マイクロコントローラ

製品 (18688)

STM32F071CBT7 - 48MHz Cortex-M0 MCU, 128KB Flash | STMicroelectronics
STM32F071CBT7

STM32F071CBT7 - 48MHz Cortex-M0 MCU, 128KB Flash | STMicroelectronics

The STMicroelectronics STM32F071CBT7 is an Arm Cortex-M0 32-bit RISC microcontroller operating at up to 48 MHz, integrating 128 KB of Flash memory and 16 KB of SRAM with hardware parity in a 48-pin LQFP (7x7 mm) package. It is part of the STM32F0 "Access Line" mainstream family and includes a Consumer Electronics Control (CEC) peripheral alongside 12-bit ADC, 12-bit DAC, and 12 timers, all within a 2.0V-3.6V digital supply range. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, memory (Flash for code and SRAM for data), digital peripherals (timers, communication interfaces, GPIO) and analog peripherals (ADC, DAC, comparators) onto one silicon die. The Arm Cortex-M0 is the smallest and most energy-efficient member of the Cortex-M family, designed for deterministic real-time control at low cost and low active current; it implements the Thumb-2 instruction subset and the NVIC (Nested Vectored Interrupt Controller). Within the broader taxonomy, the STM32F071 sits below Cortex-M3/M4/M7 parts in processing performance, but above 8-bit MCUs (8051, AVR, PIC16) in code density, debug tooling, and peripherals - making it the typical "mainstream" choice for cost-sensitive embedded designs. Key differentiating features include: hardware parity-checked SRAM for higher reliability in safety-relevant code, a 32-bit hardware CRC calculation unit (offloading software CRC loops), an integrated HDMI CEC controller for consumer-electronics interoperability, and a 5V-tolerant I/O structure that simplifies interfacing with legacy 5V logic. The 12-bit ADC and 12-bit DAC are 1 MSPS and 1 MSPS respectively, allowing mixed-signal control loops without external converters. Architecture: Cortex-M0 core with single-cycle multiplier, 3-stage pipeline, and SysTick timer; the bus matrix splits I-code, D-code, and system buses to allow parallel Flash fetch and SRAM access. Power management integrates a low-power Run, Sleep, Stop, and Standby modes with RTC retention, and a brown-out reset (BOR) plus a power-on reset (POR) supervisor. Typical applications include USB-CDC virtual COM ports (using the on-chip USB FS device PHY-less with external 1.5 k pull-up), home-appliance control panels, motor-control sub-modules, HDMI-CEC-equipped TV and set-top boxes, and low-cost sensor hubs. The package, 48-LQFP, is a hand-solderable and prototype-friendly footprint that integrates well into both production and hobby boards. Design consideration: the 7 suffixes (T7 = LQFP48 industrial temperature grade, tape-and-reel) require careful selection when migrating between similar STM32F0 part numbers - the operating temperature range, package, and shipping form all vary by suffix. Designers should verify that the target application does not exceed -40C to +85C industrial range. This page synthesizes distributor pricing, drop-in pin-compatible alternatives, and design notes sourced from the STMicroelectronics datasheet (DS9826), which go beyond what the manufacturer PDF alone offers for procurement and second-sourcing decisions.

USD $2.95 在庫あり
STM32F072C8T6 - 48MHz 64KB Cortex-M0 MCU | STMicroelectronics
STM32F072C8T6

STM32F072C8T6 - 48MHz 64KB Cortex-M0 MCU | STMicroelectronics

The STMicroelectronics STM32F072C8T6 is a 32-bit ARM Cortex-M0 microcontroller operating up to 48 MHz, with 64 KB of Flash memory and a 48-LQFP 7 x 7 mm package. It belongs to the STM32F0 microcontroller family and is positioned for compact USB, CAN, general embedded-control, and low-power embedded applications. The supplied distributor information identifies the device as a mainstream ARM Cortex-M0 MCU with USB and CAN connectivity. The STM32F0 family consists of entry-level 32-bit RISC microcontrollers intended to provide efficient control processing, integrated communications, analog peripherals, and flexible memory options in a small surface-mount package. This hierarchy places the STM32F072C8T6 within the broader category of embedded microcontrollers, where the device executes firmware, controls peripherals, and communicates with external hardware. Verified source data identifies a 48 MHz maximum CPU frequency, 64 KB of Flash, and a 48-LQFP package. The distributor descriptions also identify USB and CAN support as defining connectivity features. The 48-pin LQFP format provides a conventional leaded surface-mount footprint suitable for designs requiring accessible pins, compact board area, and straightforward assembly. Exact RAM size, voltage limits, peripheral details, and temperature limits are not supplied in the verified excerpts and are therefore not inferred here. Because the device is an ARM Cortex-M0 microcontroller, software development can use the STM32 family ecosystem and embedded C toolchains. The Cortex-M0 core provides a 32-bit RISC architecture, while the STM32F072x8/xB family description from STMicroelectronics emphasizes high-performance embedded control and integrated peripherals. Toolchain and exact peripheral assignments should be confirmed against the manufacturer datasheet and reference manual for the selected board design. Typical application areas include USB-connected control devices, CAN-connected industrial or automotive interface modules, compact sensor controllers, embedded instrumentation, and general-purpose 48 MHz embedded products. USB and CAN are especially relevant where a controller must combine local real-time processing with a standardized communications link. Designers should verify package pin assignments, power requirements, clock configuration, decoupling, and peripheral availability against the official STM32F072C8T6 documentation before layout release. The verified data confirms the 48-LQFP 7 x 7 mm package and 48 MHz Cortex-M0 performance, but does not provide a verified pinout, recommended capacitor values, or full electrical limits. This product record combines distributor availability information, manufacturer family positioning, interface requirements, package data, and practical selection guidance to support initial design decisions. It is intended to help engineers identify whether the STM32F072C8T6 matches the required microcontroller package, processing speed, Flash capacity, and USB/CAN feature set.

USD $5.44 在庫あり
STM32F072C8T6TR - 48MHz 64KB Cortex-M0 MCU | STMicroelectronics (Tape & Reel)
STM32F072C8T6TR

STM32F072C8T6TR - 48MHz 64KB Cortex-M0 MCU | STMicroelectronics (Tape & Reel)

The STMicroelectronics STM32F072C8T6TR is a 32-bit ARM Cortex-M0 microcontroller operating up to 48 MHz, with 64 KB of Flash memory and a 48-LQFP 7 x 7 mm package. It belongs to the STM32F0 microcontroller family and is positioned for compact USB, CAN, general embedded-control, and low-power embedded applications. The supplied distributor information identifies the device as a mainstream ARM Cortex-M0 MCU with USB and CAN connectivity. The STM32F0 family consists of entry-level 32-bit RISC microcontrollers intended to provide efficient control processing, integrated communications, analog peripherals, and flexible memory options in a small surface-mount package. This hierarchy places the STM32F072C8T6TR within the broader category of embedded microcontrollers, where the device executes firmware, controls peripherals, and communicates with external hardware. Verified source data identifies a 48 MHz maximum CPU frequency, 64 KB of Flash, and a 48-LQFP package. The distributor descriptions also identify USB and CAN support as defining connectivity features. The 48-pin LQFP format provides a conventional leaded surface-mount footprint suitable for designs requiring accessible pins, compact board area, and straightforward assembly. Exact RAM size, voltage limits, peripheral details, and temperature limits are not supplied in the verified excerpts and are therefore not inferred here. Because the device is an ARM Cortex-M0 microcontroller, software development can use the STM32 family ecosystem and embedded C toolchains. The Cortex-M0 core provides a 32-bit RISC architecture, while the STM32F072x8/xB family description from STMicroelectronics emphasizes high-performance embedded control and integrated peripherals. Toolchain and exact peripheral assignments should be confirmed against the manufacturer datasheet and reference manual for the selected board design. Typical application areas include USB-connected control devices, CAN-connected industrial or automotive interface modules, compact sensor controllers, embedded instrumentation, and general-purpose 48 MHz embedded products. USB and CAN are especially relevant where a controller must combine local real-time processing with a standardized communications link. Designers should verify package pin assignments, power requirements, clock configuration, decoupling, and peripheral availability against the official STM32F072C8T6TR documentation before layout release. The verified data confirms the 48-LQFP 7 x 7 mm package and 48 MHz Cortex-M0 performance, but does not provide a verified pinout, recommended capacitor values, or full electrical limits. This product record combines distributor availability information, manufacturer family positioning, interface requirements, package data, and practical selection guidance to support initial design decisions. It is intended to help engineers identify whether the STM32F072C8T6TR matches the required microcontroller package, processing speed, Flash capacity, and USB/CAN feature set.

