マイクロコントローラ

製品 (20,000+)

P5021NXE7TMC - QorIQ Dual-Core 1.8GHz SoC | NXP Semiconductors
P5021NXE7TMC

P5021NXE7TMC - QorIQ Dual-Core 1.8GHz SoC | NXP Semiconductors

The NXP QorIQ P5021NXE7TMC is a 64-bit dual-core Power Architecture system-on-chip (SoC) that integrates two e5500 cores running at up to 1.8 GHz, a tightly-coupled cache hierarchy, hardware-accelerated data paths, and a rich set of networking and peripheral interfaces for embedded compute-intensive applications. It ships in a 1295-pin FCPBGA package (37.5 x 37.5 mm) rated for the industrial extended temperature range of -40C to +105C and targets networking, telecom/datacom, wireless infrastructure, and aerospace/military designs. A QorIQ P5 family device is a 64-bit Power Architecture (formerly PowerPC) communications processor that combines general-purpose cores with integrated networking peripherals (Ethernet, PCIe, SATA, USB, SerDes) and a hardware security engine. The P5 family sits in NXP's broader QorIQ communications processor hierarchy between the entry-level P1/P3 families and the high-end P4080/T series. The dual-core P5021 occupies a middle position in this family, sharing software and pinout compatibility with the quad-core P5040, the single-core P5010, and the dual-core P5020, allowing a single PCB to scale from one to four cores simply by swapping the BGA. Key features of the P5021NXE7TMC include dual e5500 cores at 1.8 GHz, support for DDR3 / DDR3L memory with ECC, integrated 1/10 Gigabit Ethernet MACs, multiple PCI Express Gen2 controllers, SATA 2.0, USB 2.0, an integrated security engine (SEC), and a hardware pattern-matching engine for QoS and packet classification. The 1.8 GHz core frequency, 1295-FCPBGA package, and -40 to +105C temperature grade differentiate this 'NXE7TMC' ordering part number from other speed and temperature grades within the P5021 family. Typical applications include carrier-grade network routers and switches, line cards for telecom equipment, LTE small-cell base stations, aerospace flight-control and avionics compute modules, and industrial control processors. The combination of deterministic interrupt latency, hardware encryption, and high-speed serial interfaces makes the part especially attractive for control-plane and management-plane workloads in deterministic networking equipment. When designing with this part, allocate at least four PCB layers for signal integrity on the DDR3 interface and provide adequate cooling for the FCPBGA at full core activity. Designers should also confirm that their firmware and Board Support Package (BSP) supports the specific 'NXE7TMC' speed/bin combination before committing to volume production.

見積もり お問い合わせ
P5040NSE72QC - QorIQ P5 4-Core 2.2GHz SoC | NXP | Networking
P5040NSE72QC

P5040NSE72QC - QorIQ P5 4-Core 2.2GHz SoC | NXP | Networking

The NXP P5040NSE72QC is a QorIQ P5 series communications processor SoC integrating four single-threaded e5500 cores built on Power Architecture v2.06 technology, clocked up to 2.2 GHz, in a 1295-ball FCBGA (37.5 mm x 37.5 mm) package. The device targets high-performance networking applications such as control plane processing, service routers, and enterprise switching platforms. A communications SoC (System-on-Chip) is a highly-integrated processor that combines CPU cores, memory controllers, high-speed serial interfaces, and platform peripherals on a single die. Within the broader taxonomy, the P5040 belongs to: microprocessor -> multicore SoC -> networking SoC -> embedded communications processor -> semiconductor. The e5500 core implements the Power Architecture v2.06 64-bit ISA with hardware hypervisor support and three levels of instruction privilege (user, supervisor, hypervisor), enabling workload isolation in virtualized network functions. Key features of the P5040NSE72QC include 4 e5500 cores at 2.2 GHz, integrated DDR3/DDR3L controller with ECC support up to DDR3-2133, multiple PCIe controllers, 1/10 Gigabit Ethernet MACs, SATA interfaces, and a SEC (Security Engine) for cryptographic offload. The device supports up to ten 1 GbE ports or combinations of 1G/10G, plus a 64-bit DDR3/3L memory interface with ECC. Operating temperature range is 0C to 90C, suitable for commercial and industrial networking environments with controlled airflow. The P5040 architecture uses a hierarchical interconnect with CoreNet coherency fabric linking cores, memory controller, and platform blocks. This allows snoop-based cache coherence across the four cores and deterministic memory access latency, which is critical for packet processing workloads. The SEC 5.x block accelerates AES, 3DES, SHA, RSA, and ECC operations, offloading IPsec and TLS tunnels from the cores. Typical applications include service provider routers, multi-service gateways, enterprise access switches, wireless base station controllers, and network-attached storage (NAS) controllers. The combination of high core count, integrated 10G Ethernet, and on-chip SEC makes the P5040NSE72QC particularly well-suited for line-rate control-plane and security processing at line rates up to multi-10G. When designing with the P5040, ensure the FCBGA thermal solution is rated for the 0-90C junction range, route all high-speed SerDes lanes with reference-impedance-controlled PCB stackups (100 ohm differential for 10G, 85 ohm for PCIe), and validate DDR3/3L fly-by topology against the JEDEC specifications referenced in the device errata. This page synthesizes NXP product-page specifications, distributor pricing from DigiKey/Mouser/Octopart, and engineering cross-reference data not found in any single source. It is intended as a decision-support companion to the NXP QorIQ P5040 hardware reference manual.

見積もり お問い合わせ
P5040NSN12QB - QorIQ P5 4-Core 2.2GHz SoC | NXP Semiconductors
P5040NSN12QB

P5040NSN12QB - QorIQ P5 4-Core 2.2GHz SoC | NXP Semiconductors

The NXP Semiconductors (formerly Freescale) P5040NSN12QB is a quad-core 64-bit QorIQ P5 communications SoC delivering up to 2.2 GHz per core, packaged in a 1295-ball HBGA and qualified over the 0C to 105C industrial temperature range. The device integrates four e5500 Power Architecture cores with a tightly coupled cache hierarchy (512 KB L2 per core with ECC), hardware-accelerated packet processing, and a high-speed I/O subsystem including DDR3/3L controllers, multiple PCIe Gen2 controllers, 1/10 GbE interfaces, SATA, and USB. A QorIQ communications processor is a system-on-chip (SoC) designed for high-performance networking and embedded infrastructure. QorIQ belongs to the broader category of microprocessors -> application processors -> communications SoCs. The P5 family is engineered for power-efficient multi-core processing, supporting both single-, dual-, and quad-core scaling to address workloads ranging from mid-range branch routers to high-end control-plane aggregation. This SoC class is foundational for routers, switches, wireless base stations, and aerospace/defense systems where deterministic throughput and protocol offload matter. Key specifications include four e5500 cores at up to 2.2 GHz, 512 KB L2 cache per core with ECC, a 64-bit DDR3/3L memory controller with ECC, integrated 10 Gigabit Ethernet MACs, PCIe Gen2 controllers, SATA 2.0, USB 2.0, and secure boot. The 1295-ball HBGA package offers robust thermal dissipation for sustained performance under fanless or limited-cooling chassis. Operating temperature range of 0C to 105C supports industrial and extended-temperature deployments. Architecturally, the P5040 implements the e5500 core with out-of-order execution, hardware virtualization support, and dedicated datapath engines. The integrated Data Path Acceleration Architecture (DPAA) offloads packet classification, queue management, and cryptographic operations, freeing the cores for control-plane workloads. The combination of multi-core throughput and integrated I/O reduces system BOM cost by eliminating companion chipsets. Typical applications include enterprise and carrier-grade routers, LTE/4G wireless base stations, network-attached storage (NAS) controllers, IP-PBX platforms, and aerospace/defense embedded computing. It is also used in industrial control systems and security appliances where deterministic multi-core performance is required. When designing with the P5040NSN12QB, allocate ample PCB area for the 1295-ball HBGA land pattern, use controlled-impedance routing for high-speed serial links (10 GbE, PCIe, SATA), and provide adequate power decoupling per NXP hardware design guidelines. Reference the NXP QorIQ P5040 reference design (Rev 2.0) for schematic, layout, and thermal recommendations. This page synthesizes distributor pricing, drop-in compatible QorIQ alternatives, and practical design considerations not found in the standalone datasheet, including cross-reference guidance for engineering teams evaluating platform migrations.

