BD37511FS-E2 - 2-Band Car Audio Processor | ROHM Semiconductor
部品番号: BD37511FS-E2 ✓ 生産中BD37511FS-E2 概要
An automotive sound processor belongs to the broader hierarchy of audio processing integrated circuits, analog audio signal-chain ICs, and system audio controllers. Unlike a conventional power amplifier, this device does not directly drive loudspeakers. Instead, it selects and conditions multiple stereo sources, applies volume and equalization functions, and provides control signals suitable for a downstream power-amplifier stage. This separation allows audio routing and tonal control to remain centralized even when the final amplification stage is physically remote from the head unit.
The BD37511FS-E2 provides three input selectors, allowing compatibility with three stereo audio sources. Input-gain control establishes the signal level before tone processing, while main volume and four-channel independent fader control support flexible front-rear and left-right balance adjustments. The internal 2-band equalizer enables tone and bass adjustment without external components, reducing board area and simplifying the analog signal path. Common control software support is intended to improve development efficiency for compatible head-unit platforms.
ROHM describes an Advanced Switch Circuit as an original technology that reduces switching noise in conditions such as no-signal operation, low-frequency signals near 20 Hz, and large-signal transitions. This feature is particularly relevant to source switching and automotive audio systems, where abrupt transitions can otherwise produce audible clicks. The processor combines analog audio routing with digital register control, allowing an external host controller to configure selectors, gains, equalization, and fader positions through the I2C interface.
Typical uses include car-audio head units, automotive source-selection systems, factory-installed radio platforms, and aftermarket audio-interface designs that require independent fader adjustment. Its 7 V to 9.5 V supply range is suited to conventional automotive electrical systems, while its four-channel fader architecture supports front and rear speaker-level control before power amplification. Integration is particularly attractive where a design needs multiple sources, bass and tone adjustment, and compact PCB area.
When implementing the device, maintain a stable supply within the specified 7 V to 9.5 V range and place the required decoupling capacitors close to the supply and ground pins. I2C pull-up and interface layout should follow the manufacturer datasheet, and software should apply gain and attenuation changes in controlled steps where click avoidance is important. Automotive qualification, temperature limits, and detailed absolute-maximum ratings must be confirmed for each vehicle program before production release.
This product overview combines the manufacturer’s functional description with application-oriented design guidance and pinout, packaging, lifecycle, pricing, and replacement information for engineering evaluation. The supplied 20-pin SSOP representation is used for package identification, while the complete numbered pin-description table should be taken from the manufacturer datasheet before PCB routing or production design release.
ドロップイン代替品: BD37511FS-E2 — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
このシリーズのバリエーション
同一シリーズでドロップイン互換のモデル: BD37511FS-E2 （同一形状・フットプリント） — 相違点: Equalizer Bands, Independent Fader Control, Input Gain Control, Input Selector Count, Main Volume Control.
BD37512FS-E2
✅ ドロップイン価格はお問い合わせください
データシートを見る →BD37511FS-E2 最大定格＆電気的特性
| Product Type | Sound processor with built-in 2-band equalizer |
| Supply Voltage Range | 7 V to 9.5 V |
| Control Interface | I2C bus |
| Stereo Input Channels | 3 channels |
| Input Selector Count | 3 selectors |
| Equalizer Bands | 2 bands |
| Independent Fader Control | 4 channels |
| Input Gain Control | Supported |
| Main Volume Control | Supported |
| Switching-Noise Reduction | Advanced Switch Circuit |
| Low-Frequency Switching Condition | Approximately 20 Hz |
| Control Software Support | Common control software supported |
| パッケージ | 20-pin SSOP |
| 実装タイプ | Surface mount |
BD37511FS-E2 20-pin ssop ピン配置ガイド
BD37511FS-E2 (20-pin ssop パッケージ) のピン配置。 このアナログコンポーネントは、入力、出力、および電源ピンを備えています。オフセットナル、補償、イネーブルピンの設定については、メーカーのデータシートを参照してください。信号調整やアンプ回路に最適です。
詳細なピン配置データはありません: BD37511FS-E2.
詳細は データシート をご参照ください。
主な用途
BD37511FS-E2 の用途: 6 件s: Automotive Head-Unit Source Control, Three-Source Radio Interface, Four-Channel Automotive Fader Control, Built-In Two-Band Tone Equalization, Low-Noise Audio Source Switching, Digital-Controlled Automotive Audio Module.
Automotive Head-Unit Source Control
The BD37511FS-E2 fits an automotive head unit that must switch among three stereo sources while maintaining controlled gain and tonal balance. Its three input selectors reduce the number of analog routing stages required, while input-gain control and main volume establish the signal path ahead of the power amplifier. The I2C interface allows the head-unit controller to configure routing and level functions through software rather than discrete switches. In a 7 V to 9.5 V automotive supply environment, the processor provides a centralized function block with a compact 20-pin SSOP footprint. Designers should still validate signal levels, startup behavior, and switching transitions in the complete source module.
