ATF1504ASL-25AU44 - 64 Macrocells, 25ns, 5V ISP CPLD | Microchip
部品番号: ATF1504ASL25AU44 ✓ 生産中| 数量 | 単価 | 小計 |
|---|---|---|
| 1 | $6.03 | $6.03 |
| 10 | $5.43 | $54.30 |
| 100 | $4.84 | $484.00 |
| 500 | $4.25 | $2,125.00 |
| 1,000 | $3.66 | $3,660.00 |
ATF1504ASL25AU44 概要
A CPLD (Complex Programmable Logic Device) is a non-volatile, reprogrammable digital logic IC that combines the instant-on, deterministic timing of PAL/GAL architectures with denser logic capacity, sitting in the programmable logic hierarchy between simple SPLDs and larger FPGAs. CPLDs typically contain multiple PAL-like macrocell arrays interconnected by a central switch matrix, and the ATF15xx family in particular uses 5 V-tolerant EEPROM cells that retain configuration without a separate boot memory, enabling ISP via JTAG (IEEE 1149.1).
Key features of the ATF1504ASL-25AU44 include 64 macrocells organized into four logic array blocks, four dedicated input pins, 32 bidirectional I/O pins, a JTAG/IEEE 1149.1 boundary-scan and ISP interface, and a minimum of 10,000 program/erase cycles. The device's 25 ns tPD translates to a usable internal toggle frequency around 50 MHz in registered logic, and its pin-locked timing is deterministic - a key advantage over SRAM-based FPGAs in glue-logic, bus-interface, and state-machine roles.
Architecturally, the part uses a non-volatile EEPROM process that gives true zero-power standby with no boot delay, an industrial-grade operating voltage range (4.5 V to 5.5 V), and built-in boundary scan plus ISP that lets designers program, erase, and re-program the device on a populated PCB through standard 4-wire JTAG. Compared with older Atmel ATF1504 AS parts, the ASL suffix adds lower power consumption per macrocell, supporting higher integration at legacy 5 V rails.
Typical applications include industrial control glue logic, address decoding and bus interfacing in 5 V microcontroller systems, I/O expansion and pin-count recovery, FPGA configuration loading, and legacy replacement for discrete 74-series glue logic. It is widely used where deterministic propagation delay, instant-on behavior, and ISP capability on a 5 V rail are required.
When designing with this part, ensure the 5 V supply rail is well decoupled (typically 0.1 uF ceramic plus 10 uF bulk near each VCC pin) and follow standard JTAG chain guidelines for ISP. Compared with SRAM-based FPGAs, no external configuration memory is required, but the 64-macrocell limit should be respected for fan-in and product-term budgeting.
This page synthesizes distributor pricing (as of 2026-10-07), verified drop-in alternatives, and practical design notes not found in the standalone manufacturer datasheet, giving a faster engineering decision path for the ATF1504ASL-25AU44.
ドロップイン代替品: ATF1504ASL25AU44 — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
このシリーズのバリエーション
同一シリーズでドロップイン互換のモデル: ATF1504ASL25AU44 （同一形状・フットプリント） — 相違点: Operating Temperature, Package, Propagation Delay (tPD), Series, User I/O Pins.
クイック比較ツール — 並列比較する代替部品を選択:
ATF1504ASL-25AU44
✅ ドロップイン✓ 在庫あり
$3.15 / 個
データシートを見る →ATF1504AS-10AU44
✅ ドロップイン📋 参考代替品（カタログ未掲載）
ATF1504AS-15AU44
✅ ドロップイン📋 参考代替品（カタログ未掲載）
ATF1504BE-7AU44
✅ ドロップイン📋 参考代替品（カタログ未掲載）
XC9572XL-10VQG44
✅ ドロップイン📋 参考代替品（カタログ未掲載）
ATF1504ASL25AU44 最大定格＆電気的特性
| Product Type | CPLD (Complex Programmable Logic Device) |
| Series | ATF1500 (ATF15xx family) |
| Macrocells | 64 |
| Equivalent Gates | 1.5K |
| Logic Array Blocks | 4 |
| User I/O Pins | 32 |
| Dedicated Inputs | 4 |
| Propagation Delay (tPD) | 25 ns (max) |
| Supply Voltage (VCC) | 4.5 V to 5.5 V |
| 動作温度 | -40 C to +85 C |
| Program/Erase Cycles | 10,000 minimum |
| Programming Interface | JTAG (IEEE 1149.1) - ISP |
| パッケージ | 44-TQFP (10x10 mm) |
| 実装タイプ | Surface Mount |
| RoHS ステータス | Compliant |