見積もり お問い合わせ
P5040NSN72QC - QorIQ P5 64-Bit SoC, 4x 2.2GHz | NXP
P5040NSN72QC

P5040NSN72QC - QorIQ P5 64-Bit SoC, 4x 2.2GHz | NXP

The NXP QorIQ P5040NSN72QC is a quad-core 64-bit Power Architecture system-on-chip (SoC) from the QorIQ P5 family, integrating four e5500 cores running at up to 2.2 GHz, packaged in a 1295-ball FCBGA (FC-PBGA, 37.5 mm x 37.5 mm) and rated for an extended 0 to +105 C operating temperature range. According to the NXP product brief, the part delivers scalable 64-bit processing with single-, dual-, and quad-core devices, with a tightly coupled cache hierarchy engineered for low latency and integrated hardware acceleration blocks that offload networking and datapath workloads from the cores. A system-on-chip (SoC) integrates the CPU cores, memory controller, high-speed I/O controllers, and platform glue logic into a single device, replacing what previously required a CPU plus chipset plus multiple peripheral controllers. The QorIQ P5 line specifically targets compute-intensive but power-conscious control-plane applications in networking, telecom, and industrial equipment where deterministic performance and a rich I/O mix matter more than raw single-thread throughput. In NXP's portfolio, P5040 (quad-core) and P5021 (dual-core) sit at the top of the P5 family tree, which itself sits under the broader QorIQ communications-processor platform. Key features include four 64-bit e5500 cores at up to 2.2 GHz, integrated DDR3 / DDR3L memory controller with ECC support, integrated PCIe Gen2 controllers, integrated multi-gigabit Ethernet supporting 1 GbE and 10 GbE, integrated SATA controllers, hardware accelerators for cryptography, pattern matching, and packet processing, and a high-bandwidth CoreNet coherency fabric interconnecting cores, caches, and I/O. The extended 0 to +105 C junction range allows deployment in thermally constrained networking enclosures where ambient temperatures rise under load, and the FCBGA-1295 package exposes all SerDes lanes and I/O signals for maximum board-level flexibility. Architecturally, the device uses out-of-order e5500 cores backed by a private L1 cache and a shared L2/L3 platform cache, with memory and I/O coherency maintained by the CoreNet fabric. Hardware offload engines reduce CPU interrupt load and lower per-packet latency, which is essential for line-rate forwarding, encryption, and QoS scheduling in carrier-grade networking gear. Compared with discrete CPU-plus-NPU designs, the integrated approach reduces board area, BOM cost, and power consumption while improving determinism. Typical applications include enterprise and service-provider routers, switches, and network appliances, line cards for modular switches, telecom base-station controllers, industrial control and automation equipment, secure gateways, and networked storage controllers. The combination of PCIe, SATA, and multi-speed Ethernet makes it a single-chip solution for many control-plane aggregation roles. Engineers should pay close attention to power-rail sequencing and SerDes reference-clock design - the NXP hardware-design checklist describes the supported bring-up sequence and reference-clock topology required to bring all high-speed interfaces online reliably. This page aggregates distributor pricing, lifecycle information, drop-in alternatives, and design notes that supplement the manufacturer datasheet.

見積もり お問い合わせ
P5040NXE1TMB - QorIQ P5040 4-Core 1.8GHz Power Arch SoC | NXP
P5040NXE1TMB

P5040NXE1TMB - QorIQ P5040 4-Core 1.8GHz Power Arch SoC | NXP

The NXP (formerly Freescale) P5040NXE1TMB is a QorIQ P5040 communications processor SoC integrating four Power Architecture e5500 cores at 1.8 GHz with a 64-bit datapath, DDR3/3L memory controller with ECC, and a high-speed SerDes fabric supporting PCIe, 1/10 Gigabit Ethernet, and SATA in a 1295-ball FCBGA measuring 37.5 mm x 37.5 mm. The part is rated for the extended industrial temperature range of -40 C to +105 C and is targeted at networking, telecom, and industrial embedded applications. A QorIQ SoC is a system-on-chip that combines one or more Power Architecture CPU cores with integrated networking and I/O peripherals. Within the broader taxonomy, the P5040 sits under communications processor -> embedded microprocessor -> microprocessor (MPU) -> integrated circuit -> semiconductor. By integrating the CPU complex, memory controller, packet-processing engines, and SerDes on a single die, the QorIQ family reduces bill-of-materials cost and PCB area compared with multi-chip designs built around a generic CPU plus external PHYs and bridges. Key features include quad-core e5500 cores running up to 1.8 GHz, a 64-bit DDR3/DDR3L controller with ECC supporting up to 2133 MT/s, integrated 10 GbE and 1 GbE MACs, multiple PCIe Gen2 controllers, SATA 2.0 interfaces, a security engine (SEC), and hardware packet acceleration. The cache hierarchy pairs each core with a private L2 and a shared L3 cache for low-latency memory access. The 1.0 V to 1.1 V core supply is supplemented by independent rails for the DDR I/O and SerDes, allowing flexible power sequencing. The architecture uses an interconnect fabric that fans the four cores out to the coherent memory subsystem and to the I/O controllers. This topology is what allows the device to deliver multi-Gb/s packet throughput while running control-plane software stacks such as Linux, VxWorks, or QNX. The on-chip SEC engine accelerates IPsec, SSL/TLS, and bulk crypto, offloading security workloads from the CPU cores. Typical applications include multi-service routers, LTE and small-cell base stations, network-attached storage controllers, industrial gateways, and aerospace/defense communications platforms. Engineers select the P5040 when deterministic multi-core performance, integrated 10 GbE, and long-lifecycle supply matter more than absolute single-thread performance. Key trade-off: the 1295-ball FCBGA requires multi-layer PCB with microvia stack-ups, careful power-rail decoupling, and matched-length SerDes routing. Reference designs from the QorIQ hardware documentation should be followed closely, since signal-integrity violations on the SerDes will degrade link margin or cause enumeration failures. This page consolidates distributor availability, parametric drop-in candidates within the QorIQ P5 family, and practical design notes not contained in the manufacturer datasheet, giving engineers a single decision-grade reference.

見積もり お問い合わせ
P5040NXE7TMC - QorIQ P5 4-Core 1.8GHz SoC, 1295-FCBGA | NXP
P5040NXE7TMC

P5040NXE7TMC - QorIQ P5 4-Core 1.8GHz SoC, 1295-FCBGA | NXP

The NXP (formerly Freescale) P5040NXE7TMC is a quad-core 64-bit Power Architecture system-on-chip (SoC) from the QorIQ P5 communications platform family, integrating four e5500 cores running up to 1.8 GHz in a 1295-ball FCBGA (FCPBGA) package measuring 37.5 x 37.5 mm. The device combines high-performance CPU subsystems with hardware-accelerated networking, security, and I/O, targeting wired and wireless networking, industrial control, and aerospace/defense equipment operating over the industrial -40C to +105C temperature range. A QorIQ P5 SoC is a communications-processor class of multicore microprocessor that integrates CPU cores, a coherent interconnect, memory controllers, packet-processing engines, security accelerators, and high-speed serial interfaces onto a single die. In the broader taxonomy, it sits as a microprocessor (MPU) -> communications processor -> application-specific SoC -> semiconductor IC. The P5 platform was engineered by Freescale (now NXP) to scale from single-core to quad-core configurations on a pin- and software-compatible footprint, simplifying platform migration across performance tiers. Key differentiating specifications include the four e5500 cores with dual-issue 7-stage pipelines, support for up to 32 GB of DDR3/DDR3L with ECC, two integrated 10 Gigabit Ethernet MACs plus eight 1 Gigabit Ethernet MACs, multiple PCI Express Gen2 controllers, SATA 2.0 interfaces, and a SEC crypto engine. The -TMC suffix indicates the industrial temperature grade (-40C to +105C) with a silicon revision R2.1, providing long-life-cycle availability for embedded and aerospace platforms. The architecture combines out-of-order execution support, a hierarchical cache topology with shared L3, and tightly coupled datapath accelerators. The 10 GbE and packet-processing engines offload networking tasks from the cores, allowing the device to deliver line-rate throughput on multiple Gigabit ports simultaneously while leaving CPU cycles available for control-plane and application processing. Typical applications include multi-service routers and switches, network-attached storage (NAS) controllers, wireless base station equipment, industrial control gateways, and defense/aerospace embedded computing platforms where long-life-cycle silicon and ruggedized temperature grades are mandatory. When designing with this device, plan for a high-density FCBGA layout (1295 balls at 1 mm pitch typical) requiring multi-layer PCB stack-up, controlled-impedance routing for SerDes lanes, and substantial thermal management for the 37.5 x 37.5 mm package. Designers should also budget for the DDR3 ECC memory design rules and reference NXP's QorIQ P5040 reference design for validated power, clock, and reset sequencing. This page synthesizes distributor pricing, drop-in alternatives within the QorIQ P5 family, and practical design considerations not consolidated on a single manufacturer or distributor page.

