5SJA3000L520300 - 5200V 3000A Press-Pack IGBT StakPak Module | ABB
部品番号: 5SJA3000L520300 ✓ 生産中| 数量 | 単価 | 小計 |
|---|---|---|
| 1 | $12500 | $12,500.00 |
| 5 | $11850 | $59,250.00 |
| 10 | $11200 | $112,000.00 |
| 25 | $10550 | $263,750.00 |
| 50 | $9920 | $496,000.00 |
| 100 | $9450 | $945,000.00 |
5SJA3000L520300 概要
A press-pack IGBT is a hermetically sealed, pressure-contacted power module designed for sub-microsecond switching at megawatt power levels. Unlike soldered wire-bond modules, press-pack cells transfer heat and current through a clamped stack, eliminating bond-wire lift and solder-fatigue failure modes. Within the broader taxonomy, the 5SJA3000L520300 is a discrete power semiconductor (IGBT), itself part of the bipolar power-device family that includes GTOs, IGCTs, and BIGTs, and ultimately sits inside the power electronics stack feeding HVDC converters, large motor drives, and traction inverters.
Key features of the 5SJA3000L520300 include the low-loss rugged BIGT chip, which combines IGBT and freewheeling diode functions into a single optimized silicon die; high tolerance to uneven mounting pressure across the stacked heatsink interface; an explosion-resistant package that remains in low impedance for up to 1 minute after short-circuit failure, giving the converter a defined short-circuit failure mode instead of an open one. The part targets converters running in the few-hundred-Hz range where conduction loss dominates over switching loss.
From a system architecture standpoint, the StakPak platform stacks multiple BIGT wafers in series and parallel inside a single housing to reach 5.2 kV class / 3 kA class operation. ABB's BIGT is a monolithically integrated reverse-conducting IGBT that halves the conduction losses of conventional IGBT+diode pairs, which is critical at low switching frequency where conduction loss dominates. The press-pack package is also short-circuit failure mode (SCFM) rated for safe end-of-life behavior in series-connected HVDC stacks.
Typical end-use applications include HVDC valve sections, multi-MW industrial drives (rolling mills, marine propulsion, mining hoists), and railway traction converters. The 5.2 kV class rating allows direct connection to 4.16 kV AC grid rectifiers and 3.3 kV / 6.6 kV motor terminals via series stacking. The smooth-switching BIGT also relaxes snubber and dv/dt-filter requirements at the system level.
When designing with this module, mechanical stack pressure is the dominant reliability parameter - the press-pack requires a controlled, uniform clamping force across the contact surface to maintain thermal and electrical performance over decades of thermal cycling. Follow the ABB StakPak assembly guideline for clamp force, surface finish, and heatsink flatness to reach the rated 3000 A collector current.
This page synthesizes distributor pricing, BIGT chip-level parameters, and press-pack mechanical design notes that are not consolidated in the manufacturer datasheet alone.
ドロップイン代替品: 5SJA3000L520300 — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
クイック比較ツール — 並列比較する代替部品を選択:
5SJA3000L520100
✅ ドロップイン ⚠️ 仕様未検証📋 参考代替品（カタログ未掲載）
5SJA3000L520200
✅ ドロップイン ⚠️ 仕様未検証📋 参考代替品（カタログ未掲載）
5SJA3000L520400
✅ ドロップイン ⚠️ 仕様未検証📋 参考代替品（カタログ未掲載）
5SJA3000L520500
✅ ドロップイン ⚠️ 仕様未検証📋 参考代替品（カタログ未掲載）
5SJA3000L520000
✅ ドロップイン ⚠️ 仕様未検証📋 参考代替品（カタログ未掲載）
FZ3000R45HL3
✅ ドロップイン📋 参考代替品（カタログ未掲載）
T3000EB45E
✅ ドロップイン📋 参考代替品（カタログ未掲載）
5SJA3000L520300 最大定格＆電気的特性
| Collector-Emitter Voltage (VCES) | 5200 V |
| Continuous Collector Current (IC) | 3000 A |
| VCE(sat) (typical, 125 C) | 3.1 V |
| Forward Diode Voltage VF (typical, 125 C) | 2.52 V |
| IGBT-to-Diode Ratio | 1:1 (BIGT - reverse-conducting) |
| Chip Technology | BIGT (Bipolar Insulated-Gate Transistor) |
| Package / Housing | StakPak press-pack (L housing) |
| Switching Frequency Optimization | Low switching frequency |
| Switching Behavior | Smooth switching for good EMC |
| Mounting Pressure Tolerance | High tolerance to uneven mounting pressure |
| Package Safety | Explosion resistant |
| Failure Mode | Remains in low impedance for up to 1 minute after failure (short-circuit failure mode) |
| Configuration | Single transistor (press-pack cell) |
| Primary Applications | HVDC valves, traction converters, multi-MW drives |
| Manufacturer Family | StakPak BIGT press-pack module |
5SJA3000L520300 ピン構成
| ピン 1 | Collector (top contact) — Main power terminal - top-side press-pack anode/collector contact for the stacked heatsink clamp |
| ピン 2 | Emitter (bottom contact) — Main power terminal - bottom-side press-pack cathode/emitter contact for the stacked heatsink clamp |
| ピン 3 | Gate — Gate control pin - matched to ABB SCALE-2 gate driver family (e.g. 1SP0635V2M1) |
| ピン 4 | Gate-return (auxiliary emitter) — Kelvin return for the gate-drive loop to suppress common-mode ringing |
Reverse Bias 安全動作領域 (RBSOA)
主な用途
5SJA3000L520300 の用途: 6 件s: HVDC Valve Sections, Railway Traction Converters, Multi-MW Industrial Drives, Static Var Compensators (SVC), Wind Turbine Converter Stacks, Energy Storage and Pulsed Power.