USD $4.64 在庫あり
STM32F072C8T7 - 48MHz Cortex-M0 MCU with 64KB Flash | STMicroelectronics
STM32F072C8T7

STM32F072C8T7 - 48MHz Cortex-M0 MCU with 64KB Flash | STMicroelectronics

The STMicroelectronics STM32F072C8T7 is a 32-bit ARM Cortex-M0 microcontroller operating up to 48 MHz, with 64 KB of Flash memory and a 48-LQFP 7x7 mm package. It is designed for embedded USB, CAN, mixed-signal, and timer-driven control applications. A microcontroller is a programmable semiconductor device that integrates a processor core, memory, peripherals, and I/O into one compact component. The STM32F072 belongs to the STM32F0 series of 32-bit RISC microcontrollers, combining real-time control capability with USB and CAN connectivity. This hierarchy places it among embedded processors and semiconductor devices used in industrial, consumer, and communications equipment. Verified distributor data identifies the STM32F072C8T7 as a 48-MHz ARM Cortex-M0 MCU with 64 KB Flash and a 48-LQFP package. The listed Mouser description also identifies USB and CAN capability, while the STMicroelectronics datasheet result states that the CAN implementation supports specifications 2.0A and 2.0B at up to 1 Mbit/s. These interfaces make the device suitable for embedded control systems requiring both serial connectivity and deterministic peripheral operation. The STM32F0 architecture is appropriate for low- to medium-complexity embedded products where a low-cost general-purpose core, compact package, and integrated communications peripherals simplify board design. USB support can reduce the need for an external communications controller, while CAN is useful for distributed industrial and vehicle-related control networks. The MCU is positioned for applications that do not require the higher performance or memory bandwidth of an STM32F4-class device. Typical uses include USB-connected sensors, CAN-capable industrial modules, compact motor-control boards, communication adapters, and low-cost embedded instruments. Designers should confirm the exact peripheral assignments, electrical limits, pin multiplexing, and clock-tree requirements against the manufacturer datasheet before finalizing a PCB or firmware design. The STM32F072C8T7 is best chosen when its 48 MHz Cortex-M0 core, 64 KB Flash, USB, CAN, and 48-LQFP footprint align with the target product. A design requiring different memory capacity, package pinout, timing, or peripheral availability should be reviewed before substitution. This page synthesizes distributor listings, manufacturer resources, application guidance, and replacement considerations not found in a single distributor specification table. For a valid replacement, use the manufacturer datasheet and package drawing to confirm pin compatibility rather than relying only on a generic cross-reference result. Verify boot configuration, oscillator requirements, USB and CAN routing, peripheral mapping, supply voltage, and firmware assumptions as part of engineering validation.

見積もり 在庫あり
STM32F072C8U6 - 48MHz Cortex-M0 MCU with USB/CAN | ST
STM32F072C8U6

STM32F072C8U6 - 48MHz Cortex-M0 MCU with USB/CAN | ST

The STMicroelectronics STM32F072C8U6 is a 32-bit ARM Cortex-M0 microcontroller operating up to 48 MHz, with 64 KB of Flash and 16 KB of SRAM, in a 48-UFQFPN 7 x 7 mm package. The device includes USB, CAN, high-speed embedded interfaces, and low-power features for compact embedded control systems. A microcontroller is a programmable semiconductor that integrates a processor core, memory, peripherals, and I/O into one control platform. The STM32F0 family belongs to the ARM Cortex-M microcontroller hierarchy, combining real-time embedded processing with peripherals for communications, timing, analog measurement, and digital control. STM32F072C8U6 is positioned for USB and CAN-connected equipment rather than high-performance computing. Key features include a 48 MHz maximum core frequency, 64 KB Flash memory, 16 KB SRAM, USB connectivity, CAN connectivity, and a 48-pin UFQFPN package. The 3.3 V supply notation in distributor records identifies the intended operating rail for this device. Its integrated communications peripherals can reduce external interface-component count in USB peripheral, CAN network, and industrial-control products. The STM32F072x8/xB architecture uses the high-performance ARM Cortex-M0 32-bit RISC core, as identified by STMicroelectronics in the product-page result. The MCU family is intended for embedded applications requiring moderate processing speed, communications, and low-power operation. USB and CAN support can simplify firmware-driven connectivity, although peripheral configuration and clocking must be validated against the complete manufacturer datasheet. Typical applications include USB-to-serial adapters, CAN-connected sensors, industrial control modules, USB peripheral equipment, and compact consumer electronics. The UFQFPN package supports dense PCB layouts, while the exposed-pad construction requires careful thermal-via and copper layout according to the manufacturer’s land pattern. When designing a board, confirm the exact pin assignments, alternate functions, power requirements, decoupling strategy, and exposed-pad connection from the official datasheet. Do not substitute a mechanically similar MCU solely by package name; verify USB, CAN, peripheral mapping, firmware startup, and memory compatibility. This page combines verified manufacturer and distributor information with compatibility-focused alternative analysis, application guidance, comparison parameters, and practical PCB considerations to support faster engineering evaluation and sourcing.

USD $2.43 在庫あり
STM32F072C8U6TR - 48MHz Cortex-M0 64KB MCU | STMicroelectronics
STM32F072C8U6TR

STM32F072C8U6TR - 48MHz Cortex-M0 64KB MCU | STMicroelectronics

STMicroelectronics STM32F072C8U6TR is a 32-bit ARM Cortex-M0 microcontroller operating at up to 48 MHz, with 64KB of Flash memory and a 48-pin UFQFPN package. The device includes USB and CAN connectivity and provides 37 I/O pins according to the verified product data. Its compact 7 x 7 mm package is intended for space-constrained embedded control, industrial automation, IoT, motor-control, metering, and low-power board designs. The STM32F072C8U6TR combines a general-purpose RISC core with embedded peripherals and connectivity in a single surface-mount device. A microcontroller is a semiconductor device that integrates a processor core, memory, peripherals, and I/O into one component. Within the hierarchy of embedded semiconductors, this MCU belongs to the ARM Cortex-M0 class of general-purpose 32-bit microcontrollers and is used to execute firmware, read sensors, control outputs, and manage communication interfaces. The Cortex-M0 architecture provides a compact instruction set and deterministic embedded-control platform, while the STM32F0 family targets cost-sensitive applications that require more than a basic 8-bit controller. Verified features include a 48 MHz maximum CPU frequency, 64KB Flash organized as 64K x 8, 37 I/O, USB, CAN, and a 48-UFQFPN package with exposed pad. The 48 MHz clock provides additional processing headroom for protocol handling and control tasks compared with slower entry-level MCUs. USB and CAN connectivity can reduce the need for external interface components in connected industrial or embedded products, although the final design must still verify device-specific peripheral configurations. The STM32F072C8U6TR is suited to applications that need moderate control performance, serial communication, and compact packaging. Its 64KB Flash capacity is appropriate for moderate firmware images, while the 48-pin package provides a substantial I/O count for sensors, actuators, communications, and control signals. Because the verified data does not provide RAM size, ADC details, timer resources, voltage limits, temperature range, or exact pin names, those parameters must be confirmed in the manufacturer datasheet before schematic or PCB sign-off. Typical applications include industrial control nodes, USB-connected peripherals, CAN-based automation equipment, IoT sensing nodes, motor-control interfaces, and metering products. The exposed pad should be connected according to the manufacturer land-pattern and thermal guidance. Designers should preserve the required decoupling structure, route sensitive communications carefully, and confirm the exact pin multiplexing before finalizing a board layout. This product data combines verified distributor specifications, manufacturer product information, sourcing links, and engineering selection guidance. It is intended to support initial design decisions, not to replace the complete STM32F072x8/xB datasheet, reference manual, errata documents, or board-level validation.

