application logic. Use the MPLAB XC-DSC compiler with the dsPIC33CH-specific libraries and connect via MPLAB ICD 4 or MPLAB PICkit 5 for programming/debug. The 80-pin TQFP footprint simplifies prototype hand-soldering compared to the 64-pin and 48-pin variants in the same family. This page synthesizes distributor pricing, drop-in same-package alternatives, and practical design notes not found in the manufacturer datasheet, giving engineers a single-page comparison resource for sourcing and second-source decisions.

見積もり お問い合わせ
DSPIC33CH256MP208-I/PT - Dual-Core 100MHz DSC, 256KB Flash | Microchip
DSPIC33CH256MP208-I/PT

DSPIC33CH256MP208-I/PT - Dual-Core 100MHz DSC, 256KB Flash | Microchip

The Microchip Technology DSPIC33CH256MP208-I/PT is a dual-core 16-bit Digital Signal Controller (DSC) that combines a 100 MIPS main core with a dedicated 100 MIPS slave core in a single 80-pin TQFP (PT) package. The device integrates 256 KB of Flash program memory, 32 KB of data RAM on the master side plus 16 KB on the slave core, and runs at up to 200 MHz (180 MHz for the master/slave pair) with integrated DSP and enhanced on-chip peripherals including high-resolution PWM and CAN Flexible Data-Rate (CAN FD). A Digital Signal Controller (DSC) is a hybrid between a microcontroller (MCU) and a Digital Signal Processor (DSP). The dsPIC33CH architecture is positioned within the broader Microchip taxonomy as: DSC -> Digital Signal Controller -> Microcontroller -> Embedded Processor -> Semiconductor. Unlike a pure MCU, the dsPIC33CH executes single-cycle MAC instructions and integrates DSP features directly into the core, eliminating the need for a separate DSP chip. The dual-core topology allows designers to run real-time control loops on the slave core while the master core handles communication, system management, or higher-level state machines. Key differentiating features include dual independent cores with isolated peripherals, high-resolution PWM (250 ps resolution) for precision motor control, four DAC outputs, twelve 16-bit ADC channels with up to 3.25 MSPS conversion rate, four analog comparators, and integrated op-amps. Functional Safety (FuSa) features and CAN FD support target automotive and industrial safety-critical applications. The device operates from a 3.0V to 3.6V supply and supports an industrial temperature range of -40C to +85C. The architecture uses a 24-bit instruction word with a 16-bit data path, allowing C-compiler-friendly code density while maintaining DSP throughput. The slave core can execute control algorithms (such as field-oriented control loops for motors) with deterministic timing independent of the master core's interrupt load. This isolation is critical for high-bandwidth digital power conversion and sensorless motor control. Typical applications include high-performance precision motor control (PMSM, BLDC, AC induction), digital power conversion (PFC, LLC, full-bridge converters), automotive sensor fusion, industrial automation drives, and functional safety systems. The high-resolution PWM and dual-core architecture make it particularly suitable for sensorless FOC motor control at switching frequencies above 100 kHz. When designing with this device, allocate adequate PCB area for thermal dissipation: although the TQFP-80 package typically dissipates less than 1W in motor-control use cases, the dual-core operation can push junction temperatures higher. Use Microchip's MPLAB X IDE with the dsPIC33CH plug-in for code development and the dsPIC33CH Motor Control Library for FOC reference firmware. This page synthesizes distributor pricing, dual-core architectural analysis, and pin-compatible alternatives for the DSPIC33CH256MP208-I/PT that are not available on individual distributor pages, enabling direct cross-shopping for engineers and procurement teams.

見積もり お問い合わせ
DSPIC33CH256MP208T-I/PT - Dual-Core 100MHz DSC, 256KB Flash | Microchip
DSPIC33CH256MP208T-I/PT

