マイクロコントローラ

製品 (18172)

ATMEGA164PA-MCHR - 8-bit AVR MCU 16KB Flash 20MHz | Microchip
ATMEGA164PA-MCHR

ATMEGA164PA-MCHR - 8-bit AVR MCU 16KB Flash 20MHz | Microchip

The Microchip Technology ATMEGA164PA-MCHR is an 8-bit AVR RISC microcontroller with 16KB ISP flash memory, 20MHz maximum clock speed, and 44-pin VQFN (5x5 mm) package with exposed pad. The picoPower-qualified device also integrates 512B EEPROM, 1KB SRAM, 32 general purpose I/O lines, and operates over the industrial temperature range. An 8-bit AVR microcontroller is a Harvard-architecture RISC processor that executes most instructions in a single clock cycle, delivering throughput approaching 1 MIPS per megahertz. Within the power management and embedded control hierarchy, MCUs such as this sit at the node between raw logic devices and application processors, handling sensing, timing, and communication tasks in embedded systems. Key differentiating features include read-while-write flash for in-system programming, picoPower low-power technology for battery-operated designs, three flexible timer/counters with compare modes and PWM, and a real-time counter. Two USARTs enable multi-channel serial communication, while a byte-oriented Two-Wire serial interface (TWI/I2C) and SPI support peripheral expansion. Technical depth comes from the advanced AVR RISC architecture: 133 powerful instructions, most single-cycle, with 32 general purpose working registers directly connected to the ALU. This register-file-to-ALU connection eliminates the accumulator bottleneck of conventional 8-bit MCUs and allows system designers to optimize power consumption versus processing speed. Typical applications include industrial control nodes, consumer appliance controllers, sensor interface boards, and battery-powered metering products where the 10-bit ADC and picoPower sleep modes reduce system cost and energy use. A key design consideration: the 44-QFN package requires careful exposed-pad grounding for thermal and signal integrity, and the 20MHz maximum clock at 4.5-5.5V must be derated at lower supply voltages. This page synthesizes distributor pricing, drop-in alternatives within the ATmega family, and practical design notes not consolidated in the manufacturer datasheet.

USD $2.71 在庫あり
ATMEGA164PA-MN - 16KB Flash 20MHz AVR MCU | Microchip
ATMEGA164PA-MN

ATMEGA164PA-MN - 16KB Flash 20MHz AVR MCU | Microchip

The Microchip ATMEGA164PA-MN is a picoPower 8-bit AVR RISC microcontroller with 16 KB ISP flash memory, 512 B EEPROM, 1 KB SRAM and 20 MHz maximum clock frequency, housed in a 44-pad VQFN (7x7 mm, MN) package with exposed pad. An 8-bit AVR microcontroller is a Harvard-architecture RISC device in the broader microcontroller (MCU) hierarchy that integrates flash program memory, SRAM data memory, EEPROM, peripherals and a CPU core on one chip. The AVR ATmega family executes most instructions in a single clock cycle, giving roughly 1 MIPS per MHz of throughput, which places it among the most cycle-efficient 8-bit cores for embedded control, sensing and consumer hardware. Key features include 32 general purpose I/O lines, 32 general purpose working registers, a real-time counter, three flexible timer/counters with compare modes and PWM outputs, and picoPower low-power technology for battery-operated designs. The device supports 2.7V to 5.5V operation across the VQFN-44, making it usable directly on 3.3V and 5V rails without level shifting in many designs. Connectivity is rich for an 8-bit MCU: two USARTs, a byte-oriented two-wire serial interface (TWI, I2C-compatible) and an SPI serial port. An 8-channel 10-bit ADC provides analog acquisition for sensor front ends, while the read-while-write flash supports in-system self-programming for firmware updates and data logging. Typical applications include industrial sensor nodes and control panels, battery-powered metering and IoT endpoints, and consumer appliances requiring dual serial ports for, for example, a display and a radio module simultaneously. Design consideration: at 20 MHz and 5V the device draws its maximum dynamic current, so for battery designs prefer the internal 8 MHz RC oscillator plus picoPower sleep modes to cut active and standby current dramatically. This page synthesizes distributor pricing, drop-in alternatives, pinout data, and practical design notes not found in the manufacturer datasheet alone.

USD $2.15 在庫あり
ATMEGA164PA-MNR - 8-bit AVR MCU 16KB Flash 20MHz | Microchip
ATMEGA164PA-MNR

ATMEGA164PA-MNR - 8-bit AVR MCU 16KB Flash 20MHz | Microchip

The Microchip ATMEGA164PA-MNR is a picoPower 8-bit AVR enhanced RISC microcontroller with 16 KB ISP flash memory, 1 KB SRAM, 512 B EEPROM, and a 20 MHz maximum clock rate, housed in a 44-pin VQFN (7x7 mm) exposed-pad package delivered in tape and reel. By executing most instructions in a single clock cycle, this AVR ATmega device achieves throughput approaching 1 MIPS per MHz, letting designers trade clock speed directly against power consumption. An 8-bit AVR microcontroller is a Harvard-architecture MCU that separates program flash from data SRAM, sitting in the wider hierarchy of microcontrollers under the power-efficient embedded control IC category. The ATmega family is widely used where low standby power, deterministic execution, and mature tooling (AVR GCC, Atmel Studio / MPLAB X) matter more than raw processing throughput. Key features of the ATMEGA164PA-MNR include 32 general purpose I/O lines, three flexible timer/counters with compare modes and PWM, two USARTs, a byte-oriented Two-Wire (I2C-compatible) serial interface, an 8-channel 10-bit ADC, and a real-time counter with separate oscillator. The picoPower technology enables sub-uA sleep currents, and the device supports ISP and IAP flash programming with read-while-write capability. Operating voltage spans 2.5V/3.3V/5V systems per distributor parametric data, covering both 3.3V and 5V logic designs. Per Microchip application note AVR527, the ATmega164PA is a functionally identical drop-in replacement for the ATmega164P within the same 44-pin package, differing only in electrical characteristics due to a new manufacturing process - so existing firmware migrates without code changes. Typical applications include industrial sensor nodes, consumer appliances, battery-powered metering, HVAC control, and hobby/embedded products where a 5V-tolerant 8-bit MCU with on-chip ADC simplifies the BOM. When designing with this MCU, budget flash carefully: 16 KB holds structured C code well, but floating-point-heavy code or large lookup tables may force a move to the pin-compatible ATmega324PA/644PA/1284P. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

USD $2.66 在庫あり
ATMEGA164PA-MU - 8-bit AVR MCU 20MHz 16KB Flash | Microchip
ATMEGA164PA-MU