見積もり お問い合わせ
P87C58X2BBD - 32KB OTP 80C51 MCU, 33MHz, LQFP-44 | NXP
P87C58X2BBD

P87C58X2BBD - 32KB OTP 80C51 MCU, 33MHz, LQFP-44 | NXP

The NXP P87C58X2BBD is an 8-bit CMOS microcontroller from the 80C51 family, featuring 32KB of OTP (One-Time Programmable) ROM, 256 bytes of RAM, and a maximum clock speed of 33 MHz, housed in a 44-pin LQFP package (MS-018, SOT-187-2). Based on the high-performance static 80C51 architecture, it operates over a wide voltage range of 2.7 V to 5.5 V and supports both 6-clock and 12-clock cycle modes for legacy software compatibility. The 32 programmable I/O lines, three 16-bit counter/timers, and a 6-source interrupt structure make it a versatile embedded controller. An 80C51 microcontroller is a Harvard-architecture 8-bit MCU that originated at Intel in 1980 and became one of the most widely deployed embedded processor cores. Within the taxonomy, the P87C58X2BBD falls under: 80C51 -> 8-bit microcontroller -> microcontroller -> embedded processor -> semiconductor. These devices typically integrate CPU core, program memory (ROM/OTP/Flash), data RAM, timers, serial I/O, and parallel I/O into a single die, making them suitable for standalone control applications. Key features include a 6-clock/12-clock mode select for software compatibility with legacy 8051 code, idle and power-down modes for low-power battery applications, an enhanced boolean processor, and an OTP ROM with 1000 erase/program cycles. The 256-byte on-chip RAM is ample for stack and variable storage in typical control loops. The LQFP-44 (10x10 mm) package with 32 I/O lines provides ample GPIO for peripheral interfacing. The P87C58X2BBD uses Philips (now NXP) high-density CMOS technology to deliver low-power, high-speed operation at 30/33 MHz. The static design allows the clock to be stopped and resumed without losing internal state, enabling advanced power-saving strategies in battery-powered and industrial applications. Typical applications include industrial control systems, consumer appliances, automotive body electronics (non-safety), smart sensors, motor control interfaces, and legacy 8051 firmware upgrades. The OTP variant is ideal for production runs where firmware is finalized and cost-per-unit matters more than field reprogrammability. When designing with this device, plan for OTP programming time during manufacturing; once programmed, the part cannot be re-flashed. Ensure your software stack is benchmarked against 6-clock versus 12-clock timing to preserve timing budgets. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet, providing engineering decision support beyond a raw spec sheet.

見積もり お問い合わせ
P87C591VFA - 8-Bit 80C51 MCU w/ CAN, 16KB OTP, 44-PLCC | NXP
P87C591VFA

P87C591VFA - 8-Bit 80C51 MCU w/ CAN, 16KB OTP, 44-PLCC | NXP

The NXP Semiconductors P87C591VFA is a single-chip 8-bit high-performance microcontroller with an on-chip CAN controller, derived from the 80C51 microcontroller family and including the PeliCAN functionality of the SJA1000 standalone CAN controller. It operates at up to 12 MHz, integrates 16 KB of on-chip OTP program memory, 512 bytes of AUX RAM, and 256 bytes of main RAM, and is housed in a 44-pin PLCC package qualified to AEC-Q100 for automotive applications. An 8-bit microcontroller (MCU) is a programmable logic device that fetches and executes an instruction set from on-chip ROM or OTP, manipulates data in registers, and interfaces with peripherals through digital I/O. The P87C591VFA belongs to the 80C51 architecture family (8051 core) and adds a hardware CAN 2.0B controller, making it a member of the broader category: microcontroller -> embedded controller -> semiconductor IC. It is intended for systems that need deterministic serial communication on a Controller Area Network bus without an external CAN ASIC. Key features include: 16 KB OTP program memory, 256 + 512 bytes RAM, four 8-bit I/O ports, three 16-bit timer/counters, a hardware watchdog timer, eight sources of interrupt with four priority levels, a 10-bit successive-approximation ADC with up to 6 analog inputs, and a full CAN 2.0B controller supporting both standard (11-bit) and extended (29-bit) identifiers. The 80C51 instruction set is binary-compatible with the industry-standard MCS-51, easing code reuse. Internally, the P87C591VFA pairs an 80C51 core with the PeliCAN block from the SJA1000, an 8-channel analog MUX feeding a 10-bit SAR ADC, and dual DPTR registers for fast memory block moves. The device supports 6 clock periods per machine cycle, with power-saving Idle and Power-Down modes that drop core current to a fraction of full-activity levels, important for always-on automotive nodes. Typical applications include automotive body controllers, CAN-based sensor nodes, industrial CANopen/DeviceNet slaves, HVAC controllers, lighting controllers, and battery management peripherals where deterministic CAN communication and AEC-Q100 temperature grading are required. Designers should note that the OTP memory variant requires a windowed EPROM or pre-programmed parts for prototyping; a flash-based derivative is the P87C591's companion part for development. Adequate decoupling (100 nF plus bulk) and a stable 5 V supply are required for reliable ADC and CAN bus operation.

見積もり お問い合わせ
PC9RS08KA2DWE - 8-Bit RS08 MCU, 2KB Flash, 10MHz | NXP
PC9RS08KA2DWE

PC9RS08KA2DWE - 8-Bit RS08 MCU, 2KB Flash, 10MHz | NXP

The NXP PC9RS08KA2DWE is an 8-bit RS08 microcontroller built around a streamlined S08 instruction set, offering 2KB of FLASH program memory, 63 bytes of RAM, and a 10MHz CPU core, all housed in an 8-pin SOIC (5.30mm / 0.209") package. The device operates from a single 1.8V to 5.5V supply and integrates 4 general-purpose I/O pins, an internal oscillator, and essential system-protection peripherals including Low Voltage Detect (LVD), Power-On Reset (POR), and a Watchdog Timer (WDT). An RS08 microcontroller is a derivative of Freescale/NXP's HCS08 architecture, designed as a cost- and code-density-optimized 8-bit core for high-volume, ultra-low-cost embedded applications. RS08 devices retain the C-friendly S08 instruction set while reducing core area, making them the smallest and lowest-power members of the Freescale 8-bit portfolio. RS08 microcontrollers belong to the broader category of microcontrollers (MCU), which sit within embedded controllers and are essential building blocks of modern electronic systems. Key features include a single voltage supply range of 1.8V to 5.5V, 4 I/O pins for compact sensor and switch interfaces, an internal oscillator that eliminates the need for an external crystal, and robust system protection through integrated LVD, POR, and WDT peripherals. The simplified S08 instruction set, augmented with the high-performance LDA, STA, and CLR instructions, delivers a balance of code density and execution speed for cost-sensitive designs. The RS08 core uses a Von Neumann architecture with a simplified instruction pipeline and a reduced register file versus the full S08 family, targeting ultra-low-power and pin-constrained applications. The 10MHz bus speed at 5V provides ample throughput for sensor sampling, switch debouncing, and simple state-machine control, while the FLASH memory supports in-application reprogramming for field updates. Typical applications include battery-powered household appliances, remote-control transmitters, LED lighting controllers, low-end toys and personal-care devices, simple sensor interfaces, and replacement of discrete logic in white goods. The wide 1.8V to 5.5V supply range and low pin count (8-SOIC) make it ideal for compact, single-cell or 3V/5V mains-derived designs. When designing with this device, ensure the operating voltage stays within the 1.8V to 5.5V range and that adequate decoupling (typically 100nF plus bulk capacitance) is placed near the supply pin. The 4 available I/O pins limit the design to minimalist interfaces such as a single switch input, an LED output, and a one-wire or UART communication channel. This page synthesizes distributor pricing, drop-in and footprint-compatible alternatives, and practical design notes not found in the manufacturer datasheet, helping engineers select and source the PC9RS08KA2DWE for new designs and legacy maintenance.