おすすめ
Three-Source Radio Interface
The three stereo input selectors in the BD37511FS-E2 are useful when a vehicle audio system accepts radio, auxiliary, and another line-level source. Instead of routing each source through a separate external switching and gain network, the processor can perform selection, gain adjustment, tone shaping, and volume control in one IC. This can reduce analog component count and make source behavior easier to coordinate through the I2C control software. The 2-band equalizer provides additional bass and tone adjustment without external passive networks, although source-specific calibration may still be needed for consistent perceived loudness.
おすすめ
Four-Channel Automotive Fader Control
The BD37511FS-E2 is appropriate for front and rear audio systems that require independent fader control across four channels. Its 4-channel fader architecture allows left-right balance and front-rear level adjustment to be managed digitally, while the main volume and input-gain controls establish the system’s operating range. This is valuable in vehicles where speakers are distributed across the cabin and a single master control cannot provide satisfactory balance. Because fader changes can expose discontinuities, software should use controlled transitions and the hardware should be evaluated for clicks when changing levels quickly.
おすすめ
Built-In Two-Band Tone Equalization
The BD37511FS-E2 integrates a 2-band equalizer for bass and tone adjustment, allowing a compact automotive audio design to alter frequency response without external equalizer components. The processor therefore combines source selection, level management, fader control, and tonal shaping in a single 20-pin SSOP device. This integration is useful in head units where PCB area is constrained but user-adjustable bass and tone controls are required. Equalizer range, center-frequency behavior, and register settings should be taken from the manufacturer datasheet, and the design should be checked for clipping when tone boost and source gain are combined.
おすすめ
Low-Noise Audio Source Switching
The BD37511FS-E2’s Advanced Switch Circuit targets audible switching noise during no-signal conditions, low-frequency operation around 20 Hz, and large-signal transitions. This makes the device relevant to source-switching stages where abrupt changes could otherwise create clicks in a downstream power amplifier. The switching behavior should be evaluated with the actual line-level sources and amplifier gain because the perceived artifact depends on signal amplitude, timing, and system impedance. Software-controlled volume and fader ramps can complement the hardware switching improvement when smooth transitions are required.
おすすめ
Digital-Controlled Automotive Audio Module
The I2C interface makes the BD37511FS-E2 suitable for a digitally managed automotive audio module in which a host controller handles source selection, gain, equalization, and fader settings. Register-based control simplifies coordination with a head-unit microcontroller and supports common control software workflows. The processor operates from 7 V to 9.5 V, aligning with the stated automotive supply range, while its SSOP package supports compact board layouts. Firmware must account for reset defaults and valid control sequences, while the PCB must follow the manufacturer’s recommended I2C and decoupling layout.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: BD37511FS-E2 — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | BD37512FS-E2 |
|---|---|---|
| Product Type | Sound processor with built-in 2-band equalizer | Sound processor with built-in 2-band equalizer |
| Brand | ROHM Semiconductor | ROHM Semiconductor |
| Package | 20-pin SSOP | 20-pin SSOP family |
| Equalizer Bands | 2 bands | 2 bands |
主な差別化要因
- Three stereo input selectors are integrated into one processor （vs BD37512FS-E2)
- Independent four-channel fader control supports vehicle cabin balancing （vs BD37512FS-E2)
- Integrated 2-band equalizer eliminates external tone networks （vs BD37512FS-E2)
- Switching-noise reduction addresses multiple difficult transitions （vs BD37512FS-E2)
設計ノート
Place all required input, output, and supply-decoupling capacitors directly beside their associated pins, with the shortest practical ground return paths. Keep the 20-pin SSOP footprint consistent with the package drawing in the manufacturer datasheet, including lead pitch, span, and solder-land geometry. Confirm pin numbering against the terminal table before routing because the package outline alone does not identify the audio, control, power, or ground terminals.
Treat the I2C bus as a potentially noisy shared control net even though the BD37511FS-E2 performs analog audio processing. Route the bus away from speaker outputs and switching-power nodes, use the pull-up arrangement specified by the manufacturer, and keep the clock and data traces compact. Confirm the host-controller voltage levels and I2C timing before release, particularly when the audio processor shares a bus with other automotive body electronics.
Do not equate equalizer boost with additional headroom. Increasing bass or tone gain can cause clipping when combined with a high input-gain setting or a large line-level source. Establish the maximum expected source amplitude, select conservative initial gain values, and test rapid volume, fader, and source transitions for audible clicks. ROHM’s Advanced Switch Circuit addresses switching conditions, but complete system testing remains necessary because downstream amplifier gain can magnify small discontinuities.
Operate the processor only within its stated 7 V to 9.5 V supply range and verify startup, reset, and load-transient behavior across the complete vehicle electrical environment. The manufacturer datasheet should be used to confirm decoupling values, absolute-maximum limits, and any protection requirements. Avoid deriving automotive surge or reverse-battery tolerance from the nominal operating range alone; those protections may require additional external circuitry.
コンプライアンス情報
The car-audio application is stated by the manufacturer, but explicit RoHS, REACH, AEC-Q100, lead-free, halogen-free, and conflict-minerals declarations were not identified in the manufacturer product-page text.
