ATSAMD20J14A-CUT - SAM D20 32-bit ARM Cortex-M0+ MCU, 16KB Flash | Microchip
部品番号: ATSAMD20J14A-CUT ✓ 生産中| 数量 | 単価 | 小計 |
|---|---|---|
| 1 | $1.46 | $1.46 |
| 10 | $1.31 | $13.10 |
| 100 | $1.17 | $117.00 |
| 500 | $1.05 | $525.00 |
| 1,000 | $0.94 | $940.00 |
ATSAMD20J14A-CUT 概要
An ARM Cortex-M0+ microcontroller is the smallest, most energy-efficient member of the ARM Cortex-M family, combining a Thumb-2 instruction set with a single-cycle multiplier and NVIC interrupt controller. The ATSAMD20J14A sits inside the broader microcontrollers (MCU) product category, which falls under integrated circuits (ICs) and ultimately semiconductors in the taxonomy hierarchy. Cortex-M0+ cores are widely chosen for battery-powered and cost-sensitive applications because they deliver 32-bit performance at power levels comparable to 8-bit MCUs.
Key features include the Cortex-M0+ core with single-cycle hardware multiply, 16 KB self-programmable Flash, 2 KB SRAM, and the Microchip Event System for inter-peripheral signaling without CPU intervention. The peripheral set comprises up to 52 programmable I/O pins, SERCOM (configurable serial communication) channels, a 12-bit 350 kS/s ADC, a 10-bit DAC, four 16-bit Timer/Counters, and a Real-Time Clock. Full-speed USB 2.0 device support and a Peripheral Touch Controller (PTC) for capacitive touch are integrated on most SAM D20J devices, though exact peripheral count on the J14 die is device-specific.
The device leverages Microchip's proprietary Atmel/Microchip low-power design, providing multiple Sleep modes (IDLE, STANDBY, BACKUP) with current consumption down to the low microamp range, suitable for battery-powered end nodes. The integrated Sleepwalking peripheral Event System allows peripherals to wake the CPU only when meaningful events occur, dramatically reducing average power in sensor applications. The Cortex-M0+ pipeline keeps deterministic interrupt latency.
Typical applications include IoT sensor nodes, wearable fitness bands, BLE/Bluetooth proximity beacons, low-cost industrial sensor hubs, and consumer Human Interface Devices (HID) such as keyboards and remote controls. The PTC enables touch button or slider interfaces for white goods and consumer appliances. The compact 5x5 mm UFBGA footprint suits space-constrained designs where PCB area is at a premium.
When designing with this MCU, allocate decoupling capacitors (100 nF + 1 uF) close to each VDD pin and follow Microchip's recommended DFM layout for the UFBGA escape pattern. Consider ATSAMD20J14A-CNT or ATSAMD20J14A-AUT if a different operating temperature grade or pin-package combination is required; these are pin-to-pin compatible with the CUT variant for design reuse.
ドロップイン代替品: ATSAMD20J14A-CUT — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
このシリーズのバリエーション
同一シリーズでドロップイン互換のモデル: ATSAMD20J14A-CUT （同一形状・フットプリント） — 相違点: ADC, Operating Temperature, Package, Mounting Type, RoHS Status.
クイック比較ツール — 並列比較する代替部品を選択:
ATSAMD20J14A-CNT
✅ ドロップイン✓ 在庫あり
$1.95 / 個
データシートを見る →ATSAMD20J14A-AUT
✅ ドロップイン✓ 在庫あり
$1.85 / 個
データシートを見る →ATSAMD20J14A-AUT
✅ ドロップイン✓ 在庫あり
$1.85 / 個
データシートを見る →ATSAMD20J14A-ANT
✅ ドロップイン ⚠️ 仕様未検証📋 参考代替品（カタログ未掲載）
ATSAMD20J17A-CUT
✅ ドロップイン✓ 在庫あり
$2.05 / 個
データシートを見る →ATSAMD20J18A-CUT
✅ ドロップイン📋 参考代替品（カタログ未掲載）
ATSAMD21J16A-CUT
✅ ドロップイン📋 参考代替品（カタログ未掲載）
ATSAMD20J14A-CUT 最大定格＆電気的特性
| Core | ARM Cortex-M0+ (32-bit) |
| Maximum CPU Frequency | 48 MHz |
| Flash Memory | 16 KB |
| SRAM | 2 KB |
| Supply Voltage (VDD) | 1.62 V to 3.63 V |
| 動作温度 | -40C to +85C (industrial) |
| パッケージ | 64-ball UFBGA (5x5 mm) |
| ADC | 12-bit, 350 kS/s (per family) |
| DAC | 10-bit (per family) |
| Timer/Counters | 4 x 16-bit (per family) |
| RTC | Yes, with calendar mode |
| Communication | SERCOM (UART/SPI/I2C configurable) |
| Peripheral Touch Controller | Yes (PTC) |
| 実装タイプ | Surface Mount |
| MSLレベル | MSL3 (per JEDEC J-STD-020) |
| RoHS ステータス | Compliant (Green) |
ATSAMD20J14A-CUT 64-ball ufbga (5x5 mm) ピン配置ガイド
ATSAMD20J14A-CUT (64-ball ufbga (5x5 mm) パッケージ) のピン配置。 このデジタルICには、GPIO、通信インターフェース (UART、SPI、I2C)、および電源ピンが含まれています。代替ピン機能と設定オプションについては、メーカーのデータシートを参照してください。組み込みシステム設計とPCBレイアウトに不可欠です。
詳細なピン配置データはありません: ATSAMD20J14A-CUT.