見積もり 在庫あり
STM32F072C8U7 - 48MHz Cortex-M0 64KB MCU | STMicroelectronics
STM32F072C8U7

STM32F072C8U7 - 48MHz Cortex-M0 64KB MCU | STMicroelectronics

The STMicroelectronics STM32F072C8U7 is a 32-bit ARM Cortex-M0 microcontroller operating up to 48 MHz, with 64KB of Flash memory, in a 48-pin UFQFPN package. The device targets compact embedded systems requiring USB, CAN, general-purpose connectivity, and low-power control. The verified distributor listing identifies the part as a 2.5V/3.3V MCU and describes it as an ARM Cortex-M0 RISC device with USB and CAN support. An STM32F0 microcontroller belongs to the ARM Cortex-M0 class of 32-bit RISC microcontrollers and sits within the broader embedded-microcontroller and semiconductor hierarchy. These devices combine a processor core, Flash program memory, SRAM, peripherals, and GPIO in one integrated component. The STM32F072C8U7 is appropriate when a design needs deterministic embedded control, multiple serial interfaces, and a compact surface-mount footprint rather than a general-purpose host processor. The verified STM32F072C8 specification identifies an operating frequency of up to 48 MHz and 64KB of Flash memory organized as 64K x 8. Distributor listings also identify USB, CAN, and 2.5V/3.3V operation for this device. These features make the MCU relevant to USB peripherals, CAN-connected industrial equipment, USB-to-serial products, compact control boards, and low-cost embedded instruments. The package is specified as 48-UFQFPN, with a 7 mm by 7 mm footprint according to the verified listing. The STM32F072x8/xB family uses the high-performance ARM Cortex-M0 32-bit RISC core. The CAN capability is described by the manufacturer datasheet search result as compliant with specifications 2.0A and 2.0B, supporting standard and extended frames at up to 1 Mbit/s. This makes CAN integration more practical for systems that must exchange diagnostic or control data over a short industrial network. Typical applications include USB-connected data acquisition, CAN-based monitoring, embedded control for communications equipment, compact USB-to-CAN bridges, and low-power industrial modules. The MCU is also relevant to devices requiring a compact 7 mm x 7 mm package and a mainstream Cortex-M0 software ecosystem. Application-specific details such as exact SRAM, GPIO count, peripheral variants, temperature range, and electrical limits require confirmation from the manufacturer datasheet. When designing around the STM32F072C8U7, verify the exact pin assignments, exposed-pad connection, decoupling requirements, clock configuration, and peripheral multiplexing against the official datasheet. USB and CAN interfaces require careful signal-integrity layout, while power design should account for the 2.5V/3.3V supply requirement and regulator tolerance. This page consolidates verified source data and marks unavailable technical details instead of estimating them.

見積もり 在庫あり
STM32F072CBT6 - 48MHz Cortex-M0 MCU with USB/CAN | STMicroelectronics
STM32F072CBT6

STM32F072CBT6 - 48MHz Cortex-M0 MCU with USB/CAN | STMicroelectronics

The STMicroelectronics STM32F072CBT6 is a 32-bit Arm Cortex-M0 microcontroller operating up to 48 MHz, with 128 KB of Flash memory, 16 KB of SRAM, USB, and CAN connectivity in a 48-LQFP 7 x 7 mm package. It targets compact embedded products that need deterministic control, serial communications, and USB connectivity without requiring a larger Cortex-M core. A microcontroller is a programmable semiconductor that integrates a CPU, memory, and peripherals into one device. The STM32F0 family belongs to the Arm Cortex-M0 microcontroller hierarchy, combining low-complexity control with embedded flash, SRAM, communication interfaces, timers, and analog peripherals. This positioning makes it suitable for USB accessories, industrial control nodes, motor-control helpers, and compact consumer equipment. The supplied manufacturer-related listings identify a 32-bit Cortex-M0 core, a maximum frequency of 48 MHz, and 128 KB of Flash memory. The family listing also states that this device family covers 64 KB to 128 KB of Flash and provides 16 KB of SRAM with hardware parity CRC capability. USB and CAN are explicitly identified in distributor product descriptions, providing the main communications features for this application-oriented part. STM32F072CBT6 is the non-tape-and-reel ordering form used within an LQFP-48 package family. The suffix T6 denotes the specified temperature and package qualification arrangement, while the B position identifies the 128 KB Flash variant. Firmware must use the exact device identifier, clock configuration, pin definitions, and peripheral mapping from the applicable STMicroelectronics device documentation rather than treating similarly named STM32 devices as interchangeable by firmware alone. Typical embedded roles include a USB-to-serial or configuration interface, a CAN-connected sensor or actuator node, an industrial keypad controller, a motor-support controller, and a compact data-acquisition front end. The 48 MHz Cortex-M0 processor provides predictable execution for control loops, while the integrated USB and CAN options reduce the need for external interface controllers in suitable designs. A robust design should verify every assigned pin against the exact LQFP-48 pinout, provide the required decoupling and clock components, and confirm USB impedance routing and CAN termination requirements. Firmware migration should be validated at register, peripheral, timing, and low-power levels. A candidate replacement should be treated as a drop-in only after its footprint, pin multiplexing, electrical limits, memory, bootloader, and peripheral behavior have all been verified. This page consolidates the verified distributor specifications, source links, package constraints, and replacement cautions into a practical engineering record. It also separates confirmed facts from unavailable data rather than estimating pin mappings, pricing tiers, lifecycle details, or compliance claims that were not present in the supplied sources.

見積もり 在庫あり
STM32F072CBT6TR - 48MHz Cortex-M0 MCU with USB/CAN
STM32F072CBT6TR

STM32F072CBT6TR - 48MHz Cortex-M0 MCU with USB/CAN

The STMicroelectronics STM32F072CBT6TR is a 32-bit ARM Cortex-M0 STM32F0-series microcontroller operating up to 48 MHz, with 128 KB of Flash memory, 16 KB of SRAM, USB, CAN, and a 48-pin LQFP package measuring 7 x 7 mm. It combines a compact general-purpose MCU architecture with integrated communications and control peripherals for embedded systems. A microcontroller is a semiconductor device that integrates a CPU core, memory, and peripherals into one component. The STM32F0 family belongs to the ARM Cortex-M0 microcontroller segment, combining low-complexity firmware execution with dedicated hardware for communications, timing, analog conversion, and control. The STM32F072CBT6TR is suited to designs requiring USB connectivity, CAN communication, and a moderate amount of embedded Flash and SRAM. The verified product information identifies a 48 MHz ARM Cortex-M0 core, 128 KB Flash, 16 KB SRAM, USB, CAN, and CEC functions. Its 48-pin LQFP package provides a conventional leaded surface-mount format suitable for designs that require accessible pins and straightforward assembly. The 48 MHz operating frequency supports responsive control tasks and communication handling while keeping software complexity aligned with the Cortex-M0 feature set. Typical applications include USB-connected control devices, CAN-based industrial or automotive-adjacent interface modules, embedded data acquisition, consumer peripherals, and compact control boards. USB can simplify host connectivity, while CAN supports robust communication between distributed nodes when the system design follows the applicable CAN electrical and firmware requirements. Designers should verify the complete pinout, electrical limits, clock configuration, and peripheral assignments against the manufacturer datasheet before layout or firmware release. USB and CAN interfaces also require careful connector, routing, grounding, decoupling, and signal-integrity decisions. The LQFP package facilitates inspection but requires adequate assembly clearance and thermal design. This product page combines verified distributor and manufacturer-linked information with engineering-oriented comparison guidance and practical design notes for engineers evaluating STM32F072CBT6TR, STM32F072C8T6TR, and related MCU choices.