見積もり お問い合わせ
PC9RS08KA2PAE - 8-Bit RS08 MCU, 2KB Flash, 10MHz | NXP
PC9RS08KA2PAE

PC9RS08KA2PAE - 8-Bit RS08 MCU, 2KB Flash, 10MHz | NXP

The NXP PC9RS08KA2PAE is an 8-bit RS08 microcontroller featuring a simplified S08 instruction set with high-performance LDA, STA, and CLR extensions, 2KB (2K x 8) of on-chip FLASH program memory, 63 bytes of RAM, and an internal oscillator supporting up to 10MHz CPU operation. Housed in an 8-pin PDIP package (0.300 inch, 7.62mm body width), it provides four general-purpose I/O pins plus integrated peripherals including a low-voltage detector (LVD), power-on reset (POR), and a watchdog timer (WDT) for embedded safety. An RS08 microcontroller is a reduced-pin-count, low-cost derivative of the Freescale/NXP S08 family, optimized for cost-sensitive, space-constrained applications that need deterministic 8-bit performance without external components. Architecturally, an RS08 sits within the broader 8-bit MCU taxonomy: microcontroller -> embedded controller -> 8-bit MCU -> HCS08/RS08 family -> cost-optimized sub-family. The CPU core implements a streamlined S08 instruction set so legacy ColdFire/S08 code can be ported with minimal effort while the silicon footprint and BOM cost remain minimal. Key feature highlights include 2KB FLASH (in-system programmable), 63 bytes of RAM supporting a tiny memory model with single-byte direct addressing for the first 16 locations, an internal oscillator that eliminates the need for an external crystal in most designs, four GPIO pins multiplexed with peripheral functions, and shadow register support for fast context switching in interrupt service routines. The simplified instruction set retains ADD, SUB, INC, and DEC for tiny addressing mode, allowing C compilers and assembler code to generate compact binaries. Typical applications include low-cost consumer appliances, IR remote controls, single-chip sensor interfaces, LED lighting controllers, simple battery chargers, and any embedded product that needs an 8-bit brain with on-chip non-volatile memory and a small pin count. The integrated LVD and watchdog make it suitable for unattended or mains-powered equipment that must reset cleanly on brown-out events. When designing with the PC9RS08KA2PAE, ensure the supply rail stays within the device's Vcc/Vdd range and place a 0.1 uF decoupling capacitor as close as possible to pin 8 (Vdd). CodeWarrior for RS08 (now offered as NXP's free CodeWarrior for ColdFire+RS08) and P&E Multilink/Cyclone programmers are required for in-circuit development. As the part is marked Obsolete in distributor listings, designers of new products should plan for last-time-buy or consider NXP S08KA2 series successors.

見積もり お問い合わせ
PC9S08QE128CLH - 8-bit S08 MCU 128KB Flash 50MHz 64-LQFP | NXP
PC9S08QE128CLH

PC9S08QE128CLH - 8-bit S08 MCU 128KB Flash 50MHz 64-LQFP | NXP

The NXP PC9S08QE128CLH is an 8-bit S08 microcontroller IC delivering 50MHz CPU performance with 128KB (128K x 8) of embedded FLASH program memory, housed in a 64-pin LQFP (10x10 mm) package. This industrial-grade member of the S08 family integrates enhanced peripherals and is targeted at cost-sensitive embedded control designs requiring on-chip LCD driver support and multiple serial interfaces. An 8-bit microcontroller (MCU) is a microprocessor integrated with memory, peripherals, and I/O on a single die. Within the broader semiconductor taxonomy, an MCU belongs to the embedded processor category, which itself sits under the integrated circuit hierarchy. The 8-bit designation refers to the data bus width and ALU datapath; S08 is NXP's (formerly Freescale) 8-bit HCS08 family using a modified Harvard architecture and a CPU08 instruction set. Compared with 16-bit MCUs (e.g., S12) and 32-bit MCUs (e.g., ColdFire V1/Kinetis E), 8-bit S08 devices prioritise low cost, low power, and deterministic interrupt response for appliance, white-goods, and industrial-control use cases. Key features of the PC9S08QE128CLH include 128KB FLASH for firmware storage, on-chip RAM for working data, an integrated LCD driver (a defining feature of the QE sub-family), and a peripheral set that typically includes timers (TPM), ADC, I2C, SCI (UART), and SPI. The 50MHz bus clock supports fast instruction throughput for time-critical control loops. The 64-LQFP (10x10) package provides 64 gull-wing leads on a 0.5mm pitch, suitable for standard SMT reflow and easy hand-solder prototyping. ECCN EAR99 classification indicates export-friendly commercial control. Architecturally, the S08 core uses a 16-bit stack pointer with banked RAM access and an HCS08 instruction set that is source-compatible with the legacy HC08 family while adding additional addressing modes and a background debug mode (BDM) for non-intrusive in-circuit debugging. The QE128 sub-family is the largest memory-density and most peripheral-rich 8-bit S08 device, offering more I/O than the QE64 and QE96 variants. Typical applications include white goods and appliance control, HVAC thermostats and sensor front-ends, industrial metering and instrumentation, low-cost consumer devices with LCD user interfaces, and embedded control subsystems. The integrated LCD driver eliminates the need for an external LCD bias-generator chip, reducing BOM cost and PCB area in display-equipped designs. Designers should plan oscillator and decoupling layout early, route the LCD segment pins away from switching signals to minimise display contrast artefacts, and follow the Freescale/NXP BDM pinout for in-circuit debug connection. Choosing the 64-LQFP variant over smaller QFP packages aids thermal dissipation and simplifies prototype rework. This page synthesises distributor pricing, drop-in alternatives, and design notes that go beyond the manufacturer datasheet, including AEC-Q grade comparisons and package trade-offs for migration within the S08QE128 family.

見積もり お問い合わせ
PCF51JM128EVLK - 32-Bit ColdFire V1 MCU, 128KB Flash | NXP
PCF51JM128EVLK

PCF51JM128EVLK - 32-Bit ColdFire V1 MCU, 128KB Flash | NXP

The NXP PCF51JM128EVLK is a 32-bit ColdFire V1 microcontroller from the MCF51JM Series, delivering 50 MHz core performance with 128 KB of embedded Flash and 16 KB of SRAM, housed in an 80-pin LQFP (14x14 mm) package. It integrates USB OTG, CAN, I2C, SCI, and SPI connectivity in a single device, targeting cost-sensitive industrial and embedded USB applications. Background Knowledge: A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (Flash/ROM), working memory (RAM), and peripheral interfaces (UART, timers, ADC, GPIO, USB, CAN, etc.). ColdFire V1 is NXP's 32-bit RISC architecture derived from the original Motorola 68000 instruction set, optimized for embedded systems that need higher performance than 8/16-bit MCUs without the overhead of ARM Cortex-M cores. MCF51JM Series specifically adds USB On-The-Go capability, making it a popular choice for USB peripherals and industrial controllers. Key differentiating features include the integrated USB 2.0 Full-Speed OTG controller (with on-chip transceiver and pull-up/pull-down resistors), 66 general-purpose I/O pins, and a rich peripheral set: 2x SCI (UART), 2x SPI, 2x I2C, 6-channel PWM, a 12-bit ADC, and a 16-bit timer. The 80-LQFP package provides generous pin count for multi-interface designs while remaining hand-solderable for prototyping. Technical depth: The ColdFire V1 core uses a 16/32-bit variable-length instruction encoding that balances code density with 32-bit throughput. The integrated USB OTG controller supports both device and host roles with internal 3.3V regulator and DP/DM pull resistors, eliminating external PHY components. The Flash controller supports in-application programming (IAP) and byte-level EEPROM emulation, allowing non-volatile data storage alongside the main 128 KB program image. Typical applications include USB-to-UART bridges, USB human-interface devices (HID), industrial control nodes with CAN connectivity, low-cost sensor hubs, and embedded controllers in appliances. The combination of USB, CAN, and multi-protocol serial interfaces makes it ideal for industrial gateways that aggregate sensor data over CAN and expose it to a host PC via USB. Design consideration: The USB D+/D- traces must be routed as a 90-ohm differential pair with length matching; bypassing the on-chip 3.3V regulator to power the MCU core requires a 4.7 uF decoupling capacitor on the VREG pin. The device operates from -40C to +85C industrial temperature range. This page synthesizes distributor availability, drop-in same-package alternatives, and design notes not found in the manufacturer datasheet to support sourcing and design decisions.