ATMEGA164PA-MU - 8-bit AVR MCU 20MHz 16KB Flash | Microchip

The Microchip Technology ATMEGA164PA-MU is a picoPower 8-bit AVR RISC microcontroller with 16 KB ISP flash memory, 512 B EEPROM, 1 KB SRAM, up to 20 MHz clock speed, and 32 general purpose I/O lines, housed in a 44-pin VQFN (7x7 mm) package. A microcontroller unit (MCU) is a single-chip computer that integrates a processor core, memory, and programmable peripherals into one IC, sitting at the heart of embedded systems. Within the MCU hierarchy, the ATmega family belongs to Microchip (formerly Atmel) AVR architecture, an 8-bit RISC line known for executing most instructions in a single clock cycle, delivering throughput close to 1 MIPS per MHz and letting designers balance power consumption against processing speed. Key features of the ATMEGA164PA include picoPower low-power technology for battery applications, read-while-write flash for safe in-system self-programming, and a rich peripheral set: three flexible timer/counters with compare modes and PWM, two USARTs, a byte-oriented Two-Wire Interface (TWI/I2C), and an 8-channel 10-bit ADC. The supply voltage spans 2.7 V to 5.5 V, supporting both 3.3 V and 5 V logic systems. Architecturally, the AVR core uses 32 general purpose working registers directly connected to the ALU, eliminating intermediate register access and enabling the 133-instruction set, most of which execute in one cycle. The advanced interrupt controller and nested structure support deterministic real-time behavior important for industrial control loops. Typical applications include industrial automation and sensor nodes, consumer appliances, battery-powered meters, and hobby/embedded designs requiring Arduino-compatible development. The two USARTs suit multi-channel communication; the 10-bit ADC fits analog sensor front ends. Design consideration: the 44-VQFN 7x7 mm package exposes a thermal pad on the underside for improved heat spreading and grounding; maximize via stitching under the pad and place 100 nF decoupling capacitors at each VCC pin within 2 mm. This page synthesizes distributor pricing, verified drop-in alternatives, and practical design notes not found in the manufacturer datasheet, with data verified as of 2026-09-16.

USD $2.55 在庫あり
ATMEGA164PA-MUR - 8-Bit AVR MCU 16KB Flash 20MHz | Microchip
ATMEGA164PA-MUR

ATMEGA164PA-MUR - 8-Bit AVR MCU 16KB Flash 20MHz | Microchip

The Microchip Technology ATMEGA164PA-MUR is a high-performance picoPower 8-bit AVR RISC microcontroller with 16 KB in-system programmable Flash, 1 KB SRAM, and 512 B EEPROM, operating at up to 20 MHz from a 1.8 V to 5.5 V supply in a 44-pin VQFN (7x7 mm) package. An 8-bit microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (Flash), data memory (SRAM), non-volatile data storage (EEPROM), and peripheral blocks such as timers, serial interfaces, and analog-to-digital converters. Within the semiconductor taxonomy, the ATmega164PA sits in the AVR ATmega family, which belongs to the 8-bit MCU class, itself a subset of embedded microcontrollers. These devices are the workhorses of embedded control, bridging the gap between simple logic and full 32-bit application processors. Key features include 16 KB of self-programmable Flash with read-while-write capability, 1 KB SRAM, 512 B EEPROM, 32 general-purpose I/O lines, 32 general-purpose working registers, a real-time counter, three flexible timer/counters with compare modes and PWM, two USARTs, a byte-oriented Two-Wire serial interface (TWI/I2C), an 8-channel 10-bit ADC, and an on-chip 2-cycle multiplier. The picoPower technology enables ultra-low-power operation, making the device suitable for battery-powered and energy-harvesting designs. The ATmega164PA is built on Microchip's proven AVR RISC architecture, executing 133 powerful instructions, most in a single clock cycle. This yields throughput approaching 20 MIPS at 20 MHz, balancing performance against power consumption. The device supports in-system programming and self-programming via a boot loader, simplifying field firmware updates. Typical applications include industrial control and automation, portable battery-powered instruments, consumer electronics, motor control, sensor hubs, and communication gateways. The dual USARTs and TWI interface make it well suited for multi-protocol bridging and human-machine interface panels. When designing with this device, pay close attention to decoupling, the reset circuit, and clock source selection. The 44-VQFN package requires careful PCB layout with a solid ground plane and adequate thermal vias under the exposed pad. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet, providing engineers with a single reference for selection and replacement decisions.

USD $2.89 在庫あり
ATMEGA164PV-10AQR - 8-bit AVR MCU 16KB 10MHz TQFP-44 | Microchip
ATMEGA164PV-10AQR

ATMEGA164PV-10AQR - 8-bit AVR MCU 16KB 10MHz TQFP-44 | Microchip

The Microchip Technology ATMEGA164PV-10AQR is a picoPower 8-bit AVR RISC microcontroller with 16 KB of In-System Programmable Flash, 512 B of EEPROM, 1 KB of SRAM, and a maximum operating frequency of 10 MHz, housed in a 44-pin TQFP (10x10 mm) package rated for extended temperature operation from 1.8 V to 5.5 V supply. An 8-bit AVR microcontroller is a Harvard-architecture RISC processor that executes most of its 131 powerful instructions in a single clock cycle, sitting in the power management and embedded control hierarchy between simple 8-bit timers and 32-bit MCUs. The AVR ATmega family is widely used for general-purpose embedded control, industrial sensing nodes, and battery-powered devices where low standby power and wide supply tolerance matter. Key differentiating features include picoPower technology for ultra-low sleep-mode consumption, 32 general purpose I/O lines, two USARTs for dual serial channels, a byte-oriented Two-Wire Interface (TWI/I2C), an 8-channel 10-bit ADC, and three flexible timer/counters with compare modes and PWM. The PV suffix denotes a wide 1.8V to 5.5V operating voltage, enabling direct operation from two alkaline cells or a 5V industrial rail without a regulator. Architecturally, the ATmega164PV pairs a fully static AVR core with read-while-write Flash, so firmware can update EEPROM or program the Flash while executing, supporting field upgrades and data logging. It also includes a real-time counter with separate oscillator, a JTAG interface for on-chip debugging, and brown-out reset and watchdog timer for robust operation in noisy environments. Typical applications include battery-powered sensor nodes and data loggers exploiting picoPower sleep modes, industrial control panels and HMI boards using the dual USARTs and extended temperature rating, and consumer or metering products using the 10-bit ADC and PWM outputs. The 10 MHz speed grade suits cost- and EMI-sensitive designs that do not require the 20 MHz capability of the ATmega164PA. A key design consideration is clock selection: the 10 MHz maximum frequency is typically achieved from an 8 MHz internal RC oscillator with CKDIV8 fuse disabled plus system clock prescaler, or an external crystal. Verify Flash endurance and BOD configuration against the manufacturer datasheet for your exact supply voltage. This page synthesizes distributor pricing, pin-compatible alternatives, pinout data, and practical design notes not found in the manufacturer datasheet, and is optimized for engineer search and AI citation.