見積もり 在庫あり
STM32F072CBT7 - 48MHz Cortex-M0 MCU with USB/CAN | STMicroelectronics
STM32F072CBT7

STM32F072CBT7 - 48MHz Cortex-M0 MCU with USB/CAN | STMicroelectronics

The STMicroelectronics STM32F072CBT7 is a 32-bit ARM Cortex-M0 microcontroller with a 48 MHz CPU, 128 KB of Flash memory, and USB and CAN connectivity, housed in a 48-LQFP 7 x 7 mm package. It belongs to the STM32F0 mainstream MCU family and targets compact embedded systems requiring USB, CAN, and a moderate processing speed. A microcontroller is an integrated circuit that combines a processor core, memory, and peripheral interfaces on one semiconductor device. The STM32F0 series sits within the broader embedded-control hierarchy: MCU -> microcontroller -> embedded processor -> semiconductor. Compared with discrete logic controllers, an MCU provides firmware execution, state management, communication, timing, and direct control of external sensors, actuators, and human-interface circuits. The verified product listing identifies a 48 MHz ARM Cortex-M0 core, 128 KB Flash, USB, CAN, and a 48-LQFP package. The STM32F072CBT7 is therefore suited to USB-enabled control devices, CAN-connected equipment, embedded instrumentation, and compact industrial modules. The exact RAM size, ADC specifications, GPIO count, supply limits, and package dimensions are not included in the supplied verified data and should be confirmed in the manufacturer datasheet before a production design is released. The MCU architecture supports embedded control workloads where deterministic peripheral operation and compact software support matter. USB and CAN are valuable when a design must communicate with a host, service tool, test fixture, or networked peripheral. Compared with a higher-performance Cortex-M system, the Cortex-M0 core provides a simpler embedded platform, while the 48 MHz operating point remains suitable for control loops, protocol handling, user-interface scanning, and supervisory logic. Typical applications include USB-to-control embedded modules, CAN-connected industrial controllers, compact sensor hubs, low-cost communication boards, and battery-powered instrumentation. Designers should provide stable power, decoupling, clock routing, reset handling, and programming access in accordance with the manufacturer reference information. The 48-LQFP package is also relatively easy to inspect and rework compared with very fine-pitch packages. The main engineering trade-off is that the verified listing does not provide a complete electrical and memory map, so firmware planning should be based on the official datasheet and reference manual rather than assumptions. This page consolidates the verified distributor description, package information, sourcing links, and application context while clearly marking unspecified technical data for confirmation.

USD $5.00 在庫あり
STM32F072CBU6 - 48MHz 128KB USB MCU | STMicroelectronics
STM32F072CBU6

STM32F072CBU6 - 48MHz 128KB USB MCU | STMicroelectronics

The STMicroelectronics STM32F072CBU6 is an ARM Cortex-M0 32-bit microcontroller operating up to 48 MHz, with 128 KB of flash memory and a 48-UFQFPN 7 x 7 mm package. It combines a USB full-speed device interface, CAN, 12-bit ADC, 12-bit DAC, and multiple 16-bit and 32-bit timers in one compact embedded-control device. A microcontroller is a programmable integrated circuit that executes firmware, reads sensor and control inputs, and drives outputs within an embedded system. The STM32F072 belongs to the STM32F0 value-line family of 32-bit microcontrollers and provides a practical balance of processing speed, connectivity, analog resources, memory, and package density for compact control systems. Key verified features include the 48 MHz ARM Cortex-M0 core, 128 KB flash, one USB full-speed device port, one CAN interface, one 12-bit ADC, and one two-channel 12-bit DAC. The source material also identifies seven 16-bit timers and one 32-bit timer. These resources support USB-connected peripherals, industrial or automotive communication, analog signal acquisition, precision control outputs, and embedded human-interface designs. The STM32F0 architecture supports efficient real-time control while retaining a straightforward 32-bit instruction set. Its combination of USB, CAN, dual-resolution analog conversion, and timers permits multiple peripherals to share one device. Firmware support and peripheral configuration must still be reviewed for each application because alternate-function mapping, clock settings, low-power behavior, and analog limits affect the final design. Typical uses include USB data acquisition, CAN-connected sensors, motor and actuator control, industrial interface modules, compact instruments, and low-cost embedded platforms. In each case, the 48 MHz core provides computational headroom, while the 7 x 7 mm UFQFPN package supports compact board layouts when pad geometry, exposed-pad soldering, and signal integrity are handled correctly. Designers should route USB and high-speed or sensitive analog signals with short return paths, provide the required bypass and interface components, and verify pin multiplexing before final routing. Firmware migration from another STM32 family should also be tested because peripheral behavior, register details, and application-specific timing may differ even when the physical package is retained. This product record combines the verified distributor and manufacturer information with practical interface and replacement guidance. It distinguishes verified facts from unspecified electrical limits, identifies packaging and sourcing information, and emphasizes the need to verify firmware, pin multiplexing, and manufacturer documentation before production use.

見積もり 在庫あり
STM32F072CBU6TR - 48MHz Cortex-M0 MCU | STMicroelectronics
STM32F072CBU6TR

STM32F072CBU6TR - 48MHz Cortex-M0 MCU | STMicroelectronics

The STMicroelectronics STM32F072CBU6TR is an ARM Cortex-M0 32-bit RISC microcontroller operating at up to 48 MHz, with 128 KB of Flash memory and USB, CAN, and peripheral connectivity, housed in a 48-pin UFQFPN 7 x 7 mm package. The STM32F072x8/xB family combines a 32-bit MCU core, embedded memory, communication interfaces, and low-power control in one compact surface-mount device. Its 48-pin UFQFPN package is intended for space-constrained embedded systems requiring more GPIO and communication options than smaller STM32 packages. An MCU is a programmable integrated circuit used to monitor inputs, execute firmware, control outputs, and manage communication between sensors, actuators, communications links, and human-facing systems. The STM32F072x8/xB family is positioned within the STM32 microcontroller portfolio for embedded control, connectivity, and USB-enabled designs. According to the STMicroelectronics product page, the family uses the high-performance ARM Cortex-M0 core and operates at up to 48 MHz. Key verified features include a 32-bit architecture, 48 MHz maximum operating frequency, and 128 KB of Flash memory described by DigiKey as 128K x 8. Mouser identifies the device as an MCU in the USB line with USB, CAN, 128 KB of Flash, and a 48 MHz CPU. These interfaces support designs that need local control together with wired USB or CAN connectivity, although the exact peripheral availability and operating limits should be confirmed against the manufacturer datasheet for the selected ordering code. The device uses a 48-pin UFQFPN package with an exposed-pad-centered 7 x 7 mm format. The UFQFPN is a surface-mount package family that supports compact PCB layouts while providing many external connection points. Exact pin names, exposed-pad connections, electrical limits, and recommended decoupling values are not included in the supplied web excerpts and are marked as data needed where necessary rather than inferred. Typical applications include USB-connected embedded controllers, CAN-connected industrial or automotive peripheral nodes, sensor-hub systems, compact control boards, and low-power monitoring products. The 48 MHz Cortex-M0 core is suitable for real-time control loops, while USB and CAN support interfaces to host computers, test equipment, or other embedded controllers. For PCB design, place required bypass capacitors close to the supply pins, follow the exposed-pad land pattern and thermal-via recommendations in the manufacturer package drawing, and confirm the pin multiplexing and alternate-function assignments before finalizing firmware. This page combines the verified distributor and manufacturer information with procurement guidance and engineering-oriented selection notes.

