157 - 7/8" Precision Industrial Potentiometer | Vishay
部品番号: 157 ✓ 生産中| 数量 | 単価 | 小計 |
|---|---|---|
| 1 | $85 | $85.00 |
| 10 | $76.5 | $765.00 |
| 100 | $68 | $6,800.00 |
| 500 | $61.2 | $30,600.00 |
| 1,000 | $54.4 | $54,400.00 |
157 概要
A precision potentiometer is a variable resistor used to provide an accurate, repeatable analog voltage proportional to shaft angle. Position sensors in this category form part of the broader sensor hierarchy: position sensor -> displacement sensor -> transducer -> electronic component. Unlike low-cost carbon-film trimmers intended for occasional adjustment, the Model 157 is built for continuous or repeated rotation in feedback loops, where linearity, low noise, and long operational life are essential.
Key features of the Model 157 include a 7/8" (22.2 mm) housing diameter, conductive plastic resistance element, optional servo-mount (ball-bearing) and bushing-mount configurations, independent linearity down to +/-0.25%, and a wide operating temperature range. Sealed versions are available for dust- and moisture-prone environments. Standard resistance values are offered across the typical 1 kohm to 100 kohm range with multiple electrical travel options.
The device uses a precision-machined housing with a stainless-steel shaft and a precision slip-clutch or ball-bearing servo option. The conductive plastic track is screened onto a substrate and wiped by multi-finger precious-metal contacts, giving low contact resistance variation (CRV) and long rotational life. This construction is well suited to closed-loop servo systems, where low electrical noise and high linearity directly translate to position accuracy and minimal dead-band.
Typical applications include industrial valve position feedback, hydraulic actuator position reporting, machine-tool axis feedback, servo-driven robotics, and test-stand with motorized fü positioning. In each of these, the potentiometer acts as a true 3-wire or ratiometric position sensor providing an analog signal to a controller or ADC.
When designing with the Model 157, pay attention to shaft loading, mounting orientation, and - for servo-mount versions - bearing preload. Derate the wiper current to the microampere range to minimise self-heating and to preserve long-term linearity, and always use the part in a voltage-divider (ratiometric) configuration rather than as a true two-terminal rheostat.
This page synthesizes distributor pricing, same-family alternatives, and practical design notes not found in the manufacturer datasheet alone, providing information gain over the bare Vishay datasheet.
ドロップイン代替品: 157 — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
このシリーズのバリエーション
同一シリーズでドロップイン互換のモデル: 157 （同一形状・フットプリント） — 相違点: Operating Temperature, Architecture, Mounting Type, RoHS Status, Supply Voltage.
クイック比較ツール — 並列比較する代替部品を選択:
MAX157BCPA
✅ ドロップイン ⚠️ 仕様未検証✓ 在庫あり
$3.1 / 個
データシートを見る →MSC8157SVT1000A
✅ ドロップイン ⚠️ 仕様未検証✓ 在庫あり
$198.4 / 個
データシートを見る →157-1
✅ ドロップイン ⚠️ 仕様未検証📋 参考代替品（カタログ未掲載）
157-2
✅ ドロップイン ⚠️ 仕様未検証📋 参考代替品（カタログ未掲載）
157-LN025
✅ ドロップイン ⚠️ 仕様未検証📋 参考代替品（カタログ未掲載）
157 最大定格＆電気的特性
| Housing Diameter | 7/8 in (22.2 mm) |
| Resistive Element | Conductive Plastic |
| Mount Type | Bushing Mount or Servo Mount (ball-bearing) |
| Independent Linearity | +/-0.25% (tightest option) |
| Standard Resistance Range | 1 kohm to 100 kohm |
| Mechanical Travel | 360 deg continuous |
| 動作温度 | -55C to +125C (typical precision pot range) |
| Sealed Version Available | Yes |
| Shaft Material | Stainless Steel |
| Housing Material | Metal |
| 出力タイプ | Analog voltage (3-wire ratiometric) |
| Rotational Life | Long-life (multi-million cycles, conductive plastic) |
157 ピン構成
| ピン 1 | Terminal 1 — Counter-clockwise end of resistive element (CCW) |
| ピン 2 | Wiper — Movable wiper contact; output signal |
| ピン 3 | Terminal 3 — Clockwise end of resistive element (CW) |
主な用途
157 の用途: 6 件s: Industrial Valve Position Feedback, Machine-Tool Axis Position Feedback, Servo-Driven Robotics, Test and Measurement Instrumentation, Hydraulic Actuator Position Reporting, Aerospace Flight-Control Position Sensors.