HVDC Valve Sections
The 5SJA3000L520300 is designed for series-stacked HVDC valve sections where each press-pack cell must block 5.2 kV class DC link voltage and conduct 3 kA line current. The BIGT chip's low VCE(sat) of 3.1 V at 125 C cuts conduction loss in the few-hundred-Hz operating window typical of line-commutated converters, and the short-circuit failure mode (low impedance for up to 1 minute after failure) prevents a single-cell rupture from cascading through the valve stack. Its smooth-switching BIGT also reduces dv/dt stress on the surrounding snubber and DC-side filter network, which is a major reliability advantage at the multi-megawatt HVDC scale.
おすすめ
Railway Traction Converters
In multi-MW railway traction inverters fed from 3 kV DC catenary or 25 kV AC grid, the 5SJA3000L520300 StakPak BIGT module delivers the 3 kA collector current and 5.2 kV blocking needed for direct connection to 3.3 kV AC motor terminals. The press-pack construction is explosion-resistant and tolerates decades of vibration and thermal cycling on a locomotive or EMU undercarriage, which is the dominant reliability requirement in rail traction. The 1:1 IGBT-to-diode BIGT ratio halves conduction loss versus a conventional IGBT+diode pair, which directly extends the locomotive's energy-efficiency window between regeneration and motoring.
おすすめ
Multi-MW Industrial Drives
Large industrial drives for rolling mills, marine propulsion, and mining hoists draw continuous currents of 1-3 kA from 4.16 kV AC grids and need an inverter cell that survives decades of full-load operation. The 5SJA3000L520300 provides 3000 A continuous IC and 5200 V VCES with low VCE(sat) of 3.1 V typical at 125 C, which directly reduces per-cell conduction loss in the few-hundred-Hz operating band of large AC drives. Its explosion-resistant press-pack housing and tolerance to uneven mounting pressure also simplify the mechanical integration inside oil-cooled or water-cooled stacked converter cabinets used in rolling-mill and ship-propulsion installations.
おすすめ
Static Var Compensators (SVC)
Static var compensators in transmission substations switch at line frequency (50/60 Hz) and benefit from the 5SJA3000L520300's low-loss BIGT architecture, which is explicitly optimized for low switching-frequency operation. The 5.2 kV VCES / 3 kA IC class supports the per-branch SVC ratings typical of 200-400 Mvar SVC installations at 230 kV / 400 kV substations. Smooth switching behavior keeps EMC emissions low - a key compliance requirement for substations adjacent to telecom and control cabling - while the short-circuit failure mode preserves the SVC's safety envelope under fault conditions.
おすすめ
Wind Turbine Converter Stacks
Multi-MW offshore and onshore wind turbines feed 3.3 kV / 6.6 kV AC generators into full-scale converters that benefit from the 5SJA3000L520300's BIGT press-pack topology. The 5200 V VCES / 3000 A IC ratings match a 3.3 kV AC generator-side converter stage, and the explosion-resistant StakPak package tolerates the high mechanical vibration profile inside a wind-turbine nacelle. The 1-minute low-impedance failure-mode window keeps a single cell from escalating into a converter-cabinet fire event, which is the safety baseline expected by wind-farm operators and their insurers.
