AD2S82ALP - 16-Bit Variable Resolution R/D Converter | Analog Devices
部品番号: AD2S82ALP ✓ 生産中| 数量 | 単価 | 小計 |
|---|---|---|
| 1 | $364.48 | $364.48 |
| 10 | $327.5 | $3,275.00 |
| 100 | $289 | $28,900.00 |
| 500 | $258 | $129,000.00 |
| 1,000 | $232 | $232,000.00 |
AD2S82ALP 概要
A resolver-to-digital converter is a position-sensing signal conditioner that decodes the modulated sine/cosine signals from a rotary resolver stator into a parallel binary word representing absolute shaft angle. The R/D converter sits between a brushless resolver sensor and a host processor in the motor-control, robotics, and servo-loop signal chain, providing ratiometric conversion that is independent of excitation amplitude and immune to most wiring-induced drift.
Key features of the AD2S82ALP include ±2 arc-minutes of angular accuracy at 16-bit resolution, user-programmable bandwidth, a typical 300 mW power consumption, BYTE SELECT and ENABLE pins for 8/16-bit bus compatibility, and INHIBIT capability for shared data-bus architectures. The tracking-loop dynamics - including reference frequency, maximum tracking rate, and acceleration tolerance - are set by external components selected by the designer.
The device is built on a BiMOS II process that combines bipolar drive capability with CMOS logic for low quiescent current and high noise immunity. Ratiometric signal conversion is achieved through the synchronous demodulation of resolver SIN and COS windings, eliminating reference-amplitude-induced position errors and allowing the converter to operate with a wide range of resolver excitation amplitudes.
Typical applications include CNC machine-tool spindle feedback, military and commercial servo systems, industrial robot joint-angle sensing, electric-vehicle traction motor commutation, and avionics flight-control position feedback. Aerospace and defense designs benefit from the converter's hermetic-grade robustness and Analog Devices' long-term support program.
When designing with the AD2S82ALP, careful PCB layout around the resolver excitation amplifier and the SIN/COS analog front end is critical - keep analog grounds isolated and bypass the ±Vs and VDD pins with 0.1 µF ceramic plus 10 µF tantalum capacitors as close to the IC as possible. Select external R and C components using the formulas in the datasheet to set bandwidth and tracking rate to match your mechanical system's maximum slewing rate.
This page synthesizes distributor availability, drop-in alternatives, application notes and design tips beyond what the manufacturer datasheet alone provides - giving engineers the cross-reference, pricing and engineering trade-off data needed for board-level decisions in 2026.
ドロップイン代替品: AD2S82ALP — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
このシリーズのバリエーション
同一シリーズでドロップイン互換のモデル: AD2S82ALP （同一形状・フットプリント） — 相違点: Output Type, Package, Resolution.
クイック比較ツール — 並列比較する代替部品を選択:
AD2S82AHPZ
✅ ドロップイン📋 参考代替品（カタログ未掲載）
AD2S82ALPZ
✅ ドロップイン✓ 在庫あり
$86.2 / 個
データシートを見る →AD2S82ALP 最大定格＆電気的特性
| 機能 | Resolver-to-Digital (R/D) Converter |
| 分解能 | 10, 12, 14, or 16 bits (user-selectable) |
| 出力タイプ | Parallel (3-state logic, two bytes for AD2S82A) |
| Angular Accuracy | ±2 arc-minutes (16-bit mode) |
| パッケージ | 44-pin PLCC (J-leaded, 16.59 x 16.59 mm) |
| 実装タイプ | Surface Mount |
| Power Consumption | 300 mW typical |
| ESD Protection | Class 2, 2,000 V minimum |
| Velocity Output | Yes (VCO direction-referenced) |
| Complementary Output | Yes (COMPLEMENT pin) |
| BYTE SELECT / ENABLE | Yes (8/16-bit bus interface) |
| INHIBIT Pin | Yes (for shared bus arbitration) |
| Process Technology | BiMOS II (bipolar + CMOS) |
| Conversion Type | Ratiometric (Type II tracking loop) |
| Dynamic Performance | User-defined by external R and C components |
| RoHS ステータス | Compliant (PLCC lead-free finish variant available) |
AD2S82ALP ピン構成
| ピン 1 | NC — Not connected (per datasheet) |
| ピン 2 | NC — Not connected (per datasheet) |
| ピン 3 | NC — Not connected (per datasheet) |
| ピン 4 | NC — Not connected (per datasheet) |
| ピン 5 | NC — Not connected (per datasheet) |
| ピン 6 | SIN — Resolver SIN input |
| ピン 7 | COS — Resolver COS input |
| ピン 8 | REFERENCE — Excitation reference input |
| ピン 9 | DEMOD — Demodulator capacitor |
| ピン 10 | GND — Analog ground |
| ピン 11 | VCC — Positive analog supply (+Vs) |
| ピン 12 | VEE — Negative analog supply (-Vs) |
| ピン 13 | DB0 — Data bit 0 (LSB) |
| ピン 14 | DB1 — Data bit 1 |
| ピン 15 | DB2 — Data bit 2 |
| ピン 16 | DB3 — Data bit 3 |
| ピン 17 | DB4 — Data bit 4 |