DSPIC33CH256MP208T-I/PT - Dual-Core 100MHz DSC, 256KB Flash | Microchip

The Microchip DSPIC33CH256MP208T-I/PT is a dual-core 16-bit Digital Signal Controller (DSC) operating at up to 100 MIPS, integrating 256 KB of Flash memory and packaged in an 80-pin TQFP (12x12 mm). It belongs to the dsPIC33CH family, which combines a high-performance main core and a dedicated slave core on a single die, enabling deterministic real-time control with offloaded housekeeping tasks. The device targets high-performance, precision motor control, digital power conversion, and advanced sensing applications. A Digital Signal Controller (DSC) is a hybrid device that merges the interrupt-driven deterministic behavior of a microcontroller with the throughput and computational capability of a Digital Signal Processor (DSP). DSCs occupy the middle tier of the embedded-compute hierarchy between standard microcontrollers (MCU) and full DSPs, and they belong to the broader class of microcontrollers and embedded processors. The dsPIC33CH family's dual-core architecture extends this category by allowing partitioned firmware: the main core executes time-critical control loops while the slave core handles communications, housekeeping, or safety diagnostics. Key features include a 100 MIPS main core paired with a 100 MIPS slave core, 256 KB of on-chip Flash program memory, configurable 16 KB + 32 KB RAM partitions, a high-resolution PWM module suited for digital power and motor control, CAN FD support, multiple UART/SPI/I2C interfaces, and a 12-bit ADC with up to 3.5 MSPS conversion rate. The -I temperature grade specifies an industrial operating range of -40C to +85C. The 80-pin TQFP footprint simplifies PCB layout by providing generous pin spacing (0.5 mm pitch) versus dense QFN or BGA alternatives. The dual-core design enables hardware-based functional safety partitioning, deterministic task scheduling, and parallel algorithm execution that would otherwise require a separate companion MCU. Integrated peripherals such as the Configurable Logic Cell (CLC) and Peripheral Trigger Generator (PTG) allow glue logic to be implemented on-chip, reducing BOM cost and board area. The device is AEC-Q100 qualified in related variants, supporting automotive deployment. Typical applications include field-oriented control (FOC) of PMSM and BLDC motors, on-board EV charging, digital LLC and PFC converters, photovoltaic inverters, and high-density industrial SMPS designs. The slave core can offload housekeeping such as housekeeping communication stacks or peripheral management. Design considerations: 80-pin TQFP packages have higher thermal resistance than QFN equivalents - a copper pour beneath the package is recommended. Verify dual-core memory allocation in MPLAB X IDE before firmware development; the slave core requires a separate firmware image loaded into PRAM. Always consult the manufacturer datasheet for the latest pinout, errata, and electrical characteristics. This page synthesizes distributor pricing, drop-in same-package alternatives within the dsPIC33CH family, and practical design notes not found in the manufacturer datasheet.

見積もり お問い合わせ
DSPIC33CH256MP505-E/M4 - Dual-Core 100MHz DSC, 256KB Flash | Microchip
DSPIC33CH256MP505-E/M4

DSPIC33CH256MP505-E/M4 - Dual-Core 100MHz DSC, 256KB Flash | Microchip

The Microchip DSPIC33CH256MP505-E/M4 is a dual-core 16-bit Digital Signal Controller (DSC) from the dsPIC33CH family, integrating a 100 MIPS main core and a 90 MIPS slave core in a 48-pin UQFN (6x6) package. The device combines 256 KB of Flash program memory with 32 KB RAM on the main core plus an additional 16 KB of slave-core PRAM, enabling partitioned real-time control where one core handles high-speed DSP tasks while the other manages housekeeping and communication. It operates from 3.0V to 3.6V and supports functional-safety (FuSa) capable design workflows for safety-critical embedded applications. Key features include dual dsPIC DSC cores with integrated DSP engine, high-resolution PWM (HRPWM) with 250 ps resolution, CAN-FD support, and up to 200 MHz maximum core operating frequency. The device integrates multiple analog peripherals (12-bit ADC, comparators, DAC), motor-control PWMs, and communication interfaces including SPI, I2C, UART, and CAN-FD. The main/slave inter-core communication uses shared SRAM mailbox regions, eliminating external handshake glue logic. Technically, the dsPIC33CH architecture uses a Harvard-style bus with single-cycle MAC, hardware DO/REP loops, and zero-overhead looping, allowing deterministic execution of field-oriented control (FOC) algorithms within tight PWM cycle windows. The 100 MIPS main core can execute a complete FOC routine in under 5 microseconds, supporting field weakening, MTPA, and sensorless observer algorithms for high-speed PMSM and BLDC drives. Typical applications include high-performance motor control (PMSM, BLDC, AC induction, switched reluctance), digital power conversion (PFC, LLC, full-bridge, synchronous rectification), automotive sensor fusion, and functional-safety drives up to ASIL-B/SIL-2. The dual-core split lets the main core run the time-critical control loop while the slave core manages comms, housekeeping, or diagnostics. When designing with this device, plan pin allocation carefully - the 48-pin UQFN limits available I/O. The slave core has its own dedicated PGED/S1MCLRx programming/debug pins which may require pull-ups for reliable ICSP access. Use MPLAB XC-DSC compiler for both cores and configure inter-core mailboxes via SFRs. This page combines distributor pricing, pin-compatible dsPIC33CH family variants, and practical design notes not found in the datasheet alone.

