AD606JNZ - 80dB 50MHz Logarithmic Amplifier | Analog Devices
部品番号: AD606JNZ ✓ 生産中AD606JNZ 概要
A logarithmic amplifier is a special-purpose analog IC that converts a signal’s amplitude into a voltage representing the logarithm of that amplitude. In the broader semiconductor hierarchy, it belongs to instrumentation amplifiers and linear amplifiers within the amplifier IC family. This compression characteristic allows an instrument to measure signals spanning a wide dynamic range while limiting the effect of large inputs.
The AD606 uses a nine-stage successive-detection technique to provide logarithmic and limited outputs. Its 80 dB dynamic range allows the output to represent amplitude over a substantial measurement span, while the 50 MHz bandwidth supports relatively fast signal changes. The built-in filter, signal-limiting function, and constant-amplitude limited output simplify the design of receiver, measurement, and control circuits.
The AD606JNZ operates from a single 5 V supply and produces a differential output for reduced sensitivity to noise and component tolerance differences when used with a differential receiver or ADC input stage. Its differential architecture is valuable in instrumentation because common-mode disturbances can be rejected when the output is sampled differentially. The circuit combines wide bandwidth with logarithmic detection in one analog package.
Typical applications include ultrasound and sonar signal processing, RF power measurement, communication receivers, spectrum analysis, and industrial monitoring systems. The 50 MHz bandwidth is especially relevant where the detected envelope changes quickly. In these systems, the logarithmic output can drive a comparator, display, or control loop while the limited output protects downstream circuitry from excessive signal amplitude.
Designers should account for the 16-pin PDIP footprint, bypass-capacitor placement, input dynamic range, and downstream receiver input range. The differential outputs should be routed as a matched pair to preserve noise rejection, and the gain-setting network should use the values shown in the manufacturer application schematics.
This product page combines the manufacturer’s device information with practical considerations for logarithmic signal processing, package reuse, comparison, and source selection. It identifies the functions engineers must verify when integrating the AD606JNZ into ultrasound, sonar, RF measurement, communication, and industrial monitoring equipment.
ドロップイン代替品: AD606JNZ — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
このシリーズのバリエーション
同一シリーズでドロップイン互換のモデル: AD606JNZ (同一形状・フットプリント) — 相違点: Supply Voltage.
AD606JN
✅ ドロップイン価格はお問い合わせください
データシートを見る →AD606JNZRL
✅ ドロップイン ⚠️ 仕様未検証📋 参考代替品(カタログ未掲載)
AD606JN-R7
✅ ドロップイン ⚠️ 仕様未検証📋 参考代替品(カタログ未掲載)
AD606JN
✅ ドロップイン ⚠️ 仕様未検証価格はお問い合わせください
データシートを見る →AD606JN
✅ ドロップイン価格はお問い合わせください
データシートを見る →AD606JNZ 最大定格&電気的特性
| Device Type | Monolithic logarithmic amplifier |
| Architecture | 9-stage successive-detection |
| Bandwidth | 50 MHz |
| Dynamic Range | 80 dB |
| Response Time | 5 µs |
| 電源電圧 | 5 V |
| 出力構成 | Differential logarithmic and limited outputs |
| Amplifier Circuit Count | 1 circuit |
| パッケージ | 16-pin PDIP |
| 動作温度範囲 | 0 °C to +70 °C |
| Maximum Power Dissipation | 600 mW |
| Built-in Features | Filter, signal limiting, and constant-amplitude output |
| Production Status | Production |
| Evaluation Board | AD606-EB |
| Primary Application | Ultrasound and sonar signal processing |
| 実装タイプ | Through-hole |
AD606JNZ 16-pin pdip ピン配置ガイド
AD606JNZ (16-pin pdip パッケージ) のピン配置。 このアナログコンポーネントは、入力、出力、および電源ピンを備えています。オフセットナル、補償、イネーブルピンの設定については、メーカーのデータシートを参照してください。信号調整やアンプ回路に最適です。
詳細なピン配置データはありません: AD606JNZ.
詳細は データシート をご参照ください。
主な用途
AD606JNZ の用途: 6 件s: Ultrasound Receiver Signal Processing, Sonar Envelope Detection, RF Power Measurement, Communication Receiver AGC, Spectrum Analyzer Signal Detection, Industrial Signal-Level Monitoring.
Ultrasound Receiver Signal Processing
The AD606JNZ fits ultrasound receiver channels that must detect echo amplitudes over a broad range without allowing a strong reflection to saturate the measurement chain. Its 80 dB logarithmic dynamic range compresses amplitude differences into a more manageable output, while the 50 MHz bandwidth and 5 µs response can follow fast echo-envelope variations. The differential logarithmic output should feed a differential receiver, ADC, or comparator to preserve common-mode rejection. Designers should use the manufacturer’s filter and gain network because external component values affect bandwidth and calibration behavior.
おすすめ
Sonar Envelope Detection
The AD606JNZ is suitable for sonar echo-envelope detection because logarithmic compression allows a wide range of returning-signal strengths to be represented without linear overload. Its 50 MHz bandwidth supports fast acoustic pulse transitions, and the 5 µs response reduces delay when the detected envelope is used for timing or threshold decisions. The limited output provides a constant-amplitude signal for downstream triggering, while the differential logarithmic output supports sensitive measurement. Board layout should preserve symmetric output routing and follow the manufacturer’s reference circuit for filtering and gain compensation.