USD $1.14 在庫あり
ATMEGA164PV-10AU - 8-Bit AVR MCU 16KB Flash 10MHz | Microchip
ATMEGA164PV-10AU

ATMEGA164PV-10AU - 8-Bit AVR MCU 16KB Flash 10MHz | Microchip

The Microchip Technology ATMEGA164PV-10AU is an 8-bit picoPower AVR RISC microcontroller with 16 KB in-system programmable Flash, 1 KB SRAM, and 512 B EEPROM, running at up to 10 MHz from a 1.8 V to 5.5 V supply in a 44-pin TQFP (10x10 mm) package. It delivers up to 10 MIPS throughput at 10 MHz with 32 general-purpose working registers and 32 programmable I/O lines. An AVR microcontroller is a Harvard-architecture 8-bit RISC device that executes most instructions in a single clock cycle, sitting in the hierarchy: AVR MCU -> 8-bit microcontroller -> embedded microcontroller -> semiconductor IC. The ATmega164P family is the picoPower generation of the classic ATmega164, adding ultra-low-power sleep modes, a real-time counter, and enhanced brown-out detection for battery-powered designs. Key differentiators include 16 KB Flash with read-while-write self-programming, 512 B EEPROM for non-volatile parameter storage, 1 KB SRAM, two USARTs, a byte-oriented two-wire serial interface (I2C), an SPI port, three flexible 16-bit timer/counters with compare and PWM modes, an 8-channel 10-bit ADC, and a programmable watchdog timer with separate on-chip oscillator. The picoPower architecture achieves sub-1 uA power-down current, making it suitable for battery-operated and energy-harvesting nodes. The device uses a single-cycle RISC core with 131 instructions and 32 x 8 general-purpose registers, enabling deterministic real-time response without the pipeline stalls typical of CISC architectures. On-chip debugWIRE and JTAG interfaces support in-circuit debugging and programming without external emulation hardware. Typical applications include industrial control panels, battery-powered sensor nodes, consumer appliance control boards, motor control front-ends, and legacy ATmega164 designs requiring a low-voltage 1.8 V operating option. The 44-pin TQFP footprint is shared across the ATmega164P/324P/644P family, allowing memory upgrades without PCB changes. When designing with this device, decouple every VCC/AVCC pin with a 100 nF ceramic capacitor placed within 5 mm of the pin, and keep the AREF pin bypassed with 100 nF to GND for ADC accuracy. The 10 MHz maximum frequency at 1.8 V requires the low-frequency crystal or internal calibrated RC oscillator option. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet, giving engineers a single reference for selection, replacement, and layout decisions.

USD $2.64 在庫あり
ATMEGA164PV-10MU - 8-Bit AVR MCU, 10MHz, 16KB Flash | Microchip
ATMEGA164PV-10MU

ATMEGA164PV-10MU - 8-Bit AVR MCU, 10MHz, 16KB Flash | Microchip

The Microchip Technology ATMEGA164PV-10MU is a picoPower 8-bit AVR RISC microcontroller delivering 16KB ISP flash, 1KB SRAM, and 512B EEPROM at up to 10MHz in a 44-pin VQFN (7x7 mm) package. An 8-bit AVR ATmega microcontroller is a self-contained processor core, memory, and peripheral system on a single chip, sitting within the wider hierarchy of microcontroller units (MCUs) -> embedded processors -> semiconductors. The AVR architecture uses a Harvard design with 32 general-purpose working registers directly connected to the ALU, allowing most of the 133 instructions to execute in a single clock cycle. Key features include the picoPower technology suite (idle, power-down, power-save, standby, and extended-standby sleep modes) for battery applications, read-while-write flash for safe self-programming, two USARTs for multi-channel serial communication, and an 8-channel 10-bit ADC. The wide 1.8V to 5.5V supply range directly enables coin-cell and single-cell Li-ion designs without a dedicated regulator. Technically, the device integrates three flexible timer/counters with compare modes and PWM, a byte-oriented two-wire interface (TWI/I2C), an SPI serial port, a real-time counter, programmable watchdog timer, on-chip debug via JTAG, and four power-saving sleep modes. In-system programmability over SPI allows firmware updates without removal from the PCB. Typical applications include battery-powered sensor nodes, industrial control panels, HVAC and metering systems, and embedded peripherals that need two independent UART links at very low sleep current. Design consideration: the 10MHz speed grade (V suffix) is rated across the full 1.8V to 5.5V range; if your design runs above 10MHz you must select the 20MHz A-variant instead. BOD (brown-out detection) configuration in the fuses strongly affects power-down current. This page synthesizes distributor pricing, verified drop-in alternatives, and practical design notes not consolidated in the manufacturer datasheet.

USD $1.58 在庫あり
ATMEGA164PV-10MUR - 8-bit AVR MCU 16KB Flash 10MHz | Microchip
ATMEGA164PV-10MUR

ATMEGA164PV-10MUR - 8-bit AVR MCU 16KB Flash 10MHz | Microchip

The Microchip Technology ATMEGA164PV-10MUR is a picoPower 8-bit AVR RISC microcontroller delivering 16KB ISP flash memory, 512B EEPROM, 1KB SRAM, and 10MHz maximum clock speed in a 44-pad VQFN (7x7 mm) package rated for industrial temperatures. It operates from a 2.7V to 5.5V supply and integrates 32 general-purpose I/O lines, two USARTs, an 8-channel 10-bit ADC, and three flexible timer/counters with compare modes and PWM. A microcontroller (MCU) is a complete computing system on a single chip, combining a processor core, program memory, data memory, and peripherals. The ATmega164PV belongs to the AVR family of 8-bit RISC microcontrollers, which sits within Microchip's broader portfolio of embedded processing ICs. AVR cores execute most instructions in a single clock cycle through their advanced RISC architecture, giving high code efficiency and deterministic real-time behavior that CISC architectures struggle to match. Key features include the picoPower technology suite for ultra-low sleep-mode consumption, read-while-write flash for safe in-application firmware updates, a byte-oriented Two-Wire Interface (TWI/I2C) for peripheral expansion, an SPI serial port, and a real-time counter with separate oscillator. The 133-instruction set, mostly single-cycle, plus 32 general-purpose working registers directly connected to the ALU, enable throughput approaching 1 MIPS per MHz. Architecturally, the ATmega164PV uses a Harvard structure with separate program and data buses. The 10-bit successive-approximation ADC supports up to 8 single-ended channels, while the JTAG interface provides on-chip debugging and boundary-scan capability. Brown-out detection and an internal RC oscillator reduce external component count. Typical applications include industrial sensor nodes, battery-powered meters, HVAC and building automation controllers, and consumer appliance control boards where 2.7V-5.5V wide-voltage operation and low standby power are essential. Design consideration: note that Microchip lists the pin-compatible ATMEGA164PA as the newer replacement device; new designs should evaluate the PA variant, which offers higher speed grades in the same 44-VQFN footprint while remaining firmware-compatible. This page synthesizes distributor pricing, drop-in alternatives, pin-level cross-references, and practical design notes not found in the manufacturer datasheet, as of 2026-09-16.