詳細は データシート をご参照ください。
主な用途
ATSAMD20J14A-CUT の用途: 6 件s: IoT Sensor Node, Wearable Fitness Band, Capacitive Touch Appliance Keypad, USB HID Device, Industrial Sensor Hub, Smart Home Wireless Sensor.
IoT Sensor Node
The ATSAMD20J14A-CUT's Cortex-M0+ core at 48 MHz with Sleepwalking Event System enables ultra-low-power IoT sensor nodes drawing single-digit uA in standby. Its 1.62 V to 3.63 V wide supply range permits direct connection to single-cell Li-ion or 2xAA battery chemistries without boost regulators. The 12-bit ADC at 350 kS/s digitizes temperature, humidity, or motion sensor outputs while the 16 KB Flash holds application firmware and 2 KB SRAM buffers sensor data. Compared to discrete 8-bit MCU designs, the SAM D20 family shrinks BOM by integrating the ADC, RTC, and configurable SERCOM channels in one 5x5 mm UFBGA.
おすすめ
Wearable Fitness Band
The 5x5 mm UFBGA package and Cortex-M0+ low active current make the ATSAMD20J14A-CUT a strong fit for wearable fitness bands where PCB area and battery life are constrained. The integrated 10-bit DAC drives haptic feedback buzzers while the Peripheral Touch Controller supports touch-button or slider interfaces on the band surface. The SERCOM channels connect to BLE modules like the RN4870 for phone sync, and the RTC enables timestamped activity logging. Multiple low-power Sleep modes (IDLE, STANDBY, BACKUP) keep average current below 50 uA in always-on wearables.
おすすめ
Capacitive Touch Appliance Keypad
The ATSAMD20J14A-CUT's Peripheral Touch Controller (PTC) drives capacitive touch buttons and sliders in white-goods appliances without external touch ICs, reducing system cost and PCB area. The 16 KB Flash holds keypad decoding firmware and 2 KB SRAM handles real-time debounce logic. The wide 1.62 V to 3.63 V supply tolerates unregulated 3.3 V rails from small switched-mode supplies common in appliances. Compared to mechanical keypads, PTC-based designs improve reliability against moisture and wear while the -40C to +85C industrial grade handles kitchen and laundry environments.
おすすめ
USB HID Device
Although the J14 die does not include full-speed USB, the ATSAMD20J14A-CUT can drive USB HID peripherals through external SERCOM-to-USB bridges, making it suitable for low-cost keyboards, mice, or remote controls. The Cortex-M0+ at 48 MHz handles HID report generation with deterministic interrupt latency from the NVIC. The 16 KB Flash fits standard HID descriptor tables plus application logic. Compared to 8-bit AVR solutions, the 32-bit M0+ core simplifies USB stack porting and reduces firmware size via Thumb-2 efficiency.
おすすめ
Industrial Sensor Hub
The ATSAMD20J14A-CUT's industrial -40C to +85C temperature grade and 1.62 V to 3.63 V supply suit industrial sensor hubs mounted near machinery where 24 V supply is stepped down to 3.3 V. The 12-bit ADC at 350 kS/s reads multiple analog sensors while SERCOM channels aggregate I2C sensor data from thermocouples, pressure transducers, or load cells. The Cortex-M0+ Event System wakes the CPU only on peripheral triggers, keeping standby current low for battery-backed installations. Compared to PLC analog input modules, this MCU integrates the ADC, RTC, and serial interfaces in one 5x5 mm UFBGA.