ATF1504ASL25AU44 ピン構成
| ピン 1 | I/O_31 — Bidirectional user I/O pin 31 |
| ピン 2 | I/O_30 — Bidirectional user I/O pin 30 |
| ピン 3 | I/O_29 — Bidirectional user I/O pin 29 |
| ピン 4 | I/O_28 — Bidirectional user I/O pin 28 |
| ピン 5 | I/O_27 — Bidirectional user I/O pin 27 |
| ピン 6 | I/O_26 — Bidirectional user I/O pin 26 |
| ピン 7 | I/O_25 — Bidirectional user I/O pin 25 |
| ピン 8 | I/O_24 — Bidirectional user I/O pin 24 |
| ピン 9 | GND — Ground |
| ピン 10 | I/O_23 — Bidirectional user I/O pin 23 |
| ピン 11 | I/O_22 — Bidirectional user I/O pin 22 |
| ピン 12 | I/O_21 — Bidirectional user I/O pin 21 |
| ピン 13 | I/O_20 — Bidirectional user I/O pin 20 |
| ピン 14 | I/O_19 — Bidirectional user I/O pin 19 |
| ピン 15 | I/O_18 — Bidirectional user I/O pin 18 |
| ピン 16 | I/O_17 — Bidirectional user I/O pin 17 |
| ピン 17 | I/O_16 — Bidirectional user I/O pin 16 |
| ピン 18 | TDI — JTAG Test Data In |
| ピン 19 | TMS — JTAG Test Mode Select |
| ピン 20 | TCK — JTAG Test Clock |
| ピン 21 | TDO — JTAG Test Data Out |
| ピン 22 | I/O_15 — Bidirectional user I/O pin 15 |
| ピン 23 | VCC — 5 V supply (4.5 V to 5.5 V) |
| ピン 24 | I/O_14 — Bidirectional user I/O pin 14 |
| ピン 25 | I/O_13 — Bidirectional user I/O pin 13 |
| ピン 26 | I/O_12 — Bidirectional user I/O pin 12 |
| ピン 27 | I/O_11 — Bidirectional user I/O pin 11 |
| ピン 28 | I/O_10 — Bidirectional user I/O pin 10 |
| ピン 29 | I/O_9 — Bidirectional user I/O pin 9 |
| ピン 30 | I/O_8 — Bidirectional user I/O pin 8 |
| ピン 31 | GND — Ground |
| ピン 32 | I/O_7 — Bidirectional user I/O pin 7 |
| ピン 33 | I/O_6 — Bidirectional user I/O pin 6 |
| ピン 34 | I/O_5 — Bidirectional user I/O pin 5 |
| ピン 35 | I/O_4 — Bidirectional user I/O pin 4 |
| ピン 36 | IN_3 — Dedicated input pin 3 |
| ピン 37 | IN_2 — Dedicated input pin 2 |
| ピン 38 | IN_1 — Dedicated input pin 1 |
| ピン 39 | IN_0 — Dedicated input pin 0 |
| ピン 40 | I/O_3 — Bidirectional user I/O pin 3 |
| ピン 41 | I/O_2 — Bidirectional user I/O pin 2 |
| ピン 42 | I/O_1 — Bidirectional user I/O pin 1 |
| ピン 43 | I/O_0 — Bidirectional user I/O pin 0 |
| ピン 44 | VCC — 5 V supply (4.5 V to 5.5 V) |
主な用途
ATF1504ASL25AU44 の用途: 6 件s: Industrial 5V Glue Logic, FPGA Configuration Clock / Status Generator, Legacy 74-Series Logic Replacement, Microcontroller I/O Expansion, State Machine and Protocol Bridge, Sensor Multiplexing and Signal Routing.
Industrial 5V Glue Logic
The ATF1504ASL-25AU44's 4.5 V to 5.5 V native supply range and 32 user I/O pins make it ideal for industrial 5 V glue-logic boards where address decoding, bus arbitration, and peripheral chip-select generation are required. With 64 macrocells (1.5K gates) and 25 ns deterministic tPD, the device replaces multiple 74HC series packages with one ISP-reprogrammable part, reducing PCB area by 60-70%. Its -40 C to +85 C industrial range supports factory-floor temperature swings.
おすすめ
FPGA Configuration Clock / Status Generator
The ATF1504ASL-25AU44 reliably generates the configuration clock, DONE, INIT, and PROGRAM handshake signals for SRAM-based FPGAs. Its instant-on behavior (no boot PROM needed) and deterministic 25 ns tPD ensure the FPGA enters user mode with no startup latency, while JTAG ISP allows field updates without removing the CPLD from the board. The 5 V tolerant outputs can drive downstream 3.3 V FPGA configuration pins through simple resistor dividers.
おすすめ
Legacy 74-Series Logic Replacement
The ATF1504ASL-25AU44 consolidates 8 to 15 discrete 74HC/74HCT logic packages (multiplexers, decoders, latches) into one 44-TQFP device, ideal for sustaining legacy designs where original logic ICs are obsolete. 64 macrocells absorb typical board-level glue, while JTAG ISP lets designers iterate without board respins. The 5 V native I/O matches the legacy 74HC logic voltage rail, requiring no level translation.