USD $1.30 在庫あり
ATMEGA164PV-10PQ - 8-bit AVR MCU 16KB 10MHz 40-PDIP | Microchip
ATMEGA164PV-10PQ

ATMEGA164PV-10PQ - 8-bit AVR MCU 16KB 10MHz 40-PDIP | Microchip

The Microchip Technology ATMEGA164PV-10PQ is a picoPower 8-bit AVR RISC microcontroller with 16KB ISP FLASH memory, 1KB SRAM, 512B EEPROM, and a 10 MHz maximum clock, packaged in a 40-pin PDIP (PQ) through-hole package. An 8-bit AVR ATmega microcontroller is a Harvard-architecture RISC processor in the broader hierarchy of microcontroller units (MCU) within embedded semiconductor devices. The AVR family executes most of its 131 instructions in a single clock cycle, and the ATmega164P generation adds picoPower technology, which cuts active and sleep-mode current for battery-operated designs. Microcontrollers of this class integrate program FLASH, SRAM, EEPROM, timers, serial interfaces, and an ADC on one chip, replacing multi-chip solutions. Key features include 16KB of in-system-programmable FLASH with read-while-write support, 32 general-purpose I/O lines, two USARTs, a byte-oriented Two-Wire Interface (TWI/I2C), an SPI port, and an 8-channel 10-bit ADC. The wide 1.8V to 5.5V supply range lets one design span low-voltage battery and 5V industrial environments. Technically, the advanced RISC core delivers up to 10 MIPS at 10 MHz with fully static operation. Three flexible timer/counters with compare modes and PWM, a real-time counter, and programmable brown-out detection complete the peripheral set. JTAG (on compatible packages) and ISP programming simplify development. Typical applications include industrial control panels, sensor data loggers, motor and lighting control, and educational or hobby embedded systems where the through-hole 40-PDIP package is preferred for prototyping and field replacement. Design consideration: keep the ADC reference clean by decoupling AVCC (pin 30) and AREF (pin 32) separately from the digital VCC rail; and note the 10 MHz speed grade, not 20 MHz, when porting code from faster ATmega164PA variants. This page synthesizes verified distributor data, family drop-in alternatives, and practical design notes not found in the manufacturer datasheet, giving engineers a single citable reference.

USD $2.85 在庫あり
ATMEGA164PV-10PU - 8-bit AVR MCU 16KB Flash 40-PDIP | Microchip
ATMEGA164PV-10PU

ATMEGA164PV-10PU - 8-bit AVR MCU 16KB Flash 40-PDIP | Microchip

The Microchip (Atmel) ATMEGA164PV-10PU is a high-performance picoPower 8-bit AVR RISC microcontroller with 16KB ISP FLASH (8K x 16), 512B EEPROM, 1KB SRAM, and 32 general-purpose I/O lines, rated for up to 10 MHz operation from 1.8V to 5.5V, housed in a 40-pin PDIP (40-PDIP) through-hole package. An 8-bit AVR microcontroller is a single-chip computer that integrates a RISC processor core, program FLASH, data SRAM, EEPROM, timers, serial peripherals, and analog-to-digital conversion on one die. Within the embedded systems hierarchy it belongs to the microcontroller -> embedded processor -> semiconductor taxonomy, sitting below 32-bit MCUs and above simple 8-bit controllers in capability. The AVR architecture executes most of its 133 instructions in a single clock cycle through its 32 general-purpose working registers, delivering up to 10 MIPS at 10 MHz. Key features include the picoPower technology for ultra-low sleep-mode consumption, 16KB of self-programmable ISP FLASH with read-while-write support, and a rich peripheral set: two USARTs, three flexible timer/counters with compare modes and PWM, a 10-bit ADC, byte-oriented Two-Wire Interface (I2C-compatible), SPI serial port, programmable watchdog timer, internal calibrated RC oscillator, and on-chip debug capability via JTAG. The wide 1.8V to 5.5V supply range and 'V' speed grade make it tolerant of battery voltage sag. Architecturally, the device uses an advanced Harvard-structure RISC core with single-cycle instruction execution, hardware multiplier support in the ATmega family, and in-system programming via SPI, enabling firmware updates on assembled boards without a socket. Typical applications include industrial control panels, battery-powered instruments, educational and hobby embedded platforms, and legacy AVR board maintenance where a through-hole 40-pin DIP footprint is required. When designing with this part, remember the 'PV' suffix denotes a 10 MHz maximum clock at the low-voltage grade; for new designs Microchip recommends the newer ATMEGA164PA family, which is parameter-similar and footprint-compatible. This page synthesizes distributor pricing, drop-in alternatives, pinout data, and practical design notes not found in the manufacturer datasheet.

USD $1.70 在庫あり
ATMEGA165-16AI - 8-bit AVR MCU 16KB Flash 16MHz 64-TQFP | Microchip
ATMEGA165-16AI

ATMEGA165-16AI - 8-bit AVR MCU 16KB Flash 16MHz 64-TQFP | Microchip

The Microchip Technology (Atmel) ATMEGA165-16AI is a low-power, 8-bit AVR enhanced RISC microcontroller with 16KB of in-system programmable (ISP) FLASH memory, up to 16 MIPS throughput at 16MHz, in a 64-pin TQFP (14x14 mm) package rated for the industrial temperature range (-40C to +85C). An 8-bit AVR microcontroller is a Harvard-architecture RISC processor that executes most instructions in a single clock cycle. Within the power management and embedded control hierarchy, the ATmega family sits in the general-purpose MCU class, bridging small 8-pin AVRs and larger 128KB devices. The ATmega165 is the non-LCD sibling of the ATmega169, sharing the same core, memory map and 64-pin TQFP footprint. Key features include 130 powerful instructions with mostly single-cycle execution, eight general-purpose 8-bit working registers, fully static operation, and up to 16 MIPS throughput at 16MHz. The part provides in-system programmable FLASH with optional boot-code section for in-application programming, plus JTAG boundary-scan and on-chip debugging support typical of the ATmega165/169 device family. Architecturally, the ATmega165 uses the AVR enhanced RISC pipeline with a single-level instruction fetch/decode stage, allowing one instruction per clock cycle for most opcodes. Program memory is organized as 8K x 16 bits, and the chip integrates SRAM, EEPROM, timers, USART serial port, SPI interface, an 8-channel 10-bit ADC, and multiple low-power sleep modes that make it well suited to battery-operated designs. Typical applications include industrial control panels, sensor front ends and data loggers, HVAC and building automation nodes, and legacy embedded systems that require a proven 8-bit platform with ISP field upgrades. The 64-pin TQFP gives generous I/O count for keypads, displays and peripheral expansion. When designing with the ATMEGA165-16AI, verify the supply voltage range against the specific datasheet table for this speed/temperature grade, decouple VCC and AVCC separately, and use the ISP interface (via the SPI pins) for production programming. Keep the JTAG pins in mind if boundary scan is required, as they double as general-purpose port pins after fuse programming. This page synthesizes distributor availability, drop-in alternatives, and practical design notes not found in the manufacturer datasheet, with pricing and stock references as of 2026-09-16.