USD $3.14 在庫あり
STM32F072CBU7 - 48MHz Cortex-M0 USB MCU | STMicroelectronics
STM32F072CBU7

STM32F072CBU7 - 48MHz Cortex-M0 USB MCU | STMicroelectronics

The STMicroelectronics STM32F072CBU7 is an ARM Cortex-M0 32-bit microcontroller operating up to 48 MHz, with 128 KB of flash memory and USB, CAN, and embedded connectivity in a 48-pin UFQFPN package measuring 7 x 7 mm. It is designed for compact embedded systems requiring USB device connectivity and CAN communication. A microcontroller is a programmable semiconductor that integrates a CPU core, memory, peripherals, and communication interfaces on one integrated circuit. The STM32F072CBU7 belongs to the STM32F0 family of ARM Cortex-M0 embedded processors, combining a low-complexity RISC architecture with serial connectivity and real-time peripherals. Its 32-bit instruction set and integrated flash support compact firmware for control, data acquisition, and communication functions. The verified source data identifies the device as an ARM Cortex-M0 MCU with 128 KB flash, 48 MHz maximum operating frequency, USB, and CAN support. The part is supplied in a 48-UFQFPN 7 x 7 mm package. Arrow additionally identifies the STM32F072CBU7 as a 2.5 V or 3.3 V, 48-pin UFQFPN device with an exposed pad and tray packaging. Other electrical limits, RAM capacity, peripheral details, pin assignments, and temperature ratings were not included in the supplied evidence and require confirmation from the manufacturer datasheet. Typical applications include USB-connected control equipment, industrial monitoring, low-speed CAN network nodes, data loggers, human-interface equipment, and compact embedded control platforms. USB is useful for configuration, firmware updates, and data exchange with a host computer, while CAN supports robust communication between embedded nodes in industrial or automotive-adjacent systems. The 48 MHz Cortex-M0 core provides a practical balance between processing capability, power efficiency, and software simplicity. Designers should verify the complete pinout, exposed-pad connection, decoupling requirements, clock configuration, and peripheral electrical limits against the official STMicroelectronics datasheet before layout. USB signal routing, especially differential impedance and grounding, requires careful PCB planning. The verified distributor records do not provide a complete datasheet-derived electrical table, so unverified current, voltage, memory, timing, and compliance claims should not be assumed. This product record combines verified distributor identification, manufacturer-family information, practical application context, and source-linked comparison data for engineers evaluating the STM32F072CBU7.

USD $6.07 在庫あり
STM32F072CBY6TR - 48MHz Cortex-M0 128KB MCU | STMicroelectronics
STM32F072CBY6TR

STM32F072CBY6TR - 48MHz Cortex-M0 128KB MCU | STMicroelectronics

STMicroelectronics STM32F072CBY6TR is an ARM Cortex-M0 32-bit STM32F0 series microcontroller operating at 48 MHz, with 128 KB of flash memory in a 49-WLCSP package. The verified distributor data identifies USB, CAN, a 2.5 V or 3.3 V supply context, and a 49-pin WLCSP tape-and-reel package. It is a compact embedded-control MCU for applications requiring integrated connectivity and peripheral support without a larger leaded package. What is an STM32F0 microcontroller? An MCU is a semiconductor that combines a processor core, flash memory, RAM, clocks, and peripherals on one integrated circuit. The STM32F0 family is based on the ARM Cortex-M0 processor, a low-complexity 32-bit architecture intended for cost-sensitive embedded control. USB and CAN connectivity place the STM32F072CBY6TR above a basic GPIO-only controller while retaining the STM32F0 focus on compact embedded systems. The verified product data identifies a 48 MHz ARM Cortex-M0 core and 128 KB (128 K x 8) flash. Mouser describes the device as an STM32F0 USB-line MCU with USB and CAN support, while distributor listings identify the 49-WLCSP package. Exact RAM size, GPIO count, ADC ratings, timer details, voltage limits, and package dimensions are not included in the supplied source data and therefore require confirmation from the manufacturer documentation before a design release. The architecture is suited to USB-connected peripherals, CAN nodes, compact industrial controls, and low-cost embedded products. A 48 MHz Cortex-M0 core provides the timing baseline for protocol handling and control tasks, while the integrated USB and CAN interfaces reduce the need for external communication controllers. Designers must still budget peripheral pins, clocks, decoupling, signal integrity, and firmware configuration according to the actual board requirements. Typical use includes a USB-to-serial or configuration interface, a CAN-connected sensor node, a compact industrial controller, a USB peripheral, and a small consumer-device control module. The 49-WLCSP format is especially useful when board area is constrained, but its fine pitch requires careful PCB design, inspection, and assembly capability. Confirm the exposed-pad and ball assignments in the official pinout before layout. When designing around STM32F072CBY6TR, use the manufacturer datasheet for the definitive electrical limits, memory map, peripheral multiplexing, clock tree, and package drawing. Place required decoupling close to the device, preserve USB impedance-controlled routing, and validate CAN termination and transceiver interface layout. The supplied web results support sourcing and identity, but they do not provide every electrical value needed for a complete production design. This page combines verified distributor identity, package, processor, flash, connectivity, and commercial-search information with explicit engineering caveats. It is intended to support initial component selection and sourcing, while signaling which technical details must be checked against the official STMicroelectronics documentation before schematic sign-off or firmware deployment.

USD $5.10 在庫あり
STM32F072R8T6 - 48MHz Cortex-M0 64KB MCU | STMicroelectronics
STM32F072R8T6

STM32F072R8T6 - 48MHz Cortex-M0 64KB MCU | STMicroelectronics

The STMicroelectronics STM32F072R8T6 is an ARM Cortex-M0 32-bit RISC microcontroller operating up to 48 MHz, with 64 KB of Flash memory and 16 KB of SRAM, in a 64-LQFP 10 x 10 mm package. It belongs to the STM32F0 mainstream MCU family and integrates USB, CAN, GPIO, timers, communication peripherals, and low-power features for embedded control designs. A microcontroller is a programmable semiconductor device that combines a processor core, memory, and peripherals on one integrated circuit. In the hierarchy of embedded semiconductors, the STM32F072R8T6 is a general-purpose MCU, while its ARM Cortex-M0 core provides deterministic 32-bit instruction execution for real-time control, communication, and human-interface applications. Verified listing information identifies the device as a 48 MHz ARM Cortex-M0 MCU with 64 KB Flash, 16 KB SRAM, USB, CAN, and a 64-LQFP package. The STM32F0 family is suited to USB-enabled peripherals, CAN-connected equipment, industrial control modules, motor-control support, sensor nodes, and cost-constrained consumer products. Its 2 V to 3.6 V operating range, as reported by the verified search data, supports common embedded supply systems. The STM32F072x8/xB device family combines high-performance processing with embedded peripherals and flexible memory options. The USB interface and CAN capability are important differentiators for designs that need device connectivity alongside general-purpose control. Exact peripheral counts, pin names, electrical limits, and timing values must be confirmed in the manufacturer datasheet before a production design is released. Typical applications include USB-to-serial accessories, CAN gateway boards, motor-control and actuator electronics, industrial sensors, instrumentation, and low-power embedded controllers. Designers should preserve the recommended decoupling and routing practices, provide a stable clock and reset implementation, and verify all unused pins against the selected package pinout. A key design consideration is that firmware compatibility is not guaranteed merely because another MCU has a similar peripheral set. Migration requires checking startup code, memory-map assumptions, interrupt priorities, clock trees, USB or CAN configuration, and package-level pin assignments. The STM32F072R8T6 is best selected when its verified 64 KB Flash, 48 MHz core, 16 KB SRAM, USB, and CAN combination matches the system requirements. This page combines the verified manufacturer and distributor listing information with package-aware engineering context, application guidance, and replacement checks. Because the supplied search results do not include complete manufacturer electrical tables or a verified pin-by-pin mapping, unavailable values are explicitly marked rather than inferred.

