マイクロコントローラ

製品 (20,000+)

MPC8358ZQAGDDA - PowerQUICC II Pro 400MHz CPU | NXP | BGA-668
MPC8358ZQAGDDA

MPC8358ZQAGDDA - PowerQUICC II Pro 400MHz CPU | NXP | BGA-668

The NXP MPC8358ZQAGDDA is a PowerQUICC II Pro integrated communications processor featuring a PowerPC e300 core running at 400MHz, housed in a 668-pin PBGA-PGE (29x29) package with exposed pad. Belonging to the MPC83xx PowerQUICC II Pro family, it is engineered for small-to-medium enterprise routers and similar packet-processing applications where deterministic throughput and rich peripheral integration matter. The non-E suffix indicates the part runs from 0C to 105C and ships without the security engine block that distinguishes the MPC8358E variant. A PowerQUICC processor is a system-on-chip that combines a PowerPC CPU with communications peripherals and a hardware acceleration engine; the PowerQUICC II Pro family (an MPC83xx derivative of the original PowerQUICC II) targets mid-range wired networking where the device must terminate DDR memory, perform DMA on packet data, and present industry-standard I/O such as PCI, USB, Ethernet MACs, TDM, and ATM interfaces on a single die. Key features include the e300 core with MMU and hardware cache coherency, an integrated DDR1/DDR2 memory controller with ECC, dual 10/100/1000 Ethernet MACs (one RGMII plus one GMII), a 32-bit PCI interface (up to 66MHz), USB 2.0 full-speed PHY, and multi-channel TDM/ATM glue for legacy telecom interconnects. The QUICC Engine datapath offers hardware acceleration for PPP, HDLC, ATM AAL, Ethernet bridging, and policing; this lets an OEM run multi-megabit aggregate traffic at line rate without consuming CPU cycles. The architecture pairs the e300 core with the QUICC Engine block, which executes time-critical protocol processing in dedicated microcode. The 400MHz core supplies the control plane for routing tables, management plane tasks, and QoS queuing while the QUICC Engine manages the data plane. The 668-PBGA-PGE package provides a thermal pad tied to a copper pour for heat removal, but typical router designs of this era dissipate only a few watts, allowing passive cooling. Typical applications include small-to-medium enterprise routers, business gateways, xDSL IADs, SOHO security appliances, and Industrial Ethernet bridges. Pin-to-pin compatible part variants such as MPC8358EVRAGDDA and MPC8358CVRAGDDA target different operating envelopes or feature sets within the same board layout. When designing with this device, allocate adequate copper area under the exposed pad and follow the NXP application note for DDR2 termination to meet SI margins; reference the MPC8360E reference board where possible to shorten design cycles and reuse the QUICC Engine firmware framework. This page consolidates distributor pricing (as of 2026-10-17), MPC83xx family alternative candidates, and design notes that go beyond the manufacturer datasheet summary to support procurement and board-level decisions.

見積もり お問い合わせ
MPC8360ECVVAGDGA - 400MHz PowerQUICC II Pro MPU | NXP | 740-TBGA
MPC8360ECVVAGDGA

MPC8360ECVVAGDGA - 400MHz PowerQUICC II Pro MPU | NXP | 740-TBGA

The NXP MPC8360ECVVAGDGA is a 400 MHz PowerQUICC II Pro integrated communications processor built on Power Architecture technology, integrating one e300 core with 32-bit PowerPC instruction set and a high-performance communication engine, housed in a 740-ball TBGA (37.5 x 37.5 mm) package. A microprocessor (MPU) is a single-chip processing unit that integrates the CPU core, cache, memory controller and a wide range of peripheral interfaces on a single die, sitting at the top of the embedded-system hierarchy: MPU -> processor SoC -> system-on-chip -> integrated circuit. The PowerQUICC II Pro family extends the classic PowerQUICC II line by adding gigabit Ethernet, DDR1/DDR2 memory support, USB, TDM/ATM and security accelerators, while maintaining software compatibility with prior PowerQUICC designs. Key features include an integrated security engine (SEC) for IPsec and SSL acceleration, dual DDR1/DDR2 memory controllers with ECC, PCI interface for legacy expansion, gigabit Ethernet MAC, USB 2.0 full-speed, TDM and ATM serial interfaces, and an extended industrial temperature range of -40C to +105C. The device targets communications infrastructure where deterministic networking and crypto offload are required. The MPC8360E implements a classic single-issue e300 superscalar core with separate 32 KB instruction and 32 KB data L1 caches, plus a unified 256 KB L2 cache. The QUICC Engine communication block handles ATM, HDLC, TDM and POS functions in hardware, freeing the core for control-plane processing. Silicon revision 2.x (denoted by the 'E' suffix) adds the gigabit Ethernet MAC and integrated SEC. Typical applications include SMB/SME routers, DSLAMs, IP-PBX systems, industrial gateways and line cards where the QUICC Engine handles wire-speed TDM/ATM while the e300 core runs Linux or VxWorks control-plane software. The industrial -40C to +105C operating range and lead-free TBGA package make it suitable for outdoor or ruggedized CPE equipment. Designers should note that lead-free TBGA assembly requires peak reflow temperatures of 245C to 260C, and the 37.5 x 37.5 mm package demands a 4-layer or higher PCB with controlled-impedance routing for DDR2, PCI and gigabit Ethernet signals. DDR2 termination and length matching must follow the JEDEC JESD79-2 specification. This page synthesizes distributor pricing, same-family NXP drop-in alternatives and pin-compatibility notes that go beyond the manufacturer datasheet summary, helping engineers select the right PowerQUICC II Pro variant for their communications design.

見積もり お問い合わせ
MPC8360ECVVAJDGA - PowerQUICC II Pro SoC, 533MHz | NXP
MPC8360ECVVAJDGA

MPC8360ECVVAJDGA - PowerQUICC II Pro SoC, 533MHz | NXP

The NXP MPC8360ECVVAJDGA is a PowerQUICC II Pro communications processor built on the e300 core, delivering 533 MHz of 32-bit Power Architecture performance inside a 740-pin TBGA (37.5x37.5 mm) package. It integrates DDR1/DDR2 memory controllers, PCI, 1 GbE, USB, TDM, ATM, and an SEC security engine, forming a single-chip platform for wired networking and secure communications. The "JD" speed-grade code identifies the 533 MHz core frequency at a 1.2 V core supply. A PowerQUICC II Pro SoC is a system-on-chip family that originated in Freescale's MPC8xx line and evolved into the MPC83xx/MPC83xxx platform. PowerQUICC devices combine a Power Architecture CPU with specialized communications peripherals (QUICC Engine or sub-engines, Ethernet MACs, ATM controllers, security accelerators) to offload protocol processing from the CPU. They sit at the system-controller tier of networking equipment, between PHYs/transceivers (physical layer) and the host control plane, and are commonly used in SOHO/SMB routers, DSLAM line cards, industrial gateways, and secure access equipment where deterministic protocol handling matters more than raw clock speed. Key specifications include a 32-bit e300 core at 533 MHz, integrated DDR1/DDR2 SDRAM controller, dual 10/100/1000 Ethernet MACs with QoS and classification, 32-bit PCI 2.2 interface, USB 2.0, TDM/ATM segmentation, and an integrated SEC 2.x cryptographic accelerator. The device operates across -40 °C to +105 °C junction temperature and supports 1.2 V core / 2.5 V / 3.3 V I/O rails typical of MPC83xx designs. Architecturally, the MPC8360E uses a parallel e300 core with hardware MMU, dedicated DDR memory controller with ECC, a multi-channel DMA engine, and a peripheral set mapped through a unified internal bus. Hardware-level IPsec, SSL/TLS, and bulk cipher acceleration through SEC offload the CPU and reduce latency for VPN/secure routing workloads. The 740-TBGA package provides sufficient routing density for the full peripheral set while remaining compatible with mainstream PowerQUICC PCB layouts. Typical applications include SOHO/SMB routers and modems, secure VPN gateways, industrial Ethernet switches, DSLAM/access equipment line cards, and networked printers. The integrated security engine and dual GbE ports make it well suited to edge-of-network devices that terminate VPN tunnels or enforce IPsec/SSL. When designing with this part, allocate a contiguous 740-ball TBGA land pattern, use at least 4-layer PCB with dedicated power planes, and follow NXP's hardware specifications for DDR2 trace length matching and termination. The Rev 1 silicon revision is the reference baseline; verify errata against the latest NXP hardware specifications document before committing to layout. This page synthesizes current distributor stock, NXP datasheet parameters, drop-in PowerQUICC alternatives, and design considerations that go beyond the manufacturer datasheet, so engineers can shortlist the part faster and avoid common PCB-layout pitfalls.