おすすめ
Smart Home Wireless Sensor
The ATSAMD20J14A-CUT serves as a low-power host MCU for smart-home sensors using sub-GHz or 2.4 GHz radio companions like the ATSAMR21 or RN2483 LoRa module. The Cortex-M0+ handles sensor sampling, encryption, and radio packet framing while multiple Sleep modes maximize battery life for years-long deployments on coin cells. The compact 64-ball UFBGA package and 16 KB Flash fit typical Zigbee or LoRaWAN sensor firmware stacks. Compared to Wi-Fi-only designs, this approach trades throughput for sub-100 uA average current ideal for door/window or environmental sensors.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: ATSAMD20J14A-CUT — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | ATSAMD20J14A-CNT | ATSAMD20J14A-AUT | ATSAMD20J17A-CUT | ATSAMD20J18A-CUT | ATSAMD21J16A-CUT |
|---|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 64-ball UFBGA (5x5 mm) | 64-ball UFBGA (5x5 mm) - same | 64-ball UFBGA (5x5 mm) - same | 64-ball UFBGA (5x5 mm) - same | 64-ball UFBGA (5x5 mm) - same | 64-ball UFBGA (5x5 mm) - same |
| Core | ARM Cortex-M0+ | ARM Cortex-M0+ | ARM Cortex-M0+ | ARM Cortex-M0+ | ARM Cortex-M0+ | ARM Cortex-M0+ |
| Flash Memory | 16 KB | 16 KB | 16 KB | 32 KB (+100%) | 64 KB (+300%) | 64 KB (+300%) |
| SRAM | 2 KB | 2 KB | 2 KB | 4 KB (+100%) | 8 KB (+300%) | 8 KB (+300%) |
| Maximum CPU Frequency | 48 MHz | 48 MHz | 48 MHz | 48 MHz | 48 MHz | 48 MHz |
| Supply Voltage | 1.62 V to 3.63 V | 1.62 V to 3.63 V | 1.62 V to 3.63 V | 1.62 V to 3.63 V | 1.62 V to 3.63 V | 1.62 V to 3.63 V |
| Operating Temperature | -40C to +85C (industrial) | -40C to +85C | -40C to +125C (automotive) | -40C to +85C | -40C to +85C | -40C to +85C |
| Full-Speed USB Device | No | No | No | No | No | Yes (SAM D21 family) |
主な差別化要因
- Lowest-cost entry in the SAM D20J 64-ball UFBGA family （vs ATSAMD20J17A-CUT)
- Pin-to-pin compatible industrial-temperature variant in tray packaging （vs ATSAMD20J14A-CNT)
- Upgrades to higher memory without PCB rework （vs ATSAMD20J18A-CUT)
設計ノート
Decouple every VDD and VDDCORE pin with a 100 nF ceramic capacitor placed within 3 mm of the pin; add a bulk 4.7 uF or 10 uF capacitor on the main VDD rail. The wide 1.62 V to 3.63 V supply allows direct 1.8 V or 3.3 V operation, but for 2.5 V systems an LDO such as MCP1700 keeps voltage stable under dynamic load. In Sleepwalking designs, gate all unused peripherals via the Clock Mask register to keep standby current below 5 uA.
The 64-ball UFBGA uses a 0.5 mm ball pitch and requires laser-drilled vias or micro-via-in-pad escape for reliable reflow soldering. Per Microchip's SAM D20 hardware design guide, fan-out each BGA signal to inner layers on a 0.4 mm via-pad pitch with 0.2 mm trace-and-space rules. Place the 32.768 kHz crystal traces within 5 mm of the XIN/XOUT pins and guard them with a ground ring to attenuate coupling from switching digital signals.
Do not exceed 3.63 V on any VDD pin - the on-chip brown-out detector and Flash are rated only to 3.63 V. When using the SERCOM modules, configure the peripheral multiplexing in the PORT multiplexer before enabling the SERCOM clock, otherwise the peripheral will not respond. The PTC acquisition pins require firmware calibration for moisture compensation; failing to run the COMPCTRL_Touch calibration sequence causes erratic button readings in humid environments.
コンプライアンス情報
Green/RoHS-compliant per Mouser listing ("GREEN" suffix). Industrial temperature grade -40C to +85C. For AEC-Q100 automotive qualification, choose ATSAMD20J14A-AUT.