見積もり お問い合わせ
DSPIC33CH256MP505-I/PT - 256KB Flash Dual-Core 100MHz DSC | Microchip
DSPIC33CH256MP505-I/PT

DSPIC33CH256MP505-I/PT - 256KB Flash Dual-Core 100MHz DSC | Microchip

The Microchip DSPIC33CH256MP505-I/PT is a dual-core 16-bit Digital Signal Controller (DSC) in a 48-pin TQFP (7x7) package, integrating a high-performance 100 MIPS main dsPIC33C core alongside a 90 MIPS secondary dsPIC33C core on a single die. The device provides 256 KB of Flash program memory, 16 KB of SRAM on the main core, and 4 KB of dedicated data RAM on the slave core, enabling deterministic parallel control and DSP tasks. Maximum operating frequency reaches 100 MHz with an extended temperature range of -40C to +85C and supply voltage of 3.0V to 3.6V. A Digital Signal Controller (DSC) is a microcontroller architecture that combines a standard MCU control pipeline with a Digital Signal Processor (DSP) engine for high-speed arithmetic. Within the broader taxonomy, DSCs sit between microcontrollers (MCU) and microcontrollers-with-DSP, themselves a subcategory of 16-bit embedded controllers and ultimately embedded processors in the integrated circuits hierarchy. The dsPIC33CH family specifically targets motor control, digital power conversion, and safety-critical applications where deterministic closed-loop performance is mandatory. Key features include dual independent dsPIC cores, high-resolution PWM with 1 ns edge placement, integrated CAN Flexible Data-Rate (CAN FD), 12-bit ADC up to 3.5 Msps, multiple UART/SPI/I2C interfaces, and Functional Safety (FuSa) support for ASIL-B/SIL-2 applications. The slave core can execute user code independently, allowing the main core to focus on real-time DSP tasks while the slave handles housekeeping, communication stacks, or sensor sampling. The 48-pin TQFP (PT) package offers an industry-standard 7x7 mm footprint with 0.5 mm pitch, well-suited for hand-solderable prototyping and volume production. AEC-Q100 qualification is available on automotive-grade variants, and the device supports debug via standard ICSP/ICD interfaces for both cores simultaneously. Typical applications include field-oriented control (FOC) motor drives, digital totem-pole PFC power supplies, wireless battery management systems, servo drives, and functional safety PLCs. When designing, allocate pin mapping carefully between cores and consult the dual-core programming model documentation for inter-core mailbox and shared RAM usage.

見積もり お問い合わせ
DSPIC33CH256MP505T-I/PT - Dual-Core 100MHz DSC, 256KB Flash | Microchip
DSPIC33CH256MP505T-I/PT

DSPIC33CH256MP505T-I/PT - Dual-Core 100MHz DSC, 256KB Flash | Microchip

The Microchip Technology DSPIC33CH256MP505T-I/PT is a high-performance 16-bit dual-core Digital Signal Controller (DSC) from the dsPIC33CH family, integrating 328KB of Flash and 32KB+16KB RAM in a 48-pin TQFP (7x7) package. The device combines a 100 MIPS master dsPIC33 core with a 90 MIPS slave core, both capable of executing DSP and control workloads at up to 200 MHz peripheral clock. What is a Digital Signal Controller (DSC)? A DSC is a hybrid microcontroller/DSP that combines a deterministic 16-bit MCU core with single-cycle DSP MAC hardware, enabling tight feedback loops for motor control, digital power, and advanced sensing. The dsPIC33CH family specifically uses a dual-core architecture: a high-performance master core for control and communication tasks, and a dedicated slave core for time-critical DSP operations such as sensorless motor commutation. Within the broader semiconductor taxonomy, the part sits at: DSC -> Digital Signal Controller -> Microcontroller -> Integrated Circuit -> Semiconductor. Key features include dual 16-bit dsPIC DSC cores (master at 100 MIPS, slave at 90 MIPS), 256KB program Flash (328KB total program/data), 32KB SRAM on master plus 16KB on slave, and an integrated high-resolution PWM module (250 ps resolution). The part also integrates CAN-FD, multiple UART/SPI/I2C peripherals, a 12-bit ADC with up to 3.5 MSPS, and supports Functional Safety (FuSa) features such as lock-step diagnostics and RAM BIST. Architecturally, the dual-core design allows independent firmware on each core, with shared peripherals arbitrated via an internal bus matrix. The slave core can run sensorless Field-Oriented Control (FOC) algorithms for a permanent-magnet motor while the master core runs the user interface and communication stack, dramatically reducing latency and jitter versus single-core architectures. Typical applications include high-performance field-oriented motor control (PMSM, BLDC, ACIM), digital power conversion (bridgeless PFC, LLC, phase-shifted full-bridge), advanced LED lighting drivers, and Functional Safety systems up to ASIL-B / SIL-2. The wide 3.0V-3.6V operating range and 48-pin compact TQFP footprint target cost-sensitive industrial embedded designs. When designing with this device, ensure that the master/slave inter-core communication via mailbox FIFOs is properly sized for your loop period - the slave core typically receives one or more PWM-cycle measurement buffers from the master and returns updated duty-cycle commands. Decoupling requires a 10uF bulk plus 100nF per VDD/AVDD pair, and traces to the high-resolution PWM outputs must be length-matched for sub-nanosecond skew. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found on the manufacturer datasheet to help engineers evaluate the DSPIC33CH256MP505T-I/PT for next-generation motor control and digital power platforms.