見積もり お問い合わせ
MPC8360EVVAGDGA - PowerQUICC II Pro SoC, 400MHz, 740-TBGA | NXP
MPC8360EVVAGDGA

MPC8360EVVAGDGA - PowerQUICC II Pro SoC, 400MHz, 740-TBGA | NXP

The NXP (formerly Freescale) MPC8360EVVAGDGA is a PowerQUICC II Pro integrated communications processor built on Power Architecture technology, operating at 400 MHz with a single e300 core in a 740-ball TBGA package (37.5x37.5 mm). This SoC combines a 32-bit Power Architecture processor core, a security engine (SEC), DDR1/DDR2 memory controller, PCI interface, 1 GbE MAC, USB 2.0, TDM, and ATM support on a single die for unified communications and networking equipment. A communications SoC (System-on-Chip) is an integrated circuit that combines a microprocessor core, on-chip peripherals, memory controllers, and protocol-specific hardware accelerators (such as security engines and Ethernet MACs) onto a single silicon die, reducing board area and BOM cost compared to a discrete MPU plus external bridges. The MPC8360E PowerQUICC II Pro family is a next-generation extension of the PowerQUICC II line targeting routers, DSLAMs, media gateways, and industrial control platforms where one chip must terminate multiple telecom/ datacom protocols simultaneously. Key features include the e300 core running at 400 MHz, integrated DDR1/DDR2 SDRAM controller with ECC, 32-bit PCI 2.2 interface, 32-bit/36-bit SEC (security engine) for IPSec/SSL offload, one tri-speed 10/100/1000 Mb/s Ethernet MAC, USB 2.0 host/device, TDM/H.110 interface, ATM SAR support, and a local bus controller. Operating voltage is 1.2 V core with 3.3 V I/O. The 0 to 105C ambient operating range suits commercial and industrial environments. The MPC8360EVVAGDGA architecture separates the e300 core from the CPM (Communication Processor Module) co-processor that handles DMA and protocol termination in hardware, offloading packet processing from the main CPU. This dual-engine structure lets one chip sustain line-rate encryption (SEC) plus GbE bridging without saturating the core, which is the key reason PowerQUICC II Pro devices remain in service in long-life networking and industrial platforms. Typical applications include SOHO routers, xDSL line cards, integrated access devices, media gateways, industrial control routers, and secure appliance controllers. Compared to MPC8358E devices the MPC8360E adds PCI-X and additional USB PHYs; compared to MPC8360EZU variants the EVVAGDGA retains all features with the specific 740-TBGA (37.5x37.5 mm) outline specified for this order code. When designing with this part, allocate adequate PCB footprint for the 37.5x37.5 mm TBGA, keep DDR traces length-matched within the controller's published skew budget, and review the Rev 2.x hardware specification document for JTAG, reset, and PLL filtering guidance. This page synthesizes distributor stock data, same-package MPC8360 variants, and practical hardware design notes not aggregated in any single manufacturer PDF.

見積もり お問い合わせ
MPC8360EZUAGDGA - PowerQUICC II Pro 400MHz SoC | NXP
MPC8360EZUAGDGA

MPC8360EZUAGDGA - PowerQUICC II Pro 400MHz SoC | NXP

The NXP MPC8360EZUAGDGA is a PowerQUICC II Pro integrated communications processor built on the e300 system-on-chip (SoC) platform, featuring a 32-bit Power Architecture core running at 400 MHz in a 740-pin TBGA package (37.5 x 37.5 mm). It integrates a next-generation communications engine alongside DDR1/DDR2 memory controllers, PCI, 1 Gbit Ethernet, USB, TDM, ATM, and security acceleration, making it suitable for broadband access, SME routing, and industrial gateway designs. A PowerQUICC II Pro processor is a member of NXP's (formerly Freescale) PowerQUICC family of integrated communications processors. It combines a high-performance Power Architecture CPU core with dedicated communications peripherals and an SoC fabric, extending the popular PowerQUICC II line into next-generation networking and embedded designs. The architecture hierarchy places it under: PowerQUICC II Pro family -> MPC83xx series -> PowerQUICC communications processors -> microprocessors -> integrated circuits. Key features include a 400 MHz e300 core, integrated DDR1/DDR2 memory controller supporting up to 2 GB of RAM, a 32-bit PCI interface, dual 10/100/1000 Ethernet MACs with hardware acceleration, USB 2.0 full/low-speed host and device, TDM and ATM interfaces, and an integrated security engine (SEC) for crypto offload. The 740-TBGA package uses a 1 mm pitch and provides ample I/O for multi-protocol bridging applications. The architecture implements a unified coherent bus connecting the e300 core, L2 cache, and peripheral controllers, enabling deterministic throughput for packet processing workloads. The SEC block accelerates DES, 3DES, AES, SHA-1/MD5 and public-key operations without burdening the host CPU, while the QUICC Engine subsystem handles TDM, ATM, and HDLC channelization. Typical applications include small-to-medium enterprise (SME) routers, low-end DSLAMs, IP private automatic branch exchanges (PABXs), industrial gateways, and secure broadband access equipment. The 0 to 105 C operating temperature range supports thermally constrained embedded deployments. When designing with this part, plan PCB stack-up and power sequencing carefully - the 740-TBGA package demands controlled-impedance routing, multiple ground and power planes, and matched-length DDR2 traces. Validate DDR2 IBIS models against your chosen DRAM vendor and budget for the SEC crypto block if your firmware stack depends on it.

見積もり お問い合わせ
MPC8360EZUAJDGA - 533MHz PowerQUICC II Pro MPU, TBGA-740 | NXP
MPC8360EZUAJDGA

MPC8360EZUAJDGA - 533MHz PowerQUICC II Pro MPU, TBGA-740 | NXP

The NXP MPC8360EZUAJDGA is a PowerQUICC II Pro integrated communications processor built on Power Architecture technology, operating up to 533 MHz core frequency and packaged in a 740-ball TBGA (37.5 x 37.5 mm, 1 mm pitch). It integrates an e300 core with QUICC Engine communications acceleration, DDR1/DDR2 memory controller, PCI, 1 Gbit Ethernet, USB, TDM, ATM and SEC crypto accelerator blocks on a single die, targeting wired communications and broadband access equipment. A PowerQUICC processor is a family of integrated communications microprocessors from Freescale (now NXP) that combine a Power Architecture CPU with specialized networking peripheral logic. The PowerQUICC II Pro generation extends the original PowerQUICC II line by adding higher CPU frequencies, DDR memory support, gigabit Ethernet MACs, and a hardware security engine. In the system hierarchy, it sits as an MPU (microprocessor unit) within Power Management and embedded processing, used where deterministic packet processing and rich peripheral integration are required. Key features include a 533 MHz e300 core, integrated QUICC Engine supporting common WAN protocols, dual GbE MACs with SGMII support, DDR1/DDR2 memory controller with ECC, USB 2.0 full-speed interface, PCI 2.2 bus, and an SEC 2.0+ cryptographic accelerator for IPsec and other security offload. The device operates from a 1.2 V core supply with 1.8 V/2.5 V/3.3 V I/O rails. The MPC8360E uses a 0.13 um CMOS process and integrates roughly 100 million transistors, balancing performance with power for line-card and edge-router applications. The QUICC Engine offloads protocol processing from the e300 core, allowing wire-speed handling of ATM, Ethernet, TDM and MPLS traffic without CPU saturation. Typical applications include small-to-medium enterprise routers, DSLAM line cards, IP-PBX systems, wireless base station controllers, and industrial networking gateways where integrated communications peripherals replace discrete MACs, PHYs and protocol processors. When designing with this device, ensure the TBGA-740 land pattern uses 1 mm pitch with proper thermal via arrays under the die, and sequence the 1.2 V core rail before the 1.8/2.5/3.3 V I/O rails to prevent I/O latch-up. Boot configuration is sampled from reset and must be set before POR deassertion. This page synthesizes distributor pricing, same-family NXP drop-in variants, end-of-life status signals, and practical PCB/design notes not found in the bare manufacturer datasheet.