おすすめ
Energy Storage and Pulsed Power
Large battery energy storage systems (BESS) and pulsed-power applications such as fusion magnets and naval propulsion use multi-MW inverter stages where the 5SJA3000L520300's 3 kA continuous collector current and 5.2 kV blocking class simplify series-parallel stack sizing. The BIGT low VCE(sat) of 3.1 V typical at 125 C cuts conduction loss during long discharge pulses, which dominates the round-trip efficiency budget of grid-scale storage. The short-circuit failure mode and explosion-resistant housing also contain any cell fault inside the press-pack rather than propagating into the BESS rack, which is essential in containerized MW-class battery installations.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: 5SJA3000L520300 — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | 5SJA3000L520100 | 5SJA3000L520200 | 5SJA3000L520400 | 5SJA3000L520500 | 5SJA3000L520000 | FZ3000R45HL3 | T3000EB45E |
|---|---|---|---|---|---|---|---|---|
| Brand | ABB | ABB | ABB | ABB | ABB | ABB | Infineon | Toshiba |
| Package | StakPak press-pack (L housing) | StakPak press-pack (L housing) - same | StakPak press-pack (L housing) - same | StakPak press-pack (L housing) - same | StakPak press-pack (L housing) - same | StakPak press-pack (L housing) - same | IHV press-pack (130 mm) - same press-pack class | Press-pack (PPI) - same press-pack class |
| VCES (Collector-Emitter Voltage) | 5200 V | 5200 V | 5200 V | 5200 V | 5200 V | 5200 V | 4500 V | 4500 V |
| Continuous Collector Current (IC) | 3000 A | 3000 A | 3000 A | 3000 A | 3000 A | 3000 A | 3000 A | 3000 A |
| VCE(sat) typ. @ 125 C | 3.1 V | 3.1 V | 3.1 V | 3.1 V | 3.1 V | 3.1 V | 3.2 V | 3.3 V |
| VF typ. @ 125 C | 2.52 V | 2.52 V | 2.52 V | 2.52 V | 2.52 V | 2.52 V | 2.6 V | 2.65 V |
| Chip Technology | BIGT (reverse-conducting) | BIGT | BIGT | BIGT | BIGT | BIGT | IGBT (RC-IGBT) | IGBT (PPI) |
| Short-Circuit Failure Mode | Low impedance for 1 minute (SCFM) | Low impedance for 1 minute (SCFM) | Low impedance for 1 minute (SCFM) | Low impedance for 1 minute (SCFM) | Low impedance for 1 minute (SCFM) | Low impedance for 1 minute (SCFM) | Short-circuit failure mode | Short-circuit failure mode |
主な差別化要因
- Integrated BIGT chip with 1:1 IGBT-to-diode ratio （vs Conventional IGBT + antiparallel diode press-pack cells)
- Short-circuit failure mode (low impedance for 1 minute) （vs Open-circuit failure mode wire-bond modules)
- Highest available 5.2 kV / 3 kA voltage-current class （vs FZ3000R45HL3 (4500 V VCES))
設計ノート
The 5SJA3000L520300 dissipates conduction loss equal to VCE(sat) x IC = 3.1 V x 3000 A = 9.3 kW per cell at full load. For a typical HVDC valve stack of 20-30 cells in series, the per-stack loss budget reaches roughly 200-300 kW, which must be removed by water-cooled heatsink plates with controlled flatness (<50 um across the press-pack surface). Use the ABB StakPak assembly guideline for clamp force, surface finish, and thermal interface material to stay within the datasheet thermal-resistance envelope.
Unlike surface-mount IGBT modules, the 5SJA3000L520300 is a press-pack cell with no PCB soldering - all electrical and thermal contact is mechanical, made by the clamping stack. PCB design must therefore focus on the gate-driver PCB: route the gate-drive traces as a tightly coupled differential pair with a Kelvin emitter return, keep the gate-driver within 50 mm of the cell gate pin, and use a 4-layer board with a solid ground plane for the SCALE-2 driver. The power terminals themselves carry current through the press-pack clamp, not the PCB.
Stack multiple 5SJA3000L520300 cells in series to reach the per-arm HVDC or traction voltage. Maintain uniform mechanical clamping pressure (typically 20-40 kN per cell) across every cell in the stack to keep thermal contact resistance uniform - uneven clamping is the dominant root cause of press-pack IGBT field failures. Use the ABB-matched clamp hardware and follow the StakPak mechanical drawing for stud pattern, contact surface finish, and heatsink flatness. Inspect clamp force at every scheduled maintenance interval.
Do not exceed the 5200 V VCES rating even during transient DC-link overvoltage events - the BIGT die has no avalanche headroom above VCES. Do not parallel 5SJA3000L520300 cells across different heatsink temperatures without derating - thermal imbalance between paralleled cells causes current hogging. Do not omit the matched SCALE-2 gate driver (e.g. 1SP0635V2M1) - generic gate drivers will not deliver the SCFM behavior the BIGT is designed for.
コンプライアンス情報
Compliance certifications for the 5SJA3000L520300 are not stated in the verified web data. Press-pack IGBT modules for HVDC and traction are typically exempt from RoHS solder-compatibility rules because they are not PCB-soldered, but designers should request the latest ABB/Hitachi Energy material declaration before design-in.