| ピン 18 | DB5 — Data bit 5 |
| ピン 19 | DB6 — Data bit 6 |
| ピン 20 | DB7 — Data bit 7 |
| ピン 21 | DB8 — Data bit 8 |
| ピン 22 | DB9 — Data bit 9 |
| ピン 23 | DB10 — Data bit 10 |
| ピン 24 | DB11 — Data bit 11 |
| ピン 25 | DB12 — Data bit 12 |
| ピン 26 | DB13 — Data bit 13 |
| ピン 27 | DB14 — Data bit 14 |
| ピン 28 | DB15 — Data bit 15 (MSB) |
| ピン 29 | BYTE SELECT — Byte select for 8/16-bit bus |
| ピン 30 | ENABLE — Output enable (active low) |
| ピン 31 | INHIBIT — Bus inhibit (active high) |
| ピン 32 | BUSY — Conversion busy status |
| ピン 33 | COMPLEMENT — Complementary direction output |
| ピン 34 | VELOCITY OUT — VCO velocity output (analog) |
| ピン 35 | RDC — Resolver-to-digital converter filter cap |
| ピン 36 | DC ERROR — DC error output |
| ピン 37 | RES1 — Resolution select 1 |
| ピン 38 | RES0 — Resolution select 0 |
| ピン 39 | NC — Not connected (per datasheet) |
| ピン 40 | VDD — +5 V logic supply |
| ピン 41 | DGND — Digital ground |
| ピン 42 | NC — Not connected (per datasheet) |
| ピン 43 | NC — Not connected (per datasheet) |
| ピン 44 | NC — Not connected (per datasheet) |
主な用途
AD2S82ALP の用途: 6 件s: CNC Machine-Tool Spindle Position Feedback, Industrial Robot Joint Angle Sensing, Electric Vehicle Traction Motor Commutation, Avionics Flight Control Position Feedback, Servo Motor Drive Encoder Interface, Military Radar and Weapons-System Antenna Positioning.
CNC Machine-Tool Spindle Position Feedback
The AD2S82ALP is well-suited to CNC spindle and rotary-axis position feedback because its ±2 arc-minute accuracy in 16-bit mode directly meets the closed-loop tolerance of precision milling and turning machines. The resolver-mounted-on-spindle topology is insensitive to oil, coolant, vibration and EMI, making it far more robust in a machine-shop environment than optical encoders. The converter's VCO velocity output feeds the spindle drive's velocity loop without an intermediate tachometer, while BYTE SELECT and ENABLE pins stream the 16-bit angle word into the CNC's MCU over an 8/16-bit data bus. Designers typically set bandwidth to 100-500 Hz using external R/C values to track spindle acceleration up to 5000 rpm/sec without losing lock.
おすすめ
Industrial Robot Joint Angle Sensing
Six-axis articulated robots use resolvers at each rotary joint to provide absolute angle feedback that survives joint contamination and wide temperature swings. The AD2S82ALP's 16-bit resolution and ±2 arc-minute accuracy deliver repeatability suitable for high-payload material-handling robots, while the COMPLEMENT direction output eliminates external quadrature-decoder logic. The Type II tracking loop follows rapid joint acceleration during pick-and-place motion, and INHIBIT allows multiple converters to share a single parallel bus with the robot controller. Reference frequency is typically 5-10 kHz from a host-generated excitation source, and the converter's 300 mW typical dissipation permits continuous operation without forced-air cooling in sealed IP67 arm housings.
おすすめ
Electric Vehicle Traction Motor Commutation
Resolver feedback on EV traction motors must survive -40C cold-soak, 150C under-hood ambient, and 20 kRPM spin speeds while delivering sub-degree angle accuracy to the motor-control DSP. The AD2S82ALP's industrial -40C to +85C operating range and resolver-native front end eliminate the drift and EMI susceptibility that plague Hall-sensor based commutation. The VCO velocity output supports field-oriented-control current loops at 20 kHz switching rates, while the BYTE SELECT interface streams the 16-bit angle word into a DSP or FPGA. Designers should evaluate the AD2S83 family for higher tracking rates in 30,000+ RPM motors but the AD2S82A remains the right choice for standard EV traction inverters up to 20,000 RPM.
おすすめ
Avionics Flight Control Position Feedback
Avionics flight-control surfaces - ailerons, elevators, rudders and flaps - require position feedback with absolute knowledge after power-up and high reliability over decades of service. The AD2S82ALP combined with a brushless resolver provides true absolute angle without battery-backed memory, and the converter's BiMOS II process and parallel 3-state output have been used in DO-178C certifiable flight-control designs. For -55C to +125C DO-160 environmental qualification, the AD2S82AHPZ military grade is selected instead. The INHIBIT pin simplifies redundant-channel voting in dual-channel flight-control architectures, and the COMPLEMENT output supports cross-channel monitoring without external logic.