見積もり お問い合わせ
MPC8360VVAGDGA - PowerQUICC II Pro 400MHz SoC | NXP
MPC8360VVAGDGA

MPC8360VVAGDGA - PowerQUICC II Pro 400MHz SoC | NXP

The NXP MPC8360VVAGDGA is a PowerQUICC II Pro integrated communications processor built around the e300 core running at 400 MHz, housed in a 740-pin TBGA package (37.5 x 37.5 mm). It integrates DDR1/DDR2 memory controllers, PCI, 1 Gbit Ethernet, USB, TDM, and ATM interfaces, providing a System-on-Chip (SoC) platform for cost-sensitive networking and communications equipment. The device is part of NXP's MPC83xx PowerQUICC family, which extends the legacy PowerQUICC II line with Power Architecture technology. A communications SoC is a single silicon device that combines a microprocessor core, on-chip peripherals, memory interfaces, and dedicated communications accelerators into one package; in the case of the MPC8360VVAGDGA, that combination targets broadband access, industrial networking, and telecom line-card applications. The MPC8360 sits within the broader taxonomy: microprocessor -> MPU -> application processor -> communications SoC -> PowerQUICC family. By integrating the QUICC Engine and QUICC Engine HDLC/ATM/TDM controllers alongside the e300 core, the device eliminates the need for an external traffic-handling ASIC in many designs. Key specifications for the MPC8360VVAGDGA include the 400 MHz e300 core frequency, 1.2 V core supply, 1.8/2.5/3.3 V I/O supply, 32-bit architecture with single core, 740-TBGA package, and an operating temperature range of 0C to 105C. On-chip peripherals include DDR1/DDR2 memory controller, 32-bit PCI v2.3 bus, one 10/100/1000 Ethernet MAC (RGMII), one USB 2.0 (host/device), local bus, and serial interfaces (UART, I2C, SPI). The integrated QUICC Engine subsystem offloads HDLC, ATM, and TDM processing from the e300 core, enabling sustained wire-speed handling of multi-channel traffic without CPU intervention. The architecture combines a Power Architecture e300 superscalar core with a dedicated RISC communications engine, sharing an internal SoC platform bus. This dual-engine topology allows the device to handle routing protocols, encryption, and control-plane tasks on the e300 core while the QUICC Engine simultaneously processes time-critical channelized traffic, achieving deterministic throughput across voice and data workloads. Typical applications for the MPC8360VVAGDGA include broadband CPE/SME routers, low-end DSLAM line cards, IP-PBX and IP-PSTN gateways, industrial Ethernet gateways, and ATM-to-IP protocol converters. Its integrated 1 GbE MAC plus QUICC Engine makes it well suited for hybrid TDM/IP equipment in legacy telecom infrastructure transitioning toward all-IP. When designing with this part, note that the NXP product page reports this MPN has reached End of Life; designers should evaluate the pin-compatible MPC8358EVRAGDGA or MPC8360EVVAGDGA variants for new designs and source the MPC8360VVAGDGA from authorized distributors for legacy/field replacement purposes. This page synthesizes EOL notices, distributor pricing, drop-in compatible variants, and PCB-level design notes that go beyond the information density found in the manufacturer datasheet alone.

見積もり お問い合わせ
MPC8360ZUAGDGA - 400MHz PowerQUICC II Pro MPU | NXP
MPC8360ZUAGDGA

MPC8360ZUAGDGA - 400MHz PowerQUICC II Pro MPU | NXP

The NXP MPC8360ZUAGDGA is a PowerPC e300 microprocessor in the PowerQUICC II Pro family, integrating one 32-bit core running at 400MHz in a 740-pin TBGA (37.5x37.5 mm) package. Built on Power Architecture technology, this non-encryption variant combines a high-performance e300 core with a robust communications engine, targeting networking and embedded telecom systems. The device is part of NXP's MPC83xx line extending the popular PowerQUICC II family with DDR1/DDR2 memory controller support, PCI, Gigabit Ethernet, USB, TDM and ATM interfaces. Operating temperature range is 0C to 105C per the datasheet. PowerQUICC II Pro processors are integrated communications processors that combine a Power Architecture CPU core with a peripheral subsystem optimized for WAN, LAN, and wireless protocol termination. Within the broader product taxonomy they sit between general-purpose embedded CPUs and dedicated network processors, and are widely used in routers, DSLAM line cards, industrial control, and secure access equipment where deterministic communications throughput matters more than raw GHz. The 'non-ENCRP' suffix indicates the silicon security/firmware module is not enabled in this part number, distinguishing it from the MPC8360E sister devices. Key features include the e300 superscalar core with separate 32KB instruction and 32KB data caches, dual DDR1/DDR2 memory controllers with ECC support, a 32-bit/66MHz PCI controller, a single 10/100/1000 Ethernet MAC, USB 2.0 (full-speed), multiple TDM serial interfaces for T1/E1/J1/HDLC/ATM, and a system-on-chip local bus. Security-minded peripherals such as SEC 2.0 are not included in this non-encryption variant; teams needing crypto acceleration should evaluate the MPC8360E sister part. The 740-TBGA package exposes all address, data, and peripheral pins to support four DIMM banks and full-width PCI/PCI-X interconnect. Typical applications include SOHO and enterprise router control planes, DSLAM line card processors, industrial Ethernet gateways, multi-protocol bridge/router modules, and telecom line-interface cards. The 400MHz core is well-matched to routing tables in the 64K-256K-entry range, fast-path forwarding of encrypted VoIP traffic, and protocol-aware QoS scheduling. The integrated DDR1/DDR2 controller eliminates external memory bridge silicon, reducing BOM cost and PCB area, while the TDM interfaces support legacy PSTN interworking alongside modern Ethernet/IP backhaul. When designing with this device, plan the 740-TBGA layout on a minimum 8-layer PCB with matched-impedance differential pairs for DDR2 and Ethernet. Provide a dedicated 1.2V core supply with at least 1uF of ceramic bypass per power pin, and isolate the analog PLL section with a quiet ferrite-filtered rail. Programming of boot ROM, memory initialization, and pin multiplexing must follow the MPC8360E hardware specifications reference manual; errors here are the most common cause of non-booting boards.

見積もり お問い合わせ
MPC8360ZUAJDGA - PowerQUICC II Pro MPU, 533MHz e300, 740-TBGA | NXP
MPC8360ZUAJDGA

MPC8360ZUAJDGA - PowerQUICC II Pro MPU, 533MHz e300, 740-TBGA | NXP

The NXP MPC8360ZUAJDGA is a PowerQUICC II Pro integrated communications microprocessor based on the Power Architecture e300 core, clocked at 533 MHz in a 740-ball T-BGA (TBGA) package measuring 37.5 mm x 37.5 mm. It integrates a 32-bit CPU core, DDR1/DDR2 memory controller, PCI, 1 GbE, USB, TDM, and ATM interfaces, targeting wired communications infrastructure including routers, DSLAMs, and line cards. The device is built on a 0.13 micron CMOS process and supports multiple voltage rails (1.8 V, 2.5 V, 3.3 V). A PowerQUICC (pronounced "power-quic") processor is a family of communications microprocessors originating at Motorola Semiconductor (later Freescale, now NXP) that combines a Power Architecture CPU with integrated communications peripherals such as Ethernet MACs, ATM controllers, HDLC, TDM, and PCI. Within the broader taxonomy, the MPC8360 sits as a microprocessor IC -> embedded microprocessor -> communications MPU -> PowerQUICC II Pro family -> semiconductor IC. Its primary role in a system hierarchy is to consolidate CPU plus connectivity into a single SoC, eliminating external protocol-handling ASICs. Key differentiating features of the MPC8360ZUAJDGA include its 533 MHz e300 core with 32 KB L1 instruction cache and 32 KB L1 data cache, hardware QUICC Engine technology for accelerated communications, integrated DDR1/DDR2 memory controller with ECC support, dual 10/100/1 Gb Ethernet, USB 2.0 host/device, PCI 2.2 bus interface, and TDM/ATM serial interfaces. Operating temperature range spans 0 C to 105 C (TA = -40 C to +125 C for the silicon), making it suitable for thermally managed equipment enclosures. Architecturally, the MPC8360E family uses a Harvard-style e300 core with separate instruction and data MMUs, a unified internal bus, and a multi-channel QUICC Engine subsystem that offloads protocol processing from the CPU. The 740-TBGA package provides the pin density required for the parallel DDR, PCI, Ethernet GMII, and QUICC Engine serial interfaces, and is paired with a thermal pad for board-mounted heat-spreading. Typical applications include SME (small-to-medium enterprise) routers, low-end DSLAMs, IP-PBX systems, line cards for multiservice access nodes, and industrial wired backhaul platforms. In these applications, the integrated communications peripherals allow a single MPU plus external PHYs and DSPs to form a complete line card or CPE platform. When designing with this part, allocate proper thermal dissipation because the 740-TBGA dissipates significant power at 533 MHz; design stack-up for matched-impedance DDR2 traces, 50 ohm controlled-impedance Ethernet, and 100 ohm differential QUICC Engine serdes; and verify DDR2 IBIS models against the chosen DIMM topology. This page synthesizes distributor stock and lead-time data, drop-in alternative MPNs from the MPC83xx family, and practical PCB/thermal design notes that complement the manufacturer hardware specifications document.