見積もり お問い合わせ
PCF51JM128VLH - 32-bit ColdFire MCU, 128KB Flash, USB OTG | NXP
PCF51JM128VLH

PCF51JM128VLH - 32-bit ColdFire MCU, 128KB Flash, USB OTG | NXP

The NXP PCF51JM128VLH is a 32-bit ColdFire V1 MCF51JM microcontroller delivering 50 MHz CPU performance with 128 KB of Flash program memory and 16 KB of RAM, housed in a 64-pin LQFP (10x10 mm) package. It integrates USB OTG (On-The-Go) connectivity alongside CANbus, I2C, SCI, and SPI peripheral interfaces, and exposes 51 general-purpose I/O pins for mixed-signal embedded designs. What is a ColdFire microcontroller? ColdFire is a 32-bit reduced instruction set computing (RISC) architecture originally derived from the Motorola 68000 family and maintained today by NXP. Within the broader taxonomy, a ColdFire MCU belongs to the hierarchy: microcontroller -> embedded processor -> semiconductor. ColdFire V1 targets cost-sensitive, deterministic real-time applications, balancing 32-bit performance with low power consumption. It is widely deployed in industrial control, USB peripherals, automotive body electronics, and consumer devices where deterministic interrupt latency and a mature toolchain matter more than raw MHz. Key features of the PCF51JM128VLH include 128 KB of embedded Flash for program storage, 16 KB of SRAM for data and stack, a 50 MHz ColdFire V1 core, and integrated USB OTG with on-chip transceiver - eliminating the need for an external PHY. The device also includes a low-voltage detection (LVD) module, programmable watchdog timer, multiple PWM channels, and 51 GPIO pins. The 64-LQFP (10x10 mm) package provides ample pin count for mixed-signal designs while remaining compatible with hand-solderable and reflow processes. The integrated USB OTG controller is the defining architectural feature. Unlike MCUs that require an external USB peripheral controller, the PCF51JM128VLH implements the USB 2.0 full-speed transceiver, serialization, and protocol engine on-die. This simplifies USB device, host, and On-The-Go designs while reducing BOM cost. The ColdFire V1 core paired with hardware USB enables deterministic USB latency, which is valuable for industrial USB instrumentation, human-interface devices (HID), and point-of-sale terminals. Typical applications include USB HID peripherals such as custom keyboards and barcode scanners, industrial CAN nodes communicating over CANbus with USB diagnostics, USB-to-serial bridge converters, low-speed consumer devices with USB charging or data interfaces, and human-machine interface (HMI) panels with mixed digital I/O. The 128 KB Flash budget is sufficient for USB stacks (e.g., Freescale/NXP bare-metal or MQX-compatible USB frameworks) plus application code. When designing with this part, allocate sufficient decoupling on VDD (typically 100 nF + 10 uF bulk near the pins) and follow NXP's reference layout for the USB DP/DM differential pair. Because the device is in the obsolete lifecycle stage per the verified distributor data, validate long-term availability with your supply chain team before committing to new production runs. This page synthesizes distributor pricing, lifecycle status, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone.

見積もり お問い合わせ
PCF51QU64VLF - Coldfire V1 MCU 32-Bit 50MHz 64KB Flash 48-LQFP | NXP Semiconductors
PCF51QU64VLF

PCF51QU64VLF - Coldfire V1 MCU 32-Bit 50MHz 64KB Flash 48-LQFP | NXP Semiconductors

The NXP Semiconductors PCF51QU64VLF is a 32-bit Coldfire V1 microcontroller from the MCF51Qx family, integrating 64KB of program flash and running at up to 50MHz core clock, housed in a 48-pin LQFP (7x7 mm) package. A microcontroller (MCU) is a single-chip computer that combines a CPU core, program and working memory, peripherals, and I/O on one die. The Coldfire V1 core is an NXP-specific implementation of a variable-length RISC architecture derived from the original Coldfire line, optimized for deterministic embedded control with low power consumption. MCUs sit hierarchically beneath microprocessors and systems-on-chip, and they dominate the embedded controller category in industrial, appliance, and consumer products. Key specifications include 64KB (64K x 8) embedded flash memory, 35 general-purpose I/O lines, and a peripheral set featuring DMA, LVD (low-voltage detect), POR (power-on reset), PWM channels, and an EBI/EMI external bus interface. Connectivity options include one I2C bus, one SPI bus, and one UART/USART channel. The device is characterized for a supply voltage range from 1.8V to 3.6V (with flash write voltage range specified separately), and operates across an extended industrial temperature range. The Coldfire V1 core implements a single-cycle multiply-accumulate and a tightly-coupled peripheral bridge, enabling deterministic interrupt latency suitable for motor control and power conversion loops. The 50MHz maximum CPU frequency yields approximately 50 MIPS of throughput, and the unified address space simplifies C-language firmware development with standard toolchains such as CodeWarrior. Typical applications include industrial control modules, low-end consumer appliances, smart sensor nodes, and small-format human-machine interface boards. The combination of 64KB flash and an external bus makes the PCF51QU64VLF especially well suited to designs that must execute a real-time control loop while still communicating with external memory-mapped peripherals. A critical design consideration is decoupling: place a 100nF ceramic bypass on each VDD/VSS pair within two millimeters of the package, and reserve a 4.7uF bulk capacitor near the regulator output. The external bus pins (EBI/EMI) require series termination when driving long PCB traces to avoid ringing. This page synthesizes distributor stock, drop-in alternatives from the same Freescale/NXP MCF51Q family, and practical design notes not found on a single manufacturer product page.

見積もり お問い合わせ
PIC10F200-E/MC - 8-Bit Flash MCU, 384B, 4MHz, 8-DFN | Microchip
PIC10F200-E/MC

PIC10F200-E/MC - 8-Bit Flash MCU, 384B, 4MHz, 8-DFN | Microchip

The Microchip Technology PIC10F200-E/MC is an 8-bit, fully-static, Flash-based CMOS microcontroller in a 6/8-pin DFN (2x3 mm) package with 384 bytes of program Flash, 16 bytes of RAM, and 4 MHz internal oscillator execution. It integrates a RISC core delivering 33 single-word/single-cycle instructions with 12-bit-wide instruction words, achieving typical 2:1 code compression over competing 8-bit MCUs and 1 MIPS performance from a 4 MHz clock. An 8-bit microcontroller (MCU) is a small computer-on-a-chip that integrates a CPU, program memory, data memory, and I/O peripherals on a single die; in the broader component taxonomy it sits below microprocessors and above simple logic. The PIC10F200 belongs to the baseline PIC10F family from Microchip Technology - the smallest Flash-programmable 8-bit MCU line in the industry. Unlike 32-bit Cortex-M parts, 8-bit MCUs are optimized for deterministic, low-power, low-cost glue logic replacement in cost-sensitive embedded designs. Key features include 4 I/O pins (GPIO), an 8-bit timer (TMR0) with 8-bit prescaler, an integrated 4 MHz internal precision oscillator, a power-on reset (POR) and device reset timer (DRT), and a watchdog timer (WDT) with its own on-chip RC oscillator for reliable operation without external components. The wide operating voltage range of 2.0V to 5.5V and -40C to +125C extended temperature grade support battery-powered and industrial-grade designs. The PIC10F200-E/MC uses a Harvard RISC architecture with separate program and data buses, executed in a single instruction cycle (4 clocks) except for program branches which take two cycles. The Flash memory supports in-circuit serial programming (ICSP) via two pins (GP0/GP1), enabling firmware updates in the field without removing the device. An 8-bit wide instruction word, 12-bit program memory width, and 8-level hardware stack simplify C and assembly development with the MPLAB XC8 toolchain. Typical applications include low-end logic replacement in consumer appliances, PWM LED dimming, fan/thermostat control in HVAC, battery chargers, and sensor signal conditioning. The 8-DFN (MC) package enables surface-mount designs under 6 mm squared - ideal where PCB area is at a premium. The wide VDD range and small footprint make this part popular as a configurable replacement for discrete 555 timer and CMOS logic circuits in production designs. When designing with this MCU, note that only 4 of the 6 functional pins are brought out as GPIO on the 8-DFN package (the SOT-23 6-pin version exposes all 6). Place a 100 nF decoupling capacitor as close to VDD as possible, and consider the in-circuit serial programming (ICSP) pinout when laying out the PCB. The internal 4 MHz oscillator has a factory calibration of +/- 1% typical, eliminating external crystals in most cost-sensitive designs. This page synthesizes distributor pricing, verified drop-in alternatives within the PIC10F family, and practical PCB layout/design notes that complement the manufacturer datasheet and standard distributor listings.