見積もり 在庫あり
STM32F072R8T6TR - 48MHz 64KB Cortex-M0 MCU | STMicroelectronics
STM32F072R8T6TR

STM32F072R8T6TR - 48MHz 64KB Cortex-M0 MCU | STMicroelectronics

The STMicroelectronics STM32F072R8T6TR is a 32-bit ARM Cortex-M0 microcontroller operating at up to 48 MHz, with 64 KB of Flash memory and a 64-LQFP 10 x 10 mm package. The device is designed for compact embedded control systems requiring efficient processing, USB connectivity, and a broad set of peripherals. An ARM Cortex-M0 microcontroller is a 32-bit reduced-instruction-set controller used as the central processing unit of embedded products. It combines a low-power architecture with deterministic peripheral access and occupies the microcontroller hierarchy above general-purpose semiconductor logic. The STM32F072 series supports embedded control, connectivity, data acquisition, and low-cost human-interface applications. Verified distributor data identifies a 32-bit architecture, a maximum frequency of 48 MHz, 64 KB Flash organized as 64K x 8, and a 64-LQFP package measuring 10 x 10 mm. These specifications make the part suitable for main-embedded-control designs that need more capability than a basic 8-bit controller while retaining a small package and established STM32 tooling ecosystem. The STM32F072 family is positioned as a high-performance STM32F0-series MCU with embedded ARM Cortex-M0 processing. The STM32F072R8T6TR ordering code identifies the Flash-density, package, temperature, and tape-and-reel variants; the verified source confirms the 64-LQFP package and 64 KB Flash configuration. Typical applications include USB-connected peripheral control, compact data-acquisition equipment, industrial control modules, consumer accessories, and embedded instruments. Designers should confirm peripheral availability, pin multiplexing, operating voltage, timing, and temperature limits in the manufacturer datasheet before releasing a production design. The 10 x 10 mm LQFP package provides accessible leads for assembly and inspection while supporting a higher pin count than small leadless packages. Layout must preserve adequate decoupling, clock integrity, USB signal routing, and programming access. This page consolidates verified manufacturer and distributor information, practical application context, sourcing questions, and package-aware engineering guidance so engineers can evaluate the STM32F072R8T6TR efficiently.

見積もり 在庫あり
STM32F072R8T7 - 48MHz Cortex-M0 MCU with 64KB Flash | STMicroelectronics
STM32F072R8T7

STM32F072R8T7 - 48MHz Cortex-M0 MCU with 64KB Flash | STMicroelectronics

The STMicroelectronics STM32F072R8T7 is an ARM Cortex-M0 32-bit microcontroller operating at up to 48 MHz, with 64 KB of Flash memory and USB, CAN, and embedded connectivity features, housed in a 64-LQFP 10 x 10 mm package. A microcontroller is a programmable integrated circuit that combines a processor core, memory, peripherals, and communication interfaces on one semiconductor device. The STM32F0 family belongs to the embedded-processor hierarchy and is intended for compact control systems, connected products, industrial equipment, and USB-enabled peripherals. Its 32-bit ARM Cortex-M0 core provides a common instruction set and development ecosystem for embedded firmware development. The STM32F072R8T7 combines 64 KB Flash with a 48 MHz maximum operating frequency. The verified distributor listing identifies USB and CAN connectivity, while the official STMicroelectronics page identifies the STM32F072x8/xB device family. These interfaces make the device relevant to designs requiring USB device connectivity, CAN communication, or embedded control without using a larger microcontroller package. The STM32F072R8T7 is packaged as a 64-LQFP 10 x 10 mm device. The R8 designation is associated with the STM32F072x8 family, and the T7 ordering suffix identifies the supplied temperature and packaging configuration. Exact operating voltage limits, RAM capacity, GPIO count, ADC specifications, clock details, and electrical limits were not included in the supplied verified excerpts and are therefore not inferred here. Typical application domains include USB-enabled control devices, CAN-connected industrial or embedded systems, sensor-control platforms, communication peripherals, and compact consumer equipment. In a USB peripheral, the MCU can manage device communication alongside application logic; in a CAN node, it can combine control processing with bus connectivity. The 48 MHz core provides a defined performance target for firmware scheduling and peripheral control. For PCB design, use the manufacturer pinout and package drawing, confirm the exact LQFP land pattern, route USB and CAN signals according to their interface requirements, and validate power, decoupling, clock, and exposed-pad connections against the complete manufacturer datasheet. This page summarizes verified distributor and manufacturer information, supported connectivity, package data, and procurement sources without guessing undocumented electrical values.

見積もり 在庫あり
STM32F072RBH6 - 48MHz Cortex-M0 128KB MCU | STMicroelectronics
STM32F072RBH6

STM32F072RBH6 - 48MHz Cortex-M0 128KB MCU | STMicroelectronics

The STMicroelectronics STM32F072RBH6 is a 32-bit ARM Cortex-M0 microcontroller operating at 48 MHz, with 128 KB of Flash memory, 16 KB of SRAM, USB, CAN, and CEC connectivity, and a 64-pin UFBGA package measuring 5 mm by 5 mm. Designed for compact embedded systems, this STM32F0 device combines a low-cost microcontroller platform with USB and CAN support in a very small package. A microcontroller is a semiconductor device that integrates a processor core, memory, peripherals, and communication interfaces into one embedded-control component. The ARM Cortex-M0 core uses a compact instruction set intended for cost-sensitive applications, while the STM32F072RBH6 adds 128 KB of Flash for firmware and 16 KB of SRAM for working data. USB, CAN, and CEC interfaces allow the device to connect to host systems, industrial networks, and consumer-electronics control signals. Key verified features include a 32-bit ARM Cortex-M0 core, a maximum CPU frequency of 48 MHz, 128 KB of 128 K x 8 Flash, and 16 KB of SRAM. The device is identified as a mainstream USB-line MCU with CAN and CEC functions. Its 64-UFBGA package supports compact board layouts, but the dense 5 mm by 5 mm land pattern requires careful PCB design, inspection, and assembly planning. The STM32F072RBH6 belongs to the STM32F0 family and is positioned between simple control MCUs and more highly integrated connectivity devices. Its combination of USB and CAN is useful for portable accessories, industrial monitoring nodes, USB-to-CAN gateways, and embedded human-interface systems. The exact peripheral configuration, operating-temperature range, voltage limits, pin functions, and electrical timing values require confirmation from the manufacturer datasheet. Typical applications include USB-connected control devices, CAN-based industrial or automotive-adjacent monitoring equipment, consumer peripherals, low-cost embedded controllers, and compact sensor-interface products. Firmware development should use the STM32F0 toolchain and account for the package's fine-pitch ball assignment and exposed-pad requirements. For a new design, verify every ball assignment, power domain, decoupling requirement, and exposed-pad connection against the official STM32F072RBH6 documentation before layout release. Because the verified search results identify the package as 64-UFBGA (5 x 5), use the exact manufacturer land pattern rather than a generic 64-pin QFN footprint. This product page consolidates distributor specifications, source links, procurement information, and engineering-oriented usage guidance for the STM32F072RBH6. It is intended to support initial component selection while directing engineers to the official STMicroelectronics datasheet for authoritative pinout, electrical, and reliability data.

見積もり 在庫あり
STM32F072RBT6 - 48MHz Cortex-M0 MCU, 128KB Flash, USB/CAN | ST
STM32F072RBT6

STM32F072RBT6 - 48MHz Cortex-M0 MCU, 128KB Flash, USB/CAN | ST

The STMicroelectronics STM32F072RBT6 is a 32-bit ARM Cortex-M0 mainstream microcontroller operating at up to 48 MHz, integrating 128 KB of embedded Flash and 16 KB of SRAM in a 64-pin LQFP (10x10 mm) surface-mount package. A microcontroller (MCU) is a single integrated circuit that combines a processor core, memory, and programmable peripherals on one die, sitting at the lowest level of the embedded-system hierarchy: MCU -> embedded processor -> computing system. The STM32F0 series is positioned inside ST's broader STM32 family of ARM-based 32-bit MCUs, targeting cost-sensitive mainstream designs that still require modern connectivity such as USB and CAN. Key specifications of the STM32F072RBT6 include a crystal-less USB 2.0 full-speed device interface, which eliminates the need for an external USB clock crystal and reduces bill-of-materials cost and PCB area, plus a CAN bus controller, HDMI-CEC hardware, and up to 51 general-purpose I/O pins in the 64-LQFP package, many of them 5V-tolerant for direct legacy interfacing. The device also embeds a 12-bit 1 Msps ADC, a 12-bit DAC, multiple 16-bit and 32-bit timers, USART, SPI, I2C, and support for low-power Sleep, Stop and Standby modes. Architecturally, the STM32F072RBT6 is built around the high-performance ARM Cortex-M0 32-bit RISC core with single-cycle I/O access, executing the Thumb-2 instruction set at up to 48 MHz (1.25 DMIPS/MHz). The internal bus matrix connects the core to Flash, SRAM, and peripherals via AHB and APB bridges, while the clock tree is driven by an internal 8 MHz RC and a 48 MHz RC that supports the USB clock domain directly, which is what enables crystal-less USB operation. Typical applications include USB device accessories (HID keyboards, game controllers, USB-C debug probes), CAN-based industrial nodes and automotive-adjacent peripherals, motor control and consumer appliances, and smart-home IoT endpoints where the combination of USB, CAN, and rich 5V-tolerant GPIO density all in a 64-LQFP fits a wide range of mainstream designs. When designing with this part, note that the crystal-less USB relies on the internal 48 MHz HSI48 clock, so compliance testing against USB-IF limits should be planned early; for designs needing tighter USB jitter, an external crystal can be tied to the OSC pins. Also, the 5V-tolerant I/Os are tolerant only when the related VDD is present - do not back-power unpowered banks. This page synthesizes distributor pricing context, drop-in alternative analysis, and practical design notes not found in the manufacturer datasheet, providing information gain for engineers comparing STM32F0 options against NXP LPC, GigaDevice GD32, and other Cortex-M0 mainstream MCUs.