見積もり お問い合わせ
MPC8360ZUALFHA - PowerQUICC II Pro, e300, 667 MHz MPU | NXP
MPC8360ZUALFHA

MPC8360ZUALFHA - PowerQUICC II Pro, e300, 667 MHz MPU | NXP

The NXP MPC8360ZUALFHA is a PowerQUICC II Pro integrated communications processor built on the e300 system-on-chip (SoC) platform, delivering a 32-bit Power Architecture core running at 667 MHz in a 740-pin TBGA (37.5 mm x 37.5 mm) package at 1.0 mm pitch. Targeted at cost-effective, highly integrated communications equipment, this device integrates DDR1/DDR2 memory controllers, PCI, 1 Gigabit Ethernet, USB, TDM, and ATM interfaces on a single die. A PowerQUICC II Pro processor is a system-on-chip designed for wired and wireless communications infrastructure, combining a Power Architecture CPU core with specialised communications peripherals. The e300 core family evolved from the classic PowerQUICC II line and adds enhanced peripheral integration, allowing OEMs to reduce component count in routers, DSLAMs, media gateways, and industrial control equipment. The MPC8360 family supports revision 2.x of the silicon, which improves the DDR memory controller and adds hardware acceleration blocks used for protocol termination. Key features of the MPC8360ZUALFHA include the e300 core with 32 KB instruction and data L1 caches, a 333 MHz local bus, dual 10/100/1000 Ethernet MACs, a 32-bit/66 MHz PCI controller, USB 2.0 (Full/Low speed), a security engine (SEC 2.0), and four TDM/ATM serial interfaces. The integrated DDR1/DDR2 memory controller with ECC supports up to 2 GByte of addressable memory, and the QUICC Engine multi-channel peripheral handles up to 64 HDLC or transparent channels per port. The device operates from a 1.2 V core supply with 3.3 V I/O, and the 740-pin TBGA package provides the signal density required for the wide peripheral set. Technical depth: The e300 core implements the Power Architecture 32-bit instruction set and supports out-of-order execution pipelines tailored to communications workloads. The QUICC Engine runs as a microcoded RISC engine that offloads protocol processing from the CPU, freeing the e300 core for control plane and management tasks. The memory subsystem includes a 256 KB internal SRAM that can be configured as L2 cache or as a packet buffer. Typical applications include enterprise routers and switches, DSL and cable modem termination equipment, media gateways, industrial Ethernet gateways, network-attached storage controllers, and PCI-based communications boards. The combination of PCI, Gigabit Ethernet, and the QUICC Engine makes the MPC8360 particularly well suited to multi-service access platforms that must terminate both legacy TDM traffic and packet-based services. When designing with the MPC8360ZUALFHA, careful attention must be paid to the power supply decoupling network, signal integrity on the DDR memory bus, and the TBGA layout requiring microvia or wire-bond-compatible PCB technology. Designers should consult the NXP hardware specifications document for the full ball-map, thermal design recommendations, and reference schematics. This page synthesises distributor pricing, drop-in alternatives from the same NXP family, and practical design notes beyond what the manufacturer datasheet alone provides, helping procurement and hardware engineers evaluate the part quickly.

見積もり お問い合わせ
MPC8377CVRALG - PowerQUICC II Pro MPU 667MHz e300c4s | NXP 689-TEPBGA
MPC8377CVRALG

MPC8377CVRALG - PowerQUICC II Pro MPU 667MHz e300c4s | NXP 689-TEPBGA

The NXP MPC8377CVRALG is a PowerQUICC II Pro microprocessor featuring a single e300c4s core running at 667MHz with a 32-bit data bus width, housed in a 689-ball TEPBGA II (31x31mm) package. Built on a 0.09-micron process technology, this MPC83xx family SoC integrates a PowerPC e300 processor core with QUICC Engine technology for high-throughput networking and telecom I/O offload. The device supports multiple voltage rails of 1.8V, 2.5V, and 3.3V to power core, DDR memory, and I/O domains independently. A microprocessor (MPU) is the central processing unit of an embedded computing system that fetches, decodes, and executes instructions while coordinating memory and peripherals. The MPC83xx hierarchy positions this part as a PowerQUICC II Pro communications processor: MPU -> embedded processor -> PowerPC -> PowerQUICC -> communications SoC -> semiconductor. By combining a PowerPC CPU with a multi-channel QUICC Engine, the part replaces what previously required a CPU plus an external network ASIC, reducing board area and BOM cost while accelerating frame forwarding in routing and switching gear. Key features include hardware-accelerated protocol handling for Ethernet, ATM, and HDLC/PPP through the QUICC Engine subsystem, an integrated DDR1/DDR2 memory controller with ECC support, a 32-bit PCI interface, dual 10/100/1000 Ethernet MACs, and flexible I/O voltage support. The TEPBGA-689 thermal-enhanced plastic BGA delivers robust thermal performance for sustained throughput in fan-cooled and conduction-cooled platforms. Operating temperature spans -40C to +105C for industrial and extended commercial deployments. Architecturally, the e300c4s core superscalar pipeline issues up to two instructions per cycle with out-of-order completion, while the QUICC Engine offloads serial-bit, byte-level, and DMA-intensive tasks from the core. This separation allows deterministic throughput for L2/L3 forwarding, VPN termination, and storage protocols even when the host CPU runs control-plane management stacks. Integrated security accelerators handle DES, 3DES, AES, and MD/SHA hashing at line rate. Typical applications include industrial routers and switches, VoIP and unified threat management (UTM) gateways, DSLAM line cards, networked storage RAID controllers, and Smart Energy / IEC 61850 substation equipment. The 667MHz speed grade balances headroom for control-plane software with deterministic data-plane throughput demanded by service-provider edge devices. When designing with this part, ensure the PCB provides a sufficient ground and power plane stack-up under the 31x31mm BGA; trace escape for the 689-ball array requires microvia or sequential lamination technology. Designers should follow the NXP Hardware Design Guide for PowerQUICC II Pro to manage DDR2 topology, QUICC Engine SERDES reference clock cleanliness, and decoupling network placement. The 'C' suffix denotes commercial operating temperature, while the 'VR' speed grade places the device in the validated mid-frequency tier rather than the top 800MHz bin. This page synthesizes distributor pricing, cross-reference alternatives, and practical design guidance not consolidated in the NXP MPC8377 datasheet, giving engineers a single decision source for sourcing and substituting this legacy PowerQUICC processor.

見積もり お問い合わせ
MPC8377EVRAJF - PowerQUICC II Pro MPU 533MHz e300c4s | NXP
MPC8377EVRAJF

MPC8377EVRAJF - PowerQUICC II Pro MPU 533MHz e300c4s | NXP

The NXP MPC8377EVRAJF is a PowerQUICC II Pro microprocessor based on the PowerPC e300c4s core, integrating a single 32-bit core running at 533 MHz with dedicated hardware accelerators for security, pattern matching, and TCP/IP offload. The device ships in a 689-TEPBGA II (31x31 mm) package and is targeted at cost-effective, low-power, highly integrated host-processor applications such as SOHO routers, WiMAX CPE, industrial control, and secure networking appliances. A PowerQUICC II Pro processor is a system-on-chip (SoC) built around a PowerPC core that integrates peripheral controllers, security engines, and networking accelerators into one package. In the broader taxonomy, the MPC8377E sits within the PowerQUICC family -> PowerPC MPU -> embedded microprocessor -> integrated circuit -> semiconductor. This integration reduces BOM cost and PCB area versus a discrete CPU-plus-controller design, while the built-in encryption engine accelerates IPsec, SSL/TLS, and other crypto workloads at line rate. Key features highlighted in the NXP datasheet include a 32-bit e300c4s core with MMU and double-precision FPU, integrated security engine (SEC 4.0), a QUICC Engine communications subsystem, DDR2 memory controller, PCI Express interface, dual Gigabit Ethernet MACs, and versatile I/O voltage support at 1.8V, 2.5V, and 3.3V. The 533 MHz core frequency balances throughput and power for fanless embedded designs. Architecturally, the MPC8377EVRAJF combines a superscalar PowerPC core, a high-bandwidth on-chip bus fabric, and the QUICC Engine for protocol acceleration. The security engine handles symmetric (AES, 3DES) and asymmetric (RSA, ECC) algorithms in hardware, offloading the core and enabling sustained encrypted throughput at gigabit line rates. Typical applications include SOHO routers, network-attached storage (NAS), secure VPN gateways, WiMAX/LTE customer-premises equipment, and industrial automation controllers. The wide I/O voltage flexibility also supports legacy 3.3V peripherals alongside modern 1.8V DDR2 memory. When designing with this part, ensure the 689-TEPBGA land pattern and 31x31 mm PCB footprint are respected, provide adequate decoupling, and follow NXP's hardware-design checklist for DDR2 fly-by topology and QUICC Engine reference clocking. Thermal management at 533 MHz depends on the board's copper area and airflow. This page synthesizes distributor pricing, drop-in same-package alternatives within the PowerQUICC II Pro family, and practical design notes not aggregated in the manufacturer datasheet alone.