USD $3.45 在庫あり
ATMEGA165A-AU - 8-Bit AVR MCU 16KB Flash 16MHz | Microchip
ATMEGA165A-AU

ATMEGA165A-AU - 8-Bit AVR MCU 16KB Flash 16MHz | Microchip

The Microchip Technology ATMEGA165A-AU is an 8-bit AVR RISC microcontroller with 16 KB in-system programmable Flash, 512 B EEPROM, 1 KB SRAM, and up to 16 MIPS throughput at 16 MHz, housed in a 64-pin TQFP (14x14 mm) package. It operates from 2.7 V to 5.5 V and provides 54 general-purpose I/O lines. An 8-bit microcontroller (MCU) is a single-chip computer that integrates a CPU, program memory, data memory, and peripherals such as timers, serial interfaces, and analog-to-digital converters. Within the product hierarchy, the ATMEGA165A-AU is an AVR-family MCU, which is a member of the 8-bit microcontroller class, itself part of the broader embedded processor and semiconductor market. The AVR architecture uses a modified Harvard layout with 32 general-purpose working registers and 133 powerful instructions, most executing in a single clock cycle. Key features include 16 KB of Flash with read-while-write capability, 512 B of byte-addressable EEPROM for non-volatile parameter storage, 1 KB of internal SRAM, a JTAG interface supporting boundary-scan and on-chip debug, and a 10-bit successive-approximation ADC. The device also integrates a programmable watchdog timer, brown-out detection, and multiple power-saving sleep modes that reduce current consumption for battery-powered designs. The ATMEGA165A-AU is fabricated using Atmel's high-density non-volatile memory process, combining Flash program storage with EEPROM data storage on a single die. Its fully static operation allows the clock to be halted without losing state, and the wide 2.7 V to 5.5 V supply range permits direct operation from 3.3 V or 5 V rails without external regulation. Typical applications include industrial control panels, battery management systems, portable instrumentation, home automation nodes, motor control, and legacy embedded designs migrating from older ATmega parts. The 64-pin TQFP footprint with 54 I/O lines suits designs requiring many digital interfaces plus analog sensing. When designing with this device, decouple every VCC pin with a 100 nF ceramic capacitor placed close to the pin, and provide a 10 uF bulk capacitor near the package. The JTAG interface shares pins with Port F, so plan the debug connector and application I/O allocation together. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet, giving engineers a single reference for selection, replacement, and layout decisions.

USD $3.47 在庫あり
ATMEGA165A-AUR - AVR 8-Bit MCU 16KB Flash 16MHz TQFP-64 | Microchip
ATMEGA165A-AUR

ATMEGA165A-AUR - AVR 8-Bit MCU 16KB Flash 16MHz TQFP-64 | Microchip

The Microchip Technology (Atmel) ATMEGA165A-AUR is a high-performance, low-power AVR 8-bit microcontroller IC featuring 16KB (8K x 16) of In-System Programmable Flash, 1KB SRAM, 512B EEPROM, and up to 16MHz clock speed, housed in a 64-pin TQFP (14x14 mm) surface-mount package supplied on tape and reel for industrial automated assembly. An 8-bit AVR microcontroller is a member of the broader microcontroller (MCU) product hierarchy: microcontroller -> embedded processor -> integrated circuit. The AVR core uses an advanced RISC architecture in which 133 powerful instructions are mostly executed in a single clock cycle, and eight general-purpose working registers are directly connected to the ALU. This Harvard-architecture design delivers throughput approaching 1 MIPS per MHz, allowing system designers to trade clock speed against power consumption. Key differentiating features of the ATMEGA165A-AUR include fully static operation, up to 16 MIPS throughput at 16MHz, a wide 2.7V to 5.5V supply voltage range, and 53 general-purpose I/O lines across multiple GPIO ports. On-chip peripherals include SPI, UART/USART, and USI serial interfaces for connectivity, along with in-system self-programmable Flash that enables field firmware updates without removing the device from the PCB. Technically, the ATmega165A belongs to the ATmega165A/325A/645A pin-compatible family, which shares the same 64-pin TQFP footprint and peripheral set while scaling Flash from 16KB to 64KB. This family scalability lets a single PCB layout migrate across memory tiers. The A-suffix generation is the second-generation refresh of the original ATmega165, improving analog and power characteristics while preserving code compatibility, and the -AUR ordering code denotes industrial temperature grade, tape-and-reel packing, and RoHS/green packaging. Typical applications include industrial control panels, sensor hubs and data loggers, building automation nodes, motor control front ends, and legacy AVR designs requiring a long-lifecycle drop-in family member. The 53 I/O lines and multiple serial interfaces make it well suited to designs that must drive displays, keypads, and communication links concurrently. A key design consideration is clock selection: the internal RC oscillator reduces BOM cost, but external crystal operation on the XTAL pins is recommended when UART communication demands precise baud-rate accuracy, particularly at 5V and elevated temperature. This page synthesizes verified distributor data, family drop-in alternatives, and practical design notes that go beyond what a single datasheet page provides.

見積もり 在庫あり
ATMEGA165A-MU - AVR 8-Bit MCU 16KB Flash 16MHz QFN-64 | Microchip
ATMEGA165A-MU

ATMEGA165A-MU - AVR 8-Bit MCU 16KB Flash 16MHz QFN-64 | Microchip

The Microchip Technology (Atmel) ATMEGA165A-MU is an 8-bit AVR ATmega microcontroller with 16 KB ISP Flash memory, 512 B EEPROM, 1 KB SRAM, and up to 54 general-purpose I/O lines, operating at up to 16 MHz from a 2.7 V to 5.5 V supply in a 64-pad QFN (9x9 mm, MLF) package. An 8-bit microcontroller is an integrated circuit that combines a processor core, memory, and peripherals on a single chip to execute a dedicated embedded control program. Within the power management hierarchy of embedded systems, the ATmega family sits in the 8-bit MCU category under microcontrollers under semiconductors, bridging small PIC-class devices and 32-bit ARM MCUs for cost-sensitive control tasks. Key features include the AVR Advanced RISC architecture executing 133 powerful instructions with mostly single-cycle execution, 32 general-purpose working registers, an on-chip JTAG interface for boundary scan and on-chip debugging, and read-while-write Flash for in-system self-programming. The device also integrates SPI and UART/USART serial connectivity plus a 10-bit ADC for analog sensing. Technically, the AVR core is a Harvard-architecture RISC machine with separate program and data buses, enabling one instruction per clock cycle for most operations. The 16 KB Flash supports 10,000 write cycles and code executes at 16 MIPS at 16 MHz, while the JTAG port enables production boundary-scan testing of assembled PCBs. Typical applications include industrial control panels, HVAC and building automation nodes, consumer appliance control, battery-powered instrumentation, and sensor-based embedded systems that need moderate Flash, rich GPIO, and 5 V tolerance. Design-wise, the 2.7 V to 5.5 V supply range permits direct 5 V industrial operation, but decouple the VCC/AVCC pins individually and remember the datasheet clock rating differences between the A (16 MHz) and V (8 MHz) speed grades. This page adds value beyond the datasheet by synthesizing distributor pricing, verified drop-in alternatives such as ATMEGA169P-16MCH and ATMEGA165P-16MU, and practical design notes for QFN-64 layouts.