見積もり お問い合わせ
DSPIC33CH256MP506-E/MR - Dual-Core 16-bit DSC, 256KB Flash | Microchip
DSPIC33CH256MP506-E/MR

DSPIC33CH256MP506-E/MR - Dual-Core 16-bit DSC, 256KB Flash | Microchip

The Microchip DSPIC33CH256MP506-E/MR is a dual-core 16-bit Digital Signal Controller (DSC) in the dsPIC33CH family, delivering 200 MIPS combined performance from a master core (100 MIPS) and slave core (90 MIPS) that share a 64-pin QFN (9x9 mm) package. The device integrates 256 KB of Flash program memory plus 32 KB of SRAM on the master core and 16 KB of dedicated slave-core SRAM, with a 200 MHz internal oscillator derived from an external crystal or system clock. A digital signal controller is a microcontroller architecture that combines a deterministic 16-bit MCU pipeline with single-cycle hardware MAC (multiply-accumulate) and DSP engines, allowing real-time control loops and signal-processing kernels to coexist on one chip. Within the broader taxonomy it sits between general-purpose microcontrollers (MCU) and full digital signal processors (DSP), and dsPIC33CH parts extend that into the dual-core domain where one core can run a motor-control loop while the other handles housekeeping or communication stacks. Key features include CAN FD, high-resolution PWM (typical for motor and digital power control), four DMA channels, multiple SPI/I2C/UART interfaces, and AEC-Q100 automotive qualification. The on-chip peripherals and dual-core partitioning enable developers to dedicate the slave core to time-critical PWM/CPU-bound tasks such as field-oriented control while the master runs communication, diagnostics, and the application stack. Architecturally, the two dsPIC cores operate independently yet interconnect via tightly-coupled mailbox registers and shared RAM, giving the design engineer predictable bandwidth without software arbitration. The 200 MHz max clock and single-cycle MAC make the device well-suited to high-switching-frequency digital power and advanced motor-control algorithms where instruction budget would otherwise starve an MCU. Typical applications include BLDC/PMSM motor drives, digital switch-mode power supplies, solar inverters, automotive sensor fusion, and industrial automation controllers. Industrial-grade -40C to +125C operating temperature and AEC-Q100 qualification extend use cases into chassis and under-hood environments. Designers should review the slave-core RAM partitioning (16 KB) early in firmware architecture planning, because mailbox and shared-memory layout between cores influences inter-core latency. Stack depth and interrupt priority also need separate configuration per core. This page consolidates distributor pricing, parametric drop-in alternatives, and engineering design notes that go beyond the manufacturer datasheet, so design teams can compare and qualify the DSPIC33CH256MP506-E/MR against competing dual-core DSCs without leaving the page.

見積もり お問い合わせ
DSPIC33CH256MP506-I/MR - Dual-Core DSC 256KB Flash | Microchip
DSPIC33CH256MP506-I/MR