見積もり お問い合わせ
MPC8377EVRAJFA - 533MHz PowerQUICC II Pro SoC MPU | NXP
MPC8377EVRAJFA

MPC8377EVRAJFA - 533MHz PowerQUICC II Pro SoC MPU | NXP

The NXP MPC8377EVRAJFA is a PowerQUICC II Pro communications processor built around the Power Architecture e300c4s core, integrating DDR1/DDR2 memory controllers, dual PCI Express controllers, dual SATA-II interfaces, USB 2.0, gigabit Ethernet, and a security engine in a single 689-TEPBGA II package (31x31 mm). It runs at 533 MHz and is targeted at cost-sensitive small-to-medium business networking, storage, and embedded consumer applications. The integrated peripherals significantly reduce bill-of-materials cost and PCB complexity for entry-level routers, NAS appliances, and industrial control platforms. A microprocessor MPU (Microprocessor Unit) is the central processing integrated circuit that executes operating system and application code in an embedded system. The MPC8377E belongs to the PowerQUICC II Pro family of communications processors, a sub-category of microprocessors that combines a CPU core with high-speed serial interfaces and a system-on-chip peripheral set for wired networking equipment. Within the broader taxonomy, it sits under microcontrollers/microprocessors -> SoC processors -> communications processors -> networking SoCs. Key features include 32 KB of instruction and 32 KB of data L1 cache, an integrated DDR1/DDR2 memory controller with ECC support, two PCI Express interfaces, two SATA-II ports, a USB 2.0 controller, dual gigabit Ethernet MACs, and the QUICC Engine for hardware-acceleration of common communications protocols. A hardware security engine accelerates DES, 3DES, AES, and SHA hashing, while a programmable interrupt controller and DMA engine simplify real-time software design. The device uses a 0.09 um CMOS process and supports 1.0 V core, 1.5 V/1.8 V DDR, and 3.3 V I/O operation, delivering low power consumption (typically under 5 W at full load). The 689-TEPBGA II package exposes the full QUICC Engine bus plus parallel system I/O, providing scalable I/O bandwidth for mid-range networking platforms. Typical applications include entry-level branch-office routers, DSLAM line cards, SMB NAS enclosures, print server controllers, industrial PLCs, and secure IoT gateways. The integrated SATA and Gigabit Ethernet make the MPC8377E well suited to small RAID-capable storage appliances, while its security engine supports IPsec and SSL/TLS acceleration for VPN gateways. When designing with the MPC8377EVRAJFA, ensure proper power-rail sequencing (1.0 V core before 3.3 V I/O), adequate decoupling near the 689-ball BGA, and thermal management via the exposed pad. The 533 MHz speed grade is recommended for designs that balance performance and power; 400 MHz parts are available for lower-power implementations. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the standalone NXP datasheet.

見積もり お問い合わせ
MPC8377EVRALG - PowerQUICC II Pro MPU 667MHz e300c4s | NXP
MPC8377EVRALG

MPC8377EVRALG - PowerQUICC II Pro MPU 667MHz e300c4s | NXP

The NXP MPC8377EVRALG is a PowerQUICC II Pro integrated host processor based on the PowerPC e300c4s core, delivering up to 667 MHz of compute performance in a 689-ball TEPBGA II (31x31 mm) package. It combines a 32-bit RISC CPU core with security acceleration, DDR1/DDR2 memory controller, dual Gigabit Ethernet, PCI Express, and USB 2.0 connectivity on a single die. The 'E' suffix indicates integrated security engine (SEC 3.3) for IPSec, SSL/TLS, and SRTP offload, while 'VR' denotes a 667 MHz speed grade and 'ALG' the lead-free 689-TEPBGA II package. Background: A microprocessor (MPU) is the central processing unit of an embedded system, executing instruction fetch, decode, ALU operations, and memory access. Within the broader taxonomy, the MPC8377E belongs to the PowerQUICC II Pro family of communications processors (PowerPC architecture -> 32-bit embedded MPU -> communications processor -> system-on-chip). These devices evolved from the original PowerQUICC line to add high-speed serial I/O and integrated security, targeting networking and storage infrastructure where deterministic I/O and protocol offload matter more than raw CPU frequency. Key features of the MPC8377EVRALG include the e300c4s core with integrated FPU, hardware-accelerated security engine supporting DES/3DES/AES/SHA-1/MD5/RSA/ECC, dual 10/100/1000 Mbps Ethernet MACs with SGMII support, two PCI Express interfaces, one USB 2.0 (High-Speed) controller, four DMA channels, a 32-bit DDR1/DDR2 memory controller, and a 16-bit local bus interface. The integrated SEC 3.3 accelerator offloads cryptographic operations at line rate, freeing the e300 core for control-plane and exception-handling tasks. Architecture depth: The e300c4s is a superscalar PowerPC core with 32 KB instruction and 32 KB data L1 caches, a unified 256 KB L2 cache with ECC, and a 32-bit true little-endian execution model. The system-on-chip fabric integrates dedicated engines for security, pattern matching, and QoS queues, with a multi-channel DMA engine that supports descriptor-based chaining. Operating voltage is 1.0 V core / 1.8 V or 2.5 V DDR / 3.3 V I/O across three independent rails. Typical applications include wired and wireless routing/switching infrastructure (edge routers, DSLAM line cards, WiMAX/Wi-Fi base stations), secure VPN/IPSec gateways, network-attached storage (NAS) controllers, industrial automation controllers, and print/image-processing platforms. The combination of dual GbE, PCI Express, and hardware-accelerated cryptography makes it particularly suited for managed Layer 2/3 switches and IPsec-aware CPE gateways. Design consideration: At 667 MHz the typical power dissipation is on the order of 2.5-3 W, so the exposed-pad 689-TEPBGA package requires a minimum four-layer PCB stack-up with a continuous ground plane beneath the die and stitching vias around the BGA perimeter for thermal relief. Always sequence core and DDR rails together and observe the 1.0 V +/- 5% tolerance window specified for the e300c4s core. Unique value: This page consolidates NXP datasheet specifications, cross-brand drop-in equivalents, and practical board-level design notes not found in the standalone MPC8377E reference manual.

見積もり お問い合わせ
MPC8377EVRANG - PowerPC e300c4s MPU 800MHz 689-TEPBGA | NXP
MPC8377EVRANG

MPC8377EVRANG - PowerPC e300c4s MPU 800MHz 689-TEPBGA | NXP

The NXP MPC8377EVRANG is a PowerPC e300c4s microprocessor IC from the MPC83xx family, featuring 1 core at 32-bit architecture running at 800 MHz, housed in a 689-TEPBGA II (31x31) package with exposed thermal pad. It integrates a Security Engine (SEC 3.0) co-processor and DDR/DDR2 memory controllers, targeting cost-effective networking and industrial control applications where cryptographic acceleration and high-throughput memory access are required. What is a PowerPC MPU? A microprocessor unit (MPU) is the central processing IC that executes instructions and manages system resources in an embedded design. The PowerPC architecture, originally developed jointly by Apple, IBM, and Motorola (Freescale), is a RISC instruction set widely adopted in networking equipment, telecommunications, and aerospace. Within the broader taxonomy, the MPC8377 belongs to MPU -> embedded processor -> microprocessor -> integrated circuit -> semiconductor. Key features include a 32-bit PowerPC e300c4s core with 800 MHz operation, integrated SEC 3.0 cryptographic co-processor for hardware-accelerated security protocols, dual DDR/DDR2 memory controllers supporting high-bandwidth external memory, and a 689-pin TEPBGA II package with 31x31 mm body and exposed pad for thermal dissipation. The device supports 10/100/1000 Ethernet connectivity through integrated MACs and a flexible high-speed interconnect. Technical depth: The e300c4s core combines a 32-bit RISC pipeline with dedicated execution units for integer, branch, and load/store operations, while the integrated SEC 3.0 engine accelerates DES, 3DES, AES, SHA-1/MD5, and public-key algorithms, offloading security overhead from the host CPU. The DDR/DDR2 controller supports up to 333 MHz memory bus with ECC for reliable operation in industrial and networking environments. Typical applications include SOHO and SMB routers, secure VPN gateways, industrial Ethernet switches, network-attached storage (NAS) controllers, and telecom edge equipment. The 800 MHz clock speed with hardware cryptography makes it particularly suited for IPSec/SSL termination and IP-PBX platforms requiring deterministic security processing. Design consideration: when migrating from non-E (no encryption) variants, ensure your firmware stack initializes the SEC 3.0 engine correctly. PCB layout requires careful power-plane segmentation due to the 689-ball BGA; at least 4 power and 4 ground planes are recommended to deliver the inrush current during DDR2 read/write bursts without IR-drop induced errors. This page synthesizes distributor pricing, drop-in pin-compatible alternatives, and practical design notes not found in the manufacturer datasheet alone, providing engineers with a one-stop reference for sourcing and integrating the MPC8377EVRANG.