USD $2.18 在庫あり
ATMEGA165A-MUR - 8-bit AVR MCU, 16KB Flash, 64-QFN | Microchip
ATMEGA165A-MUR

ATMEGA165A-MUR - 8-bit AVR MCU, 16KB Flash, 64-QFN | Microchip

The Microchip Technology ATMEGA165A-MUR is a high-performance, low-power 8-bit AVR RISC microcontroller with 16KB of ISP flash memory, 512B EEPROM, 1KB SRAM, and a maximum clock speed of 16MHz, housed in a 64-QFN (9x9 mm) surface-mount package with exposed pad. An 8-bit microcontroller is a complete computing system on a single chip that processes data in 8-bit words, integrating a CPU core, program memory (flash), data memory (SRAM and EEPROM), peripherals such as timers, UART, SPI, ADC, and general-purpose I/O. Within the power-management hierarchy of embedded systems, MCUs like the ATmega165A execute control firmware directly, sitting at the heart of the product rather than acting as a support IC. Key features include the advanced AVR RISC architecture with 133 powerful instructions, most executing in a single clock cycle, plus 32 general-purpose working registers directly connected to the ALU. The 16KB self-programmable flash supports read-while-write, 512B EEPROM retains calibration data through power cycles, and a JTAG interface enables on-chip debugging and boundary scan. The supply range of 1.8V to 5.5V covers both battery and industrial 5V rails. Architecturally, the AVR core achieves throughputs close to 1 MIPS per MHz, allowing the 16MHz ATMEGA165A to deliver up to 16 MIPS while remaining power efficient. The picoPower-style sleep modes and an integrated 10-bit ADC support low-duty-cycle designs. Typical applications include industrial control panels, consumer appliances, battery-powered instrumentation, LCD-driven user interfaces, and building automation nodes, where its rich I/O count (54 GPIO on the 64-pin package) and 10-bit ADC suit button matrices, sensor front ends, and display drive. Design-wise, keep decoupling capacitors close to VCC/AVCC pins and respect the ADC reference layout for analog accuracy. This page synthesizes distributor pricing, drop-in family alternatives, and practical design notes not found in the manufacturer datasheet, with pricing as of 2026-09-16.

USD $1.19 在庫あり
ATMEGA165P-16AN - AVR 8-bit MCU 16KB 16MHz TQFP-64 | Microchip
ATMEGA165P-16AN

ATMEGA165P-16AN - AVR 8-bit MCU 16KB 16MHz TQFP-64 | Microchip

The Microchip Technology ATMEGA165P-16AN is an 8-bit AVR RISC microcontroller with 16KB of In-System Programmable FLASH, 512B EEPROM, 1KB SRAM, and 53 general-purpose I/O lines, operating at up to 16 MHz in a 64-pin TQFP (14x14 mm) package. It runs from a 1.8V to 5.5V supply and delivers up to 16 MIPS throughput. An 8-bit microcontroller (MCU) is a single-chip computer that integrates a processor core, program memory, data memory, and peripherals such as timers, UARTs, and ADCs on one die. Within the power-management-free control-IC hierarchy, the ATmega AVR family sits in the general-purpose MCU class alongside PIC, 8051, and similar 8-bit architectures, serving as the central control element of embedded systems. Key features include the advanced AVR RISC architecture with 131 powerful instructions, most executing in a single clock cycle, 32 general-purpose working registers, and fully static operation to 16 MIPS. The picoPower-qualified P-variant adds improved power characteristics, and the JTAG interface (IEEE-compatible per the datasheet) provides boundary-scan, on-chip debugging, and in-system programming. Technically, the device pairs Read-While-Write FLASH with three flexible Timer/Counters, enabling motor control, PWM generation, and precise event timing. The Harvard architecture separates program and data buses, sustaining one-instruction-per-cycle throughput that outperforms classic 8051 cores at equal clock rates. Typical applications include industrial automation controllers, consumer appliance user interfaces, and battery-powered instrumentation, where 16KB of self-programmable FLASH and a rich peripheral set cover most mid-size control tasks without external memory. Design consideration: choose the 16AN grade for 16 MHz operation at 5V; for battery designs, evaluate the lower-speed PV voltage variants to exploit the wide 1.8V supply range. This page synthesizes distributor pricing, drop-in alternatives, comparison tables, and practical design notes not found in the manufacturer datasheet.

USD $1.65 在庫あり
ATMEGA165P-16ANR - 16KB Flash AVR MCU 16MHz 64-TQFP | Microchip
ATMEGA165P-16ANR

ATMEGA165P-16ANR - 16KB Flash AVR MCU 16MHz 64-TQFP | Microchip

The Microchip Technology ATMEGA165P-16ANR is a picoPower 8-bit AVR RISC microcontroller with 16 KB of In-System Programmable (ISP) Flash with read-while-write capability, 512 B EEPROM, 1 KB SRAM, and 53 general-purpose I/O lines, executing at up to 16 MHz (16 MIPS) and housed in a 64-pin TQFP (14x14 mm) surface-mount package. An 8-bit AVR microcontroller is a self-contained computing IC that integrates a RISC CPU core, nonvolatile program memory, RAM, peripherals, and I/O into a single chip, sitting at the top of the microcontroller hierarchy within the broader family of embedded processors and power-management silicon. The AVR architecture uses a Harvard memory structure with 131 single-cycle instructions, letting most instructions execute in one clock cycle. Key features include the advanced RISC AVR core with 32 general-purpose working registers, JTAG (IEEE 1149.1 compliant) boundary-scan and on-chip debugging, and picoPower technology that reduces active current consumption. The ATMEGA165P is the process-improved, lower-power successor to the original ATmega165, keeping full firmware and pinout compatibility. Technical depth: the device provides three flexible timer/counters with compare modes, an 8-channel 10-bit ADC, SPI and two USART serial interfaces, a byte-oriented two-wire interface, and an analog comparator. Programming is performed via SPI (ICSP) or JTAG, with true read-while-write self-programming for bootloaders. Operating voltage spans 2.7 V to 5.5 V, supporting both 3.3 V and 5 V systems. Typical applications include industrial control panels, consumer appliance controllers, instrumentation front ends, and battery-powered devices where the picoPower sleep modes extend battery life. Design consideration: at 16 MHz and 5 V, ensure a stable decoupled supply and route the ADC reference away from switching noise; the on-chip BOD should be enabled for flash integrity during brownouts. This page adds value beyond the datasheet by synthesizing distributor pricing, drop-in alternatives, and practical engineering notes in one place.