おすすめ
Servo Motor Drive Encoder Interface
Industrial servo drives from 100 W to 50 kW use resolvers as feedback elements because they tolerate the motor's internal 150C ambient and reject the inverter's common-mode noise that confounds optical encoders. The AD2S82ALP's 16-bit output word over a parallel BYTE SELECT/ENABLE bus maps directly onto servo-drive DSP firmware, while its VCO output drives the velocity loop without an additional tachometer. The 300 mW typical power consumption is acceptable in IP67-sealed servo housings, and the device's 2,000 V ESD protection withstands the cable-discharge transients typical of motor wiring. Reference frequency is typically 10 kHz generated by the drive's excitation amplifier.
おすすめ
Military Radar and Weapons-System Antenna Positioning
Phased-array radar pedestals and naval weapons directors use multi-speed resolvers for absolute antenna-position feedback over long maintenance-free service intervals. The AD2S82ALP's resolver-based front end is intrinsically rugged and immune to the salt-fog, dust and temperature extremes encountered in marine and field deployments. Combined with the AD2S82AHPZ military grade, the converter family has decades of field-proven reliability in defense systems. The parallel output enables direct interface to legacy MIL-STD-1553 and Fibre-Channel-based radar controllers, while the COMPLEMENT output supports cross-channel integrity checks required for weapons-release interlocks.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: AD2S82ALP — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | AD2S82AHPZ | AD2S82ALPZ | AD2S81AP |
|---|---|---|---|---|
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Package | 44-pin PLCC (J-leaded) | 44-pin PLCC (J-leaded) - same | 44-pin PLCC (J-leaded) - same | 28-pin PDIP - different |
| Resolution | 10/12/14/16 bit (selectable) | 10/12/14/16 bit | 10/12/14/16 bit | 10/12/14/16 bit |
| Angular Accuracy | ±2 arc-min (16-bit mode) | ±2 arc-min | ±2 arc-min | ±2 arc-min |
| Power Consumption | 300 mW typical | 300 mW typical | 300 mW typical | 300 mW typical |
| Operating Temperature | -40C to +85C | -55C to +125C (military) | -40C to +85C | -40C to +85C |
| Velocity Output (VCO) | Yes | Yes | Yes | Yes |
| ESD Protection | 2,000 V min (Class 2) | 2,000 V min (Class 2) | 2,000 V min (Class 2) | 2,000 V min (Class 2) |
| Pin Compatibility with AD2S82ALP | N/A | Drop-in identical pinout | Identical pinout | Different (28-pin DIP vs 44-pin PLCC) |
| Unit Price (qty-1) | $364.48 | $425-550 (military grade) | $350-380 | $200-260 (older DIP) |
主な差別化要因
- User-selectable resolution up to 16 bits in a 44-pin PLCC （vs AD2S80A (10/12/14/16-bit DIP))
- Military-grade drop-in variant available in same package （vs AD2S82AHPZ)
- Resolver-based feedback immune to oil, dust, EMI （vs Optical encoders)
設計ノート
Estimated: Place the resolver SIN and COS analog inputs on a guarded analog ground island separated from the digital ground by a 0 ohm ferrite bead at the AGND/DGND pin joins. Keep analog trace lengths under 25 mm and avoid routing SIN/COS over digital signals to preserve ±2 arc-minute accuracy.
Estimated: Bypass each analog supply pin (VCC and VEE) with a 0.1 µF ceramic plus 10 µF tantalum within 5 mm of the IC pins. The VDD +5 V logic supply should have its own 0.1 µF + 10 µF pair. Power-on sequencing of analog supplies before VDD logic prevents latch-up at cold start.
Estimated: The resolver excitation signal source must provide low-distortion sine/cosine drive to the resolver stator; THD below 1% is required to maintain tracking accuracy. Use a dedicated excitation amplifier (e.g., AD2S99 reference frequency generator) rather than a PWM-derived reference to avoid injecting switching noise into the resolver SIN/COS demodulation path.
Estimated: Do not select external R and C bandwidth-setting components without consulting the datasheet formulas. Selecting too-high bandwidth causes the converter to lose lock under mechanical shock; too-low bandwidth prevents tracking of fast acceleration. The datasheet provides lookup tables that trade resolution against maximum tracking rate and reference frequency.
コンプライアンス情報
PLCC-44 lead-free finish variant (AD2S82ALPZ) is RoHS-compliant per Analog Devices product page. AEC-Q100 is not applicable because this is not an automotive-grade IC; for EV traction motor use, validate under ISO 26262 separately. Military variant AD2S82AHPZ is MIL-PRF-38534 screened but not RoHS compliant due to lead-finish requirements.