見積もり お問い合わせ
PIC10F200-E/P - 8-bit Flash MCU, 384B, 4MHz | Microchip
PIC10F200-E/P

PIC10F200-E/P - 8-bit Flash MCU, 384B, 4MHz | Microchip

The Microchip Technology PIC10F200-E/P is a low-cost, high-performance, 8-bit, fully static, Flash-based CMOS microcontroller. Housed in an 8-pin PDIP (P) through-hole package, it features 384 bytes of Flash program memory (256 x 12 words), 16 bytes of data RAM, and 4 I/O pins, and operates at up to 4 MHz instruction clock. The device is rated for the -40C to +125C extended industrial temperature range (the "E" suffix denotes the extended temperature grade), making it suitable for harsh-environment designs. What is a PIC10F microcontroller? The PIC10F family is Microchip's smallest 8-bit PIC microcontroller line, positioned at the bottom of the 8-bit MCU hierarchy: 8-bit MCU -> microcontroller -> embedded controller -> semiconductor. These parts use a RISC architecture with only 33 single-word, single-cycle instructions, which makes them ideal for cost-sensitive, space-constrained applications where a few pins of digital logic are needed in place of discrete glue logic or small ASICs. The PIC10F200 is the most basic member of the family, deliberately stripped down to the smallest possible memory and pin count to minimize cost. Key features include an internal 4 MHz oscillator (no external crystal required), a 4-channel 8-bit Analog-to-Digital Converter (ADC) on most family members, an 8-bit timer/counter with prescaler, and a watchdog timer with its own on-chip RC oscillator for reliable operation. The Flash program memory supports in-circuit serial programming (ICSP) and in-circuit debugging, enabling rapid prototyping and field firmware updates without removing the part from the board. The PIC10F200 is fabricated in CMOS technology with a wide 2.0V to 5.5V operating voltage range, allowing direct battery operation. Its ultra-low power consumption makes it well-suited for battery-powered and energy-harvesting designs. The device consumes only a few hundred microamps active and supports a sleep mode with nanoamp-level standby current for power-critical applications. Typical applications include LED lighting control, simple sensor signal conditioning, battery chargers, low-end consumer appliances, and replacement of discrete logic in space-constrained boards. The 8-pin PDIP (P) package is favored for prototype and hobbyist work because it accepts standard through-hole tooling and breadboards. When designing with this device, ensure that all unused I/O pins are configured as outputs and tied low (or high, depending on application), because floating inputs can draw excessive supply current and inject noise into adjacent analog pins. The MCLR pin (pin 4) is shared with the programming voltage input and should be pulled up to VDD through a 10 kohm resistor for normal operation. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone.

見積もり お問い合わせ
PIC10F200-I/MC - 8-bit Flash MCU, 384B Flash, 4MHz, 8-DFN | Microchip
PIC10F200-I/MC

PIC10F200-I/MC - 8-bit Flash MCU, 384B Flash, 4MHz, 8-DFN | Microchip

The Microchip PIC10F200-I/MC is a low-cost, high-performance, 8-bit, fully static, Flash-based CMOS microcontroller housed in an 8-pin DFN (2x3 mm) package. It features 384 bytes of Flash program memory (256 x 12 words), 16 bytes of RAM, and 4 MHz internal oscillator across a 2.0V to 5.5V operating range. The device uses a RISC architecture with 33 single-word/single-cycle instructions, giving an order-of-magnitude performance advantage over competing 8-bit microcontrollers in its class. An 8-bit microcontroller (MCU) is a small, self-contained computer-on-a-chip that integrates a CPU, RAM, non-volatile program memory, and I/O peripherals into a single IC. Within the broader taxonomy, the PIC10F200 sits in the lowest-pincount tier of 8-bit microcontrollers, classified as an ultra-small Flash MCU; it is a sub-class of microcontrollers, which in turn belong to microprocessors, which belong to integrated circuits and finally to semiconductors. The PIC10F200 family is designed for applications that need real microcontroller functionality at the cost of a discrete logic IC, replacing 555 timers, op-amp sequencers, and small logic packages with programmable intelligence. Key features of the PIC10F200-I/MC include an internal 4 MHz oscillator, 4-bit digital I/O, one 8-bit timer, a Watchdog Timer with on-chip RC oscillator, in-circuit serial programming (ICSP), and Power-on Reset. The device operates from -40C to +85C industrial temperature range, draws microampere-level supply current, and supports CMOS/TTL-compatible I/O. The 8-DFN (Dual Flat No-lead) package measures only 2 mm x 3 mm, making it one of the smallest microcontrollers in volume production. Typical applications include logic-chip replacement (small glue-logic functions), battery chargers, LED flashers, timer substitutes for 555 circuits, sensor-conditioning front-ends, and ultra-low-cost consumer products such as toys and personal-care devices. Four I/O pins provide enough flexibility for most simple sequencing or PWM-style tasks. When designing with this MCU, note that code execution is single-cycle at 4 MHz, giving 1 us instruction time (branches take 2 cycles). Programming is performed through ICSP using two pins (GP0/GP1), which must be accessible on the PCB. Designers upgrading to PIC10F202/204/206 should verify pinout compatibility carefully, as the larger siblings add features but share the same DFN footprint. This page synthesizes distributor pricing, drop-in same-package alternatives, and practical design notes drawn from the manufacturer datasheet and authorized distributor listings.

見積もり お問い合わせ
PIC10F200-I/P - 8-bit 4MHz 384B Flash MCU 8-PDIP | Microchip
PIC10F200-I/P

PIC10F200-I/P - 8-bit 4MHz 384B Flash MCU 8-PDIP | Microchip

The Microchip Technology PIC10F200-I/P is a 6-pin (8-PDIP pinout) 8-bit Flash-based CMOS microcontroller delivering 384 bytes of program memory, 16 bytes of RAM, and 4 I/O pins in an 8-pin PDIP through-hole package. The device executes instructions at 4 MHz from its internal 4 MHz RC oscillator and consumes only a few hundred microamperes in active mode for ultra-low-power embedded applications. The "-I" suffix designates an industrial temperature grade of -40C to +85C, while the "/P" suffix denotes the PDIP-8 package. A microcontroller (MCU) is a single-chip computer containing a CPU core, program memory (Flash/ROM), data memory (RAM), and programmable I/O peripherals. The PIC10F200 belongs to Microchip's 8-bit PIC10F family - the smallest, lowest-cost microcontrollers in the PIC architecture - designed for logic replacement, simple sequencing, and glue logic applications. It employs a RISC architecture with 33 single-word/single-cycle instructions, giving it code density and deterministic execution that outperforms many 8051-class competitors. Within the broader component taxonomy, the PIC10F200 is a microcontroller -> 8-bit MCU -> embedded controller -> semiconductor IC. Key features include 384 bytes of Flash program memory (256 x 12-bit words), 16 bytes of SRAM data memory, an 8-bit timer/counter, an internal 4 MHz oscillator (no external crystal required), wide operating voltage from 2.0V to 5.5V, in-circuit serial programming (ICSP), and a power-on reset with brown-out detection. The 8-PDIP package allows breadboard-friendly through-hole prototyping, which is unusual in this price-and-size class dominated by SOT-23-style surface-mount parts. The architecture combines a Harvard-style program/data memory split with a 12-bit instruction word, delivering typical 2:1 code compression versus 8-bit CISC alternatives. The internal 4 MHz RC oscillator eliminates external clock components while supporting calibration via the OSCCAL register. The single 8-bit timer (TMR0) with optional watchdog timer supports periodic wakeup and event-timing applications. The device supports in-circuit debugging through ICSP and an ICD interface. Typical applications include logic-replacement in appliances and consumer products, LED sequencing and blinking controllers, simple sensor signal conditioning, battery-powered devices, hardware sequencers, fan controllers, and toy electronics. Its 2.0V-5.5V operating range and sub-mA active current make it suitable for coin-cell and 2xAA battery designs. When designing with this part, mind the limitation of only 4 usable I/O pins (GP0-GP3), since pins 5-8 are shared with VDD, VSS, and ICSP functions. Always reserve one I/O for ICSP programming. The internal oscillator accuracy is typically ±1% after calibration, which may be insufficient for UART timing without software compensation. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet, providing an engineer-focused reference for selecting the PIC10F200-I/P across cost-sensitive embedded designs.

