ATMEGA103L-4AI - 8-Bit AVR MCU 128KB 4MHz TQFP-64 | Microchip
部品番号: ATMEGA103L-4AI ✗ 生産終了| 数量 | 単価 | 小計 |
|---|---|---|
| 1 | $18.5 | $18.50 |
| 10 | $16.65 | $166.50 |
| 100 | $14.8 | $1,480.00 |
| 500 | $12.95 | $6,475.00 |
| 1,000 | $11.1 | $11,100.00 |
ATMEGA103L-4AI 概要
An 8-bit AVR microcontroller is a single-chip processor built on the AVR enhanced RISC architecture, in which most of its powerful instructions execute in a single clock cycle. In the embedded-systems hierarchy it sits as the central processing element of a board, above discrete logic and below 32-bit application processors, and belongs to the broader family of microcontroller units (MCUs) that integrate program memory, data memory, timers, and communication peripherals on one die.
Key features of the ATMEGA103L-4AI include 121 powerful instructions with mostly single-clock-cycle execution, 128K bytes of in-system reprogrammable FLASH program memory, and serial programming interfaces. The L suffix denotes the low-voltage variant, while the AI suffix denotes the industrial temperature grade supplied in the 64-lead thin quad flat package (TQFP-64).
Architecturally, the device uses a Harvard-structure AVR core with separate program and data buses, allowing one instruction to be fetched while another is decoded and executed, which sustains throughput approaching 1 MIPS per MHz of clock. On-chip peripherals include an 8-channel 10-bit ADC, two 8-bit and two 16-bit timers with PWM, an SPI serial port, and a UART, providing complete system control in a single chip.
Typical applications include legacy industrial control boards, instrument front panels, building automation nodes, and communication equipment controllers. The low-voltage operation suits 3.3V systems, while the industrial temperature range supports factory-floor environments where consumer-grade parts cannot survive.
A key design consideration is that this part is mature/obsolete for new designs; engineers starting new boards should evaluate the pin-compatible ATmega128 family, which offers an ATmega103 compatibility mode and higher clock speeds. Verify FLASH endurance and programming-tool support before committing to new production.
This page synthesizes distributor availability data, drop-in alternative analysis, and practical design notes not found in the manufacturer datasheet, with pricing referenced as of 2026-09-15.
ドロップイン代替品: ATMEGA103L-4AI — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
このシリーズのバリエーション
同一シリーズでドロップイン互換のモデル: ATMEGA103L-4AI （同一形状・フットプリント） — 相違点: Operating Temperature, Maximum Clock Frequency, Package, SRAM, ADC.
クイック比較ツール — 並列比較する代替部品を選択:
ATMEGA103L-4AC
✅ ドロップイン✓ 在庫あり
$13.75 / 個
データシートを見る →ATMEGA103-4AI
✅ ドロップイン ⚠️ 仕様未検証📋 参考代替品（カタログ未掲載）
ATMEGA103-6AC
✅ ドロップイン✓ 在庫あり
$8.2 / 個
データシートを見る →ATMEGA128A-AU
✅ ドロップイン✓ 在庫あり
$4.3 / 個
データシートを見る →ATMEGA128-16AU
✅ ドロップイン✓ 在庫あり
$14.3 / 個
データシートを見る →ATMEGA103L-4AI 最大定格＆電気的特性
| Core Processor | AVR |
| Core Size | 8-Bit |
| 最大クロック周波数 | 4 MHz |
| Flash Program Memory | 128KB (64K x 16) |
| SRAM | 4KB |
| Instruction Set | 121 powerful instructions, mostly single-cycle |
| Architecture | AVR Enhanced RISC |
| Connectivity | SPI, UART |
| 動作温度 | -40C to +85C (industrial, AI suffix) |
| パッケージ | 64-TQFP (14x14 mm) |
| 実装タイプ | Surface Mount |
| Product Status | Obsolete |
| Packaging | Tray |
| RoHS ステータス | unknown |
ATMEGA103L-4AI 64-tqfp (14x14 mm) ピン配置ガイド
ATMEGA103L-4AI (64-tqfp (14x14 mm) パッケージ) のピン配置。 このデジタルICには、GPIO、通信インターフェース (UART、SPI、I2C)、および電源ピンが含まれています。代替ピン機能と設定オプションについては、メーカーのデータシートを参照してください。組み込みシステム設計とPCBレイアウトに不可欠です。
詳細なピン配置データはありません: ATMEGA103L-4AI.