DSPIC33CH256MP506-I/MR - Dual-Core DSC 256KB Flash | Microchip

The Microchip DSPIC33CH256MP506-I/MR is a high-performance 16-bit dual-core Digital Signal Controller (DSC) from the dsPIC33CH family with Functional Safety (FuSa) capability, integrating 328 kB of Flash program memory and 64 kB of RAM in a 64-pin QFN (9x9 mm) package. The primary core runs at 200 MHz (100 MIPS) while the secondary core runs at 180 MHz (90 MIPS), enabling partitioned real-time control with deterministic inter-core communication. The device operates from a 3.0 V to 3.6 V supply and integrates advanced peripherals including high-resolution PWM, multiple CAN FD controllers, I2S, SPI, I2C, and 12-bit ADCs. A Digital Signal Controller (DSC) combines a microcontroller's deterministic interrupt handling with a DSP's computational throughput for closed-loop control applications. In the dsPIC33CH family, Microchip pioneered a true dual-core architecture where the secondary (slave) core can offload time-critical DSP tasks (sensorless FOC, digital filtering, power conversion math) from the primary (master) core which runs the application state machine and communication stacks. This partitioning delivers higher system bandwidth than single-core DSCs at the same clock rate. Key features include dual dsPIC DSC cores with independent peripherals, hardware safety features for ISO 26262 functional safety integration, four 12-bit ADC modules with up to 3.5 MSPS sampling rate, dedicated High-Resolution PWM (250 ps resolution) for precision motor and digital power control, and CAN FD interfaces supporting automotive bit rates. The 64-pin QFN package (MR suffix) provides a compact 9x9 mm footprint suitable for space-constrained power-conversion and motor-drive designs. Typical applications span sensorless field-oriented control (FOC) of PMSM, BLDC, and AC induction motors, digital switch-mode power supplies (SMPS) with PFC, photovoltaic micro-inverters, automotive body and chassis ECUs, and industrial drives up to several kW. The dual-core architecture reduces firmware complexity in safety-critical designs by isolating diagnostic and supervision tasks on the secondary core. Designers should provide 100 nF decoupling at every VDD/VSS pair, route the two cores' PGECx/PGEDx programming pairs to a dedicated header, and verify the high-resolution PWM load to ground (PGx) routing minimises switching noise coupling into the ADC analog inputs. Always consult the manufacturer datasheet for full register definitions and electrical characteristics before committing to layout. This page synthesizes distributor pricing, drop-in alternatives drawn from the same dsPIC33CH family, and practical design notes beyond what the manufacturer datasheet provides as a single document.

見積もり お問い合わせ
DSPIC33CH256MP506T-I/MR - Dual-Core 100MHz DSC, 256KB Flash, 64-QFN | Microchip
DSPIC33CH256MP506T-I/MR

DSPIC33CH256MP506T-I/MR - Dual-Core 100MHz DSC, 256KB Flash, 64-QFN | Microchip

The Microchip Technology DSPIC33CH256MP506T-I/MR is a 16-bit dual-core Digital Signal Controller (DSC) from the dsPIC33CH family, operating at up to 200MHz (180MHz master + 100MHz slave core), with 328KB Flash and 64-QFN (9x9 mm) package. It is purpose-built for high-performance, precision motor control and digital power conversion applications where deterministic control loops and high-resolution PWM are required. The device supports Functional Safety (FuSa) features and includes CAN-FD communication, enabling robust automotive and industrial designs. A Digital Signal Controller (DSC) is a hybrid device that combines the interrupt-driven control strengths of a microcontroller (MCU) with the deterministic numerical processing power of a Digital Signal Processor (DSP). Within the broader semiconductor taxonomy, the DSC sits between microcontrollers (general-purpose control) and DSPs (math-heavy signal processing), and the dsPIC33CH family belongs to the larger 16-bit dsPIC33 lineage, designed for real-time mixed-signal embedded systems. The dual-core architecture is the distinguishing innovation: the master core runs the application and control loop, while the slave core offloads latency-critical DSP tasks such as field-oriented control (FOC) math, peak current-mode control, or audio processing. Key features include 328KB (328k x 8) of Flash program memory, dual dsPIC DSC cores (one 90 MIPS, one 100 MIPS), integrated high-resolution PWM modules, multiple CAN-FD controllers, and Functional Safety hardware that simplifies IEC 61508 SIL 2/3 and ISO 26262 ASIL-B system designs. Operating from 3.0V to 3.6V across -40C to +85C industrial temperature range, the device targets harsh embedded environments with deterministic interrupt response. The exposed-pad 64-QFN (9x9 mm) package supports efficient thermal dissipation for the high MIPS throughput. Typical applications include sensorless and sensored brushless DC (BLDC) motor drives, automotive traction inverters, digital power supplies with peak current-mode control, and high-performance digital audio processing. The slave-core architecture allows partitioning of code between application logic and DSP routines, accelerating time-to-market for complex control firmware. When designing with this part, allocate the master core to system scheduling and communication, and reserve the slave core for the time-critical inner control loop, which minimizes jitter and improves control bandwidth.