USD $2.05 在庫あり
STM32F072RBT6TR - 48MHz Cortex-M0 MCU, 128KB Flash, USB/CAN | ST (Tape & Reel)
STM32F072RBT6TR

STM32F072RBT6TR - 48MHz Cortex-M0 MCU, 128KB Flash, USB/CAN | ST (Tape & Reel)

The STMicroelectronics STM32F072RBT6TR is a 32-bit ARM Cortex-M0 mainstream microcontroller operating at up to 48 MHz, integrating 128 KB of embedded Flash and 16 KB of SRAM in a 64-pin LQFP (10x10 mm) surface-mount package. A microcontroller (MCU) is a single integrated circuit that combines a processor core, memory, and programmable peripherals on one die, sitting at the lowest level of the embedded-system hierarchy: MCU -> embedded processor -> computing system. The STM32F0 series is positioned inside ST's broader STM32 family of ARM-based 32-bit MCUs, targeting cost-sensitive mainstream designs that still require modern connectivity such as USB and CAN. Key specifications of the STM32F072RBT6TR include a crystal-less USB 2.0 full-speed device interface, which eliminates the need for an external USB clock crystal and reduces bill-of-materials cost and PCB area, plus a CAN bus controller, HDMI-CEC hardware, and up to 51 general-purpose I/O pins in the 64-LQFP package, many of them 5V-tolerant for direct legacy interfacing. The device also embeds a 12-bit 1 Msps ADC, a 12-bit DAC, multiple 16-bit and 32-bit timers, USART, SPI, I2C, and support for low-power Sleep, Stop and Standby modes. Architecturally, the STM32F072RBT6TR is built around the high-performance ARM Cortex-M0 32-bit RISC core with single-cycle I/O access, executing the Thumb-2 instruction set at up to 48 MHz (1.25 DMIPS/MHz). The internal bus matrix connects the core to Flash, SRAM, and peripherals via AHB and APB bridges, while the clock tree is driven by an internal 8 MHz RC and a 48 MHz RC that supports the USB clock domain directly, which is what enables crystal-less USB operation. Typical applications include USB device accessories (HID keyboards, game controllers, USB-C debug probes), CAN-based industrial nodes and automotive-adjacent peripherals, motor control and consumer appliances, and smart-home IoT endpoints where the combination of USB, CAN, and rich 5V-tolerant GPIO density all in a 64-LQFP fits a wide range of mainstream designs. When designing with this part, note that the crystal-less USB relies on the internal 48 MHz HSI48 clock, so compliance testing against USB-IF limits should be planned early; for designs needing tighter USB jitter, an external crystal can be tied to the OSC pins. Also, the 5V-tolerant I/Os are tolerant only when the related VDD is present - do not back-power unpowered banks. This page synthesizes distributor pricing context, drop-in alternative analysis, and practical design notes not found in the manufacturer datasheet, providing information gain for engineers comparing STM32F0 options against NXP LPC, GigaDevice GD32, and other Cortex-M0 mainstream MCUs.

USD $2.05 在庫あり
STM32F072RBT7 - 48MHz Cortex-M0 128KB MCU | STMicroelectronics
STM32F072RBT7

STM32F072RBT7 - 48MHz Cortex-M0 128KB MCU | STMicroelectronics

The STMicroelectronics STM32F072RBT7 is a 32-bit ARM Cortex-M0 microcontroller operating at up to 48 MHz, with 128 KB of embedded Flash memory and a 64-LQFP 10 mm × 10 mm package. The verified distributor data identifies USB, CAN, a 2.5 V or 3.3 V supply context, and 64 pins. These characteristics place it in the STM32F0 family of low-complexity embedded microcontrollers for compact control, connectivity, and industrial designs. A microcontroller is a semiconductor device that integrates a processor core, program memory, data memory, peripherals, and I/O into one embedded-control platform. The STM32F0 series belongs to the ARM Cortex-M microcontroller hierarchy and combines a low-complexity 32-bit instruction set with dedicated communication and timing peripherals. This makes the STM32F072RBT7 suitable for systems that need deterministic control without a higher-performance application processor. The STM32F072RBT7 combines a 48 MHz ARM Cortex-M0 core with 128 KB of Flash. Verified distributor records also identify USB and CAN connectivity, which can reduce the need for external interface controllers in connected equipment. Its 64-LQFP package provides 64 physical pins and is suitable for through-hole assembly or mixed-technology PCB layouts where a fine-pitch BGA package would be unnecessary. The available evidence confirms a mainstream STM32F0-series product with USB and CAN support, 128 KB Flash, and operation up to 48 MHz. Detailed peripheral assignments, SRAM capacity, voltage limits, pin functions, bootloader behavior, and electrical timing values are not included in the supplied verified data. Those parameters must be confirmed in the manufacturer datasheet before final schematic or firmware release. Typical uses include USB-connected control accessories, CAN-based industrial nodes, compact motor and actuator controllers, sensor-hub boards, and general embedded products where a 32-bit ARM Cortex-M0 MCU is sufficient. The 64-LQFP package is particularly useful when production teams prefer visible solder joints and straightforward inspection. The main design consideration is interface assignment. USB, CAN, oscillators, reset, programming pins, and general-purpose I/O must be mapped against the manufacturer pinout and application requirements before PCB routing. Firmware support, clock configuration, transceiver requirements, and USB or CAN bus protection are outside the supplied data and should be verified against the official documentation. This page consolidates verified manufacturer and distributor information, technical search coverage, pricing context, and design-oriented interpretation. It does not infer undocumented electrical values, and it distinguishes confirmed specifications from data that still requires engineer verification.

USD $5.42 在庫あり
STM32F072V8H6 - 48MHz Cortex-M0 64KB MCU | STMicroelectronics
STM32F072V8H6