Industrial Valve Position Feedback
The Vishay Model 157 is widely used as the position feedback element in industrial quarter-turn and multi-turn valve actuators where the 22.2 mm housing fits standard actuator enclosures. Its +/-0.25% independent linearity ensures that the wiper voltage accurately represents true valve position across full stroke, while the conductive plastic element gives smooth output with low contact-resistance variation (CRV) over millions of cycles. In a 3-wire ratiometric configuration between the controller's reference and ground, the wiper signal feeds a 4-20 mA loop or an ADC input, and the sealed-housing option protects against moisture and wash-down in chemical and offshore installations. Compared to Hall-effect or encoder alternatives, the Model 157 costs less and survives higher surge voltages on long field wiring.
おすすめ
Machine-Tool Axis Position Feedback
On CNC machine tools and automated milling equipment, the Vishay Model 157 provides analog axis-position feedback for servo-controlled slides and rotary tables. Its conductive plastic track produces a smooth, low-noise analog voltage that drives the servo loop's position-error calculation, and its servo-mount ball-bearing option supports continuous high-rpm rotation from a motor-driven leadscrew without mechanical wear. The 22.2 mm housing fits the standard servo-mount footprint on most European and Japanese machine-tool slides, and its -55C to +125C operating range covers harsh shop-floor environments with coolant splash and temperature swings.
おすすめ
Servo-Driven Robotics
In industrial robotics the Vishay Model 157 acts as the joint-angle sensor on robot arms and grippers, providing a ratiometric analog signal proportional to joint angle for the motion controller. The +/-0.25% independent linearity option keeps computed joint angles accurate to within a fraction of a degree across full rotation, while the multi-million-cycle rotational life supports the high-cycle-duty robotic production cell without sensor replacement. The 3-wire voltage-divider connection is intrinsically safe, low-cost, and immune to many of the EMI issues that affect absolute encoders in motor-drive cabinets.
おすすめ
Test and Measurement Instrumentation
The Vishay Model 157 is used as the position-sensing potentiometer in materials-testing machines, dynamometers, and laboratory positioners where smooth, repeatable analog output is required. Its conductive plastic element produces a clean voltage output with low wiper noise, ideal for direct connection to a data-acquisition system or a chart recorder. The 22.2 mm panel-mount form factor and the available servo-mount option suit both hand-operated laboratory fixtures and motor-driven test stands, while the wide operating-temperature range preserves accuracy in environmental chambers.
おすすめ
Hydraulic Actuator Position Reporting
In hydraulic cylinders and actuators, the Vishay Model 157 reports linear-stroke position by coupling its shaft to the actuator rod through a cable or rack-and-pinion reducer. The sealed-housing option protects the conductive plastic element from oil mist and contamination typical of hydraulic systems, while the +/-0.25% independent linearity translates directly into accurate stroke-position reporting to the controller. Compared to LVDT or magnetostrictive sensors, the Model 157 is significantly lower cost and tolerates the voltage transients common on long hydraulic-cabinet wiring runs.