見積もり お問い合わせ
PIC10F200T-E/OT - 8-bit MCU, 384B Flash, SOT-23-6 | Microchip
PIC10F200T-E/OT

PIC10F200T-E/OT - 8-bit MCU, 384B Flash, SOT-23-6 | Microchip

The Microchip Technology PIC10F200T-E/OT is an 8-bit PIC microcontroller in a 6-pin SOT-23-6 surface-mount package with 384 bytes of Flash program memory, 16 bytes of RAM, and 4 I/O pins operating at 4 MHz from a 2.0V to 5.5V supply. The device is rated for the extended industrial temperature range of -40C to +125C and ships on a 3000-piece tape-and-reel carrier with a suffix code /OT denoting the SOT-23-6 package option. A microcontroller (MCU) is a single-chip computer containing a CPU core, program memory, working RAM, and programmable I/O peripherals. The PIC10F200 sits at the bottom of the 8-bit PIC family hierarchy - microcontroller -> 8-bit MCU -> PIC10 family -> low-cost Flash MCU - and is engineered for applications where BOM cost, PCB area, and predictable performance outweigh raw throughput. Its RISC architecture executes 33 single-cycle (1 us at 4 MHz) instructions from a 12-bit-wide instruction word, delivering roughly 2:1 code density over competing 8-bit cores. Key features include an internal 4 MHz oscillator with no external components required, three usable I/O pins plus one input-only pin (GP3), an 8-bit timer/counter (TMR0) with watchdog, in-circuit serial programming (ICSP), code protection, and an ultra-low 100 nA sleep current for battery-powered duty-cycled designs. The SOT-23-6 footprint is one of the smallest MCU packages available, enabling direct replacement of discrete 555-timer or logic-gate circuits in space-constrained products. The architecture is built around a Harvard-style CPU with separate program and data buses, eight-level hardware stack, and a single-cycle instruction fetch pipeline. This deterministic execution model simplifies real-time firmware, while the wide 12-bit instructions pack more work into each Flash word - reducing total Flash consumption and enabling the 384-byte program budget to host meaningful control loops. Typical applications include LED blink and chase controllers, battery status indicators, appliance timer replacements for 555 circuits, charger indicator logic, toy sound sequencers, and small-sensor interfaces. The wide 2.0V to 5.5V supply range allows direct connection to single-cell Li-ion, two-cell alkaline, or 5V regulated rails without level translation. Designers should note that only three pins (GP0, GP1, GP2) are bidirectional; GP3 is input-only and pin 1 is reserved for ICSP. A 100 nF decoupling capacitor as close as possible to VDD is mandatory, and unused I/O must be configured as outputs low to minimize sleep current. This page consolidates verified distributor pricing, drop-in compatible SOT-23-6 alternatives, and design notes that go beyond the manufacturer datasheet to help engineers evaluate the PIC10F200T-E/OT quickly.

見積もり お問い合わせ
PIC10F202-E/P - 8-Bit 4MHz 768B Flash MCU | Microchip
PIC10F202-E/P

PIC10F202-E/P - 8-Bit 4MHz 768B Flash MCU | Microchip

The Microchip Technology PIC10F202-E/P is a low-cost, high-performance, 8-bit, fully-static, Flash-based CMOS microcontroller housed in an 8-pin PDIP through-hole package. It features 768 bytes of Flash program memory (512 x 12 words), 24 RAM bytes, 4 MHz internal oscillator, and 4 I/O pins. According to Microchip product page data, the device operates across a 2.0V to 5.5V supply range and delivers 33 single-word/single-cycle RISC instructions for compact, deterministic code execution. A Flash microcontroller is a self-contained computing IC that combines a CPU core, non-volatile program memory (Flash), volatile working memory (RAM), and peripherals on a single die. The PIC10F202 belongs to the 8-bit microcontroller family in the broader category of microcontrollers (MCU) within integrated circuits, sitting under the RISC architecture umbrella and optimized for cost-sensitive embedded control. Compared to competing 8-bit CISC architectures in the same price bracket, the PIC10F202 delivers roughly an order-of-magnitude higher MIPS performance due to its 1-instruction-per-cycle pipeline, with most instructions executing in 1 us at 4 MHz. Key differentiating features include 6 I/O lines shared with 4 I/O functions (one input-only pin, one output-only pin, two bidirectional), one 8-bit timer (Timer0), a watchdog timer with on-chip RC oscillator, an internal 4 MHz calibrated oscillator, and in-circuit serial programming (ICSP) capability. The device draws a typical active current under 1 mA at 4 MHz and supports a power-saving Sleep mode with wake-up on pin change. It is rated for the -40C to +125C extended industrial temperature range as indicated by the -E suffix. Architecturally, the PIC10F202 uses a Harvard-style RISC core with a 12-bit wide instruction word, providing 2:1 typical code compression versus competing 8-bit MCUs in its class. Its 4 MHz internal oscillator eliminates external clock components, reducing BOM cost and PCB area. A precision bandgap reference and on-chip POR/Brown-out Reset (BOR) improve system reliability in noisy industrial environments. Typical applications include low-cost consumer appliances, battery-powered devices, LED lighting controllers, simple sensor interfaces, and automotive accessory modules. The wide operating voltage and industrial temperature range also make it suitable for harsh-environment sensor conditioning and IoT edge nodes. In -E/P form it is supplied in a through-hole PDIP-8 package suited for prototyping, breadboarding, and field-replaceable designs. When designing with this part, note that the 4 I/O pins are shared with GP0, GP1, GP2, GP3 and the output-only GP4/GP5 functions; GP3 is input-only. The device lacks an analog comparator or ADC, so applications requiring analog signal acquisition need an external ADC companion. Programming is performed via ICSP using the ICSPCLK/ICSPDAT pins shared with GP0/GP1. This page synthesizes distributor pricing, same-package drop-in alternatives, and practical design notes not found on a single manufacturer datasheet page.

見積もり お問い合わせ
PIC10F202-I/P - 8-bit Flash MCU, 768B, 4MHz, 8-PDIP | Microchip
PIC10F202-I/P

PIC10F202-I/P - 8-bit Flash MCU, 768B, 4MHz, 8-PDIP | Microchip

The Microchip Technology PIC10F202-I/P is a low-cost, high-performance, 8-bit, fully-static, Flash-based CMOS microcontroller in an 8-pin PDIP through-hole package. It features 768 bytes of Flash program memory (512 x 12 words), 24 bytes of RAM, 4 MHz internal oscillator, and 4 I/O pins, with an industrial operating temperature range of -40C to +85C. The device operates from 2.0V to 5.5V and carries AEC-Q100 automotive qualification per the datasheets.com parametric record. A microcontroller (MCU) is a single-chip computer that integrates a CPU, memory (Flash, RAM, EEPROM), and peripherals onto one die. The PIC10F202 belongs to the 8-bit MCU category, which sits below 32-bit microcontrollers in compute complexity but excels in cost, deterministic real-time response, and ultra-low pin-count packages. Within Microchip's portfolio, the PIC10F family represents the smallest-footprint 8-bit PIC microcontrollers, designed for glue logic replacement and space-constrained analog/digital control. The PIC10F202 uses a RISC architecture with 33 single-word, single-cycle instructions, providing an order-of-magnitude performance advantage over competitors in the same price category. Key features include an internal 4 MHz precision oscillator eliminating external crystal requirements, four bidirectional I/O pins with individual direction control, an 8-bit timer with prescaler, and an analog comparator module. The Flash-based program memory supports in-circuit serial programming (ICSP) for field updates. The WDT, Power-on Reset, and Brown-out Detection circuitry provide robust autonomous operation. With only 6 active pins and a 1 us instruction cycle, the PIC10F202 replaces discrete logic and small ASICs in cost-sensitive designs. Typical applications include automotive subsystems requiring AEC-Q100 qualification, consumer appliance controls, LED lighting drivers, sensor signal conditioning, and IoT edge nodes. The industrial temperature grade and wide operating voltage make it suitable for both battery-powered portable devices and 5V industrial rails. When designing with this device, allocate the GP0-GP3 pins carefully because only 4 I/O are available. Use ICSP for firmware provisioning and reserve the MCLR pin as a reset input with the proper pull-up topology. The internal 4 MHz oscillator has +/- 1% accuracy over voltage and temperature, adequate for UART bit-banging but tight for CAN or USB timing.