STM32F072V8H6 - 48MHz Cortex-M0 64KB MCU | STMicroelectronics

The STMicroelectronics STM32F072V8H6 is a 32-bit ARM Cortex-M0 microcontroller with a 48 MHz operating frequency, 64 KB Flash memory, and a 100-UFBGA 7 x 7 mm package. The device is part of the STM32F0 mainstream MCU family and includes USB, CAN, and embedded-control connectivity according to the verified distributor descriptions. Its compact package and 64K x 8 Flash organization make it suitable for compact USB, CAN, industrial, and embedded control systems where integration and deterministic performance matter. The STM32F072x8/xB family combines a high-performance Cortex-M0 core with embedded memory and peripheral connectivity in a low-footprint device. A microcontroller is a semiconductor device that integrates a processor core, Flash program memory, SRAM, peripherals, and interface controllers into one component. In the hierarchy of semiconductor components, an MCU sits below embedded processor and general-purpose controller categories and above application-specific control devices. The STM32F072V8H6 is therefore positioned between simple fixed-function controllers and higher-performance microprocessors, providing a programmable platform for control loops, communications, and peripheral coordination. Key verified characteristics include the ARM Cortex-M0 core, 32-bit architecture, 48 MHz maximum operating frequency, 64 KB Flash memory, and 100-UFBGA packaging. The product listing also identifies USB, CAN, and an embedded-control-oriented STM32F0 platform. These features make the MCU appropriate for USB-connected peripherals, CAN nodes, industrial interfaces, and compact control products. Compared with a discrete controller, the integrated MCU reduces the number of external components required for processing, firmware storage, communication, and control. The 100-UFBGA package is a compact surface-mount ball-grid package. Ball-grid construction supports dense PCB routing when the board area is constrained, but assembly and inspection require processes suitable for fine-pitch BGA packages. The 7 x 7 mm package should be laid out according to STMicroelectronics land-pattern and assembly guidance rather than treated as a generic QFN footprint. Exact electrical limits, pin names, memory sizes beyond the verified Flash figure, and peripheral details should be confirmed in the manufacturer datasheet. Typical applications include USB peripherals, CAN communication endpoints, industrial automation modules, compact motor-control boards, and low-cost USB power or data products. In each case, the 48 MHz Cortex-M0 core provides the processing baseline for real-time control, while USB and CAN connectivity reduce the need for external interface components. The 64 KB Flash capacity is most appropriate for firmware that requires moderate code density and local storage rather than large application images. Designers should verify the exact package pinout, exposed-ball assignments, power requirements, clock configuration, decoupling, and programming interface against the official STM32F072x8/xB datasheet. BGA assembly should include adequate thermal and electrical design checks. This page consolidates the verified manufacturer and distributor descriptions, package information, pricing references, cross-reference results, and engineering guidance while clearly identifying information that was not supplied by the source data.

USD $2.31 在庫あり
STM32F072V8T6 - 48MHz 64KB Cortex-M0 MCU | STMicroelectronics
STM32F072V8T6

STM32F072V8T6 - 48MHz 64KB Cortex-M0 MCU | STMicroelectronics

The STMicroelectronics STM32F072V8T6 is a 32-bit ARM Cortex-M0 microcontroller operating at up to 48 MHz, with 64 KB of Flash memory and 16 KB of SRAM, supplied in a 100-pin LQFP package measuring 14 x 14 mm. The STM32F072V8T6 combines a low-power embedded design with USB, CAN, ADC, DAC, timers, and serial communication peripherals. According to the verified distributor and manufacturer listings, it is an STM32F0-series MCU designed for embedded control, connectivity, and signal-processing applications. Its 48 MHz Cortex-M0 core provides deterministic instruction throughput for control loops, while the STM32 family ecosystem provides extensive firmware, peripheral, and development-tool support. What is an STM32F0-series microcontroller? It is a 32-bit embedded microcontroller, a category of microcontroller and semiconductor device used to monitor sensors, operate actuators, process data, and control communication interfaces. The STM32F072V8T6 belongs to the STM32 family hierarchy: STM32F072V8T6 > STM32F0 series > STM32 family > ARM Cortex-M0 microcontroller > embedded processor > semiconductor. Its combination of USB and CAN connectivity is useful for industrial control, USB peripherals, automotive-style communication subsystems, and compact consumer equipment. Key verified features include a 32-bit ARM Cortex-M0 core, a maximum 48 MHz operating frequency, 64 KB Flash, and 16 KB SRAM. The listed package is 100-LQFP, 14 x 14 mm, providing a larger pin count than lower-density STM32 packages and exposing more GPIO and peripheral options. The device is identified by distributor sources as a USB-line MCU with USB, CAN, and communication interfaces. The verified Mouser listing specifically identifies the part as an ARM Cortex-M0 USB-line MCU with 64 KB Flash, USB, and CAN. The STM32F072V8T6 architecture combines a compact general-purpose core with dedicated peripherals for analog measurement, timing, communications, and control. USB and CAN support can reduce the need for separate interface devices in connected embedded systems. The 100-LQFP package is useful when a design requires more externally accessible pins than smaller packages provide, while its 14 x 14 mm footprint remains compact compared with many higher-pin-count packages. The exact ADC, DAC, timer, voltage, and pin-level parameters are not present in the supplied verified snippets, so those values are marked as data needed rather than inferred. Typical applications include USB-connected data acquisition, industrial sensor controllers, CAN-based equipment, motor and actuator control, embedded gateways, and compact automation products. For USB applications, the MCU can manage device communication alongside timers and analog functions. For CAN-based systems, it can combine network communication with local control and data processing. Compared with a simpler microcontroller, its USB and CAN integration can reduce component count, although firmware, peripheral configuration, and device-specific validation remain necessary. The primary design consideration is package planning. A 100-LQFP footprint is not interchangeable with smaller STM32 packages without a PCB redesign, so power, ground, decoupling, signal-routing, and programming access must be planned against the verified 100-pin package. Firmware should also be validated against the exact STM32F072V8T6 datasheet, especially for pin multiplexing, peripheral electrical limits, clock configuration, and USB/CAN timing. Pricing shown in the verified LCSC result is $2.7757 as of 2026-10-22; distributor availability and prices can change. This product data page combines the verified manufacturer and distributor identity, 48 MHz Cortex-M0 positioning, 64 KB Flash, 16 KB SRAM, USB, CAN, and the 100-LQFP package with practical sourcing and design context. It does not infer unreported electrical limits or claim a substitute part unless the supplied cross-reference evidence establishes same-package compatibility.

USD $2.78 在庫あり
STM32F072VBH6 - 48MHz Cortex-M0 128KB MCU | STMicroelectronics
STM32F072VBH6

STM32F072VBH6 - 48MHz Cortex-M0 128KB MCU | STMicroelectronics

The STMicroelectronics STM32F072VBH6 is a 32-bit ARM Cortex-M0 RISC microcontroller operating up to 48 MHz, with 128 KB of Flash memory and a 100-UFBGA 7 x 7 mm package. It is designed for embedded USB, CAN, general-purpose control, and connected-device applications requiring a compact high-pin-count MCU. A microcontroller is a semiconductor device that integrates a processor core, program memory, data memory, peripherals, and communication interfaces into one package. The STM32F0 family belongs to the broader embedded microcontroller hierarchy and is positioned for cost-sensitive applications that need 32-bit processing without the complexity of higher-performance MCU families. The STM32F072VBH6 specifically combines 48 MHz processing, 128 KB Flash, USB, and CAN capabilities. Verified distributor data identifies the part as an ARM Cortex-M0 32-bit MCU with 128 KB Flash, USB, CAN, and a 100-UFBGA 7 x 7 mm package. Mouser describes it as a mainstream ARM Cortex-M0 USB-line MCU, while DigiKey lists the same 48 MHz operating frequency, 128 KB Flash organization, and 100-UFBGA package. The package supports dense PCB integration while exposing the device's broader peripheral and signal capabilities. The device family is appropriate for USB peripherals, CAN-connected equipment, industrial control modules, sensor interfaces, data acquisition systems, and consumer accessories. USB and CAN are especially relevant where a design needs short-range connectivity or robust network communication in an embedded controller. Firmware development should account for the exact STM32F072x8/xB device variant, pin multiplexing, clock configuration, and peripheral mapping before PCB release. The H6 ordering suffix identifies the supplied temperature and packaging configuration within STMicroelectronics' ordering system, but the supplied data does not state a complete temperature range, pinout, memory map, or electrical limits. Those parameters must be confirmed against the official STM32F072VB product page and manufacturer datasheet before design sign-off. For sourcing, compare the exact STM32F072VBH6 ordering code with STM32F072VBH6TR, which is identified in the verified distributor results as a distinct listing with the same 100-UFBGA 7 x 7 mm format. Package, temperature grade, firmware assumptions, and lifecycle requirements should be checked rather than assuming that a related ordering code is interchangeable. This page consolidates verified manufacturer and distributor information, preserves missing technical fields rather than guessing, and provides practical sourcing context for engineers evaluating the STM32F072VBH6.

見積もり 在庫あり