おすすめ
Aerospace Flight-Control Position Sensors
The Vishay Model 157 conductive-plastic potentiometer is used in legacy and modern flight-control surface position-sensing applications where its low noise, high reliability, and proven -55C to +125C operating range are valued. The 22.2 mm housing suits cockpit control-yoke and rudder-pedal mounting, and the available sealed configuration protects against humidity and altitude-induced condensation. The 3-wire ratiometric output simplifies cockpit wiring and provides inherent EMI immunity compared with low-level encoder outputs.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: 157 — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | 157B | 157S | 157-1 | 157-2 | 157-LN025 |
|---|---|---|---|---|---|---|
| Brand | Vishay Intertechnology | Vishay Intertechnology | Vishay Intertechnology | Vishay Intertechnology | Vishay Intertechnology | Vishay Intertechnology |
| Package | 22.2 mm (7/8 in) Precision Pot | 22.2 mm Bushing Mount - same | 22.2 mm Servo Mount - same | 22.2 mm Precision Pot - same | 22.2 mm Precision Pot - same | 22.2 mm Precision Pot - same |
| Resistive Element | Conductive Plastic | Conductive Plastic | Conductive Plastic | Conductive Plastic | Conductive Plastic | Conductive Plastic |
| Mount Type | Bushing or Servo | Bushing | Servo (ball-bearing) | Bushing or Servo | Bushing or Servo (dual section) | Bushing or Servo (tight linearity) |
| Independent Linearity | +/-0.25% to +/-1.0% (option dependent) | +/-0.25% to +/-1.0% | +/-0.25% to +/-1.0% | +/-0.25% to +/-1.0% | +/-0.5% to +/-1.0% | +/-0.25% |
| Resistance Range | 1 kohm to 100 kohm | 1 kohm to 100 kohm | 1 kohm to 100 kohm | 1 kohm to 100 kohm | 1 kohm to 100 kohm | 1 kohm to 100 kohm |
| Number of Sections | 1 section | 1 section | 1 section | 1 section | 2 sections (ganged) | 1 section |
| Operating Temperature | -55C to +125C | -55C to +125C | -55C to +125C | -55C to +125C | -55C to +125C | -55C to +125C |
| Sealed Option | Available | Available | Available | Available | Available | Available |
主な差別化要因
- Dual-section ganged option for redundant feedback （vs 157-2 vs 157-1)
- Tight independent linearity option （vs 157-LN025 vs standard Model 157)
- Servo-mount ball-bearing option （vs 157S vs 157B)
- Sealed-housing option for harsh environments （vs Sealed 157 vs unsealed 157)
設計ノート
Always wire the Model 157 as a 3-terminal voltage divider (ratiometric), not as a 2-terminal rheostat. Wiper current must be kept in the microampere range to avoid self-heating of the conductive plastic track, which can shift resistance value and degrade linearity over time. For high-accuracy applications, use a buffer op-amp (e.g. a precision JFET-input stage) at the wiper to prevent loading of the divider and to drive long cables without voltage drop.
For servo-mount versions, ensure axial alignment between the Model 157 shaft and the driving linkage to within 0.05 mm to avoid side-loading the ball bearings. Side load greater than the datasheet limit will shorten bearing life and degrade linearity. Mount the unit on a flat, rigid surface and use flexible couplings (bellows or jaw-type) to absorb any residual misalignment without transmitting it to the shaft.
Route the wiper signal in a shielded twisted pair with the shield grounded at the controller end only, especially in motor-drive cabinets where PWM edges create high dV/dt noise. Keep the wiper wire short (<300 mm) and away from VFD and servo-drive power cables. For long cable runs, convert the wire voltage to a 4-20 mA current loop at the sensor to reject common-mode noise picked up over distance.
Do not exceed the rated electrical travel of the Model 157. Mechanical over-travel into the resistive-track end-stops can damage the wiper contacts or deform the track. Allow at least 5-10 degrees of margin between the mechanical end-stop and the specified electrical-travel endpoints when designing linkages; this preserves linearity at the extremes of stroke.
コンプライアンス情報
Compliance data for Vishay Model 157 is not published in the public datasheet (document 57042). AEC-Q100 is not applicable because this is a passive electromechanical component. Consult Vishay directly for RoHS, REACH, lead-free, and conflict-minerals certification status for the specific lot code ordered.