USD $2.18 在庫あり
ATMEGA165P-16AU - 8-bit AVR MCU 16MHz 16KB Flash | Microchip
ATMEGA165P-16AU

ATMEGA165P-16AU - 8-bit AVR MCU 16MHz 16KB Flash | Microchip

The Microchip Technology ATMEGA165P-16AU is an 8-bit AVR RISC microcontroller with 16 KB In-System Programmable Flash, 512 bytes EEPROM, 1 KB SRAM, and 53 general purpose I/O lines, housed in a 64-pin TQFP (14 x 14 mm) package and rated for 16 MHz operation at 2.7 V to 5.5 V supply. An 8-bit AVR microcontroller is a Harvard-architecture RISC processor that executes most instructions in a single clock cycle, sitting within the broader hierarchy of MCU -> microcontroller unit -> embedded processor -> semiconductor. The AVR ATmega family is widely used for cost-sensitive embedded control where flash memory must be reprogrammed in-system, and it remains popular in industrial control, instrumentation, and hobby/education platforms due to mature toolchain support (MPLAB X, AVR-GCC, ICSP programming). Key features of the ATMEGA165P-16AU include 133 powerful instructions with mostly single-cycle execution, 32 general purpose working registers, three flexible Timer/Counters, and a JTAG interface supporting boundary-scan, on-chip debugging, and programming. The picoPower-heritage design supports low-power idle and power-down modes, and the 16 MHz speed grade delivers roughly 16 MIPS of throughput. The wide 2.7 V to 5.5 V operating range lets one design span 3.3 V and 5 V systems. Technically, the device pairs fast-flash Read-While-Write capability with 512 bytes of non-volatile EEPROM for parameter storage. The SPI, USART, and TWI-style peripherals (per the manufacturer datasheet) enable straightforward connectivity to sensors, displays, and serial links, while the 10-bit ADC on the PF port handles analog acquisition. Typical applications include industrial control panels, LCD-based instruments, sensor hubs, battery-powered metering products, and in-circuit-programmable field devices. Design consideration: at 16 MHz and 5 V, ensure decoupling of 100 nF per VCC pin and observe JTAG pin sharing constraints (PF port) when boundary-scan is enabled. This page adds value beyond the manufacturer datasheet by synthesizing distributor pricing as of 2026-09-16, drop-in alternatives from the same ATmega family, and practical design notes in one place.

USD $5.10 在庫あり
ATMEGA165P-16MN - 8-Bit AVR MCU 16KB 16MHz 64-QFN | Microchip
ATMEGA165P-16MN

ATMEGA165P-16MN - 8-Bit AVR MCU 16KB 16MHz 64-QFN | Microchip

The Microchip Technology ATMEGA165P-16MN is a high-performance, low-power 8-bit AVR RISC microcontroller with 16KB of ISP Flash memory, 16MHz maximum clock frequency (16 MIPS throughput), and 53 general-purpose I/O lines, housed in a 64-pin QFN (9x9 mm) package with exposed pad. An 8-bit AVR microcontroller is a Harvard-architecture RISC processor that executes most instructions in a single clock cycle, positioning it within the broader hierarchy of microcontroller units (MCUs) under the semiconductor and embedded processing category. AVR MCUs from Microchip are widely used where cost-effective, deterministic 8-bit control is required, sitting alongside PIC and ARM Cortex-M families in the embedded systems ecosystem. Key features of the ATMEGA165P-16MN include 16KB (8K x 16) In-System Programmable Flash with read-while-write capability, 512B EEPROM, 1KB SRAM, and 32 general-purpose working registers. The advanced RISC architecture implements 131 powerful instructions, most executing in a single clock cycle, delivering up to 16 MIPS at 16MHz. The P-suffix denotes an enhanced process variant of the original ATmega165 with improved reliability and a wider industrial temperature range. Technical depth: the device integrates JTAG (IEEE 1149.1-compliant) boundary-scan and on-chip debugging, a programmable Watchdog Timer with separate on-chip oscillator, and multiple sleep modes including picoPower-class low-power modes that reduce consumption to microamp levels in power-down. Peripherals typically include an 8-channel 10-bit ADC, USART, SPI, and two 8-bit plus one 16-bit timer/counters with PWM outputs, enabling motor control, sensing, and communication tasks without external components. Typical applications include industrial automation and control panels, consumer appliances, battery-powered portable instruments, and building/HVAC control nodes, where the combination of 5V tolerance, self-programmable Flash, and rich peripheral set fits cost-sensitive embedded designs. A key design consideration is that the 64-QFN exposed-pad package requires a well-designed ground via array under the pad for thermal and electrical performance; designers migrating from TQFP footprints must verify land-pattern compatibility. This page synthesizes distributor pricing, drop-in alternatives within the AVR family, and practical design notes not found in the manufacturer datasheet.

USD $1.42 在庫あり
ATMEGA165P-16MNR - AVR 8-Bit MCU 16KB Flash 16MHz | Microchip
ATMEGA165P-16MNR

ATMEGA165P-16MNR - AVR 8-Bit MCU 16KB Flash 16MHz | Microchip

The Microchip Technology ATMEGA165P-16MNR is an 8-bit AVR RISC microcontroller with 16 KB In-System Programmable Flash, 512 B EEPROM, 1 KB SRAM, and up to 16 MIPS throughput at 16 MHz, housed in a 64-pad QFN (MLF) 9x9 mm package with exposed pad. It operates from 3.3V or 5V supplies and is rated to 105C in the MNR (industrial) grade. An AVR ATmega microcontroller is an 8-bit Harvard-architecture MCU that executes most of its 131 powerful instructions in a single clock cycle. Within the product hierarchy, the ATmega165P sits in the megaAVR family of general-purpose microcontrollers, below flash-rich parts such as the ATmega328P and above small-scale ATtiny devices, and serves as the programmable brain of embedded systems. Key features include the advanced RISC architecture with 32 general purpose working registers, fully static operation to 16 MIPS throughput, 16 KB of self-programmable Flash with Read-While-Write capability, 53 general purpose I/O lines, and a JTAG interface for boundary-scan, on-chip debugging, and programming. The picoPower-enhanced P-grade die also improves reliability relative to the original ATmega165. Architecturally, the three flexible Timer/Counters, the 10-bit ADC, USART, SPI, and Two-Wire Interface (TWI) peripherals make this part a compact single-chip solution for control and communication tasks. The JTAG port allows In-System Programming (ICSP) and on-chip debug using tools such as the MPLAB SNAP debugger. Typical applications include industrial control panels, sensor nodes and IoT endpoints, consumer appliance controllers, and battery-powered instrumentation where low-power AVR operation is valuable. A key design consideration is clock selection: the MNR is a blank, unprogrammed die relying on an external clock source or internal RC oscillator, so fuse configuration must match the crystal circuit to avoid bricking the device during development. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

USD $1.75 在庫あり
ATMEGA165P-16MU - 16MHz AVR MCU 16KB Flash 64-QFN | Microchip
ATMEGA165P-16MU