詳細は データシート をご参照ください。
主な用途
ATMEGA103L-4AI の用途: 6 件s: Legacy Industrial Control Boards, Instrument Front Panels and HMI, Building Automation Nodes, Communication Equipment Controllers, Automotive Off-Highway and Specialty Retrofits, Security and Access Control Panels.
Legacy Industrial Control Boards
The ATMEGA103L-4AI is a natural fit for existing industrial controller boards originally designed around the ATmega103 family. Its 128KB of in-system programmable FLASH accommodates substantial control firmware, while 4KB of SRAM handles real-time variables and communication buffers. The AI industrial temperature grade of -40C to +85C survives factory-floor environments that would defeat consumer-grade parts. In these systems the MCU typically manages SPI-connected peripherals and a UART link to a supervisory PLC or SCADA node. Because the part is obsolete, service and repair builds should be paired with a lifetime-buy or qualified with the pin-compatible ATmega128 to de-risk future maintenance.
おすすめ
Instrument Front Panels and HMI
Test and measurement instruments, laboratory power supplies, and industrial HMIs historically used the ATmega103L for front-panel control: scanning keys, driving segmented LCDs or LED clusters via its I/O ports and PWM-capable timers, and reporting status over UART to the main measurement engine. The 4 MHz clock is sufficient for scan rates and debounce logic, and the 128KB FLASH leaves generous room for menu structures and localization tables. Its 64-TQFP (14x14 mm) package offers enough I/O count for direct key-matrix and display wiring without port expanders, keeping board cost low in repair and sustaining-engineering scenarios.
おすすめ
Building Automation Nodes
Dampers, valve actuators, and zone controllers in HVAC building automation were commonly built on AVR MCUs like the ATmega103L-4AI. The integrated UART links the node to RS-485 gateways through external transceivers, SPI interfaces to real-time clocks and ADC front ends, and timer PWM outputs drive actuator motors. The low-voltage L variant suits 3.3V logic rails shared with sensors, while the industrial temperature range covers rooftop and mechanical-room installations. Designers maintaining these nodes should note the 4 MHz ceiling constrains protocol stacks; the 16 MHz ATMEGA128A-AU is a same-footprint upgrade path with an ATmega103 compatibility fuse that minimizes firmware changes.
おすすめ
Communication Equipment Controllers
The ATMEGA103L-4AI serves well as a housekeeping controller in telecom and networking equipment: supervising power supplies, reading temperature and fan-speed sensors over SPI, sequencing rails, and asserting alarms over UART to a management card. The 121-instruction AVR RISC core with mostly single-cycle execution delivers deterministic interrupt latency, important for watchdog and fault-handling routines, and the large 128KB FLASH supports logging and multi-protocol firmware. The 64-TQFP footprint simplifies replacement during board repair, and the ATmega128A drop-in path allows the same PCB land pattern to be preserved through future production life-extension builds.
おすすめ
Automotive Off-Highway and Specialty Retrofits
Non-passenger-vehicle equipment such as agricultural controllers, marine gauges, and specialty-vehicle retrofits adopted the ATmega103L for engine-adjacent monitoring tasks where its industrial -40C to +85C rating and robust FLASH endurance proved reliable. Typical circuits use the 10-bit ADC-era peripherals available on this family generation plus UART links to instrument clusters. These designs are frequently frozen for regulatory or homologation reasons, making an exact-form-factor replacement critical. Where the L-variant low-voltage rail matches the vehicle 5V sensor domain, the ATMEGA128A-AU operated in ATmega103 compatibility mode preserves firmware investment while restoring an active supply chain.