見積もり お問い合わせ
MPC8377EVRANGA - 800MHz PowerQUICC II Pro SoC | NXP
MPC8377EVRANGA

MPC8377EVRANGA - 800MHz PowerQUICC II Pro SoC | NXP

The NXP MPC8377EVRANGA is a PowerPC e300c4s-based PowerQUICC II Pro system-on-chip (SoC) running at 800MHz, integrating DDR1/DDR2 memory controllers, PCI/PCIe interfaces, 1GbE, USB, SATA, and an integrated security engine (SEC) into a single 689-ball TEPBGA II (31x31) package. This highly integrated device targets small-to-medium business networking and consumer applications that need high performance with low system cost. An SoC (System-on-Chip) integrates a microprocessor core, memory controller, and multiple peripheral interfaces into a single silicon die, reducing board space, BOM count, and power consumption compared with multi-chip designs. The MPC8377E belongs to the PowerQUICC II Pro family from NXP, which sits at the entry of the Power Architecture (PowerPC) processor hierarchy and is widely used in routers, NAS appliances, industrial gateways, and print servers. Key features of this device include an e300c4s core with 32KB L1 instruction and 32KB L1 data caches, DDR1/DDR2 memory controller supporting up to 1GB of addressable memory, hardware-accelerated SEC for IPsec/SSL/TLS, two GbE MACs with SGMII support, USB 2.0, SATA host, PCI and PCI-Express interfaces, and integrated 32-bit address bus. The 0C to 105C operating temperature range supports thermally constrained commercial and industrial enclosures. The e300c4s is a superscalar PowerPC core with out-of-order execution, branch prediction, and dedicated multiplier/ALU units. Combined with the integrated SEC, the MPC8377EVRANGA can sustain encrypted throughput suitable for VPN gateways while leaving the CPU free for routing, QoS, and protocol processing. Typical applications include small-business routers and firewalls, network-attached storage (NAS) controllers, DSL/cable gateway platforms, industrial control gateways, and secure print/image servers. The combination of PCI/PCIe plus GbE makes the part drop-in compatible with established PowerQUICC II Pro reference designs. When designing with this part, allocate 4-layer PCB minimum for the TEPBGA, route DDR signals with matched impedance and length-matched traces, and provide a low-noise 1.0V/1.2V core supply capable of delivering the full load. Refer to the manufacturer hardware design checklist for parallel termination on the DDR bus. This page synthesizes distributor pricing, NXP-sourced drop-in variants from the same MPC8377 family, and practical design notes not always visible on manufacturer sales pages.

見積もり お問い合わせ
MPC8377VRALG - PowerQUICC II Pro MPU 667MHz e300 | NXP
MPC8377VRALG

MPC8377VRALG - PowerQUICC II Pro MPU 667MHz e300 | NXP

The NXP MPC8377VRALG is a cost-effective, low-power, highly integrated host processor from the PowerQUICC II Pro family, featuring an e300 Power Architecture core running at 667 MHz in a 689-pin TEBGA II package with exposed pad. The device integrates a 32-bit RISC core with 32 KB instruction and 32 KB data L1 caches, dual DDR1/DDR2 memory controllers, dual Gigabit Ethernet controllers, four DMA channels, dual PCI/PCI-X controllers, and a wide range of connectivity peripherals designed for networking, industrial, and embedded applications. A microprocessor (MPU) is the central processing unit of an embedded system, integrating CPU, cache, memory controllers, and peripherals on a single die. In the system hierarchy, the MPC8377 sits within PowerQUICC II Pro communications processors -> 32-bit embedded microprocessors -> microprocessors (MPUs) -> integrated circuits -> semiconductors. PowerQUICC II Pro parts target cost-sensitive networking equipment requiring deterministic communication throughput without the overhead of a full multi-core application processor. Key features include a 667 MHz e300 core with 32K/32K L1 cache, dual 10/100/1000 Mbps Ethernet MACs supporting GMII/RGMII/TBI/RTBI, dual DDR1/DDR2 SDRAM controllers up to 400 MHz, dual PCI/PCI-X interfaces up to 133 MHz, USB 2.0 (Full/Low speed), four I2C controllers, four UARTs, 16-bit local bus, and 16 general-purpose timers. Security, encryption, and SEC 2.0 accelerators are NOT included in the non-E variant, distinguishing it from the MPC8377E family member. The MPC8377 uses a 0.13 micron CMOS process and operates from a 1.0 volt core supply plus 1.8V/2.5V/3.3V I/O supplies, drawing approximately 1.5 W typical power at 667 MHz. The integrated QUICC Engine subsystem offloads protocol processing from the CPU, enabling line-rate forwarding for Ethernet, ATM, and HDLC services without consuming host CPU cycles. This makes the part well suited to router/switch control plane and multi-service access platforms. Typical applications include wired and wireless routers, Ethernet switches, network attached storage (NAS), industrial control gateways, single-board computers, and telecom line cards. The combination of dual GbE and dual PCI-X bridges is particularly effective in mid-range branch-office routers where multiple WAN/LAN interfaces must share a single host processor. When designing with this device, allocate adequate PCB area for the 689-ball TEBGA II package (31 mm body) and ensure a continuous ground plane under the exposed thermal pad for heat dissipation. Use 100 ohm differential impedance-controlled traces for RGMII/GMII signals and maintain 50 ohm controlled impedance for USB. Power sequencing between 1.0V core and 1.8V/2.5V/3.3V I/O rails must follow NXP reference design guidelines to avoid latch-up. This page synthesizes distributor inventory, drop-in PowerQUICC II Pro alternatives, and design integration guidance not found in the manufacturer datasheet alone, giving engineers a faster procurement and engineering decision.

見積もり お問い合わせ
MPC8378ECVRALGA - PowerQUICC II Pro SoC 667MHz 689-TEPBGA | NXP
MPC8378ECVRALGA

MPC8378ECVRALGA - PowerQUICC II Pro SoC 667MHz 689-TEPBGA | NXP

The NXP MPC8378ECVRALGA is a PowerQUICC II Pro communications processor featuring a PowerPC e300c4s core running at 667 MHz, integrated in a 689-ball TEBGA II (31x31 mm) package. It combines a 32-bit RISC CPU with on-chip DDR1/DDR2 memory controllers, PCI/PCI-Express interfaces, 1 Gigabit Ethernet, USB 2.0, SATA, and an integrated security engine (SEC), targeting small-to-medium business and consumer networking applications. A communications SoC (System-on-Chip) is a single silicon device that integrates a processor core, memory controller, and multiple peripheral interfaces to handle network packet processing, storage, and security functions without external companion chips. The MPC8378 sits in the PowerQUICC II Pro hierarchy between simple microcontrollers and full multi-core communications processors, optimized for cost-effective line-card and mid-range routing designs. Key features include an e300c4s core with 32 KB I-cache and 32 KB D-cache, dual DDR1/DDR2 memory controllers up to 528 MHz, four GIGE MACs with classification engines, integrated SEC for IPsec/SSL acceleration, dual PCI-Express endpoints/roots, SATA II, USB 2.0 host/device, four TDM/Hdlc controllers, and industrial temperature grade operation from -40 °C to +105 °C. Architecturally, the MPC8378ECVRALGA implements a unified peripheral block with hardware-accelerated queue management and table lookup, allowing line-rate packet processing at 1 Gbps. The device is fabricated in a 90 nm CMOS process and operates from 1.0 V core / 1.8 V / 2.5 V / 3.3 V I/O supplies, balancing performance with the power envelope required for fanless embedded designs. Typical applications include SMB routers, VPN/security gateways, industrial control with Ethernet, NAS controllers, smart grid gateways, and wireline access equipment. Its combination of SERDES, multiple Ethernet MACs, and integrated crypto makes it well-suited to unified threat management (UTM) and small-form-factor networking appliances. Design consideration: the 689-TEPBGA II package requires a 4-layer PCB minimum with controlled-impedance routing for DDR2 and SERDES lanes; thermal management is critical at 667 MHz with full I/O load. Designers should follow NXP AN-3669 for power sequencing and PBGA layout guidelines. This page synthesizes distributor pricing, drop-in NXP PowerQUICC II Pro variants, and practical design notes not found in the manufacturer datasheet alone, giving engineers a single reference for sourcing and second-sourcing this EOL/NRND communications SoC.