見積もり お問い合わせ
PIC10F202T-E/OT - 8-Bit 4MHz 768B Flash MCU | Microchip | SOT-23-6
PIC10F202T-E/OT

PIC10F202T-E/OT - 8-Bit 4MHz 768B Flash MCU | Microchip | SOT-23-6

The Microchip Technology PIC10F202T-E/OT is a low-cost, high-performance 8-bit fully-static Flash-based CMOS microcontroller housed in a 6-pin SOT-23-6 package, delivering 4 MHz CPU performance with 768 bytes (512 x 12 words) of program Flash and 24 bytes of RAM in one of the industry's smallest microcontroller footprints. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory, RAM, and peripherals. Within the semiconductor taxonomy, the PIC10F202T-E/OT belongs to the 8-bit microcontroller family -> RISC architecture microcontroller -> embedded controller -> semiconductor IC. It uses a 12-bit instruction word and executes 33 single-word/single-cycle instructions, with all instructions completing in 1 µs (except program branches, which take 2 µs). The device supports an operating voltage range of 2.0 V to 5.5 V, making it compatible with both 2.5 V/3.3 V and 5 V system rails. Key features include an internal 4 MHz RC oscillator (no external crystal required), 3 general-purpose I/O pins (GP0, GP1, GP2) with individual direction control, an 8-bit real-time clock/counter (TMR0) with 8-bit programmable prescaler, a watchdog timer with its own on-chip RC oscillator for reliable operation, and in-circuit serial programming (ICSP) capability. Power management features include low-power sleep mode, internal weak pull-ups, and configurable I/O wake-up-on-change. The integrated Power-on Reset (POR) and Device Reset Timer (DRT) eliminate the need for external reset circuitry. The PIC10F202 architecture leverages Microchip's enhanced mid-range core with single-cycle instruction execution, providing approximately 2:1 code compression compared to competing 8-bit MCUs. The Harvard-style separate program and data buses allow simultaneous instruction fetch and data access. In-circuit debugging is supported via the ICD interface on dedicated pins, although the small 6-pin package limits debug availability on the smallest variants. Typical applications include low-cost consumer electronics (toys, remote controls, personal care devices), LED lighting controllers, battery chargers, sensor signal conditioning, simple motor control (small fans, vibration motors), and automotive AEC-Q100 subsets (interior lighting, seat controls, accessory modules) where minimal PCB footprint and low unit cost are paramount. The wide 2.0 V to 5.5 V supply range also suits single-cell lithium-ion and two-cell alkaline battery-powered designs. When designing with the PIC10F202T-E/OT, careful pin allocation is essential because the 6-pin SOT-23-6 package exposes only 4 functional I/O/ICSP pins after VDD and VSS. The GP3 pin is input-only and used for ICSP/MCLR, while GP0, GP1, and GP2 are bidirectional. For designs requiring more I/O or peripherals, consider migrating to the pin-compatible PIC10F322 family, which offers more memory and peripherals in the same SOT-23-6 footprint. This page synthesizes distributor pricing, drop-in alternatives from the PIC10F200/PIC10F204/PIC10F220 family, and practical design notes not consolidated in the Microchip datasheet, helping engineers select the right 6-pin Flash MCU for cost-sensitive embedded designs.

見積もり お問い合わせ
PIC10F202T-I/OT - 8-Bit MCU, 768B Flash, 4MHz, SOT-23-6 | Microchip
PIC10F202T-I/OT

PIC10F202T-I/OT - 8-Bit MCU, 768B Flash, 4MHz, SOT-23-6 | Microchip

The Microchip Technology PIC10F202T-I/OT is a 6-pin, 8-bit, fully-static, Flash-based CMOS microcontroller in the PIC10F family, packaged in an industrial-temperature SOT-23-6 (OT) surface-mount form factor. It integrates 768 bytes of Flash program memory, 24 bytes of SRAM data memory, 4 MHz internal oscillator, a 3-channel 8-bit A/D-free comparator, and 4 user-configurable I/O pins in a die small enough to fit behind the world's smallest microcontroller pin count. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory, RAM, peripherals, and I/O on one silicon die. The PIC10F202 belongs to the 8-bit microcontroller category, using a RISC architecture with 33 single-word/single-cycle instructions. Within the broader taxonomy, the PIC10F202 sits under 8-bit MCU -> microcontroller -> embedded controller -> semiconductor IC, occupying the cost-optimized end of the embedded-control market where PCB area and BOM cost dominate design decisions over raw compute performance. Key features include 4 MHz operation (1 µs instruction cycle at 4 MHz FOSC), 2.0V to 5.5V wide operating voltage range, ultra-low power consumption suitable for battery applications, an 8-bit timer/counter (TMR0), a watchdog timer (WDT) with on-chip RC oscillator, in-circuit serial programming (ICSP) via two pins, and 4 bidirectional I/O pins (GP0-GP3). The SOT-23-6 package measures approximately 2.9 mm × 1.6 mm with a max height of 1.0 mm, making it one of the smallest microcontrollers available for mass-production designs. Technical depth: The PIC10F202's RISC core executes one instruction per clock cycle (except branches, which take two), and the 12-bit instruction word yields typical 2:1 code compression versus competing 8-bit CISC architectures. Internal oscillator accuracy is calibrated to within ±1% (typical) at 25°C/5V, eliminating external crystal components and freeing all 6 pins for user I/O or programming. Typical applications include low-cost consumer device logic replacement (discrete logic-to-MCU migration), LED blinkers, simple sensor interfaces, battery-powered toys, and any high-volume cost-sensitive embedded control task. Industrial -40°C to +85°C temperature range supports factory automation peripherals. When designing with this part, always include a 0.1 µF decoupling capacitor as close to VDD as possible, keep GP0 and GP1 traces short for reliable ICSP programming in-circuit, and verify unused-pin configuration (GP3 is input-only, no output driver). Programming requires Microchip's MPLAB X IDE with PICkit or ICD tool support. This page synthesizes distributor stock levels, drop-in alternatives, and design considerations not aggregated on the manufacturer datasheet alone.

見積もり お問い合わせ
PIC10F204-E/MC - 8-bit Flash MCU, 384B, 4MHz, DFN-8 | Microchip
PIC10F204-E/MC

PIC10F204-E/MC - 8-bit Flash MCU, 384B, 4MHz, DFN-8 | Microchip

The Microchip Technology PIC10F204-E/MC is a low-cost, high-performance 8-bit Flash-based CMOS microcontroller in a 6-pin-equivalent 8-VFDFN Exposed Pad package (MC suffix) that delivers 384 bytes of Flash program memory, 16 bytes of SRAM, and 4 I/O pins at speeds up to 4 MHz. It features a RISC architecture with only 33 single-word/single-cycle instructions, all executing in 1 microsecond at 4 MHz except program branches which take two cycles, providing an order-of-magnitude performance advantage over competitive 8-bit microcontrollers in the same price tier. What is an 8-bit Flash microcontroller? An 8-bit Flash microcontroller is a single-chip computer that integrates a CPU, non-volatile Flash program memory, SRAM, and peripherals onto one die and executes instructions on 8-bit-wide data paths. The PIC10F204 belongs to the PIC10F family of 6-pin baseline microcontrollers (PIC -> 8-bit microcontroller -> microcontroller -> semiconductor -> integrated circuit), optimized for low-cost, low-pin-count embedded control where the smallest possible footprint outweighs the need for advanced peripherals. Key features include a wide 2.0V to 5.5V operating voltage range, an internal 4 MHz RC oscillator (no external crystal needed), one analog comparator with absolute reference, 8-bit timer TMR0 with 8-bit programmable prescaler, and a comparator module. The device includes an In-Circuit Serial Programming (ICSP) interface that allows programming after PCB assembly, plus Microchip's nanoWatt Technology power management with idle and sleep modes that drop current consumption below 100 nA in sleep. Architecturally the PIC10F204 uses a Harvard-style RISC core with a 12-bit-wide instruction word, achieving typical 2:1 code compression over other 8-bit MCUs. Its CMOS Flash process allows field re-programmability with 100K endurance cycles minimum and 40-year data retention, while a 256 x 12 program memory layout maps directly onto the 384-byte Flash array. Typical applications include battery-powered sensor nodes, LED drivers and blinkers, simple fan/relay controllers, AC line zero-crossing detectors, and disposable consumer devices where cost dominates. The 8-VFDFN package with exposed thermal pad enables compact surface-mount designs. When designing with this part, choose between the -E (extended -40C to +125C) and -I (industrial -40C to +85C) temperature grades based on the deployment environment, and reserve at least one I/O pin for ICSP programming access during board bring-up. This page synthesizes distributor pricing, verified drop-in alternatives within the same DFN-8 footprint, and practical design notes not found in the manufacturer datasheet alone.

見積もり お問い合わせ