おすすめ
Security and Access Control Panels
Access-control panels, alarm communicators, and keypad controllers benefit from the ATMEGA103L-4AI's combination of generous 128KB program memory for event logs and menus, SPI connectivity to memory and RFID front ends, and UART signaling to dialers or network modules. Deterministic single-cycle instruction execution supports tight timing for buzzer tones, LED indication, and tamper-switch polling. Its 64-pin TQFP package provides sufficient I/O for relay drivers and zone inputs without external expansion. Because the device is obsolete, new security-product revisions should migrate to the ATmega128A on the identical footprint, reusing the existing layout with only BOM and fuse-bit changes.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: ATMEGA103L-4AI — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | ATMEGA103L-4AC | ATMEGA103-4AI | ATMEGA103-6AC | ATMEGA128A-AU | ATMEGA128-16AU |
|---|---|---|---|---|---|---|
| Package | 64-TQFP (14x14 mm) | 64-TQFP (14x14 mm) - same | 64-TQFP (14x14 mm) - same | 64-TQFP (14x14 mm) - same | 64-TQFP - same footprint | 64-TQFP - same footprint |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Max Clock Frequency | 4 MHz | 4 MHz | 4 MHz | 6 MHz | 16 MHz | 16 MHz |
| Flash Memory | 128KB (64K x 16) | 128KB | 128KB | 128KB | 128KB | 128KB |
| SRAM | 4KB | 4KB | 4KB | 4KB | 4KB | 4KB |
| Temperature Grade | Industrial (-40C to +85C) | Commercial | Industrial | Commercial | Industrial (-40C to +85C) | Industrial (-40C to +85C) |
| Lifecycle Status | Obsolete | Obsolete | Obsolete | Obsolete | Active | Active |
| ATmega103 Compatibility Mode | Native (is ATmega103) | Native | Native | Native | Yes (M103C fuse) | Yes (M103C fuse) |
| Voltage Variant | L (low-voltage variant) | L variant | Standard 5V | Standard 5V | Standard 5V | Standard 5V |
主な差別化要因
- Native ATmega103 silicon with low-voltage operation （vs ATMEGA128A-AU)
- Industrial temperature rating （vs ATMEGA103L-4AC)
- Guaranteed legacy compatibility versus higher speed （vs ATMEGA128-16AU)
設計ノート
The ATMEGA103L-4AI is classified obsolete in distributor databases, so any new purchase is residual stock with uncertain date codes. For new board revisions, design in the ATMEGA128A-AU on the same 64-TQFP footprint and enable its ATmega103 compatibility mode (M103C fuse) so legacy firmware runs without modification. Verify peripheral register maps and fuse settings against the ATmega128 datasheet, and confirm low-voltage rail compatibility since the ATmega128A is 5V-oriented.
The L suffix marks the low-voltage variant of the ATmega103 family, intended for reduced supply rails relative to the standard 5V part. When mixing this MCU with 5V peripherals on the SPI or UART bus, check the datasheet absolute maximum ratings and logic-level thresholds for the specific L operating range before wiring direct connections; level shifting may be required depending on your chosen rail. Decouple VCC pins with 0.1 uF ceramics placed close to each supply pin.
At the 4 MHz maximum clock the ATmega103L is undemanding for signal integrity, but the SPI bus and UART lines still benefit from short traces, series termination near the driver, and a solid ground reference. Keep crystal or oscillator traces as short as possible and guard them with ground pours to avoid startup problems. For in-system programming, preserve the dedicated programming pin (PEN) access on the PCB per the ATmega103/L datasheet programming section.
コンプライアンス情報
Compliance data not present in the provided distributor snippets; original Atmel-era production predates universal RoHS compliance, so status depends on lot date code. Request material declarations from the supplier.