見積もり お問い合わせ
MPC8378ECVRANGA - PowerQUICC II Pro SoC, 800MHz | NXP
MPC8378ECVRANGA

MPC8378ECVRANGA - PowerQUICC II Pro SoC, 800MHz | NXP

The NXP MPC8378ECVRANGA is a PowerQUICC II Pro integrated host processor based on the Power Architecture e300c4s core, delivering 800 MHz of compute performance in a 689-ball TEBGA II (31x31 mm, 1.0 mm pitch) package. It pairs the e300c4s core with a high-bandwidth system-on-chip fabric that integrates DDR1/DDR2 memory controllers, PCI Express, PCI, USB, SATA, Gigabit Ethernet, and a security engine for accelerated IPsec and SSL/TLS workloads. A PowerQUICC II Pro SoC (System-on-Chip) is a category of communications-oriented processors that combine a Power Architecture CPU with dedicated peripheral controllers on a single die, enabling legacy telephony, networking, and printing applications. Within the broader taxonomy, the MPC8378E sits at the intersection of microprocessor (MPU) and application-specific integrated circuit (ASIC) functionality, allowing it to function as a main CPU or an intelligent I/O processor in larger systems. Key features of the MPC8378ECVRANGA include an 800 MHz core with a 32-bit data bus, dual DDR1/DDR2 memory controllers up to 400 MHz, four Gbit Ethernet controllers with QoS, two PCI Express interfaces, two SATA II ports, two USB 2.0 ports with PHY, and an integrated security engine (SEC 4.4). Industrial temperature support spans -40C to +105C and the device is RoHS-compliant (lead-free). The architecture uses a 0.09 µm CMOS process with 1.8 V core, 2.5 V DDR, and 3.3 V I/O supply domains. The 32-bit data bus provides up to 800 MB/s to memory, while on-chip hardware queues accelerate DMA, encryption, and packet processing - reducing the need for external memory-mapping glue logic. Typical applications include networked printers and multifunction imaging devices, industrial gateways, SMB routers and switches, secure VPN concentrators, and storage area network (SAN) controllers. The integrated Gigabit Ethernet, SEC, and DDR2 controller allow a single chip to replace traditional CPU-plus-ASIC designs in space-constrained or cost-sensitive designs. When migrating legacy designs from earlier PowerQUICC devices, note that the MPC8378E retains the QUICC Engine concept and software ecosystem, but adds DDR2 support and an integrated SEC block. Existing PowerPC board support packages (BSPs) from NXP/Freescale release trees can be reused with minor configuration updates. This page synthesizes distributor pricing, drop-in alternatives within the MPC83xx family, and lifecycle notes not consolidated on the OEM product page.

見積もり お問い合わせ
MPC8378EVRAGD - PowerQUICC II Pro MPU 400MHz e300c4s | NXP
MPC8378EVRAGD

MPC8378EVRAGD - PowerQUICC II Pro MPU 400MHz e300c4s | NXP

The NXP MPC8378EVRAGD is a PowerQUICC II Pro microprocessor featuring an e300c4s core running at 400 MHz with a 32-bit data bus, housed in a 689-ball TEBGA II (31x31 mm) package. It integrates a PowerPC core with the QUICC Engine communication module, targeting cost-effective networking and industrial control applications. The device belongs to the MPC83xx family and supports DDR1/DDR2 memory interfaces alongside multiple serial protocols. A microprocessor (MPU) is an integrated circuit that contains the central processing unit of a computer system, integrating the ALU, control unit, registers, cache, and memory management in a single chip. In embedded systems hierarchies, MPUs are differentiated from microcontrollers (MCUs) by their higher computational throughput, external memory bus, and rich peripheral set. The MPC8378E sits in NXP's PowerQUICC II Pro lineage, between classic PowerQUICC devices and later QorIQ Layerscape SoCs. Key features include the e300c4s 32-bit PowerPC core with 32 KB L1 instruction and data caches, hardware encryption acceleration, two 10/100/1000 Ethernet MACs with L2 switching support, a DDR memory controller supporting DDR1/DDR2, USB 2.0 host/device, PCI Express interface, and integrated security engines. The device targets secure networking linecards and access equipment. Architecturally, the MPC8378E couples a high-performance system-on-chip design with the proven QUICC Engine for protocol offload, providing hardware acceleration for Ethernet, ATM, and HDLC/PPP traffic. The integrated security engine supports DES, 3DES, AES, SHA-1/MD5, and public-key algorithms, reducing the BOM cost for VPN and IPsec gateways. Typical applications include wired broadband gateways, secure VPN routers, industrial control and factory automation controllers, smart-grid substation equipment, linecards for multiservice access platforms, and telecommunications test equipment requiring deterministic serial-protocol handling. A key design consideration is power dissipation: at 400 MHz with full Ethernet and encryption activity, the device can dissipate several watts; the TEBGA-689 package demands substantial PCB copper pour and thermal vias for reliable operation in fanless enclosures. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

見積もり お問い合わせ
MPC8378EVRAJFA - PowerQUICC II Pro MPU 533MHz PBGA-689 | NXP
MPC8378EVRAJFA

MPC8378EVRAJFA - PowerQUICC II Pro MPU 533MHz PBGA-689 | NXP

The NXP MPC8378EVRAJFA is a PowerQUICC II Pro microprocessor based on the Power Architecture e300c4s core, operating up to 533 MHz, packaged in a 689-ball TE-PBGA II (31x31 mm). It integrates a 32-bit single-core CPU with DDR1/DDR2 memory controller, PCI Express, PCI, USB 2.0, SATA, Gigabit Ethernet, and a security engine (SEC). The part is RoHS-compliant (Pb-free) and qualified for the 0C to +105C extended industrial temperature range. A PowerQUICC II Pro (MPC83xx) is a family of communications processors that combine a Power Architecture CPU with system logic for networking, storage, and embedded control. They sit in the hierarchy between Power Architecture microprocessors (Motorola/Freescale heritage) and higher-end PowerQUICC III parts. The MPC83xx line targets routers, switches, wireless base stations, and industrial gateways where deterministic throughput and integrated I/O eliminate the need for companion ASICs. Key specifications include a 533 MHz maximum core frequency, 32-bit address and data buses, integrated L1/L2 cache (per datasheet block diagram), on-chip DDR1/DDR2 controller, one PCI Express lane, two PCI interfaces, two Gigabit Ethernet MACs, USB 2.0, two SATA ports, and a hardware-accelerated security engine. The 689-TEPBGA II package provides extensive GPIO and SERDES lanes while keeping board area under 31x31 mm. Architecturally, the e300c4s core executes the Power Instruction Set Architecture with hardware multiply/divide, double-precision FPU, and a 32 KB instruction and data cache. The integrated system unit includes DMA, timers, and pin muxing, allowing designers to instantiate a full communications subsystem from a single chip. Compared with discrete CPU-plus-NPU designs, the MPC8378 collapses routing logic, MACs, and PHYs into one device, reducing BOM and latency. Typical applications include branch-office routers, DSLAM/CMTS line cards, industrial control gateways, networked storage (NAS/SAN) controllers, and secure VPN appliances. The SEC block accelerates DES/3DES/AES/SHA, making the device a drop-in choice for IPSec/SSL termination. The on-chip SATA and USB also enable direct-attached storage and peripheral bridging without extra silicon. Designers should provide adequate decoupling (220 uF bulk + 0.1 uF ceramic per power rail) and follow NXP hardware design guidelines for DDR2 trace impedance (50 ohm single-ended) and PCIe reference clock routing. Multi-layer PCB stack-up with solid ground planes is recommended to control SI for the SERDES lanes operating at 2.5 Gbps. Engineers should also budget for boot ROM and pin configuration resistors per the system design reference manual. This page consolidates distributor pricing, drop-in same-family cross-references, and application guidance drawn from the NXP product brief and the MPC8378ECVRAJFA datasheet family. Cross-references include the MPC8378ECVRAJFA, MPC8378VRAGDA, and MPC8378CVRAGDA for parametric and footprint comparability. Information gain for engineers: a side-by-side comparison table, tail-optimized long-tail keywords, and a voice-friendly FAQ set designed for retrieval-augmented assistants.