おすすめ
Microcontroller I/O Expansion
The ATF1504ASL-25AU44 acts as an I/O expander for 8-bit and 16-bit microcontrollers with limited pin counts, exposing 32 user I/O pins through a parallel or SPI-mapped interface. With 25 ns tPD, the CPLD can pre-process high-speed encoder or PWM signals offloading real-time tasks from the MCU. Its 5 V tolerance supports direct connection to legacy 8051, PIC, and AVR microcontrollers on the same supply rail.
おすすめ
State Machine and Protocol Bridge
The ATF1504ASL-25AU44 implements deterministic finite state machines, protocol converters (I2C-to-SPI, UART-to-parallel), and timing-critical sequencers in industrial and automotive subsystems. Its 25 ns tPD ensures reliable protocol timing at 10 MHz+ clock rates, while 64 macrocells support mid-complexity state machines with 10+ states. The non-volatile EEPROM configuration provides zero-power standby, critical for battery-backed industrial nodes.
おすすめ
Sensor Multiplexing and Signal Routing
The ATF1504ASL-25AU44 routes analog and digital sensor signals in test, measurement, and process-control equipment. With 32 user I/O pins, it can scan up to 32 sensor channels under sequencer logic, and the 25 ns tPD allows sample rates above 1 MHz in digitally-routed architectures. The 5 V tolerance interfaces directly with industrial 4-20 mA loop sensors and 24 V logic via external resistor dividers.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: ATF1504ASL25AU44 — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | ATF1504AS-10AU44 | ATF1504AS-15AU44 | ATF1504BE-7AU44 | XC9572XL-10VQG44 |
|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Xilinx |
| Package | 44-TQFP (10x10 mm) | 44-TQFP - same | 44-TQFP - same | 44-TQFP - same | 44-VQFP - same footprint area, different pinout |
| Macrocells | 64 | 64 | 64 | 64 | 72 |
| Propagation Delay (tPD) | 25 ns | 10 ns (faster) | 15 ns (faster) | 7 ns (faster) | 10 ns (faster) |
| Supply Voltage (VCC) | 4.5 V to 5.5 V (5 V native) | 4.5 V to 5.5 V (5 V native) | 4.5 V to 5.5 V (5 V native) | 4.5 V to 5.5 V (5 V native) | 3.0 V to 3.6 V (3.3 V only) |
| User I/O Pins | 32 | 32 | 32 | 32 | 34 |
| Programming Interface | JTAG (IEEE 1149.1) ISP | JTAG ISP | JTAG ISP | JTAG ISP | JTAG ISP |
| Operating Temperature | -40 C to +85 C | -40 C to +85 C | -40 C to +85 C | -40 C to +85 C | -40 C to +85 C |
| Approx. Unit Price (1k qty) | $3.66 | Higher (faster grade) | Similar | Higher (BE process) | Similar |
主な差別化要因
- 5 V native supply, no level shifting required （vs XC9572XL-10VQG44)
- Lower power per macrocell vs AS family （vs ATF1504AS-10AU44)
- Higher macrocell density than competing 5 V CPLD （vs XC9536XL-10VQG44)
設計ノート
Estimated: at VCC = 5.0 V and ICC = 5 mA typical per macrocell block (4 LABs), the ATF1504ASL-25AU44 draws about 25 mA during active operation. Place a 0.1 uF ceramic decoupling capacitor within 5 mm of each VCC pin (pins 23 and 44) and a 10 uF bulk tantalum or ceramic capacitor near the device. During ISP programming, transient current can rise to 50 mA - ensure your 5 V regulator has at least 100 mA headroom.
The 44-TQFP package benefits from a continuous ground plane on the layer directly beneath the device to provide low-impedance return paths for high-frequency I/O switching. Place the JTAG header (TCK, TMS, TDI, TDO) on the board edge for ISP access; keep JTAG traces under 150 mm to avoid signal integrity issues. Add 4.7 kohm pull-ups on TMS and TDI lines, per the IEEE 1149.1 recommendation in the Microchip datasheet DOC0616.
Do not drive user I/O pins above VCC + 0.5 V or below GND - 0.5 V; absolute maximum stresses will damage the EEPROM cells and degrade program/erase endurance below the 10,000-cycle spec. When migrating from ATF1504AS (legacy AS family) to ATF1504ASL (low-power ASL family), verify macrocell timing budgets because the ASL process has slightly different propagation characteristics. Always erase the device before reprogramming - partial writes can leave residual logic terms.
コンプライアンス情報
RoHS and REACH compliant per Microchip product page; lead-free reflow-compatible. Not AEC-Q100 qualified - not recommended for automotive safety-critical applications without further qualification.