ATMEGA165P-16MU - 16MHz AVR MCU 16KB Flash 64-QFN | Microchip

The Microchip Technology ATMEGA165P-16MU is a low-power 8-bit AVR RISC microcontroller featuring 16KB of In-System Programmable Flash, 512B EEPROM, 1KB SRAM, and a maximum clock speed of 16MHz, housed in a 64-pin QFN (MLF) package measuring 9x9 mm with industrial temperature rating. An 8-bit AVR microcontroller is a single-chip processor built on the AVR enhanced RISC architecture, in which most of its 133 powerful instructions execute in a single clock cycle. Within the semiconductor hierarchy, it belongs to the microcontroller class (CPU plus Flash, EEPROM, SRAM, timers, and peripherals on one die) under the broader category of embedded processors and integrated circuits. The AVR family is widely used because it approaches 1 MIPS per MHz throughput, letting designers trade processing speed directly against power consumption. Key features of the ATMEGA165P-16MU include 53 general-purpose I/O lines, 32 general-purpose working registers, a JTAG interface supporting Boundary-scan, on-chip debugging, and in-system programming, and three flexible Timer/Counters with compare modes and PWM. The supply voltage range of 2.7V to 5.5V allows operation from both 3.3V and 5V rails, and the 'P' suffix denotes picoPower-class low-power operation with multiple sleep modes for battery-powered designs. Technically, the device combines an 8-bit AVR core with 16KB (8K x 16) self-programmable Flash featuring Read-While-Write capability, an on-chip ADC, SPI and USART serial interfaces, and an internal RC oscillator option. The JTAG port enables full boundary-scan testing of the assembled PCB as well as debugger attachment via tools such as AVR JTAGICE. Typical applications include industrial control panels, consumer appliances, HVAC and motor control boards, and embedded systems that need a compact 64-pad surface-mount MCU with rich I/O. The 9x9 mm QFN footprint suits dense, space-constrained boards. When designing, pay attention to the fine-pitch QFN land pattern: use the exposed die pad as ground with an array of thermal vias, and keep decoupling capacitors within 2 mm of supply pins. Verify programming-pin allocation (SPI or JTAG) before finalizing the layout. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet, giving engineers a single verified reference for ATMEGA165P-16MU selection and sourcing.

USD $2.19 在庫あり
ATMEGA165PA-AN - 8-Bit AVR MCU 16MHz 16KB Flash TQFP-64 | Microchip
ATMEGA165PA-AN

ATMEGA165PA-AN - 8-Bit AVR MCU 16MHz 16KB Flash TQFP-64 | Microchip

The Microchip Technology ATMEGA165PA-AN is a picoPower 8-bit AVR RISC microcontroller delivering 16 MIPS at 16 MHz, with 16 KB ISP flash, 512 B EEPROM, 1 KB SRAM, and 54 general-purpose I/O lines in a 64-pin TQFP (14x14 mm) package. A microcontroller integrates a processor core, program memory, data memory, and peripherals on a single chip, forming the lowest tier of the embedded system hierarchy: MCU -> embedded processor -> system-on-chip. The ATmega family from Atmel (now Microchip Technology) is one of the most widely deployed 8-bit AVR RISC MCU lines in industrial control, consumer, and hobbyist electronics, supported by the AVR GCC toolchain and Microchip Studio (formerly Atmel Studio). Key features include the picoPower technology for ultra-low power consumption (power-down mode draws only a few microamperes), an on-chip 8-channel 10-bit ADC, JTAG boundary-scan and on-chip debug, and read-while-write flash for self-programming. The AVR core executes most instructions in a single clock cycle, achieving up to 16 MIPS throughput at 16 MHz, and its 32 general-purpose working registers are directly connected to the ALU for efficient C-compiler code density. Peripheral set includes one USART, SPI serial interface, two-wire serial interface (TWI/I2C-compatible), a 16-bit timer/counter with PWM, and two 8-bit timer/counters. Operating voltage spans 1.8 V to 5.5 V, allowing single-cell battery or 5 V industrial logic operation, with -40C to +85C industrial temperature range for the -A grade. Typical applications include industrial sensor nodes, LCD-controlled consumer appliances (the ATmega169 sibling shares an integrated LCD controller heritage), motor control panels, battery-powered instrumentation, and general embedded control where flash in-system programmability simplifies field updates. When designing with this device, note that the 1 KB SRAM is the practical limit for complex middleware stacks; heavier networking or graphics workloads should migrate to the ATmega325 or ATmega645 family within the same TQFP-64 footprint. This page consolidates distributor pricing data, cross-reference information, and practical design notes not found in the manufacturer datasheet, verified as of 2026-09-16.

USD $2.19 在庫あり
ATMEGA165PA-AU - 8-bit AVR MCU 16MHz 16KB Flash | Microchip
ATMEGA165PA-AU

ATMEGA165PA-AU - 8-bit AVR MCU 16MHz 16KB Flash | Microchip

The Microchip Technology ATMEGA165PA-AU is an 8-bit AVR RISC microcontroller with 16KB of in-system programmable Flash, 512B EEPROM, 1KB SRAM, and a maximum clock speed of 16MHz, housed in a 64-pin TQFP (14x14 mm) surface-mount package. It operates from a 2.7V to 5.5V supply and provides 53 general-purpose I/O lines. A microcontroller (MCU) is a single integrated circuit that combines a processor core, memory, and programmable peripherals, serving as the embedded computing heart of a system. The AVR ATmega family sits within the broader hierarchy of 8-bit microcontrollers, which remain widely used for cost-sensitive, real-time control tasks where 32-bit processors are unnecessary overhead. The AVR architecture executes most of its 133 powerful instructions in a single clock cycle, with 32 general-purpose working registers directly connected to the ALU, delivering throughput up to ten times faster than conventional CISC microcontrollers at equivalent clock rates. Key features include the picoPower technology for ultra-low sleep-mode consumption, a JTAG interface for boundary-scan and on-chip debugging, three flexible 16/8-bit timers, a 10-bit ADC, SPI and USART serial interfaces, and read-while-write Flash for safe self-programming. The -AU suffix denotes the industrial-grade TQFP package with -40C to +85C operation. Technically, the picoPower P-variant of the ATmega165 family adds an enhanced sleep controller supporting idle, ADC noise reduction, power-save, power-down, standby, and extended standby modes, allowing battery-powered designs to spend most of their life in microamp-level sleep states while waking on pin-change, timer, or watchdog interrupts. Typical applications include industrial automation controllers, battery-powered metering and sensor nodes, consumer appliance control panels, and motor control systems where a rich peripheral set, 5V tolerance, and mature tooling matter more than raw processing power. A key design consideration is clock selection: 16MHz full-speed operation requires a 4.5V to 5.5V supply, while 8MHz operation is safe down to 2.7V, so battery designs must scale frequency with voltage per the AVR frequency-voltage curve. This page synthesizes distributor pricing context, verified drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

USD $2.05 在庫あり