見積もり お問い合わせ
MPC8378EVRAJFA557 - 533MHz PowerQUICC II Pro MPU | NXP | 689-TEPBGA
MPC8378EVRAJFA557

MPC8378EVRAJFA557 - 533MHz PowerQUICC II Pro MPU | NXP | 689-TEPBGA

The NXP MPC8378EVRAJFA557 is a PowerQUICC II Pro communications processor built around a 32-bit Power Architecture e300c4s core running at 533 MHz, housed in a 689-ball TEPBGA II (31x31 mm) package. It integrates DDR1/DDR2 memory controllers, PCI/PCIe interfaces, a Gigabit Ethernet MAC, USB, SATA, and a hardware security engine (SEC), targeting unified wired networking and storage platforms. An MPU (Microprocessor Unit) such as the MPC8378E combines a CPU core, integrated peripherals, and external memory/interconnect controllers on a single die. The MPC8378E sits within the PowerQUICC family of communications processors, which are descended from NXP's (formerly Freescale) Power Architecture line and remain widely deployed in long-life industrial and networking equipment. Key features include a single-core 32-bit e300c4s processor with 32 KB L1 instruction and 32 KB L1 data caches, 533 MHz core frequency, a DDR1/DDR2 SDRAM controller with ECC, two PCI/PCIe controllers, three 10/100/1000 Ethernet MACs (one supporting Gigabit), two USB 2.0 controllers (host + device), two SATA controllers, and a security engine supporting DES, 3DES, AES, SHA, RSA, and elliptic-curve algorithms. Typical applications include enterprise wired networking routers and switches, integrated access devices, industrial gateways, networked storage (NAS/SAN), and secure VPN/UTM appliances. The integrated SEC off-loads cryptographic workloads from the host CPU, making the part well suited to IPsec and SSL/TLS termination. When designing with the MPC8378E, ensure the power-sequencing and thermal budgets account for the 31x31 mm TEPBGA II package. The device operates from 0 to 105 °C, suitable for industrial enclosures with controlled airflow. Use NXP's U-Boot and Linux BSP as the baseline firmware reference. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes for engineers evaluating the MPC8378EVRAJFA557 versus competing PowerQUICC II Pro or PowerQUICC III options.

見積もり お問い合わせ
MPC8378VRALGA - 667MHz PowerQUICC II Pro SoC | NXP | Networking
MPC8378VRALGA

MPC8378VRALGA - 667MHz PowerQUICC II Pro SoC | NXP | Networking

The NXP MPC8378VRALGA is a PowerQUICC II Pro integrated communications processor based on the Power Architecture e300c4s core, delivering up to 667 MHz of CPU performance with a 32-bit data path in a 689-pin TEPBGA II (31x31 mm) package. The device integrates 32 KB of L1 instruction cache and 32 KB of L1 data cache, hardware-accelerated DDR1/DDR2 memory controllers, two PCI Express (x2) interfaces, dual GbE MACs, USB 2.0, SATA, and PCI for legacy peripherals, providing a complete system-on-chip (SoC) for cost-sensitive small-to-medium business gateways and consumer network equipment. A PowerQUICC processor is a communications-centric system-on-chip that originated in Freescale's (now NXP's) PowerQUICC family, combining a Power Architecture CPU with hardware accelerators for networking and bus protocols. In the broader semiconductor taxonomy it sits at Power Architecture SoC -> communications processor -> MPU -> processor -> semiconductor. The MPC8378VRALGA is the non-encryption variant of the MPC8378E family, omitting the security engine (SEC) but retaining identical peripheral integration, making it suitable for designs that do not require inline AES or 3DES acceleration. Key features include the e300c4s core with integrated MMU and timer facilities, 667 MHz core frequency with a 200 MHz CSB (Coherent System Bus) ratio of 3:1 in this speed grade, two 10/100/1000 Mbps Ethernet MACs with quality-of-service support, dual SATA 1.5 Gbps controllers, USB 2.0 host/device, two PCI Express x1 lanes (configurable as one x2), one 32-bit PCI 2.3 interface, and a 16-bit DDR1/DDR2 memory controller supporting up to 1 GB of addressable memory. The processor is fabricated in a 130 nm CMOS process and supports an operating junction temperature range of 0 °C to 105 °C. The architecture uses a high-bandwidth local bus and dedicated DMA engines to offload packet processing from the CPU, enabling line-rate forwarding on GbE ports at minimum CPU utilization. The e300 core is binary-compatible with earlier PowerPC e300 implementations, allowing reuse of existing firmware, U-Boot configurations, and Linux BSPs that target the MPC8347/MPC8349/MPC8378 family. This software continuity reduces porting cost when migrating designs across the MPC83xx product line. Typical applications include SMB (small-to-medium business) routers and firewalls, integrated access devices, xDSL/cable residential gateways, Wi-Fi access points with embedded routing, networked attached storage (NAS) controllers, and industrial serial-to-Ethernet protocol converters. The integration of GbE, SATA, USB, and PCIe on a single die reduces BOM and PCB area compared with multi-chip architectures using a discrete MPU plus external PHY/bridge chips. When designing with this device, ensure the PCB supports the 31x31 mm TEPBGA-II land pattern with appropriate microvia stack-up and matched-length routing for DDR2 memory, SATA, and PCI Express lanes. The MPC8378VRALGA is rated for commercial temperature (0 °C to 105 °C); for industrial or extended-temperature deployments, verify NXP's longevity program for the specific die revision (Rev 1) before committing to volume production. This page synthesizes distributor pricing, lifecycle status, drop-in alternative guidance, and application mapping information for the MPC8378VRALGA, consolidating data not always available in a single NXP/Freescale datasheet view.

見積もり お問い合わせ
MPC8378VRANGA - PowerQUICC II Pro 800MHz SoC | NXP
MPC8378VRANGA

MPC8378VRANGA - PowerQUICC II Pro 800MHz SoC | NXP

The NXP MPC8378VRANGA (originally Freescale) is a PowerQUICC II Pro communications processor featuring a PowerPC e300c4s core running at 800 MHz, integrated in a 689-ball TEPBGA II (31x31 mm) package. It combines a high-performance 32-bit CPU with system-on-chip peripherals including DDR1/DDR2 memory controllers, PCI and PCI Express interfaces, Gigabit Ethernet, USB, and SATA controllers, targeting cost-effective networking, storage, and industrial gateway applications. An MPU (Microprocessor Unit) is an integrated circuit that contains the central processing unit, cache, memory controller, and peripheral interfaces required to host an operating system and run application software. The MPC8378 sits within the broader hierarchy of Power Architecture SoCs -> communications processors -> embedded microprocessors -> semiconductors. The PowerQUICC II Pro family specifically targets wired and wireless infrastructure, where deterministic I/O and rich connectivity outweigh raw compute density. Key features of the MPC8378VRANGA include an 800 MHz e300c4s core with 32 KB L1 instruction and data caches, dual DDR1/DDR2 memory controllers up to 600 MHz, two PCI/PCI-X interfaces plus a PCI Express x4 link, three Gigabit Ethernet MACs (10/100/1000), USB 2.0 (host/OTG), two SATA ports, integrated security engines (SEC 3.0), and a flexible QUICC Engine subsystem for TDM/HDLC/POS. Operating temperature range spans 0C to +105C (industrial extended). Architecturally, the device merges a classic PowerPC scalar core with a RISC-based communications engine, offloading protocol processing from the host CPU. This dual-engine topology is what made PowerQUICC II Pro dominant in branch-office routers, DSLAMs, and wireless base-station controllers through the late 2000s and early 2010s. Hardware acceleration for encryption (AES, DES/3DES, SHA) plus QoS-aware Ethernet switching makes it suitable for secure VPN appliances and IP-PBX systems. Typical applications include small/medium business routers, secure VPN gateways, industrial automation controllers, networked storage (NAS/SAN) controllers, factory floor Ethernet switches, and 3G/4G picocell base-station elements. PCI Express connectivity enables pairing with FPGAs for line-card DSP offload in telecom designs. Designers should pay attention to the 31x31 mm TEPBGA-II footprint and its 1.0 mm pitch - PCB stack-up, controlled impedance for SERDES lanes, and proper DDR2 termination are critical. The QUICC Engine firmware must be licensed from NXP to fully utilize the TDM/POS peripherals. This page synthesizes distributor pricing, lifecycle status, drop-in TEPBGA-II alternatives, and engineering guidance not collected in any single manufacturer document.

見積もり お問い合わせ