おすすめ
RF Power Measurement
The AD606JNZ can serve as the logarithmic detector in RF power-measurement systems where signal strength may span many decibels. The 80 dB dynamic range covers a broad measurement span, while the 50 MHz bandwidth allows detection of fast-changing RF-derived envelopes. Because the device is specified in the customary dBm convention for sinusoidal inputs in a 50 Ω system, the external attenuator, detector input network, and calibration procedure are important to achieving meaningful absolute power readings. Use the differential output with matched downstream circuitry to improve rejection of common-mode noise.
おすすめ
Communication Receiver AGC
The AD606JNZ is appropriate for communication receivers that need signal-strength indication across a wide amplitude range. Its logarithmic output compresses strong and weak received signals into a more uniform monitoring range, while the limiter output can provide a constant-amplitude signal for thresholding or control. The 50 MHz bandwidth accommodates many modulated or carrier-related measurement paths, and the 5 µs response provides useful tracking speed. The 5 V supply and differential outputs simplify integration with modern receiver logic, while the limiting function protects downstream stages from excessive input amplitude.
おすすめ
Spectrum Analyzer Signal Detection
The AD606JNZ can support intermediate signal-detection stages in spectrum-analysis equipment. The 80 dB logarithmic range is useful when the analyzer must display or measure signals with widely different amplitudes, and the 50 MHz bandwidth provides a fast detector response for spectral sweep or modulation analysis. The 5 µs response limits delay in amplitude tracking, while the limiter output offers a stable trigger source. Differential routing to the analyzer’s ADC or comparator helps minimize common-mode pickup, and the external filter and gain values should match the manufacturer’s recommended circuit for the required bandwidth.
おすすめ
Industrial Signal-Level Monitoring
The AD606JNZ fits industrial monitoring systems that must measure variable-level analog signals without changing range whenever the signal crosses conventional amplifier thresholds. Its 80 dB dynamic range provides useful compression for vibration, acoustic, and sensor-derived levels, while the 50 MHz bandwidth and 5 µs response can accommodate rapidly changing transients. The limiter output can trigger alarms or threshold events, and the differential logarithmic output can drive telemetry or data acquisition hardware. Designers should account for the commercial 0 °C to +70 °C temperature range and use the AD606-EB platform to verify filtering, gain, and calibration before production deployment.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: AD606JNZ — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | AD606JN | AD606JNZRL | AD606JN-R7 | AD606J | AD606 |
|---|---|---|---|---|---|---|
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Package | 16-pin PDIP | 16-pin PDIP | 16-pin PDIP | 16-pin PDIP | 16-pin PDIP | 16-pin PDIP |
| Device Type | Monolithic logarithmic amplifier | Monolithic logarithmic amplifier | Monolithic logarithmic amplifier | Monolithic logarithmic amplifier | Monolithic logarithmic amplifier | Monolithic logarithmic amplifier |
| Bandwidth | 50 MHz | 50 MHz | 50 MHz | 50 MHz | 50 MHz | 50 MHz |
| Dynamic Range | 80 dB | 80 dB | 80 dB | 80 dB | 80 dB | 80 dB |
| Response Time | 5 µs | 5 µs | 5 µs | 5 µs | 5 µs | 5 µs |
| Supply Voltage | 5 V | 5 V | 5 V | 5 V | 5 V | 5 V |
| Output Configuration | Differential logarithmic and limited outputs | Differential logarithmic and limited outputs | Differential logarithmic and limited outputs | Differential logarithmic and limited outputs | Differential logarithmic and limited outputs | Differential logarithmic and limited outputs |
| Amplifier Circuit Count | 1 circuit | 1 circuit | 1 circuit | 1 circuit | 1 circuit | 1 circuit |
主な差別化要因
- Combines wide logarithmic range with high detector bandwidth (vs AD606JN)
- Provides logarithmic and constant-amplitude limited outputs (vs AD606JN-R7)
- Supports differential output routing (vs AD606J)
設計ノート
Use the manufacturer’s AD606 reference circuit as the basis for component placement and keep the differential output traces short and symmetric. Place input, output, and bypass capacitors close to their associated pins to limit parasitic feedback and preserve the intended detector bandwidth. Because the AD606 measures amplitude logarithmically, component tolerance and grounding errors can appear as calibration offsets; a grounded guard or reference plane around the sensitive input network may improve repeatability.
Route the two outputs as a differential pair into a receiver with matched input impedance. This preserves common-mode rejection and reduces susceptibility to noise coupled into only one output branch. Avoid adding capacitance, unequal trace lengths, or impedance discontinuities between the AD606 and the following ADC, comparator, or op-amp stage, particularly in a 50 MHz design where board parasitics can alter rise time and settling behavior.
Do not treat the logarithmic and limited outputs as interchangeable linear signals. The logarithmic output represents the compressed amplitude, while the limiter output maintains a constant-amplitude level for triggering or limiting functions. Confirm which output drives each receiver path, calibrate the logarithmic transfer curve over the intended input range, and observe the device’s 0 °C to +70 °C commercial temperature specification.
コンプライアンス情報
The AD606 family is identified as a production product, but RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations are not stated in the available manufacturer information.