見積もり お問い合わせ
DSPIC33CH256MP506T-I/PT - 100MHz Dual-Core DSC, 256KB Flash | Microchip
DSPIC33CH256MP506T-I/PT

DSPIC33CH256MP506T-I/PT - 100MHz Dual-Core DSC, 256KB Flash | Microchip

The Microchip DSPIC33CH256MP506T-I/PT is a dual-core 16-bit Digital Signal Controller (DSC) from the dsPIC33CH family, integrating a 100 MHz main core and a 100 MHz slave core in a single 64-pin TQFP (10x10 mm) package with 256 KB of Flash, 32 KB SRAM, and 16 KB PRAM. The device supports 180 MHz / 200 MHz operation modes for advanced signal processing and is qualified for functional safety (FuSa) applications. A Digital Signal Controller (DSC) is a hybrid MCU-DSP device that combines a microcontroller's deterministic control peripherals with a digital signal processor's multiply-accumulate (MAC) engine. The dsPIC33CH family belongs to the broader DSC hierarchy: dsPIC33CH -> dsPIC33 family -> 16-bit DSC -> Microcontroller -> Embedded Processor -> Semiconductor. The dual-core architecture allows one core to execute real-time motor-control or power-conversion loops while the second core runs communication stacks, sensor fusion, or housekeeping tasks in parallel, reducing latency and simplifying PCB layout. Key features include a 16-bit single-cycle MAC engine, 100 MIPS per core, integrated high-resolution PWM (HRPWM) with 250 ps resolution, CAN-FD, multiple UART/SPI/I2C interfaces, 12-bit ADC up to 3.5 Msps, and 24-bit instruction word with 16-bit data path. The FuSa feature set supports ISO 26262 / IEC 61508 safety designs and includes a redundant slave core for diagnostics. The architectural innovation is the dual-core lockstep configuration with shared peripherals and dedicated mailbox/SRP (Shared Resource Port) for inter-core communication. Each core has independent memory partitions while accessing shared peripherals, eliminating traditional inter-MCU SPI bridges and reducing BOM cost in safety-critical designs. Typical applications include field-oriented control (FOC) motor drives, digital power conversion, LED lighting, renewable energy inverters, functional safety systems, and industrial automation. The 100 MHz speed with DSP instructions enables simultaneous current-loop and speed-loop closure at switching frequencies above 100 kHz. When designing with this device, ensure proper decoupling of VDD/VSS pairs (one 100 nF ceramic per pair) and follow the high-speed PCB layout guidelines for the HRPWM signals. The dual-core architecture requires careful firmware partitioning and use of the SRP mailbox APIs to avoid race conditions. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes for the DSPIC33CH256MP506T-I/PT not found on the manufacturer datasheet or distributor product pages.

見積もり お問い合わせ
DSPIC33CH256MP508-E/PT - Dual-Core 16-bit DSC 100MHz 256KB Flash | Microchip
DSPIC33CH256MP508-E/PT

DSPIC33CH256MP508-E/PT - Dual-Core 16-bit DSC 100MHz 256KB Flash | Microchip

The Microchip DSPIC33CH256MP508-E/PT is a 16-bit dual-core Digital Signal Controller (DSC) from the dsPIC33CH family, featuring a primary core running at 100 MIPS and a secondary core at 100 MIPS for parallel processing. It integrates 256 KB of Flash program memory, 328 KB total memory addressing, 32 KB of RAM, 80 KB PRAM, and is housed in an 80-pin TQFP package (12x12 mm). The device supports operating voltages from 3.0V to 3.6V and the automotive -40C to +125C temperature range. A Digital Signal Controller (DSC) is a hybrid microcontroller that combines a 16-bit MCU core with integrated DSP engine, on-chip high-resolution PWM, and enhanced peripherals. The dsPIC33CH family uniquely introduces a dual-core architecture that allows one core (master) to manage the application code while the secondary core (slave) handles time-critical control loops, offloading tasks like motor control algorithms, digital power conversion, or sensor fusion. This partitioning enables higher system performance and deterministic real-time response. Key features of the DSPIC33CH256MP508-E/PT include dual 16-bit dsPIC33 DSC cores, high-resolution PWM (typically 250 ps resolution) suitable for digital power and motor control, CAN FD interface for automotive networking, multiple UART/SPI/I2C peripherals, 8 DMA channels, 5 timers, and 2 serial I/O interfaces. The integrated DSP engine enables single-cycle MAC operations and saturating arithmetic for efficient control-loop computation. Typical applications include high-performance precision motor control (BLDC, PMSM, AC induction), digital power conversion (LLC, PFC, full-bridge converters), advanced sensor fusion and predictive maintenance, automotive body and chassis ECUs, and industrial automation drives. The dual-core architecture is particularly advantageous for functional safety systems where one core monitors the other. When designing with this device, ensure proper decoupling (100 nF + 10 uF near each VDD pin) and follow Microchip's layout guidelines for the high-resolution PWM outputs. The slave core can be configured for live update from the master core, enabling field firmware updates without halting real-time control. Developers should use MPLAB X IDE with the XC-DSC compiler to take full advantage of the dual-core programming model.

見積もり お問い合わせ
DSPIC33CH256MP508-I/PT - Dual-Core 100MHz DSC, 256KB Flash | Microchip
DSPIC33CH256MP508-I/PT

DSPIC33CH256MP508-I/PT - Dual-Core 100MHz DSC, 256KB Flash | Microchip

The Microchip Technology DSPIC33CH256MP508-I/PT is a dual-core 16-bit Digital Signal Controller (DSC) combining a 100 MIPS main dsPIC core and a 90 MIPS slave dsPIC core in a single 80-pin TQFP (PT) package. The device integrates 256 KB of Flash program memory, 32 KB of SRAM, and high-resolution PWM peripherals, making it suitable for advanced motor control, digital power conversion, and functional-safety applications. A Digital Signal Controller (DSC) is a hybrid architecture that merges the deterministic real-time control attributes of a microcontroller (MCU) with the computational throughput of a Digital Signal Processor (DSP). Within the broader taxonomy, this part sits at the hierarchy: dsPIC33CH DSC -> DSC -> MCU/DSP hybrid -> microcontroller family -> semiconductor. The dual-core dsPIC33CH architecture enables designers to separate time-critical control loops (main core) from housekeeping, communications, and safety monitoring tasks (slave core), a key advantage over single-core dsPIC33CK/CJ devices. Key features include 100 MHz main core operation (200 MIPS with dual-issue DSP), a 12-bit ADC with up to 3.5 MSPS throughput, 8 DMA channels, multiple communication interfaces (CAN-FD, I2C, SPI, UART), and high-resolution PWM outputs with 250 ps resolution. The integrated op-amps and comparators support advanced analog front-ends for field-oriented control (FOC) of BLDC, PMSM, and ACIM motors. Functional-safety features targeting IEC 61508 and ISO 26262 are built into the silicon. The main core typically runs the high-speed motor-control or digital-power loop, while the slave core manages communication stacks (CAN-FD, UART), housekeeping, or secondary control loops. The inter-core peripheral sharing mechanism allows the slave to access main-core peripherals and vice versa via a dedicated mailbox and shared RAM, eliminating the need for an external companion MCU in many functional-safety designs. The 80-pin TQFP (12x12 mm) package provides 69 usable I/O pins for extensive peripheral routing. Typical applications include high-performance BLDC/PMSM motor drives (e.g., e-bikes, drones, appliances), digital switch-mode power supplies, photovoltaic inverters, and industrial servo drives. Designers can also leverage the device in safety-critical systems that benefit from the dual-core lockstep-style architecture. The CAN-FD peripheral suits automotive and industrial networking, and the high-resolution PWM supports silicon-carbide (SiC) and gallium-nitride (GaN) power-converter gate drive. When designing with the DSPIC33CH256MP508-I/PT, allocate the main-core interrupt budget to the control loop and ensure the slave-core mailbox response time is bounded to avoid blocking main-core reads. Decoupling VDD/VBAT with 100 nF + 10 uF ceramic capacitors as close as practical to the pins is recommended. The /PT TQFP package supports hand-solderable debug but for high-volume assembly a 4-layer PCB with thermal vias under the exposed pad is preferred. This page synthesizes distributor pricing, drop-in alternatives, and practical design considerations for the DSPIC33CH256MP508-I/PT, supplementing the manufacturer datasheet with curated selection guidance.

見積もり お問い合わせ
DSPIC33CH256MP508T-I/PT - 100MHz Dual-Core DSC, 256KB Flash | Microchip
DSPIC33CH256MP508T-I/PT

DSPIC33CH256MP508T-I/PT - 100MHz Dual-Core DSC, 256KB Flash | Microchip

The Microchip DSPIC33CH256MP508T-I/PT is a 16-bit dual-core Digital Signal Controller (DSC) with 256 KB Flash, 32 KB RAM, integrated DSP, high-resolution PWM, and CAN-FD, in an 80-pin TQFP (12x12 mm) package with tape-and-reel delivery. The device pairs a 100 MIPS main core with a 90 MIPS slave core for task partitioning, a hallmark of the dsPIC33CH family aimed at high-performance precision motor control and digital power conversion. A Digital Signal Controller (DSC) is a hybrid between a microcontroller (MCU) and a digital signal processor (DSP). The MCU provides deterministic control loops and rich peripherals, while DSP extensions add single-cycle MAC, barrel shifter, and saturating arithmetic for fast fixed-point control loops. In the dsPIC33CH family, the main core handles application code while the slave core offloads latency-critical or proprietary IP tasks (such as motor commutation, custom DSP algorithms, or housekeeping firmware), communicating through shared memory and mailbox interrupts. As a member of the broader dsPIC33 family of DSCs, which sits in the microcontroller hierarchy, the 'CH' series specifically addresses dual-core partitioning and functional safety (FuSa) applications. Key features include up to 200 MHz operation with a 16-bit data path, 256 KB Flash program memory, 32 KB SRAM with up to 16 KB additional PRAM accessible to the slave core, integrated high-resolution PWM, dual 12-bit ADC modules (or 12-bit ADC plus 12-bit DAC on certain variants), CAN-FD peripherals for automotive networking, and a peripheral trigger generator for deterministic event-driven control. The 'I' suffix denotes an industrial -40C to +85C operating temperature range, and 'PT' indicates the TQFP-80 package. The dual-core architecture is engineered to remove the software bottleneck common in single-core MCUs running both commutation and application code. The slave core can run proprietary field-oriented control (FOC) or housekeeping tasks independently, while the main core manages communication, user interface, and supervisory logic. The high-resolution PWM (1.04 ns edge resolution) eliminates the need for many external gate-driver delays in digital power applications. Typical applications include precision motor control (PMSM, BLDC, AC induction, and stepper drives), digital power conversion (telecom rectifiers, server PSUs, solar inverters), automotive body and powertrain ECUs, and industrial sensor/servo control. Functional-safety (FuSa) variants support ASIL-B/SIL-2 systems. When designing with the 80-pin TQFP, allocate the four ADC pins per converter to adjacent MCU pins for clean differential layout, and place decoupling capacitors within 2 mm of each VDD/VSS pair. The slave core requires its own PRAM boot configuration; refer to Microchip's code examples for mailbox-based inter-core signaling.

見積もり お問い合わせ
DSPIC33CH512MP205-E/M4 - Dual-Core dsPIC33CH, 512KB Flash | Microchip
DSPIC33CH512MP205-E/M4

DSPIC33CH512MP205-E/M4 - Dual-Core dsPIC33CH, 512KB Flash | Microchip

The Microchip DSPIC33CH512MP205-E/M4 is a 16-bit dual-core digital signal controller (DSC) from the dsPIC33CH family, delivering up to 200 MHz on the master core and 180 MHz on the slave core in a 48-pin UQFN (6x6) package with exposed pad. The device integrates 512 KB Flash, 48 KB RAM on the master core and 16 KB RAM on the slave core, plus PRAM, and is qualified to the AEC-Q100 automotive standard with an extended -40C to +125C (E-temp) operating range. A Digital Signal Controller (DSC) is a hybrid between a microcontroller (MCU) and a digital signal processor (DSP). It combines deterministic interrupt-driven control logic with high-throughput DSP engines (single-cycle MAC, barrel shifter, zero-overhead looping). The dsPIC33CH family is a hierarchical superset: dsPIC33CH -> dsPIC33 -> 16-bit DSC -> MCU+DSP hybrid -> embedded processing core -> semiconductor. The dual-core architecture enables parallel execution of control and DSP tasks, eliminating the throughput bottlenecks of single-core designs in motor control and digital power conversion. Key features include dual dsPIC DSC cores with independent peripherals, 31x12-bit ADC and 4x12-bit DAC converters, high-resolution PWM (1 ns edge placement) suitable for precision motor control and digital power, plus CAN FD, I2C, SPI, UART/USART, IrDA and LINbus connectivity. Functional Safety (FuSa) features are integrated, supporting ISO 26262 system-level designs. The architecture uses a separate slave core to offload DSP tasks such as sensorless motor control algorithms, power factor correction, or digital power loops, while the master core runs the application layer and communication stacks. Independent peripheral sets on each core allow parallel deterministic execution without resource contention. Typical applications include automotive motor control (BLDC, PMSM, ACIM), digital power conversion (PFC, LLC, full-bridge), automotive sensor fusion, functional safety systems, and industrial servo drives. The 48-pin UQFN package is footprint-compatible with the dsPIC33CH256MP205 and dsPIC33CH128MP205 family members, simplifying PCB reuse across product variants. When designing with this part, note that the dual-core configuration requires a slightly different programming model: each core runs its own firmware image, and inter-core communication uses a dedicated mailbox register set. The exposed thermal pad on the UQFN package must be soldered to the PCB ground plane for proper thermal and electrical performance. This page synthesizes distributor pricing, AEC-Q100-qualified same-brand drop-in alternatives, and practical dual-core design notes not found in the manufacturer datasheet alone.

見積もり お問い合わせ